The increased fatigue loads and decreased power output of a wind turbine placed in the wake of another turbine is a well-known problem when building new wind-power farms and a subject of intensive research. These problems are caused by the velocity gradients and high turbulence levels present in the wake of a turbine. In order to better estimate the total power output and life time of a wind-power farm, knowledge about the development and stability of wind-turbine wakes is crucial. In the present thesis, the flow field around small-scale model wind turbines has been investigated experimentally in two wind tunnels. The flow velocity was measured with both hot-wire anemometry and particle image velocimetry. To monitor the turbine performance, the rotational frequency, the power output and the total drag force on the turbine were also measured. The power and thrust coefficients for different tip-speed ratios were calculated and compared to the blade element momentum method, with a reasonable agreement. The same method was also used to design and manufacture new turbine blades, which gave an estimate of the distribution of the lift and drag forces along the blades. The influence of the inlet conditions on the turbine and the wake properties was studied by subjecting the turbine to both uniform in flow and different types of boundary layer in flows. In order to study the stability and development of the tip vortices shed from the turbine blades, a new experimental setup for phase-locked measurements was constructed. The setup made it possible to introduce perturbations of different frequencies and amplitudes, located in the rear part of the nacelle. With a newly developed method, it was possible to characterize the vortices and follow their development downstream, using only the streamwise velocity component. Measurements were also performed on porous discs placed in different configurations. The results highlighted the importance of turbine spacings. Both the measurements on the turbine and the discs were also used to compare with large eddy simulations using the actuator disc method. The simulations managed to predict the mean velocity fairly well in both cases, while larger discrepancies were seen in the turbulence intensity. / <p>QC 20140424</p>

This Master’s thesis focuses on the wind turbines. It describes the basic attributes of the wind energy and the wind potential of Slovak Republic, as well as the environmental impact of this sector. Meteorological data for the selected location are processed according to the Weibull distribution and they are used for the aerodynamic design of the wind turbine blades. Aerodynamic design is processed by using two methods. The first is the blade cascade theory, which is used to design prismatic and twist blades. The second method is called the blade element momentum, which is used to design wind turbine but only twist blades are designed by using this theory. Calculated aerodynamic shapes are compared and the best economic solution for the selected location is chosen.

This master‘s thesis focuses on wind turbines. The first part describes the basic attributes of wind energy and wind turbines and is accompanied by a many images. The next section is a statistical processing of measured meteorological data from measuring stations of the Czech Hydrometeorological Institute. These data are then used for calculations of the blades of wind turbines. The calculations are carried by two different methods. The first method is called the blade element momentum theory, the second method is the theory of blade cascade. Using these methods are obtained by two different blades. The last section compares the two blades in terms of geometric and performance.

In this study, an innovative solution is examined for transmission problems and frequency control for wind Turbines. Power electronics and the gear boxes are the parts which are responsible of a significant amount of failures and they are increasing the operation and maintenance cost of wind turbines. Continuously transmission (CVT) systems are investigated as an alternative for conventional gear box technologies for wind turbines in terms of frequency control and power production efficiency. Even though, it has being used in the car industry and is proven to be efficient, there are very limited amount of studies on the CVT implementation on wind turbines. Therefore, this study has also an assertion on being a useful mechanical analyse on that topic. After observing several different types of possibly suitable CVT systems for wind turbines; a blade element momentum code is written in order to calculate the torque, rotational speed and power production values of a wind turbine by using aerodynamic blade properties. Following to this, a dynamic model is created by using the values founded by the help of the blade element momentum theory code, for the wind turbine drive train both including and excluding the CVT system. Comparison of these two dynamic models is done, and possible advantages and disadvantages of using CVT systems for wind turbines are highlighted. The wind speed values, which are simulated according to measured wind speed data, are used in order to create the dynamic models, and Matlab is chosen as the software environment for modelling and calculation processes. Promising results are taken out of the simulations for both in terms of energy efficiency and frequency control. The wind turbine model, which is using the CVT system, is observed to have slightly higher energy production and more importantly, no need for power electronics for frequency control. As an outcome of this study, it is possible to say that the CVT system is a candidate of being a research topic for future developments of the wind turbine technology.

In the present thesis the wake flow behind wind turbines is analyzed numerically using large-eddy simulations. The wind turbine rotors are modeled by using either the actuator disc method or the actuator line method in which the blades are represented by body forces computed with airfoil data. Using these models, the boundary layers of the turbine blades are not resolved and most of the computational power is preserved to simulate the wake flow. The actuator disc method is used for the wake interaction studies of the Lillgrund wind farm. In this study the power production is simulated for two different wind directions and compared to measurements. A grid sensitivity study and a turbulence intensity study are also performed. As a last step the front row turbines are derated in an attempt to increase the total production of the farm. The results show that it is important to impose atmospheric conditions at the inlet in the simulations, otherwise production will be unrealistically low for some turbines in the farm. The agreement between the simulated and measured power is very good. The study based on derating the front row turbines does not show any positive increase on the farm production. The actuator line method is used for near wake analysis of the MEXICO rotor. In this study the near wake is simulated for five different flow cases and compared with particle image velocimetry (PIV) measurements. The analysis is performed by comparing size and circulation of the tip vortices, the radial and streamwise velocity distributions, the spatial expansion of the wake and the axial induction factor. The simulations and measurements generally are in agreement. In some cases, however, the measurements are affected by tunnel effects which are not captured in the simulations. In connection to the actuator disc method a power control strategy for operating conditions below rated power is implemented and tested. The strategy is first validated using an in-house developed blade element momentum code and then is implemented in the actuator disc method used in the EllipSys3D code. The initial tests show that the strategy responds as expected when changing the moment of inertia of the rotor and when varying the inlet conditions. Results from the implementation of the strategy in the actuator disc method in EllipSys3D show that the turbine adapts to the conditions it is operating in by changing its rotational velocity and power output when the inlet conditions are varied. / <p>QC 20130111</p>

When it comes to design a wind turbine rotor, several parameters have to be taken into account. The present work focuses on the inclination of the blades with respect to the rotor plane, namely the pich angle. The main goal of the project was to design a small-scale wind turbine rotor for wind tunnel tests and in this thesis the optimization of a first prototype is presented. The characterization of the performances was carried out by coupling two different approaches: an experimental and a numerical one. For the experimental part, a proper setup was built and the wind turbine model was tested in a wind tunnel. The results were compared with a Blade Element Momentum theory code developed in Python, that involved also CFD simulations to assess the aerodynamic properties of the blade sections. The analysis characterized the performances at variable collective pitch in terms of power and thrust coefficient, showing that the intitial blade design was not the optimal one. Therefore, the optimal pitch angle that maximize the power porduction was found for variable conditions. The second part of the experiments focused on the case of pitch unbalanced and the potential risks connected to it. As a result, the analysis demonstrated that any kind of pitch unbalance generates losses in the power production and may lead to a possible increase of the thrust. To compare the results, a modified BEM code was developed by assuming an axisymmetric axial induction factor. Finally, an additional analysis on the wind turbine oscillations was made, finding a connection between lateral vibrations and rotor unbalance and revealing the resonance frequency of the structure.

Research into advanced wind turbine design has shown that load alleviation strategies like bend-twist coupled blades and coned rotors could reduce costs. However these strategies are based on nonlinear aero-structural dynamics providing additional benefits to components beyond the blades. These innovations will require Multi-disciplinary Design Optimization (MDO) to realize the full benefits. This research expands the MDO capabilities of Horizontal Axis Wind Turbines. The early research explored the numerical stability properties of Blade Element Momentum (BEM) models. Then developed a provincial scale wind farm siting models to help engineers determine the optimal design parameters. The main focus of this research was to incorporate advanced analysis tools into an aero-elastic optimization framework. To adequately explore advanced designs with optimization, a new set of medium fidelity analysis tools is required. These tools need to resolve more of the physics than conventional tools like (BEM) models and linear beams, while being faster than high fidelity techniques like grid based computational fluid dynamics and shell and brick based finite element models. Nonlinear beam models based on Geometrically Exact Beam Theory (GEBT) and Variational Asymptotic Beam Section Analysis (VABS) can resolve the effects of flexible structures with anisotropic material properties. Lagrangian Vortex Dynamics (LVD) can resolve the aerodynamic effects of novel blade curvature. Initially this research focused on the structural optimization capabilities. First, it developed adjoint-based gradients for the coupled GEBT and VABS analysis. Second, it developed a composite lay-up parameterization scheme based on manufacturing processes. The most significant challenge was obtaining aero-elastic optimization solutions in the presence of erroneous gradients. The errors are due to poor convergence properties of conventional LVD. This thesis presents a new LVD formulation based on the Finite Element Method (FEM) that defines an objective convergence metric and analytic gradients. By adopting the same formulation used in structural models, this aerodynamic model can be solved simultaneously in aero-structural simulations. The FEM-based LVD model is affected by singularities, but there are strategies to overcome these problems. This research successfully demonstrates the FEM-based LVD model in aero-elastic design optimization. / Graduate / 0548 / pilot.mm@gmail.com

The predictable nature of the tides offers a regular, reliable source of renewable energy that can be harnessed using tidal stream turbines (TSTs). The UK's practically extractable tidal stream energy resource has the potential to supply around 7 % of the country's annual electricity demand. As of 2016, the world's first commercial scale arrays have been deployed around the UK and France. The harsh nature of the marine operating environment poses a number of engineering challenges, where the optimal turbine design solution remains under investigation. In this thesis, a numerical model is developed to assess the power production and hydrodynamic behaviour of horizontal axis tidal turbines. The developed model builds upon well established and computationally efficient Blade Element Momentum Theory (BEMT) method for modern three-bladed wind turbines. The main novel contribution of this thesis is extending the application to an alternative design of a ducted, high solidity and open centre TST. A validation study using measurements from multiple different scale model experimental tank tests has proven the applicability of the model and suitability of the imposed correction factors. The analytical modifications to account for ducted flow were subsequently indirectly verified, where predictions of turbine power and axial thrust forces under optimal operating speeds were within 2 % of those using more advanced computational fluid dynamics (CFD) methods. This thesis presents a commercial application case of two turbines designed by OpenHydro, examining the BEMT performance with a sophisticated blade resolved CFD study. A comparison of results finds that the model is capable of predicting the average peak power to within 12 %, however it under predicts thrust levels by an average of 35 %. This study concludes that the model is applicable to ducted turbine configurations, but is limited in capturing the complex flow interactions towards the open centre, which requires further investigation. The computational efficiency of the newly developed model allowed a structural analysis of the composite blades, thus demonstrating it is suitable to effectively evaluate engineering applications. Stresses are seen to be dominated by flap-wise bending moments, which peak at the mid-length of the blade. This tool will further enable EDF to perform third party assessments of the different turbine designs, to aid decision making for future projects.

No description available.

No description available.