This thesis deals with the investigations on the dielectric properties of polycrystalline ceramics having uncommon substitutions in barium titanate and other related phases of BaTiO3-CaTiO3, MgTiO3-CaTiO3 and MgTiO3-BaTiO3 systems. After presenting a brief introduction on the ceramic materials studied in terms of their crystal structures, electrical properties, nonstoichiometry and microstructural characteristics. The thesis describes the synthesis of the ceramics and the methodology of different techniques utilized in characterizing the samples. Barium calcium titanate was synthesized through novel wet chemical techniques and the dielectric properties of calcium substituted barium titanate do not reveal multi-site occupancy whereas they are predominantly influenced by the A/B cationic ratio. The role of transition metals of the 3d series from vanadium (Z=23) to zinc (Z=30) in modifying the crystallographic phase content, microstructure and the dielectric properties of BaTiO3 ceramics containing 10 at% impurities were studied. All the transition metals brought about the phase conversion to hexagonal BaTiO3, although no systematics could be arrived at relating the hexagonal content to the 3d electronic configuration of the impurities. The relaxor dielectrics arising from the titanate solid solution with uncommon substitution and its interconversion to normal ferroelectrics is studied. The effects of cationic substitutions of iron and niobium for titanium in BaTiO3 pervoskite lattice in crystal symmetry and dielectric properties were investigated. The above dielectric characteristics are comparable in a converse way to those of the well known Pb(Mg1/3Nb2/3)O3-PbTiO3 system wherein the relaxor behaviour occurs within the lower lead titanate compositional limits. The modification in -T characteristics of positive temperature coefficient in resistance (PTCR) by the addition of segregative additives such as B2O3, Al2O3 etc in BaTiO3 and its conversion to grain boundary layer capacitance is studied. The presence of Al-related hole centers at the grain boundary regions resulted in charge redistribution across the modified phase transition temperatures due to symmetry-related vibronic interactions, which result in broad PTCR characteristics extending to higher temperatures. The processing of high permittivity ceramics by the manipulation of microstructural features in semiconducting BaTiO3 is studied wherein the grain boundary layer effect superimposed with the contributions from the barrier layers formed during electroding related to microstructure is proposed to be responsible for the unusual high permittivity in semiconducting BaTiO3. The influence of Mg2+ as a substituent in modifying the crystallographic phase contents, microstructure and the dielectric properties of (Ba1-xMgx)TiO3 ceramics, (x ranging from zero to 1.0 ) is studied. The results point to the dual occupancy of Mg2+ both in A and B sublattice and the role of oxygen vacancy as well as (Ti3+ –VO) defects in stabilization of hexagonal phase to lower temperatures. The microwave dielectrics of the BaMg6Ti6O19 phase formed in the compositional range of x=0.4 to 0.7 was investigated for suitable application in microwave dielectrics. Extensive miscibility between the ilmenite-type MgTiO3 and perovskite-type CaTiO3 over a wide compositional range is brought about by the simultaneous equivalent substitution of Al3+ and La3+. The resulting Mg1-(x+y)CaxLay)(Ti1-yAly)O3 ceramics exhibit improved microwave dielectric properties by way of high permittivity, low TCK and high quality factor. The elemental distribution reveals the complexity in the Mg/Ca distribution and its correlation with the solid state miscibility as well as dielectric properties. Microwave dielectric property of Mg4Al2Ti9O25 which is detected as secondary phase is studied in detail.

Pós nanocristalinos de Ba1-xCaxTiO3(0≤ x ≤ 0.30) foram sintetizados pela primeira vez por meio do método dos precursores poliméricos modificados, em temperaturas relativamente baixas (500°C). Para a densificação dos corpos cerâmicos duas técnicas distintas foram utilizadas: a sinterização convencional, utilizando um forno elétrico; e a sinterização a laser, na qual um laser de CO2 foi utilizado como principal fonte de calor. Os corpos cerâmicos sinterizados pelas duas técnicas apresentaram um tamanho médio de grãos em torno de 500 nm, porém uma maior densidade relativa foi obtida nas cerâmicas sinterizadas a laser, chegando a 99%, além de boa transparência, ∼42% a 940 nm para a amostra com 30 mol% de Ca com espessura de 0.5 mm. Também verificamos por meio de simulação numérica, que a equação de condução de calor na aproximação linear, considerando uma fonte de calor com perfil gaussiano, descreve qualitativamente o comportamento observado durante a sinterização a laser no seu estágio final. Por meio da técnica de espectroscopia de impedância foi feita a caracterização dielétrica dos corpos cerâmicos, nos quais três pontos principais foram estudados: i) o efeito do tamanho de grãos; ii) a influência da concentração de Ca; e iii) a influência do método de sinterização. Com a variação do tamanho do grão foram observadas mudanças na intensidade do pico de transição ferro-paraelétrica, na temperatura de Curie e na permissividade relativa à temperatura ambiente. Para concentrações de Ca até 15 mol%, as cerâmicas apresentaram uma transição de Curie estreita semelhante ao BaTiO3,enquanto que para concentrações maiores, uma transição de fase difusa foi observada. A sinterização a laser resultou em corpos cerâmicos com constante dielétrica 30% maior, e menor perda dielétrica do que as cerâmicas sinterizadas convencionalmente. Finalmente, foi proposto um modelo baseando-se na formação de vacâncias de oxigênio para o aumento da condutividade elétrica com a substituição de Ca. / Ba1-xCaxTiO3 (0 ≤ x ≤ 0.30) nanocrystalline powders were successfully synthesized for the first time at relative low temperature (500 °C) by a modified polymeric precursor method. The densification of the ceramics was made by two distinct techniques: conventional sintering using an electric furnace; and by a laser sintering process in which a CO2 laser is used as the main heating source. It was achieved dense ceramics with an average grain size about 500 nm from both techniques. However, the laser sintered ceramics presented a higher relative density (99 %) and a transparency of 42% at 940 nm in the sample with 30 mol% of Ca. By numerical simulation of the thermal conduction equation on the linear approximation case and taking account a thermal source with a gaussian profile, it was possible to describe qualitatively the final stage of the laser sintering process. The dielectric characterization of the ceramic bodies were carried out by the impedance spectroscopy technique and three main effects were studied: i) the grain size effect; ii) the Ca concentration influence; and, iii) the sintering technique influence. Modifying the grain size led to changes in the ferro-paraelectric transition magnitude, on the Curie temperature value and in the relative permittivity at room temperature. For Ca2+ concentrations up to 15 mol% the sintered ceramics presented a sharp Curie transition like BaTiO3,while for higher Ca concentrations a diffuse phase transition was observed. The laser sintered ceramics presented a dielectric constant 30% higher than the conventional sintering and a lower dielectric loss. Finally, we have proposed a model based on the oxygen vacancies formation to explain the conductivity increase with the Ca2+ substitution.

Pós nanocristalinos de Ba1-xCaxTiO3(0≤ x ≤ 0.30) foram sintetizados pela primeira vez por meio do método dos precursores poliméricos modificados, em temperaturas relativamente baixas (500°C). Para a densificação dos corpos cerâmicos duas técnicas distintas foram utilizadas: a sinterização convencional, utilizando um forno elétrico; e a sinterização a laser, na qual um laser de CO2 foi utilizado como principal fonte de calor. Os corpos cerâmicos sinterizados pelas duas técnicas apresentaram um tamanho médio de grãos em torno de 500 nm, porém uma maior densidade relativa foi obtida nas cerâmicas sinterizadas a laser, chegando a 99%, além de boa transparência, ∼42% a 940 nm para a amostra com 30 mol% de Ca com espessura de 0.5 mm. Também verificamos por meio de simulação numérica, que a equação de condução de calor na aproximação linear, considerando uma fonte de calor com perfil gaussiano, descreve qualitativamente o comportamento observado durante a sinterização a laser no seu estágio final. Por meio da técnica de espectroscopia de impedância foi feita a caracterização dielétrica dos corpos cerâmicos, nos quais três pontos principais foram estudados: i) o efeito do tamanho de grãos; ii) a influência da concentração de Ca; e iii) a influência do método de sinterização. Com a variação do tamanho do grão foram observadas mudanças na intensidade do pico de transição ferro-paraelétrica, na temperatura de Curie e na permissividade relativa à temperatura ambiente. Para concentrações de Ca até 15 mol%, as cerâmicas apresentaram uma transição de Curie estreita semelhante ao BaTiO3,enquanto que para concentrações maiores, uma transição de fase difusa foi observada. A sinterização a laser resultou em corpos cerâmicos com constante dielétrica 30% maior, e menor perda dielétrica do que as cerâmicas sinterizadas convencionalmente. Finalmente, foi proposto um modelo baseando-se na formação de vacâncias de oxigênio para o aumento da condutividade elétrica com a substituição de Ca. / Ba1-xCaxTiO3 (0 ≤ x ≤ 0.30) nanocrystalline powders were successfully synthesized for the first time at relative low temperature (500 °C) by a modified polymeric precursor method. The densification of the ceramics was made by two distinct techniques: conventional sintering using an electric furnace; and by a laser sintering process in which a CO2 laser is used as the main heating source. It was achieved dense ceramics with an average grain size about 500 nm from both techniques. However, the laser sintered ceramics presented a higher relative density (99 %) and a transparency of 42% at 940 nm in the sample with 30 mol% of Ca. By numerical simulation of the thermal conduction equation on the linear approximation case and taking account a thermal source with a gaussian profile, it was possible to describe qualitatively the final stage of the laser sintering process. The dielectric characterization of the ceramic bodies were carried out by the impedance spectroscopy technique and three main effects were studied: i) the grain size effect; ii) the Ca concentration influence; and, iii) the sintering technique influence. Modifying the grain size led to changes in the ferro-paraelectric transition magnitude, on the Curie temperature value and in the relative permittivity at room temperature. For Ca2+ concentrations up to 15 mol% the sintered ceramics presented a sharp Curie transition like BaTiO3,while for higher Ca concentrations a diffuse phase transition was observed. The laser sintered ceramics presented a dielectric constant 30% higher than the conventional sintering and a lower dielectric loss. Finally, we have proposed a model based on the oxygen vacancies formation to explain the conductivity increase with the Ca2+ substitution.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Barium titanate (BaTiO3 - BT) is a ferroelectric material with important technological applications. When partially doped with trivalent cations at the barium sublattice or pentavalent at the titanium sublattice, BaTiO3-based ceramics exhibit a semiconductive character, accompanied by a Positive Temperature Coefficient of Resistivity (PTCR). Several ways of BT modifications have been proposed in literature, as example, the use of different synthesis methods and the doping with different ions. Therefore, in the present work we have as objective the synthesis, sintering and electrical characterization of the rare earth ions (RE = La3+, Y3+, Er3+, Nd3+ e Eu3+) doped barium calcium titanate ceramics (Ba0,77Ca0,227RE0,003TiO3 BCT_RE) in order to study mainly the PTCR behavior. The powder synthesis was done by the polymeric precursor method followed by the sinterization at reducing atmosphere during the heating up ramp and different atmosphere during cooling down ramp in order to investigate the atmosphere and dopant effect on PTCR behavior. The characterization was done using the Differential Thermal Analysis, Thermogravimetry, Scanning Differential Calorimetry, X-ray Powder Diffraction, Scanning Electron Microscopy and Impedance Spectroscopy techniques. The calcined powder at 600ºC/4h presented majority BCT phase and after sintering at 1350ºC/6h, a small amount of Ba6Ti17O40 phase was observed. The sintered ceramics presented a homogeneous grain size distribution but with the presence of a secondary phase at the grain boundary for all compositions, and Curie temperature at about 120ºC. The PTCR characteristics of the ceramics were studied as a function of the sintering atmosphere and dopant type. In summary, all the samples, exception of the Eu doped samples, presented PTCR behavior in all the studied conditions. . / O titanato de bário (BaTiO3 - BT) é um material ferroelétrico com importantes aplicações tecnológicas. Quando dopado com íons trivalentes no sítio do bário ou pentavalentes no sítio do titânio, cerâmicas de BaTiO3 exibem um caráter semicondutor, acompanhado por um coeficiente positivo da resistência com o aumento da temperatura (PTCR). Diversas formas de modificação do BT têm sido sugeridas na literatura, por exemplo, a utilização de diferentes métodos de síntese e a dopagem com diferentes íons. Dessa forma, no presente trabalho tivemos como objetivo a síntese, a sinterização e a caracterização elétrica de cerâmicas de titanato de bário e cálcio (Ba0,77Ca0,227RE0,003TiO3 BCT_RE) dopados com íons terras raras (RE = La3+, Y3+, Er3+, Nd3+ e Eu3+), visando principalmente o estudo do comportamento PTCR. A síntese dos pós foi realizada pelo método dos precursores poliméricos, seguido pela sinterização em atmosfera redutora durante o aquecimento e diferentes atmosferas no resfriamento com o intuito de investigar a influência da atmosfera e do dopante no comportamento PTCR. A caracterização foi feita utilizando as técnicas de Análise Térmica Diferencial, Termogravimetria, Calorimetria Exploratória Diferencial, Difração de Raios X, Microscopia Eletrônica de Varredura e Espectroscopia de Impedância. Os pós calcinados a 600ºC/4h apresentaram fase majoritária BCT e após sinterizados a 1350ºC/6h foi observada a presença da fase Ba6Ti17O40. As cerâmicas sinterizadas apresentaram uma distribuição homogênea de tamanho de grão, porém com a presença de uma segunda fase na região de contorno de grão para todas as composições, com temperatura de Curie em torno de 120ºC. As características PTCR das cerâmicas foram estudadas em função da atmosfera de sinterização e do tipo do dopante. Em resumo, todas as amostras, com exceção das dopadas com Eu, apresentaram comportamento PTCR para todas as condições estudadas.

Ferroic materials play an increasingly important role in novel (nano-)electronic applications. Recently, research on domain walls (DWs) received a big boost by the discovery of DW conductivity in bismuth ferrite (BiFeO3 ) and lead zirconate titanate (Pb(Zrx Ti1−x )O3) ferroic thin films. These achievements open a realistic and unique perspective to reproducibly engineer conductive paths and nanocontacts of sub-nanometer dimensions into wide-bandgap materials. The possibility to control and induce conductive DWs in insulating templates is a key step towards future innovative nanoelectronic devices [1]. This work focuses on the investigation of the charge transport along conductive DWs in ferroelectric single crystals. In the first part, the photo-induced electronic DC and AC charge transport along such DWs in lithium niobate (LNO) single crystals is examined. The DC conductivity of the bulk and DWs is investigated locally using piezoresponse force microscopy (PFM) and conductive AFM (c-AFM). It is shown that super-bandgap illumination (λ ≤ 310 nm) in combination with (partially) charged 180° DWs increases the DC conductivity of the DWs up to three orders of magnitude compared to the bulk. The DW conductivity is proportional to the charge of the DW given by its inclination angle α with respect to the polar axis. The latter can be increased by doping the crystal with magnesium (0 to 7 mol %) or reduced by sample annealing. The AC conductivity is investigated locally utilizing nanoimpedance microscopy (NIM) and macroscopic impedance measurements. Again, super-bandgap illumination increases the AC conductivity of the DWs. Frequency-dependent measurements are performed to determine an equivalent circuit describing the domains and DWs in a model system. The mixed conduction model for hopping transport in LNO is used to analyze the frequency-dependent complex permittivity. Both, the AC and DC results are then used to establish a model describing the transport along the conductive DW through the insulating domain matrix material. In the last part, the knowledge obtained for LNO is applied to study DWs in lithium tantalate (LTO), barium titanate (BTO) and barium calcium titanate (BCT) single crystals. Under super-bandgap illumination, conductive DWs are found in LTO and BCT as well, whereas a domain-specific conductivity is observed in BTO.

Ferroic materials play an increasingly important role in novel (nano-)electronic applications. Recently, research on domain walls (DWs) received a big boost by the discovery of DW conductivity in bismuth ferrite (BiFeO3 ) and lead zirconate titanate (Pb(Zrx Ti1−x )O3) ferroic thin films. These achievements open a realistic and unique perspective to reproducibly engineer conductive paths and nanocontacts of sub-nanometer dimensions into wide-bandgap materials. The possibility to control and induce conductive DWs in insulating templates is a key step towards future innovative nanoelectronic devices [1]. This work focuses on the investigation of the charge transport along conductive DWs in ferroelectric single crystals. In the first part, the photo-induced electronic DC and AC charge transport along such DWs in lithium niobate (LNO) single crystals is examined. The DC conductivity of the bulk and DWs is investigated locally using piezoresponse force microscopy (PFM) and conductive AFM (c-AFM). It is shown that super-bandgap illumination (λ ≤ 310 nm) in combination with (partially) charged 180° DWs increases the DC conductivity of the DWs up to three orders of magnitude compared to the bulk. The DW conductivity is proportional to the charge of the DW given by its inclination angle α with respect to the polar axis. The latter can be increased by doping the crystal with magnesium (0 to 7 mol %) or reduced by sample annealing. The AC conductivity is investigated locally utilizing nanoimpedance microscopy (NIM) and macroscopic impedance measurements. Again, super-bandgap illumination increases the AC conductivity of the DWs. Frequency-dependent measurements are performed to determine an equivalent circuit describing the domains and DWs in a model system. The mixed conduction model for hopping transport in LNO is used to analyze the frequency-dependent complex permittivity. Both, the AC and DC results are then used to establish a model describing the transport along the conductive DW through the insulating domain matrix material. In the last part, the knowledge obtained for LNO is applied to study DWs in lithium tantalate (LTO), barium titanate (BTO) and barium calcium titanate (BCT) single crystals. Under super-bandgap illumination, conductive DWs are found in LTO and BCT as well, whereas a domain-specific conductivity is observed in BTO.