Yes / In this work, for the first time, the synthesis of benzyl acetate via the esterification of acetic acid and benzyl alcohol is investigated in the reactive distillation system using a middle vessel (MVD), inverted (IBD), and conventional batch reactive distillation columns. The measurement of the performance of these column schemes is determined in terms of profitability through minimization of the batch time for a defined separation task. The control variables (reboil ratio for MVD, IBD columns) and (reflux ratio in case of CBD column) are considered as piecewise constants over batch time. The optimization results obviously indicate that the CBD system is a more attractive process in terms of batch time reduction, and maximum achievable yearly profit as compared to the MVD, and IBD operations.

No description available.

Yes / The synthesis of ethyl benzoate (EtBZ) via esterification of benzoic acid (BeZ) with ethanol in a reactive distillation is challenging due to complex thermodynamic behaviour of the chemical reaction and the difficulty of keeping the reactants together in the reaction zone (ethanol having the lowest boiling point can separate from the BeZ as the distillation proceeds) causing a significant decrease in the conversion of BeZ in a conventional reactive distillation column (batch or continuous). This might be the reason of not reporting the use of reactive distillation for EtBZ synthesis although the study of BeZ esterification reaction is available in the public literature. Our recently developed Integrated Conventional Batch Distillation (i-CBD) column offers the prospect of revisiting such reactions for the synthesis of EtBZ, which is the focus of this work. Clearly, i-CBD column outperforms the Conventional Batch Distillation (CBD) column in terms of product amount, purity and conversion of BeZ and eliminates the requirement of excess use of ethanol. For example, compared with CBD column, the i-CBD operation can yield EtBZ at a much higher purity (0.925 compared to 0.730) and can convert more benzoic acid (93.57% as opposed to only 74.38%).

Increased interest in unconventional batch distillation column configurations offers new opportunities for increasing the flexibility and energy efficiency of batch distillation. One configuration of particular interest is multivessel batch distillation column, which can be viewed as a generalization of all previously studied batch column configuration. In this work, for the first time the optimal design and operation tasks are developed for multivessel batch distillation with strict product specifications under fixed product demand. Also, in this work, two different operation schemes defined as STN (State Task Network) in terms of the option and numbers of off-cuts were considered for binary and ternary separation. Both the vapour load and number of stages in each column section together with the production sequence are optimised to achieve maximum profit function. The performance of the multivessel batch distillation column is evaluated against the performance of conventional batch column with a simple dynamic model using binary and ternary mixtures. It has been found that profitability improves with the multivessel system in both separations. gPROMS, a user-friendly, software is used for the modeling, simulation, and optimisation.

Batch distillation with chemical reaction when takes place in the same unit is referred to as batch reactive distillation process. The combination reduces the capital and operating costs considerably. Among many different types of batch reactive distillation column configurations, (a) conventional (b) inverted (c) semi-batch columns are considered here. Three reaction schemes such as (a) esterification of methanol (b) esterification of ethanol (c) hydrolysis of methyl lactate are studied here. Four different types of dynamic optimisation problems such as (a) maximum conversion (b) maximum productivity (c) maximum profit and (d) minimum time are formulated in this work. Optimal design and or operation policies are obtained for all the reaction schemes. A detailed rigorous dynamic model consisting of mass, energy balances, chemical reaction and thermodynamic properties is considered for the process. The model was incorporated within the dynamic optimisation problems. Control Vector Parameterisation (CVP) technique was used to convert the dynamic optimisation problem into a nonlinear programming problem which was solved using efficient SQP (Successive Quadratic Programming) method available within the gPROMS (general PROcess Modelling System) software. It is observed that multi-reflux ratio or linear reflux operation always led to better performance in terms of conversion, productivity for all reaction schemes compared to that obtained using single reflux operation. Feed dilution (in the case of ethanol esterification) led to more profit even though productivity was found to be lower. This was due to reduction in feed price because of feed dilution. Semi-batch reactive distillation opertation (for ethanol esterification) led to better conversion compared to conventional batch distillation, however, the total amount of acetic acid (reactant) was greater in semi-batch operation. Optimisation of design and operation (for ethanol esterification) clearly showed that a single cloumn will not lead to profitable operation for all possible product demand profile. Also change in feed and /or product price may lead to adjust the production target to maximise the profitability. In batch distillation, total reflux operation is recommended or observed at the begining of the operation (as is the case for methnaol or ethanol esterification). However, in the case of hydrolysis, total reflux operation was obseved at the end of the operation. This was due to lactic acid (being the heaviest) was withrawn as the final bottom product.

Batch distillation with chemical reaction when takes place in the same unit is referred to as batch reactive distillation process. The combination reduces the capital and operating costs considerably. Among many different types of batch reactive distillation column configurations, (a) conventional (b) inverted (c) semi-batch columns are considered here. Three reaction schemes such as (a) esterification of methanol (b) esterification of ethanol (c) hydrolysis of methyl lactate are studied here. Four different types of dynamic optimisation problems such as (a) maximum conversion (b) maximum productivity (c) maximum profit and (d) minimum time are formulated in this work. Optimal design and or operation policies are obtained for all the reaction schemes. A detailed rigorous dynamic model consisting of mass, energy balances, chemical reaction and thermodynamic properties is considered for the process. The model was incorporated within the dynamic optimisation problems. Control Vector Parameterisation (CVP) technique was used to convert the dynamic optimisation problem into a nonlinear programming problem which was solved using efficient SQP (Successive Quadratic Programming) method available within the gPROMS (general PROcess Modelling System) software. It is observed that multi-reflux ratio or linear reflux operation always led to better performance in terms of conversion, productivity for all reaction schemes compared to that obtained using single reflux operation. Feed dilution (in the case of ethanol esterification) led to more profit even though productivity was found to be lower. This was due to reduction in feed price because of feed dilution. Semi-batch reactive distillation opertation (for ethanol esterification) led to better conversion compared to conventional batch distillation, however, the total amount of acetic acid (reactant) was greater in semi-batch operation. Optimisation of design and operation (for ethanol esterification) clearly showed that a single cloumn will not lead to profitable operation for all possible product demand profile. Also change in feed and /or product price may lead to adjust the production target to maximise the profitability. In batch distillation, total reflux operation is recommended or observed at the begining of the operation (as is the case for methnaol or ethanol esterification). However, in the case of hydrolysis, total reflux operation was obseved at the end of the operation. This was due to lactic acid (being the heaviest) was withrawn as the final bottom product. / Libyan Petroleum Institute

ABSTRACT One of the most important tasks in the chemical industry is the separation of multicomponent liquid mixtures into one or more high-purity products. Several technologies are feasible for this task, either alone or in combination, such as distillation, extraction, crystallization, ect. Among these, distillation is by far the most widely spread and has a long history in chemical technology. However, until recently, there has been no systematic approach for understanding the separation of complex mixtures where azeotropes and multiple liquid phases may occur. There has been a growing interest in the use of residue curve and column profiles for the preliminary design of distillation columns. Residue curves and column profile are not only used to predict the composition changes in the distillation column but also to determine the feasibility of the proposed separation. Recently, theory underlying column profile maps has been developed by Tapp, Holland and co-workers. However there has been no direct experimental validation of the predictions of the column profile map theory. The main aim of this thesis is to experimentally verify some of the predictions of column profile map theory. A simple experimental batch apparatus has been developed to measure residue curve maps (RCMs) by Tapp and co-workers, the apparatus was modified so that it could be used to measure column profile maps (CPMs) in this thesis. CPM theory has shown that CPMs are linear transforms of the residues curve maps (RCMs). A stable node which was the apex of a mass balance triangle (MBT) was introduced inside the MBT, this was done by transforming the RCMs to CPMs using the appropriate distillate composition xd and reflux ratio R. It was also shown that the saddle point which was on the boundary of the triangle of the RCM can be shifted inside the MBT by transforming the RCM to CPM. This is again in accordance with theoretical predictions of CPM theory. iv Residue curves (RCs) and pinch point curves (PPCs) are used to determine the operation leaves and hence the feasible region for distillation columns operating at a specific distillate and bottoms composition for all fixed reflux ratio. The operating leaves were expanded beyond the pinch point curve by varying the reflux ratio from a higher reflux to a lower reflux ratio. This showed that one can effectively cross the pinch point curve hence expanding the operating leave. Finally the importance of experimentally measuring CPMs is demonstrated. Two thermodynamic models were used to predict the profiles of a complex system. The binary vapor-liquid equilibrium (VLE) diagrams and the residue curves produced from using these two thermodynamic models did not predict the same topology. The composition of the profiles were not the same because there were multiple liquid phases involved in this system, which made it difficult for the researchers to measure the correct profiles. Column profile maps were simulated using the different thermodynamic models, they also showed that there is some discrepancy between the predictions of the two models.

This dissertation details research aimed at designing a small batch distillation column to purify tetrafluoroethylene and hexafluoropropylene from a mixture containing tetrafluoroethylene, hexafluoropropylene and octafluorocyclobutane. As no vapour-liquid equilibrium data are available for these chemicals in this mixture, new vapour-liquid equilibrium data were experimentally generated and modelled for use in the design of the batch distillation column. The data were fitted to the Peng-Robinson equation of state, utilizing the Mathias-Copeman alpha function. The model was used with the Wong- Sandler mixing rules alongside the NRTL alpha function. The model was fitted with mean relative deviations lower than 1.2 %, indicating an acceptably accurate description of the VLE data gathered by the model. The experimental data and the model also passed the thermodynamic consistency test for all the systems and isotherms. The design simulations were completed by means of the Aspen Batch Distillation, a module of the Aspen Technologies package. The results show that the optimum design for recovering high-purity products requires six equilibrium stages in the column. The batch column should consist of a still pot, also functioning as a reboiler, a packed column section and a total condenser. The total condenser and the reboiler both count as equilibrium stages. Using this design, a TFE product purity of 99.999 % is predicted with a recovery of 96 %. An HFP product purity of 99 % is predicted at a recovery of 68 %. The recovery of the HFP product can be increased, but entails a significant loss of product purity. The minimum column diameter required to achieve the flow rates suggested in the simulation is 29 mm. The column diameter was selectedas 1¼ ″ (or 31.75 mm) on the basis of the standard pipe diameters available in the industry. Pall ring packing is suggested for use in the column, with an estimated maximum HETP of 0.5 m. As there are five equilibrium stages in the column itself, the column has to be at least 2.5 m high. Copyright / Dissertation (MEng)--University of Pretoria, 2011. / Chemical Engineering / unrestricted

No / Optimal design (vapour load, V and number of stages, N) and operation (reflux ratio, R and batch time, tb) of batch distillation have received significant attention in recent years. In these studies, it has been suggested that V should be set at some upper limit (thought to be optimum) and the optimisation task should be focused on finding the optimum values of N, R and tb, which would minimise the capital investment while maximising an economic objective function usually the profit (P). The major drawback of such optimisation strategy is that there is no constraint on the amount of product (on specification) being produced (NB = no. of batches in a given time) and the overall profit can only be maximised by producing unlimited amount of products. Unplanned and unlimited production of products are not sustainable and may lead to significant losses in the case of large inventory requirements of any excess products produced. In this work, for the first time, the optimal design and operation task for batch distillation is considered with due regards to the market demands (small to large number of batches) of the products being produced. An optimisation problem formulation is presented for the task which is different than those used in the past under unlimited product demand scenario. Simulated Annealing type algorithm is used for the solution of the optimisation problem. With several examples, it will be shown that fixing V a priori (say V < Vopt) will not allow production of NB batches of products with any combination of (N, R, tb) in a given production time. Also it will be shown that with V fixed at say V > Vopt, P will always be <Pmax for any combination of (N, R, tb). The comparisons between the results with and without fixing of V a priori show very clear improvement in the annual profit.

Este trabalho tem por objetivo comparar dois modos de operação de destilação em batelada: com refluxo constante e composição do destilado constante. Desenvolveuse um modelo matemático para a destilação em batelada de uma mistura binária (metanol-etanol) para operação com cada um destes modos. O modelo consiste basicamente dos balanços de massa e entalpia, relações e diagramas de equilíbrio líquido-vapor (composição de equilíbrio, temperaturas de bolha e orvalho da mistura), estimativa das propriedades físico-químicas da mistura (calor específico, calor latente de vaporização), determinação do número de estágios ideais necessários à separação (pelo método de McCabe-Thiele), cálculo de cargas térmicas no refervedor e condensador, consumo de utilidades (vapor de água e água de resfriamento), estimativa do tempo de destilação e alguns aspectos econômicos sobre o processo (custos de equipamentos e operacionais, capacidade de produção, lucro mensal). Implementou-se em uma planilha eletrônica este modelo para as simulações matemáticas e análise técnico-econômica do processo. Em escala de laboratório (foram realizados, ao todo, oito ensaios, quatro de refluxo constante e quatro de refluxo variável, utilizando uma coluna de pratos perfurados), constatou-se uma boa concordância entre estes resultados experimentais e os calculados a partir da modelagem. Em seguida, estudaram-se, isoladamente em cada modo de operação e de modo comparativo, as principais variáveis de processo (taxa de refluxo, composição do destilado, quantidade de carga, vazão de destilado, etc.) através de simulações matemáticas, tanto no cenário de uma unidade existente como no caso do projeto de uma instalação nova. Para uma instalação existente, verificou-se, que no modo de destilação com composição de destilado constante, mantendo-se a vazão do vapor de topo constante, o tempo de destilação é menor, a capacidade de destilação é maior, resultando em maior lucro mensal. Para uma instalação a ser projetada, de novo, o processo mais vantajoso é o de refluxo variável e vazão de vapor do topo constante, pois requer menores áreas dos trocadores de calor para uma dada separação num tempo fixo de processo. No entanto, para o processamento de uma dada quantidade num mesmo tempo, à medida que se adota, no projeto, um número maior de estágios de separação na coluna, a diferença de lucro mensal torna-se praticamente indistinta para os modos de destilação estudados. / The aim of this study is to compare two operational methods of batch distillation of a binary system (methanolethanol): constant reflux and constant distillate composition. A phenomenological modeling concerning each mode was developed. It was based on material and enthalpy balances, equilibrium relationships, estimation of physical properties (specific heat and latent vaporization heat of mixtures), determination of ideal stages number (using McCabe-Thiele method), calculation of rebolier and condenser thermal loads and areas, steam and cooling water requirement, distillation time and some economical aspects. The mathematical model was implemented into an electronic spreadsheet. The predicted values were compared to experimental results from eight tests carried out in a laboratory sieve tray column (four at constant reflux and four at constant distillate composition), and a good consistency was found. Then several case studies concerning each distillation mode as well as the comparative performance were accomplished through mathematical simulations. Evaluation of the basic process variables such as reflux rate, initial load, distillate composition and flow rate was done. Rating of an existing plant and design of a new installation were considered in this process analysis. For an existing installation, lower distillation time, as well as higher distillation capacity and monthly profit were observed when distilling with constant distillate composition, keeping constant the flow rate of vapor from the column top. This process is also the more advantageous one when designing a new plant since smaller heat exchanger areas are required. However, to process a quantity in a same time, in a design of a new plan, as number of separation stages increases, monthly profit becomes almost the same among the studied distillation modes.