As aplicações dos dispositivos conversores de energia luminosa, principalmente da luz solar, em energia elétrica são muito variadas e com freqüência surge a possibilidade de uma nova aplicação. Muito tem sido discutido sobre aplicações de células solares em vestimentas, mochilas, tetos de estacionamentos e em embalagens eletrônicas. Esses tipos de aplicações não exigem dispositivos de alto desempenho, porém exigem que seja de baixo custo de processamento e, principalmente, que sejam flexíveis. Dispositivos fotovoltaicos flexíveis devem então ser fabricados por técnicas simples de processamento para permitir sua eventual produção em massa. Esse trabalho pretende dar uma contribuição na escolha dos materiais a serem usados em dispositivos fotovoltaicos flexíveis, focando seu desenvolvimento em células solares orgânicas de heterojunção de volume (BHJ), que são comumente processadas por solução. A estrutura escolhida foi a convencional de multicamadas onde o anodo transparente é o ITO (óxido de índio-estanho), seguida de uma camada transportadora de buracos (PEDOT:PSS), da camada ativa, e do cátodo, que em nosso caso foi formado por cálcio e alumínio, ambos depositados a vácuo. Como camada ativa, principal elemento de estudo nesse trabalho, foram estudados o P3HT:PC61BM, e o PTB7-Th:PC71BM, como elementos doador de elétrons (polímero) e aceitador de elétrons (derivado de fulereno). Em especial com o dispositivo fabricado com o PTB7-Th:PC71BM foi possível elaborar mudanças de processamento e assim melhorar consideravelmente a sua eficiência de conversão de potência. Em seguida, através de medidas de corrente-tensão (J-V) no escuro e sob iluminação, pudemos analisar a evolução dos parâmetros das células, como as resistências série (Rs) e paralelo (Rp), e também aqueles que definem a qualidade da célula solar: a corrente de curto-circuito (Jsc), a tensão de circuito aberto (Voc), o fator de preenchimento (FF), e a eficiência (η). Através dos ajustes das curvas J-V, no escuro e sob iluminação, usando expressões de J(V) extraídas de circuitos equivalentes, respectivamente, dos diodos e das células solares, pudemos realizar uma análise mais efetiva de como as resistências série e paralelo mudam com os elementos da camada ativa e também com diferentes processamentos. O fator de preenchimento (FF) é outro parâmetro importante que determina a eficiência de conversão de energia de uma célula solar orgânica, e existem vários fatores que podem influenciar significativamente o seu valor. Essa é uma das razões do porquê é difícil identificar a real origem desse parâmetro. Essa tese também deu elementos que correlacionam a estrutura química e morfológica da camada ativa com o fator de preenchimento. / The applications of light energy converters, especially the sunlight, in electrical energy are very varied and there is often the possibility of the appearance of new applications. Much has been discussed about solar cell applications in clothing, backpacks, parking ceilings and in electronic packaging. These types of applications do not require high-performance devices, but they do require low-cost processing and, above all, that they are flexible. Flexible photovoltaic devices must then be manufactured by simple processing techniques to allow their eventual mass production. This work intends to contribute to the choice of materials to be used in flexible photovoltaic devices, focusing their development on organic bulk heterojunction solar cells (BHJ), which are commonly processed via solution. The structure chosen for the device was the multilayer one, where the transparent anode is the ITO (indium- tin oxide), followed by a hole transport layer (PEDOT:PSS), the active layer, and the cathode, which in our case was formed by calcium and aluminum, both deposited under vacuum. As active layer, the main element of study in this work, we studied the P3HT: PC61BM and the PTB7-Th: PC71BM, as electron donor (polymer) and electron acceptor elements (derived from fullerene). In particular with the device made with the PTB7-Th:PC71BM it was possible to changes processing parameters and thus enhancing its power conversion efficiency. Then, through current-voltage measurements (J-V), in the dark and under illumination, we were able to analyze the evolution of the cell parameters, such as the series (Rs) and shunt (Rp) resistances, as well as those that define the solar cell quality: short-circuit current (Jsc), open-circuit voltage (Voc), fill factor (FF), and efficiency (η). Through the adjustments of the J-V curves, in the dark and under illumination, using J(V) expressions, for equivalent circuits of the diodes and solar cells respectively, we were able to perform a more effective analysis of how the series and shunt resistances change with the elements of the active layer and also with its processing. Fill factor (FF) is another important parameter that determines the energy conversion efficiency of an organic solar cell, and there are several factors that can significantly influence its value. This is one of the reasons why it is difficult to identify the true source of this parameter. This thesis also gave elements that correlate the chemical and morphological structure of the active layer with the fill factor.

Les cellules photovoltaïques organiques ont fait l'objet d'un intérêt croissant au cours de ces dernières décennies car elles offrent un grand potentiel pour une production d'énergie renouvelable à faible coût. Afin d'obtenir des cellules solaires organiques à haut rendement de conversion d'énergie, beaucoup de recherches se focalisent sur les matériaux ayant des capacités à absorber la lumière efficacement. Dans ce contexte, le présent travail se concentre sur la conception et le développement de nouveaux matériaux donneurs d'électrons (oligomères et polymères) comme matériaux absorbant de la lumière basée sur l'approche « Donneur-Accepteur » alternant des segments riches en électron (donneur d'électron) et des unités pauvres en électron (accepteur d'électron). Trois séries d'unités riches en électron ont été étudiées: oligothiophènes, fluorène et indacenodithiophene. L'unité fluorénone est la principale unité « accepteur d'électron » étudiée. Une comparaison directe avec le système basé sur l'unité benzothiadiazole comme accepteur d'électron est également rapportée. Trois méthodes principales de synthèse ont été utilisées: polymérisation oxydante par le chlorure de fer (III), et les couplages croisés au palladium de type Suzuki ou de Stille. Les études spectroscopique UV-Visible en absorption et en photoluminescence sur ces oligomères et polymères ont démontré la présence de complexes à transfert de charges permettant d'élargir le spectre d'absorption. Les oligomères et les polymères possèdent des faibles largeurs de bande interdite de 1,6 eV à 2 eV. Les systèmes ayant des unités fluorénones présentent des spectres d'absorption étendus allant jusqu'à 600-700 nm, tandis que les systèmes ayant des unités benzothiadiazoles présentent des spectres d'absorption allant jusqu'à 700- 800 nm. La nature des bandes de complexes à transfert de charge se révèle d'être dépendant de la force de respective des unités « donneur d'électrons » et des unités « accepteur d'électrons ». Les niveaux d'énergies HOMO et LUMO des oligomères et les polymères sont déterminés par des mesures électrochimiques. Les polymères à base de fluorène possèdent des niveaux d'énergie HOMO les plus bas. Ces polymères testés en mélange avec les fullerenes PCBM en cellules photovoltaïques ont démontré des valeurs élevées de tension en circuit ouvert (Voc) proche de 0,9 V. Tous les oligomères et les polymères ont été testés dans des dispositifs photovoltaïques et ont montré des résultats encourageants avec des rendements de conversion allant jusqu'à 2,1 %. Ce sont des premièrs résultats obtenus après seulement quelques optimisations (ratios oligomères ou polymères : fullerènes et recuit thermique). Ce travail prometteur permet ainsi d'envisager des résultats plus élevés dans le futur. / Organic photovoltaic (OPV) cells have been a subject of increasing interest during the last decade as they are promising candidates for low cost renewable energy production. In order to obtain reasonably high performance organic solar cells, development of efficient light absorbing materials are of primary focus in the OPV field. In this context, the present work is focused on the design and development of new electron donor materials (oligomers and polymers) as light absorbing materials based on “Donor-Acceptor” approach alternating electron donating group and electron withdrawing group. Three main families of electron donating group are studied: oligothiophenes, fluorene and indacenodithiophene. Fluorenone unit is the principal electron withdrawing group studied and a direct comparison with the system based on benzothiadiazole unit as electron withdrawing unit is also provided. Three main synthetic methods were employed: oxidative polymerization mediated by Iron (III) chloride and Palladium cross-coupling reactions according to Suzuki coupling or Stille coupling conditions. Spectroscopic studies on absorption and photoluminescence have demonstrated the presence of characteristic charge transfer complex in all the studied D-A oligomers and polymers allowing the extension of the absorption spectrum. The D-A oligomers and polymers have shown an overall low optical band gap of 1.6-2 eV with absorption spectra up to 600 to 800 nm. The nature of the charge transfer complex transitions bands were found to be depending on the strength of the electron donating unit and the electron withdrawing unit. Furthermore molecular packing in solution and in solid state has also demonstrated to contribute to extension of absorption spectrum. The HOMO and LUMO energy levels of the oligomers and polymers were determined by electrochemical measurements. Fluorene-based polymers have shown low lying HOMO energy levels, and these polymers demonstrate high open circuit voltage (Voc) in photovoltaic cell when combined with fullerenes derivatives PCBM with Voc values close to 0.9 V. The oligomers and polymers tested in photovoltaic devices have shown promising results with the highest power conversion efficiency obtained of 2.1 % when combined with fullerenes PCBMC70. These results were obtained after only limited numbers of device optimizations such as the active materials ratios and thermal annealing. Therefore further optimization of devices may exhibit higher power conversion efficiencies.

La production durable d’énergie et la recherche d’alternatives aux sources non renouvelables font l’objet d’un grand intérêt à l’heure actuelle. Le principal objectif de cette thèse était de synthétiser et étudier de nouveaux complexes organométalliques à base de Ru-acétylure, puis évaluer leurs propriétés photovoltaïques dans des cellules solaires hybrides à colorant et organique à hétérojonction volumique. Des complexes bimétalliques dissymétriques ont été développés afin d’obtenir des chromophores à absorption panchromatique, en bénéficiant d’une structure « push-pull » et du motif [Ru(dppe)2] comme excellent relai d’électron. En parallèle des complexes symétriques à un ou deux centres métalliques ont été développés, ceux-ci ont ensuite été intégrés à des cellules solaires organiques à hétérojonction volumique. Lors de cette étude, chaque dispositif a fait l’objet de différentes étapes d’optimisations dans le but d’améliorer les transferts de charges en améliorant la morphologie de la couche active. Les principales méthodes d’optimisations appliquées ont consisté à réaliser des traitements par « solvent vapor annealing », ajouter des additifs structurants et utiliser le colorant dans une matrice polymère dans un dispositif à mélange ternaire. / Today the sustainable energy production and research for alternatives to non-renewable sources attract a lot of interest. The aim of this PhD research was to synthetize and study new organometallic complexes Ru-diacetylide based, then to characterize their photovoltaic properties in hybrid dye-sensitized and organic bulk-heterojunction solar cells. To obtain panchromatic chromophores, asymmetric bimetallic complexes have been designed using [Ru(dppe)2] unit as excellent electron relay in a “push-pull” structure. In parallel, symmetric complexes have been developed with one or two metallic centres, and then they have been integrated to organic bulk-heterojunction solar cells. For this study, each device has been optimized through different steps, in order to improve charges transfers by improving morphology of the active layer. The main methods of optimization applied consisted of application of “solvent vapor annealing” treatment, addition of structure additives and addition of the dye in polymer matrix, in ternary molecules blend device.