No description available.

This diploma thesis focuses on the influence of carbon nanotubes (CNTs) on the mechanical properties of a composite material with polyurethane (PU) matrix. The material was supplied in the form of thin films with thickness from 0.2 mm to 1.2 mm. The theoretical part of this thesis describes the production technology, properties and applications of composite materials PU/CNTs, and also deals with preparation technology and properties of both components of this composite material separately. The theoretical part also describes the principle of tensile testing of polymer materials. The experimental part of the thesis was primarily focused on comparing the tensile properties of a composite material PU/CNTs with tensile properties of pure PU. At first, tensile properties of pure PU were investigated, while the influence of various factors like strain rate, specimen thickness, heat treatment and aging was examined. In adition, stress relaxation tests and tests with strain rate jumps were performed on pure PU specimens. Then composite PU/CNTs was tested in tension and the results were compared with the results of tensile tests of pure PU. Composite material PU/CNTs was prepared with various concentrations, so it was possible to determine the effect of CNTs content on the tensile properties of the composite. The last part of this thesis deals with tensile tests of PU composite material with functionalized carbon nanotubes (PU/FCNTs), where the influence of surface modification (functionalization) of CNTs on the tensile properties composites was investigated. It was shown that the effect of both CNT and FCNT on mechanical properties of the composite is not significant. This conclusion was discussed on basis of the works of other authors, which do not unambiguously proved the positive effect of CNT or FCNT on mechanical properties of composites with polymer matrix.

No description available.

No description available.

Carbon nanotubes (CNTs) have gathered a lot of interest because of their extraordinary mechanical, electrical and thermal properties and have potential applications in a wide variety of areas such as material-reinforcement and nano-electronics. The properties of nanotubes are dependent on their diameter and methods for determining this using atomic force microscopy (AFM) in tapping mode assume that the measured height of the tubes represent the real diameter. Based on early, faulty calculations, the forces in tapping mode were assumed to be much lower than in contact mode, however it was later shown that forces in tapping mode can at point of impact rival the forces present in contact mode. This means that there is a potential risk of tube deformation during tapping mode measurements, resulting in incorrectly determined diameters. This work studies CNTs deposited on a silicon-substrate to analyze the effect of three common AFM settings (tapping frequency, free oscillation amplitude and setpoint) to determine their effect on measured CNT diameters and recommendations for choosing settings are given. / Kolnanorör har skapat mycket intresse på grund av sina extraordinära mekaniska, elektriska och termiska egenskaper och har lovande tillämpningar inom en mängd olika områden så som materialförstärkning och nanoelektronik. Kolnanorörens egenskaper påverkas kraftigt av deras diameter och de metoder som använder sig av atomkraftsmikroskopi(AFM) för att mäta diametern hos rören antar att den höjd-data man får fram är ett bra mått på den verkliga diametern hos rören. Baserat på tidiga, felaktiga beräkningar, antog man att kraften i ’tapping mode’ skulle vara mycket lägre än i ’contact mode’ vilket skulle leda till att man inte deformerar ytan man undersöker. Senare forskning visade att kraften mellan spets och prov kan vara lika stor eller rentutav större i tapping mode än i contact mode under det ögonblick då spetsen slår ner i provytan. Det medför att det finns en potentiell risk för att man deformerar kolnanorören när man mäter på dom vilket skulle resultera i att man får felaktiga värden på deras diametrar. Under det här projektet har kolnanorör som placerats på ett kisel-substrat undersökts för att analysera hur tre vanliga inställningar hos AFMet påverkar de erhållna värdena för diametern hos kolnanorören. De tre inställningarna som testats är svängnings-frekvensen, svängnings-amplituden i luft och börvärdet hos svängnings-amplituden.

Carbon nanotubes (CNTs), discovered by Ijima in 1991, are one of the allotropes of carbon, and can be described as cylinders of graphene sheet capped by hemifullerenes. CNTs have excellent electrical, mechanical, thermal and optical properties and very small size. Due to their unique properties and small size, CNTs have a great potential for use in electronics, medical applications, field emission devices (displays,scanning and electronprobes/microscopes) and reinforced composites. CNTs can be grown by different methods from a number of carbon sources such as graphite, CO,C2H4, CH4 and camphor. Under certain conditions, a metallic catalyst is used to initiate the growth. The three main methods used to grow CNTs are: Arc-discharge, laser ablation (LA) and chemical vapour deposition (CVD). In the present work CNTs were grown from a mixture of camphor (C10H16O) and ferrocene (C10H10Fe) using Chemical Vapour Deposition (CVD) and argon was used as a carrier gas. The iron particles from ferrocene acted as catalysts for growth. The substrates used for the growth of CNTs were crystalline Si and SiO2 (Quartz) placed in a quartz tube in a horizontal furnace. Several parameters have been found to affect the CNT growth process. The effects of three parameters: growth temperature, carrier gas (Ar) flow rate and catalyst concentration were investigated in the present work in order to optimize the growth conditions with a simple and economical CVD setup. The samples were characterized using electron microscopy (EM), thermogravimetirc analysis (TGA), Raman and FTIR spectroscopy techniques. It was found that the quality and yield of the CNTs were best at 800°C growth temperature, 80sccm flow rate and 4% catalyst concentration.

This report details work toward the fabrication of a single-electron transistor created from a single-walled carbon nanotube (SWNT). Specifically discussed is a method for growing carbon nanotubes (CNTs) via carbon vapor deposition (CVD). The growth is catalyzed by a solution of 0.02g Fe(NO3)3·9H2O, 0.005g MoO2(acac)2, and 0.015g of alumina particles in 15mL methanol. SWNT diameter ranges from 0.6 to 3.0 nm. Also discussed is a method to control nanotube growth location by patterning samples with small islands of catalyst. A novel “maskless” photolithographic process is used to focus light from a lightweight commercial digital projector through a microscope. Catalyst islands created by this method are approximately 400 μm2 in area.

This report details work toward the fabrication of a single-electron transistor created from a single-walled carbon nanotube (SWNT). Specifically discussed is a method for growing carbon nanotubes (CNTs) via carbon vapor deposition (CVD). The growth is catalyzed by a solution of 0.02g Fe(NO3)3·9H2O, 0.005g MoO2(acac)2, and 0.015g of alumina particles in 15mL methanol. SWNT diameter ranges from 0.6 to 3.0 nm. Also discussed is a method to control nanotube growth location by patterning samples with small islands of catalyst. A novel “maskless” photolithographic process is used to focus light from a lightweight commercial digital projector through a microscope. Catalyst islands created by this method are approximately 400 μm2 in area.

Electrically conductive adhesives (ECA) are an alternative to tin/lead solders for attaching Surface Mount Devices (SMD) in electronic assemblies. ECAs are mixtures of a polymer binder (for adhesion) and conductive filler (for electrical conductivity). They bring more conductivity, higher strength, less weight and longer durability than metal alloys. ECAs can offer numerous advantages such as fewer processing steps, lower processing temperature and fine pitch capability. Multi walled carbon nanotubes (MWCNT) were used as conductive fillers in this research because of their novel electronic and mechanical properties. The high aspect ratio of the nanotubes makes it possible to percolate at low loadings to obtain good electrical and mechanical properties. Replacing the metal filler with CNTs in the adhesive made the ECA light weight, corrosion resistant, reduced processing temperature, lead free, electrically conductive and high mechanical strength. The MWCNTs at different loadings were mixed with epoxy and epoxy: heloxy to form a composite mixture. Different loadings, additives and mixing methods were used to obtain good electrical and mechanical properties and pot life. Pressure dispensing, screen and stencil printing were the processing techniques used for making the samples. The volume resistivity, contact resistance, die shear and lap shear tests were conducted on different surface finished Printed Circuit Boards (PCB) like silver, tin and Electro less Nickel Immersion Gold (ENIG). The results are summarized and compared with traditional methods.

Carbon nanotubes (CNTs) are well known as excellent electrical conductors. However, their transport properties are limited by electrical breakdown in ambient. Moreover, the electronic properties can further be modulated by doping. Devices such as Schottky diodes, transistors and logic gates based on un-doped and doped CNT junctions have been realized. Recently, nitrogen doped CNTs show potential application in replacing platinum cathode catalyst in fuel cell technology. We synthesize pristine, nitrogen-doped and nitrogen-doped:pristine CNT intratubular junctions by one-step co-pyrolysis and explore them for different applications. We show that the position of electrical breakdown can be predicted which is essential to know for high current applications. Among other applications, we show that individual CNT intratubular junction exhibits rectifying characteristics. Further investigation indicates the intratubular junction behaves like Schottky diode. Lastly, the potential replacement of platinum by nitrogen doped CNTs in direct methanol fuel cell has been explored.