The purpose of this research was to determine the effect of diameter fluctuations on the sensitivity of sapphire multimode optical fibers used as evanescent wave fluorescence sensors. It was predicted that fluctuations in the diameter of the fiber would act as a series of bi-tapers converting lower order modes to higher order modes increasing the evanescent wave penetration depth thereby increasing the excitation of a cladding of fluorescent fluid. Induced fluorescence from the fluid cladding would then couple back into the fiber more efficiently increasing the sensitivity of the sensor. The effect of coiling the fiber on the sensitivity of the sensor was also explored. Coiling the fiber converts lower order modes into higher order modes and increases the sensing length while maintaining a small probe size. However, coiling experiments produced unexpected results and in the course of studying these results a layer of material was discovered coating the surface of the sapphire fibers.

No description available.

No description available.

Optical fibers have been mostly used in fiber optic communications, imaging optics, sensing technology, etc. Fiber optic sensors have gained increasing attention for scientific and structural health monitoring (SHM) applications. In this study, fiber loop ringdown (FLRD) sensors were fabricated for scientific, SHM, and sensor networking applications. FLRD biosensors were fabricated for both bulk refractive index (RI)- and surface RI-based DNA sensing and one type of bacteria sensing. Furthermore, the effect of glucose oxidase (GOD) immobilization at the sensor head on sensor performance was evaluated for both glucose and synthetic urine solutions with glucose concentration between 0.1% and 10%. Detection sensitivities of the glucose sensors were achieved as low as 0.05%. For chemical sensing, heavy water, ranging from 97% to 10%, and several elemental solutions were monitored by using the FLRD chemical sensors. Bulk indexbased FLRD sensing showed that trace elements can be detected in deionized water. For physical sensing, water and cracking sensors were fabricated and embedded into concrete. A partially-etched single-mode fiber (SMF) was embedded into a concrete bar for water monitoring while a bare SMF without any treatment was directly embedded into another concrete bar for monitoring cracks. Furthermore, detection sensitivities of water and crack sensors were investigated as 10 ml water and 0.5 mm surface crack width, respectively Additionally fiber loop ringdowniber Bragg grating temperature sensors were developed in the laboratory; two sensor units for water, crack, and temperature sensing were deployed into a concrete cube in a US Department of Energy test bed (Miami, FL). Multi-sensor applications in a real concrete structure were accomplished by testing the six FLRD sensors. As a final stage, a sensor network was assembled by multiplexing two or three FLRD sensors in series and parallel. Additionally, two FLRD sensors were combined in series and parallel by using a 2×1 micro-electromechanical system optical switch to control sensors individually. For both configurations, contributions of each sensor to two or three coupled signals were simulated theoretically. Results show that numerous FLRD sensors can be connected in different configurations, and a sensor network can be built up for multiunction sensing applications.

No description available.

This PhD dissertation reports the development of miniature ion optics components of a mass spectrometer (MS) with the ultimate goal to lay the foundation for a compact low-power micromachined MS (µMS) for broad-range chemical analysis. Miniaturization of two specific components a) RF ion traps and b) an ion funnel have been investigated and miniature low-power versions of these components have been developed and demonstrated successfully in lab experiments. Power savings, simpler electronics and packaging schemes required to operate the micro-scale RF cylindrical ion traps have been the key motivation driving this research. Microfabricated cylindrical ion traps (µCITs) and arrays in silicon, silicon-on-insulator and stainless steel substrates have been demonstrated and average power of as low as 55 mW for a low mass range (28 to 136 amu) and mass spectra with better than a unit-mass-resolution have been recorded. For the ion funnel miniaturization effort, simple assembly, small form factor and ease of integration have been emphasized. A simplification of the conventional 3D ion funnel design, called the planar ion funnel, has been developed in a single plate and has been tested to demonstrate ion funneling at medium vacuum levels (1E-5 Torr) using DC voltages and power less than 0.5 W. Miniaturization of these components also enables use of other novel ion optics components, packaging and integration, which will allow a new class of µMS architectures amenable for radical miniaturization.

The large-scale abuse and addiction of narcotics such as amphetamine and cocaine have become a global problem. In this project, we innovatively use graphene quantum dots (GQDs) as a fluorescent sensor to detect and quantify amphetamine and cocaine. This technology will have broad forensic application prospects. Compared with metallic quantum dots, graphene quantum dots are green and safe, with excellent bio-compatibility and low toxicity. We used undoped and N-doped GQDs as fluorescent sensing probes for the detection of amphetamine and cocaine, respectively. Using FTIR and FL as characterization methods, the fluorescence luminescence of GQDs under multiple excitation wavelength bands was studied and compared with the fluorescence after adding drugs. The experimental results show that the N-doped GQDs has a higher response to the binding substance. The detection concentration of amphetamine ranges from 5 µM to 5 mM, and the detection concentration of cocaine ranges from 10 µM-10 mM. Within this range, the fluorescence peak intensity ratio and the drug concentration have a two-stage linear negative correlation. / Storskaligt missbruk och missbruk av narkotika som amfetamin och kokain har blivit ett globalt problem. I detta projekt använder vi innovativt grafenkvantprickar (GQDs) som en fluorescerande sensor för att detektera och kvantifiera amfetamin och kokain. Denna teknik kommer att ha breda rättsmedicinska applikationsmöjligheter. Jämfört med traditionella kvantprickar är grafenkvantprickar gröna och säkra, med utmärkt biokompatibilitet och låg toxicitet. Vi använde odopade och N-dopade GQD: er som fluorescerande avkännande sonder för detektion av amfetamin respektive kokain. Med användning av FTIR och FL som karakteriseringsmetoder studerades fluorescens luminiscens hos GQD under flera exciteringsvåglängdsband och jämfördes med fluorescensen efter tillsats av läkemedel. De experimentella resultaten visar att den N-dopade GQD har ett högre svar på den bindande substansen. Detekteringskoncentrationen av amfetamin sträcker sig från 5 µM till 5 mM, och detektionskoncentrationen av kokain varierar från 10 µM-10 mM. Inom detta område har fluorescens toppintensitetsförhållandet och läkemedelskoncentrationen en tvåstegs linjär negativ korrelation.

Magister Scientiae - MSc (Chemistry) / In this study, graphene oxide was synthesized by oxidizing graphite using the modified Hummer's method. The graphene oxide was characterized by Raman Spectroscopy, Fourier Transform Infrared Spectroscopy, High Resolution Transmission Electron Microscopy, Scanning Electron Microscopy and X-Ray Diffraction for structural and morphological properties. The graphene oxide was electrochemically reduced on a carbon paste electrode followed by the in situ deposition of mercury thin films to achieve electrochemically reduced graphene oxide modified carbon paste metal film electrodes (ERGO-CP-MEs). The experimental parameters (amplitude, deposition time, deposition potential, frequency and rotation speed) were optimized, and the applicability of the modified electrode was investigated towards the simultaneous and individual determination of TI1+ and In3+ at the low concentration levels (?g L-1) in 0.1 M acetate buffer (pH 4.6) using square wave anodic stripping voltammetry (SWASV). The detection limit values for individual analysis at electrochemically reduced graphene oxide modified carbon paste mercury film electrode (ERGO-CP-HgE ) was 2.4 and 1.1 ?g L-1 for TI1+ and In3+, respectively. The detection limit values for simultaneous analysis at ERGO-CPE was 1.32 and 1.33 ?g L-1 and individual analysis was 0.975 and 1.04 ?g L-1 for TI1+ and In3+, respectively.

Conductive polymer composite sensors have shown great potential in identifying gaseous analytes. To more thoroughly understand the physical and chemical mechanism of this type of sensors, a model was developed by combining two sub-models: a conductivity model and a thermodynamic model, which gives a relationship between the vapor concentration of analyte(s) and the change of the sensor signals. In this work, 64 chemiresistors representing eight different carbon concentrations (8–60 vol.% carbon) were constructed by depositing thin films of a carbon black–polyisobutylene composite onto concentric spiral platinum electrodes on a silicon chip. The responses of the sensors were measured in dry air and at various vapor pressures of toluene and trichloroethylene. Three parameters in the conductivity model were determined by fitting the experimental data. It was shown that by applying this model, the sensor responses can be predicted if the vapor pressure is known; furthermore the vapor concentration can be estimated based on the sensor responses. This model will guide the improvement of the design and fabrication of conductive polymer composite sensors for detecting and identifying organic vapors. A novel method was developed to optimize the selection of polymeric materials to be used within a chemiresistor array for anticipated samples without performing preliminary experiments. It is based on the theoretical predicted responses of chemiresistors and the criterion of minimizing the mean square error (MSE) of the chemiresistor array. After the number of chemiresistors to be used in an array and the anticipated sample chemistry are determined, the MSE values of all combinations of the candidate chemiresistors are calculated. The combination which has the minimum MSE value is the best choice. This can become computationally intensive for selection of polymers for large arrays from candidates in a large database. The number of combinations can be reduced by using the branch and bound method to save computation time. This method is suitable for samples at low concentrations where thermodynamic multi-component interactions are linear. To help users apply this polymer selection method for the sensors, a website including 10 solvents and 10 polymers was developed. Users can specify a target sample and obtain the best set of polymers for a sensor array to detect the sample. The activities of trichloroethylene and toluene in polyisobutylene were measured at very low concentrations. The activities for toluene are consistent with published values at higher concentrations. The values for trichloroethylene are a new contribution to the literature.

No description available.