Polymers rich in primary amine groups are proposed to be effective adsorbents for the reversible adsorption of CO2 from moderately dilute gas streams (10% CO2) and ultra-dilute gas streams (e.g. ambient air, 400 ppm CO2), with their performance under ultra-dilute conditions being competitive with or exceeding the state-of-the-art adsorbents based on supported poly(ethyleneimine) (PEI). The CO2 adsorption capacity (mmol CO2/g sorbent) and amine efficiency (mmol CO2/mmol amine) of linear poly(allylamine) (PAA), cross-linked poly(allylamine) prepared by post-polymerization crosslinking with epichlorohydrin (PAAEPI), and branched poly(allylamine) prepared by branching of poly(allylamine) with divinylbenzene (PAADVB) are presented here and compared with state-of-the-art adsorbents based on supported PEI, specifically branched and linear, low molecular weight PEI. Silica mesocellular foam, MCF, serves as the support material for impregnation of the amine polymers. In general, branched polymers are found to yield more effective adsorbents materials. Overall, the results of this work show that linear PAA, cross-linked PAAEPI, and branched PAADVB are promising candidates for solid adsorbents with high capacity for CO2.

<p>This thesis encompasses CO₂ mitigation using three different processes: i) natural gas-fired combined cycle with chemical looping combustion (CLC), ii) trigeneration of electrical power, hydrogen and district heating with extended CLC, iii) steam-based gasification of biomass integrated in an advanced power cycle. </p><p>In CLC, a solid oxygen carrier circulates between two fluidised-bed reactors and transports oxygen from the combustion air to the fuel; thus, the fuel is not mixed with air and an inherent CO₂ separation occurs. In this thesis, CLC has been studied as an alternative process for CO₂ capture in a natural gas-fired combined cycle (NGCC). The potential efficiency of such a process using a turbine inlet temperature of 1200 °C and a pressure ratio of 13 is between 52 and 53 % when including the penalty for CO₂compression to 110 bar. It is shown that this efficiency cannot be further improved by including an additional CO₂ turbine. Two conceivable reactor designs for CLC in an NGCC are presented. Top-firing has been studied as an option to overcome a temperature limitation in the CLC reactor system. The degree of CO₂ capture is shown versus the temperature in the CLC reactor and its combustion efficiency. CLC has the potential to reach both a higher efficiency and a higher degree of CO₂capture than conventional post combustion CO₂ capture technique. However, further research is needed to solve technical problems as, for example, temperature limitations in the reactor to reach this potential. </p><p>Extended CLC (exCLC) is introduced, in which hydrogen is not only produced but also inherently purified. The potential efficiency of a novel tri-generation process for hydrogen, electricity and district heating using exCLC for CO₂capture is investigated. The results show that a thermal efficiency of about 54% might be achieved. </p><p>A novel power process named evaporative biomass air turbine (EvGT-BAT) for biomass feedstock is presented. This process contains a steam-based gasification of biomass, which is integrated in an externally fired gas turbine cycle with top-firing. In the EvGT-BAT process, the steam-based gasification is conducted in an entrained-flow tubular reactor that is installed in the SFC as a heat exchanger. The EvGT-BAT process has the potential to generate electrical power from biomass with an efficiency of 41 %.</p>

Absorption-stripping with aqueous, concentrated piperazine (PZ) is a viable retrofit technology for post-combustion CO2 capture from coal-fired power plants. The rate of thermal degradation and oxidation of PZ was investigated over a range of temperature, CO2 loading, and PZ concentration. At 135 to 175 °C, degradation is first order in PZ with an activation energy of 183.5 kJ/mole. At 150 °C, the first order rate constant, k1, for thermal degradation of 8 m PZ with 0.3 mol CO2/mol alkalinity is 6.12 × 10-9 s-1. After 20 weeks of degradation at 165 °C, 74% and 63%, respectively, of the nitrogen and carbon lost in the form of PZ and CO2 was recovered in quantifiable degradation products. N-formylpiperazine, ammonium, and N-(2-aminoethyl) piperazine account for 57% and 45% of nitrogen and carbon lost, respectively. Thermal degradation of PZ likely proceeds through SN2 substitution reactions. In the suspected first step of the mechanism, 1-[2-[(2-aminoethyl) amino]ethyl] PZ is formed from a ring opening SN2 reaction of PZ with H+PZ. Formate was found to be generated during thermal degradation from CO2 or CO2-containing molecules. An analysis of k1 values was applied to a variety of amines screened for thermal stability in order to predict a maximum recommended stripper temperature. Morpholine, piperidine, PZ, and PZ derivatives were found to be the most stable with an allowable stripper temperature above 160 °C. Long-chain alkyl amines or alkanolamines such as N-(2-hydroxyethyl)ethylenediamine and diethanolamine were found to be the most unstable with an allowable stripper temperature below 120 °C. Iron (Fe2+) and stainless steel metals (Fe2+, Ni2+, and Cr3+) were found to be only weak catalysts for oxidation of PZ, while oxidation was rapidly catalyzed by copper (Cu2+). In a system with Fe2+ or SSM, 5 kPa O2 in the inlet flue gas, a 55 °C absorber, and one-third residence time with O2, the maximum loss rate of PZ is expected to 0.23 mol PZ/kg solvent in one year of operation. Under the same conditions but with Cu2+ present, the loss rate of PZ is predicted to be 1.23 mole PZ/kg solvent in one year of operation. Inhibitor A was found to be effective at decreasing PZ loss catalyzed by Cu2+. Ethylenediamine, carboxylate ions, and amides were the only identified oxidation products. Total organic carbon analysis and overall mass balances indicate a large concentration of unidentified oxidation products. / text

The solvent 7 molal (m) methyldiethanolamine (MDEA)/2 m piperazine (PZ) presents an attractive option to industry standard solvents including monoethanolamine (MEA) for carbon dioxide (CO₂) capture in coal-fired power plant flue gas scrubbing applications. The solvent was tested under thermal and oxidizing conditions, including temperature cycling in the Integrated Solvent Degradation Apparatus (ISDA), to measure rates of degradation for comparison to other solvents. Unloaded 7 m MDEA/2 m PZ was generally thermally stable up to 150 °C, exhibiting very low loss rates. However, at a loading of 0.25 mol CO2/mol alkalinity, loss rates of 0.17 ± 0.21 and 0.24 ± 0.06 mM/hr, respectively, for MDEA and PZ were measured. No amine loss was observed in the unloaded blend. Thermal degradation was modeled as first-order in [MDEAH⁺], and a universal Ea for amine loss was estimated at 104 kJ/mol. An oxidative degradation model for 7 m MDEA was developed based on the ISDA data. From the model, the rate of amine loss in 7 m MDEA/2 m PZ was estimated at 1.3 X 10⁵ kg/yr, based on a 500 MW power plant and 90% CO₂ capture. In terms of amine loss, the solvent can be ranked with other cycled solvents from greatest to least as follows: 7 m MDEA>7 m MDEA/2 m PZ>8 m PZ. Thermal degradation pathways and mechanisms for 7 m MDEA/2 m PZ include SN2 substitution reactions to form diethanolamine (DEA), methylaminoethanol (MAE), 1-methylpiperazine (1-MPZ), and 1,4-dimethylpiperazine (1,4-DMPZ). The formation of the amino acids bicine and hydroxyethyl sarcosine (HES) has been directly tied to the formation of DEA and MAE, respectively, through oxidation. As a result of the construction and operation of the ISDA for cycling of solvents from an oxidative reactor to a thermal reactor, several practical findings related to solvent degradation were made. The ISDA results demonstrated that increasing dissolved oxygen in solvents leaving the absorber will increase the rate of oxidation. A simple N2 gas stripping method was tested and resulted in a reduction to 1/5th the high temperature oxidation rate associated with dissolved oxygen present in the higher temperature regions of an absorber/stripper system. The ISDA experiments also demonstrated the need to minimize entrained gas bubbles in absorber/stripper systems to control oxidation. When the ISDA was modified to intercept entrained gas bubbles, the oxidation rate was reduced 2 to 3X. / text

Microporous organic polymers (MOPs) are porous materials. Owing to their high surface area, tunable pore sizes and high physicochemical stability, they are studied for applications including gas capture and separation and heterogeneous catalysis. In this thesis, a series of imine/azo-linked MOPs were synthesized. The MOPs were examined as potential CO2 sorbents and as supports for heterogeneous catalysis. The MOPs were synthesized by Schiff base polycondensations and oxidative couplings. The porosities of the imine-linked MOPs were tunable and affected by a range of factors, such as the synthesis conditions, monomer lengths, monomer ratios. All the MOPs had ultramicropores and displayed relatively high CO2 uptakes and CO2-over-N2 selectivities at the CO2 concentrations relevant for post-combustion capture of CO2. Moreover, the ketimine-linked MOPs were moderately hydrophobic, which might increase their efficiency for CO2 capture and separation. The diverse synthesis routes and rich functionalities of MOPs allowed further post-modification to improve their performance in CO2 capture. A micro-/mesoporous polymer PP1-2, rich in aldehyde end groups, was post-synthetically modified by the alkyl amine tris(2-aminoethyl)amine (tren). The tethered amine moieties induced chemisorption of CO2 on the polymer, which was confirmed by the study of in situ infrared (IR) and solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. As a result, the modified polymer PP1-2-tren had a large CO2 capacity and very high CO2-over-N2 selectivity at low partial pressures of CO2. Pd(II) species were incorporated in the selected MOPs by means of complexation or chemical bonding with the imine or azo groups. The Pd(II)-rich MOPs were tested as heterogeneous catalysts for various organic reactions. The porous Pd(II)-polyimine (Pd2+/PP-1) was an excellent co-catalyst in combination with chiral amine for cooperatively catalyzed and enantioselective cascade reactions. In addition, the cyclopalladated azo-linked MOP (Pd(II)/PP-2) catalyzed Suzuki and Heck coupling reactions highly efficiently. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 4: Accepted. Paper 7: Manuscript.</p>

A range of porous solid adsorbents were synthesised and their ability to separate and capture carbon dioxide (CO2) from gas mixtures was examined. CO2 separation from flue gas – a type of exhaust gas from fossil fuel combustion that consists of CO2 mixed with mainly nitrogen and biogas (consists of CO2 mixed with mainly methane) were explicitly considered. The selected adsorbents were chosen partly due to their narrow pore sizes. Narrow pores can differentiate gas molecules of different sizes via a kinetic separation mechanism: a large gas molecule should find it more difficult to enter a narrow pore. CO2 has the smallest kinetic diameter in zeolites when compared with the other two gases in this study. Narrow pore adsorbents can therefore, show enhanced kinetic selectivity to adsorb CO2 from a gas mixture. The adsorbents tested in this study included mixed cation zeolite A, zeolite ZK-4, a range of aluminophosphates and silicoaluminophosphates, as well as two types of titanium silicates (ETS-4, CTS-1). These adsorbents were compared with one another from different aspects such as CO2 capacity, CO2 selectivity, cyclic performance, working capacity, cost of synthesis, etc. Each of the tested adsorbents has its advantages and disadvantages. Serval phosphates were identified as potentially good CO2 adsorbents, but the high cost of their synthesis must be addressed in order to develop these adsorbents for applications. / <p>At the time of the doctoral defence the following papers were unpublished and had a status as follows: Papers 4-8: Manuscripts.</p>

The main theme of this dissertation is the fabrication and analysis of modified mesoporous silica membranes for separation applications. Synthesis methods for mesoporous silica membranes have been developed to enhance the transport performance and quality of the membranes, such as permeability, pore volume, and surface area. Then, synthesized membranes were modified with different organic groups to tailor selectivity in separations. The collected studies of modified mesoporous silica membranes showed that appropriate functionalization on newly synthesized novel membranes leads to promising structural and permeation properties. First, a seeded growth method was developed for synthesis of MCM-48 membranes on alumina supports, thereby extending the seeded growth technique used for zeolite membranes to mesoporous silica membrane synthesis. The surface properties of the MCM-48 membranes were then modified by silylation with hexamethyldisilazane (HMDS). In comparison to MCM-48 membranes previously synthesized by the in situ growth technique, much less silica infiltration into the alumina support was observed. The pore structure of the MCM-48 membranes demonstrated that a large accessible pore volume was available for molecular permeation and pore modification to tailor selectivity. The gas permeation properties of the calcined and silylated MCM-48 membranes were consistent with a Knudsen-like mechanism, albeit with a substantial influence of gas-solid interactions in the mesopores. The silylated MCM-48 membranes were evaluated for pervaporative separation of ethanol (EtOH), methyl ethyl ketone (MEK), and ethyl acetate (EA) from their dilute aqueous solutions. The synthesized membranes exhibited high pervaporative separation factors and organic fluxes. The selective separation of organic/water mixtures with MCM-48 membranes were attributed to both the organophilic nature of the surface and the effective pore size of the silylated mesopores. Next, the synthesis and organic/water separation properties of mesoporous silica membranes supported on low-cost and scalable polymeric (polyamide-imide) hollow fibers and modified by trimethylsilylation with HMDS was studied. Thin, defect-free membranes that exhibited high gas permeances consistent with Knudsen-like diffusion through the mesopores were prepared. Silylation of these membranes did not affect the integrity of the mesoporous silica structure and the underlying polymeric hollow fiber, but led to capping of the surface silanol groups in the mesopores with trimethylsilyl groups. The silylated mesoporous membranes were evaluated for pervaporative separation of EtOH, MEK, EA, iso-butanol, and n-butanol from their dilute aqueous solutions. The membranes showed higher separation factors than those of flat membranes, along with high organic fluxes. The large increase in hydrophobicity of the membranes upon silylation allowed upgrading of the feed mixtures to permeate streams with considerably higher organic content. The selective separation of organic/water mixtures with the fiber-supported mesoporous silica membranes was attributed to both the organophilic nature of the surface (yielding good adsorption selectivity) and the effective pore size of the silylated mesopores (giving good fluxes). Comparison with other types of organic/water separation membranes revealed that the present silylated membrane platform shows good promise for use in organic/water separation applications due to its high flux, scalable and low-cost fabrication methodology, and good separation factors that can be further enhanced by tailoring the mesopore modification chemistry. Further, the gas transport properties of aziridine-functionalized mesoporous silica membranes on polymeric hollow fibers have also investigated. The mesoporous membranes were amine-functionalized with aziridine and their transport properties were studied to understand the effects of surface functionalization on gas separations. This new hybrid aminosilica membrane showed interesting and counter-intuitive N₂ selective permeation properties in dry CO₂/N₂ separations. Detailed characterization of the membrane structure and its permeation behavior showed that such behavior was due to the strong adsorption of CO₂, leading to reduced gas flux because of CO₂-induced amine crosslinking in the mesopores. This hyper-branched aminosilica membrane showed CO₂ selective properties when applied to humid gas permeation. Water molecules in the humid gas affected the adsorption of CO₂ molecules by causing a lower degree of crosslinking, allowing facilitated transport of CO₂.

Australia is recognising that carbon capture and storage (CCS) may be a feasible pathway for addressing increasing levels of CO2 emissions. This thesis presents a preliminary economic assessment and comparison of the capture costs for different Australian CO2 emission sources. The capture technologies evaluated include solvent absorption, pressure swing adsorption (PSA), gas separation membranes and low temperature separation. The capture cost estimated for hydrogen production, IGCC power plants and natural gas processing is less than A$30/tonne CO2 avoided. CO2 capture cost for iron production ranges from A$30 to A$40 per tonne CO2 avoided. Higher costs of A$40 to over A$80 per tonne CO2 avoided were estimated for flue gas streams from pulverised coal and NGCC power plants, oil refineries and cement facilities, and IDGCC synthesis gas. Based on 2004 and 2005 EU ETS carbon prices (A$30 to A$45 per tonne CO2 avoided), the cost of capture using current commercially available absorption technology may deter wide-scale implementation of CCS, in particular for combustion processes. A sensitivity analysis was undertaken to explore the opportunities for reducing costs. The high cost for capture using solvent absorption is dependent on the energy needed for solvent regeneration and the high capital costs. Cost reductions can be achieved by using new low regeneration energy solvents coupled with recycling the waste heat from the absorption process back to the steam cycle, and using low cost ???fit-for-purpose??? equipment. For membrane and PSA technologies, the capture costs are dominated by the flue gas and post-capture compressors. Operating the permeate or desorption stream under vacuum conditions provides significant cost reductions. Improvements in membrane and adsorbent characteristics such as the adsorbent loading or membrane permeability, CO2 selectivity, and lower prices for the membrane or adsorbent material provide further cost benefits. For low partial pressure CO2 streams, capture using low temperature ???anti-sublimation??? separation can be an alternative option. Low costs could be achieved by operating under low pressures and integrating with external sources of waste heat. Applying the cost reductions achievable with technology and process improvements reduces the capture and CCS costs to a level less than current carbon prices, making CCS an attractive mitigation option.

abstract: This investigation is divided into two portions linked together by the momentous reaches of electrochemistry science, principles influencing everyday phenomena as well as innovative research in the field of energy transformation. The first portion explores the strategies for flue gas carbon dioxide capture and release using electrochemical means. The main focus is in the role thiolates play as reversible strong nucleophiles with the ability to capture CO2 and form thiocarbonates. Carbon dioxide in this form is transported and separated from thiocarbonate through electrochemical oxidation to complete the release portion of this catch-and-release approach. Two testing design systems play a fundamental role in achieving an efficient CO2 catch and release process and were purposely build and adapted for this work. A maximum faradaic efficiency of seventeen percent was attained in the first membrane tests whose analysis is presented in this work. An efficiency close to thirty percent was attained with the membrane cell in recent experiments but have not been included in this manuscript. The second portion of this manuscript studies bulk stress evolution resulting from insertion/extraction of lithium in/from a lithium manganese oxide spinel cathode structure. A cantilever-based testing system uses a sophisticated, high resolution capacitive technique capable of measuring beam deflections of the cathode in the subnanometer scale. Tensile stresses of up to 1.2 MPa are reported during delithiation along with compressive stresses of 1.0 MPa during lithiation. An analysis of irreversible charge loss is attributed to surface passivation phenomena with its associated stresses of formation following patterns of tensile stress evolution. / Dissertation/Thesis / Doctoral Dissertation Materials Science and Engineering 2016

Processos como a purificação do metano (CH4) e a produção de hidrogênio gasoso (H2) envolvem etapas de separação de CO2. Atualmente, etanolaminas como monoetanolamina (MEA), dietanolamina (DEA), metildietanolamina (MDEA) e trietanolamina (TEA) são as substâncias mais utilizadas no processo de separação/captura de CO2 em processos industriais. Entretanto, o uso destas substâncias apresenta alguns inconvenientes devido à alta volatilidade, dificuldade de se trabalhar com material líquido, também ao alto gasto energético envolvido das etapas de regeneração e à baixa estabilidade térmica e química. Com base nessa problemática, esse trabalho teve por objetivo a síntese de um tipo de sílica mesoporosa altamente ordenada (SBA-15) de modo a utilizá-la no processo de captura de CO2. O trabalho foi dividido em quatro etapas experimentais que envolveram a síntese da SBA-15, o estudo do comportamento térmico de algumas etanolaminas livres, síntese e caracterização de materiais adsorventes preparados a partir de incorporação de etanolaminas à SBA-15 e estudo da eficiência de captura de CO2 por esses materiais. Novas alternativas de síntese da SBA-15 foram estudadas neste trabalho, visando aperfeiçoar as propriedades texturais do material produzido. Tais alternativas são baseadas na remoção do surfatante, utilizado como molde na síntese da sílica mesoporosa, por meio da extração por Soxhlet, utilizando diferentes solventes. O processo contribuiu para melhorar as propriedades do material obtido, evitando o encolhimento da estrutura que pode ser ocasionado durante a etapa de calcinação. Por meio de técnicas como TG/DTG, DSC, FTIR e Análise Elementar de C, H e N foi realizada a caracterização físico-química e termoanalítica da MEA, DEA, MDEA e TEA, visando melhor conhecer as características destas substâncias. Estudos cinéticos baseados nos métodos termogravimétricos isotérmicos e não isotérmicos (Método de Ozawa) foram realizados, permitindo a determinação de parâmetros cinéticos envolvidos nas etapas de volatilização/decomposição térmica das etanolaminas. Além das técnicas acima mencionadas, MEV, MET, SAXS e Medidas de Adsorção de N2 foram utilizadas na caraterização da SBA-15 antes e após a incorporação das etanolaminas. Dentre as etanolaminas estudadas, a TEA apresentou maior estabilidade térmica, entretanto, devido ao seu maior impedimento estérico, é a etanolamina que apresenta menor afinidade com o CO2. Diferentemente das demais etanolaminas estudadas, a decomposição térmica da DEA envolve uma reação intramolecular, levando a formação de MEA e óxido de etileno. A incorporação destes materiais à SBA-15 aumentou a estabilidade térmica das etanolaminas, uma vez que parte do material permanece dentro dos poros da sílica. Os ensaios de adsorção de CO2 mostraram que a incorporação da MEA à SBA-15 catalisou o processo de decomposição térmica da mesma. A MDEA foi a etanolamina que apresentou maior poder de captura de CO2 e sua estabilidade térmica foi consideravelmente aumentada quando a mesma foi incorporada à SBA-15, aumentando também seu potencial de captura de CO2. / Processes as methane (CH4) purification from natural gas and gas hydrogenous (H2) production have stages involving CO2 separation. Nowadays, ethanolamine as monoethanolamine (MEA), diethanolamine (DEA), methyldiethanolamine (MDEA) and triethanolamine (TEA) are the substances more used in industrial processes involving CO2 separation/purification. However, the use of these substances has some inconvenient due to high volatility of these species, the inconvenient working with liquid, the use of high energy during the regeneration processes and low chemical and thermal stability. The object of this work was the synthesis of mesoporous ordinated silica (SBA-15) and its use in the CO2 capture process. This work was divided in four experimental stages: SBA-15 synthesis, the study of ethanolamine thermal behavior, the synthesis and characterization of adsorbent materials prepared using SBA-15 and ethanolamine and the study about the efficiency of CO2 capture using these materials. New alternatives for SBA-15 synthesis were studied in this work, due to increase the material proprieties. This study had the objective removing part of the surfactant used as template in mesoporous materials synthesis, using Soxhlet extractor and different solvents. This work contributed to increase the silica proprieties, eviting the shrinkage of silica structure caused by calcination stage. By means of TG/DTG, DSC, FTIR and Elemental Analysis techniques was realized physical-chemical and thermal characterization of MEA, DEA, MDEA and TEA. Kinetics studies using thermalgravimetric isothermal and no isothermal (Ozawa Method) method were used. This study permitted the determination of kinetics parameters involved in the thermal decomposition of the ethanolamines. Additionally, techniques as SEM, TEM, SAXS and Isotherm Adsorption of N2 were used for the characterization of SBA-15 incorporated with ethanolamine.TEA was the ethanolamine the biggest thermal stability, however, the CO2 absorption is not favorable because the steric impediment. The thermal decomposition of DEA involves the intramolecular reaction, producing MEA and ethylene oxide. The ethanolamines incorporation in SBA-15 increased the thermal stability of the ethanolamines, because part of these substances was in the SBA-15 porous. The experiments of CO2 capture showed that the MEA incorporation in the SBA-15 catalyzed the MEA decomposition process. The MDEA was the ethanolamine that had the major efficiency in the CO2 capture and its thermal stability was considerably increased when this space was incorporated in SBA-15, increasing its CO2 capture potential.