No processo de beneficiamento da vermiculita é gerado um resíduo fino para o qual atualmente ainda não foi desenvolvida uma aplicação que possibilite a utilização em larga escala. Uma alternativa que vem sendo estudada é a associação com cimento Portland em composições de argamassas e concretos, em função da composição química do resíduo: elevada quantidade de alumínio, silício e magnésio, que podem apresentar interações com o ligante. No entanto, em função da elevada área superficial específica, em comparação ao cimento, sua utilização nas composições pode afetar a demanda de água de amassamento e limitar a sua aplicação. Para tanto, uma alternativa é a calcinação deste resíduo fino, assim como é realizado para outras argilas (caulim, por exemplo), para que a área superficial específica (ASE) seja menor e eventualmente ative propriedades pozolânicas na respectiva argila. Deste modo, neste trabalho foram avaliadas as diversas características de pastas cimentícias após adição de resíduo fino de vermiculita: reação química, formação dos produtos hidratados, propriedades reológicas, tanto após a mistura como ao longo da hidratação. Foi verificado que de forma geral a reação química não é afetada após a adição de vermiculita, embora a formação de aluminatos seja intensificada na composição com maior quantidade de resíduo in natura. Com relação ao seu comportamento no estado fresco, foi observado que a maior ASE do resíduo impacta fortemente as propriedades reológicas das pastas, embora que com um teor de 5% as mudanças sejam menores. Utilizando-se dessas mesmas composições para a avaliação do desempenho no estado endurecido de argamassas, foi verificado que não há efeito sobre essas propriedades até 5% de substituição, independentemente do tratamento térmico empregado. Assim, considerando aspectos econômicos de transporte assim como os custos decorrentes da calcinação, pode-se recomendar a adição de 5% de vermiculita in natura sem comprometer o desempenho dos produtos, embora não se possa precisar com os dados obtidos a sua durabilidade ao longo do uso. / In the process to obtaining vermiculite a fine residue is generated, which does not yet have a large-scale application. An alternative that has been studied is the association with Portland cement in mortar and concrete formulations, as a function of the chemical composition of the residue: high amount of aluminium, silicon and magnesium which may have interactions with the binder. However, the residue has a high specific surface area, in comparison to cement, a fact that can increase the water-demand to mix and limit its application. For this, an alternative is the calcination of this fine residue, as it is done for other clays (kaolin, for example), so that the specific surface area (SSA) is smaller and eventually activates pozzolanic properties in the respective clay. Thus, in this work the various characteristics of cement pastes after addition of vermiculite fine residue were evaluated: chemical reaction, formation of the hydrated products, rheological properties, both after mixing and along the hydration. It was verified that in general the chemical reaction is not affected after the addition of vermiculite, although the formation of aluminates is intensified in the composition with greater amount of in nature residue. Regarding its behaviour in the fresh state, it was observed that the higher SSA of the residue strongly impacts the rheological properties of the pastes, although with a 5% content the changes are minimal. Using these same compositions to evaluate the performance in the hardened state of mortars, it was verified that there is no effect on these properties up to 5% of substitution, regardless of the thermal treatment used. Thus, considering the economic aspects of transport as well as the costs of calcination, it is possible to recommend the addition of 5% of vermiculite in nature without compromising the performance of the products, although it is not possible to determine the its durability during the use.

No processo de beneficiamento da vermiculita é gerado um resíduo fino para o qual atualmente ainda não foi desenvolvida uma aplicação que possibilite a utilização em larga escala. Uma alternativa que vem sendo estudada é a associação com cimento Portland em composições de argamassas e concretos, em função da composição química do resíduo: elevada quantidade de alumínio, silício e magnésio, que podem apresentar interações com o ligante. No entanto, em função da elevada área superficial específica, em comparação ao cimento, sua utilização nas composições pode afetar a demanda de água de amassamento e limitar a sua aplicação. Para tanto, uma alternativa é a calcinação deste resíduo fino, assim como é realizado para outras argilas (caulim, por exemplo), para que a área superficial específica (ASE) seja menor e eventualmente ative propriedades pozolânicas na respectiva argila. Deste modo, neste trabalho foram avaliadas as diversas características de pastas cimentícias após adição de resíduo fino de vermiculita: reação química, formação dos produtos hidratados, propriedades reológicas, tanto após a mistura como ao longo da hidratação. Foi verificado que de forma geral a reação química não é afetada após a adição de vermiculita, embora a formação de aluminatos seja intensificada na composição com maior quantidade de resíduo in natura. Com relação ao seu comportamento no estado fresco, foi observado que a maior ASE do resíduo impacta fortemente as propriedades reológicas das pastas, embora que com um teor de 5% as mudanças sejam menores. Utilizando-se dessas mesmas composições para a avaliação do desempenho no estado endurecido de argamassas, foi verificado que não há efeito sobre essas propriedades até 5% de substituição, independentemente do tratamento térmico empregado. Assim, considerando aspectos econômicos de transporte assim como os custos decorrentes da calcinação, pode-se recomendar a adição de 5% de vermiculita in natura sem comprometer o desempenho dos produtos, embora não se possa precisar com os dados obtidos a sua durabilidade ao longo do uso. / In the process to obtaining vermiculite a fine residue is generated, which does not yet have a large-scale application. An alternative that has been studied is the association with Portland cement in mortar and concrete formulations, as a function of the chemical composition of the residue: high amount of aluminium, silicon and magnesium which may have interactions with the binder. However, the residue has a high specific surface area, in comparison to cement, a fact that can increase the water-demand to mix and limit its application. For this, an alternative is the calcination of this fine residue, as it is done for other clays (kaolin, for example), so that the specific surface area (SSA) is smaller and eventually activates pozzolanic properties in the respective clay. Thus, in this work the various characteristics of cement pastes after addition of vermiculite fine residue were evaluated: chemical reaction, formation of the hydrated products, rheological properties, both after mixing and along the hydration. It was verified that in general the chemical reaction is not affected after the addition of vermiculite, although the formation of aluminates is intensified in the composition with greater amount of in nature residue. Regarding its behaviour in the fresh state, it was observed that the higher SSA of the residue strongly impacts the rheological properties of the pastes, although with a 5% content the changes are minimal. Using these same compositions to evaluate the performance in the hardened state of mortars, it was verified that there is no effect on these properties up to 5% of substitution, regardless of the thermal treatment used. Thus, considering the economic aspects of transport as well as the costs of calcination, it is possible to recommend the addition of 5% of vermiculite in nature without compromising the performance of the products, although it is not possible to determine the its durability during the use.

Doctor of Philosophy / Department of Horticulture, Forestry, and Recreation Resources / Kimberly A. Williams / The use of calcined clays contributes properties of nutrient and water retention to soilless root media, which varies greatly depending on the parent clay and calcining treatment. This research characterized phosphate (PO[subscript]4) sorption of various calcined clay products, including low volatile and regular volatile material (LVM and RVM) 2:1 Attasorb clays (Engelhard Corp.), 2:1 Terra Green LVM clays (Oil-Dri Co.), and Turface (Profile Products LLC) at various particle sizes; 1:1 kaolin clays (Thiele Kaolin Co.) in powder form, and diatomaceous earth (Diatomite, Eagle Picher Minerals, Inc.). Three of the calcined materials, Terra Green montmorillonite and Attasorb attapulgite (which had high PO[subscript]4-sorption based on isotherms), and diatomaceous earth (which had negligible PO[subscript]4-sorption) were evaluated as components of soilless root media in two separate greenhouse experiments. The effect of the calcined materials, rate of incorporation (0%, 5%, 10% and 20% by volume in a mix with peat and perlite), and PO[subscript]4-P application rate (0, 5, 15, 45 mg.L[superscript]-1 PO[subscript]4-P) on plant growth, effluent P content and water use were determined during production and post-production of Impatiens wallerana Hook f. 'Tempo Rose'. The calcined materials varied in their ability to adsorb PO[subscript]4-P and generally yielded L-type isotherms. Laboratory results indicated potential for substantive P retention by several of the calcined materials when used in container production. For most materials, PO[subscript]4-P sorption did not show pronounced pH dependence. During production and post-production, the test materials not only improved PO[subscript]4-P retention but also water retention and water use efficiency while still maintaining optimal physical properties at incorporation rates of 5 to 10%. Diatomaceous earth resulted in PO[subscript]4-P retention not significantly different from the calcined clays.

<p>  </p> <p>Concrete is the second most consumed material in the world after water and is an essential element of constructed infrastructure. Over 14 billion m3 of concrete are being produced annually, resulting in a serious impact on the environment. The production of cement, which is the main component of concrete, is responsible for 5 – 8 % of global CO2 emissions. As a result, several global initiatives have been undertaken to achieve carbon neutrality by 2050. This carbon neutrality target coincides with the Paris Agreement's goal to limit global warming to 1.5 °C. A well-known, and successful strategy to reduce CO2 emissions in the concrete industry is to use supplementary cementitious materials (SCMs) as a partial replacement for cement. However, it is projected that in 2030 the demand for two of the most commonly used SCMs, fly ash and slag cement, will exceed their supply. Using nontraditional and natural pozzolans (NNPs) can help to close this supply gap, but there is a lack of knowledge regarding the reactivity and long-term performance of these materials.</p> <p>The purpose of this research was to perform experiments on several NNPs, some of which can be supplied in commercially viable quantities with the objective of evaluating their performance in cementitious systems (mortars and concretes) with the goal of accurately assessing their potential for use as alternative SCMs. The mortar study was performed using a total of 11 different NNPs, belonging to 4 distinctive groups and distributed as follows: 3 from the group of calcined clays (CCs) - CC1, CC2, and CC3, 3 from the group of natural pozzolans (NPs) - NP1, NP2 and NP3, 2 from the group of fluidized bed combustion (FBCs) ashes - FBC1 and FBC2, and 3 from the group of bottom ashes (GBAs) - GBA1, GBA2, and GBA3.</p> <p>The concrete study was performed on 4 different materials, one from each of the previously mentioned groups. The materials selected for concrete study were the worst-performing members of each group, as determined by the analysis of the test results obtained from mortars. These included CC2, NP3, FBC1, and GBA3 materials. This approach was adopted under the assumption that achieving adequate concrete characteristics with lowest-quality materials will all but assure satisfactory performance of concretes with higher-quality materials. </p> <p>The findings generated from this research indicate that several of the NNPs used in this study present a viable alternative to traditional SCMs. As an example, out of the 11 NNPS, 9 were found to conform to the requirements of the ASTM C618-19, the standard specification currently used to assess the suitability of coal fly ash and raw or calcined natural pozzolans for use in concrete. Results obtained from tests performed on mortars demonstrated that, when used at the replacement level of 25%, all 11 NNPs produced mixtures with characteristics similar to those obtained from the plain cement (OPC) mortar. For that reason, this level of replacement was selected to prepare concrete specimens. The results collected from concrete specimens showed that, when compared to plain concrete, mixtures with all 4 NNPs attained comparable (or improved) mechanical (compressive and flexural strength), durability (freeze-thaw resistance), and transport (formation factor and rate of water absorption) properties. As in the case of traditional SCMs, the mixtures with NNPs were found to require extended curing times to fully realize their property-enhancing potential associated with pozzolanic reactions. Overall, the best performing materials were those from the CCs group, followed by those belonging to, respectively, NPs, GBAs, and FBCs groups. </p>