Spelling suggestions: "subject:"collapse risk"" "subject:"ollapse risk""
1 |
Experimental and Numerical Study on the Extreme Behaviors of Sliding Isolation BearingsBao, Yu January 2017 (has links)
Sliding isolation bearings are used widely around the world to minimize damage to structures and their contents during earthquakes. Past studies have typically focused on the behavior of sliding isolation bearing under design conditions; however, as the performance-based earthquake engineering advances, it is necessary and critical to understand the ultimate or even failure behavior, of structural systems under extreme conditions. Using a double friction pendulum bearing with non-articulated slider as an example, this thesis comprehensively investigates the extreme behavior of the sliding bearing components as well as steel frame buildings isolated using these bearings.
This thesis is comprised of two major parts. The first includes numerical and experimental studies of double friction pendulum bearings at the component-level. Finite element investigation shows that depending on the superstructure mass there are two major failure modes for the double friction pendulum bearings. When the superstructure mass is sufficiently large, the failure mode is dominated by the restraining rim yielding; however, when the mass is relatively small, its failure mode shifts to bearing uplift. A simplified analytical model which can directly simulate the impact and uplift behavior of double friction pendulum bearing is also implemented, comparing well to the finite element analysis. Then, to validate the ability of the models to predict extreme behavior as well as to investigate the effect of the restraining rim design, which varies around the world, an experimental study was carried out. Uplift behavior and significant rim yielding were observed during the shake table tests. Moreover, other response parameters, including uplift and shear forces, are evaluated and compared among different rim designs. It is found the restraining rim design has a substantial influence on the bearing’s extreme behavior.
The second part of the thesis investigates the system-level behavior of steel frame buildings isolated with double friction pendulum bearings. It is found that the stiffness of the superstructure largely dictates the system-level failure modes and collapse probability. Initially, bearings with rigid restraining rims are investigated. For flexible moment-resisting frames, the system-level failure modes are mixed: both the bearing uplift and superstructure yielding contribute; also, using current code-minimum design results in acceptably low probability of collapse. However, for stiff concentrically-braced frames, the impact force can impose large ductility demands on the superstructure regardless of its strength. As a result, the system-level failure comes exclusively from superstructure yielding, and only by increasing bearing’s displacement capacity beyond the minimum code allowed can the design meet as acceptably low collapse probability. When flat rims are used instead for the bearing design, the failure modes for both building types are exclusively bearing failure. Furthermore, while it is more apparent for concentrically-braced frames, using flat rims for the bearings can reduce the collapse probability compared to using rigid rims. / Thesis / Doctor of Philosophy (PhD)
|
2 |
SYSTEM-LEVEL SEISMIC PERFORMANCE QUANTIFICATION OF REINFORCED MASONRY BUILDINGS WITH BOUNDARY ELEMENTSEzzeldin, Mohamed January 2017 (has links)
The traditional construction practice used in masonry buildings throughout the world is limited to walls with rectangular cross sections that, when reinforced with steel bars, typically accommodate only single-leg horizontal ties and a single layer of vertical reinforcement. This arrangement provides no confinement at the wall toes, and it may lead to instability in critical wall zones and significant structural damage during seismic events. Conversely, the development of a new building system, constructed with reinforced masonry (RM) walls with boundary elements, allows closed ties to be used as confinement reinforcement, thus minimizing such instability and its negative consequences. Relative to traditional walls, walls with boundary elements have enhanced performance because they enable the compression reinforcement to remain effective up to much larger displacement demands, resulting in a damage tolerant system and eventually, more resilient buildings under extreme events.
Research on the system-level (complete building) performance of RM walls with boundary elements is, at the time of publication of this dissertation, nonexistent in open literature. What little research has been published on this innovative building system has focused only on investigating the component-level performance of RM walls with boundary elements under lateral loads. To address this knowledge gap, the dissertation presents a comprehensive research program that covered: component-level performance simulation; system-level (complete building) experimental testing; seismic risk assessment tools; and simplified analytical models to facilitate adoption of the developed new building system. In addition, and in order to effectively mobilize the knowledge generated through the research program to stakeholders, the work has been directly related to building codes in Canada and the USA (NBCC and ASCE-7) as well as other standards including FEMA P695 (FEMA 2009) (Chapter 2), TMS 402 and CSA S304 (Chapter 3), FEMA P58 (FEMA 2012) (Chapter 4), and ASCE-41 (Chapter 5). Chapter 1 of the dissertation highlights its objectives, focus, scope and general organization. The simulation in Chapter 2 is focused on evaluating the component-level overstrength, period-based ductility, and seismic collapse margin ratios under the maximum considered earthquakes. Whereas previous studies have shown that traditional RM walls might not meet the collapse risk criteria established by FEMA P695, the analysis presented in this chapter clearly shows that RM shear walls with boundary elements not only meet the collapse risk criteria, but also exceed it with a significant margin. Following the component-level simulation presented in Chapter 2, Chapter 3 focused on presenting the results of a complete two-story asymmetrical RM shear wall building with boundary elements, experimentally tested under simulated seismic loading. This effort was aimed at demonstrating the discrepancies between the way engineers design buildings (as individual components) and the way these buildings actually behave as an integrated system, comprised of these components. In addition, to evaluate the enhanced resilience of the new building system, the tested building was designed to have the same lateral resistance as previously tested building with traditional RM shear walls, thus facilitating direct comparison. The experimental results yielded two valuable findings: 1) it clearly demonstrated the overall performance enhancements of the new building system in addition to its reduced reinforcement cost; and 2) it highlighted the drawbacks of the building acting as a system compared to a simple summation of its individual components. In this respect, although the slab diaphragm-wall coupling enhanced the building lateral capacity, this enhancement also meant that other unpredictable and undesirable failure modes could become the weaker links, and therefore dominate the performance of the building system. Presentation of these findings has attracted much attention of codes and standards committees (CSA S304 and TMS 402/ACI 530/ASCE 5) in Canada and the USA, as it resulted in a paradigm shift on how the next-generation of building codes (NBCC and ASCE-7) should be developed to address system-levels performance aspects. Chapter 4 introduced an innovative system-level risk assessment methodology by integrating the simulation and experimental test results of Chapters 2 and 3. In this respect, the experimentally validated simulations were used to generate new system-level fragility curves that provide a realistic assessment of the overall building risk under different levels of seismic hazard. Although, within the scope of this dissertation, the methodology has been applied only on buildings constructed with RM walls with boundary elements, the developed new methodology is expected to be adopted by stakeholders of other new and existing building systems and to be further implemented in standards based on the current FEMA P58 risk quantification approaches. Finally, and in order to translate the dissertation findings into tools that can be readily used by stakeholders to design more resilient buildings in the face of extreme events, simplified backbone and hysteretic models were developed in Chapter 5 to simulate the nonlinear response of RM shear wall buildings with different configurations. These models can be adapted to perform the nonlinear static and dynamic procedures that are specified in the ASCE-41 standards for both existing and new building systems. The research in this chapter is expected to have a major positive impact, not only in terms of providing more realistic model parameters for exiting building systems, but also through the introduction of analytical models for new more resilient building systems to be directly implemented in future editions of the ASCE-41. This dissertation presents a cohesive body of work that is expected to influence a real change in terms of how we think about, design, and construct buildings as complex systems comprised of individual components. The dissertation’s overarching hypothesis is that previous disasters have not only exposed the vulnerability of traditional building systems, but have also demonstrated the failure of the current component-by-component design approaches to produce resilient building systems and safer communities under extreme events. / Dissertation / Doctor of Philosophy (PhD)
|
3 |
Seismic Performance Evaluation of Industrial and Nuclear Reinforced Concrete Shear Walls: Hybrid Simulation Tests and Data-Driven ModelsAkl, Ahmed January 2024 (has links)
Low-aspect-ratio reinforced concrete (RC) shear walls, characterized by height-to-length ratios of less than two, have been widely used as a seismic force-resisting system (SFRS) in a wide array of structures, ranging from conventional buildings to critical infrastructure systems such as nuclear facilities. Despite their extensive applications, recent research has brought to light the inadequate understanding of their seismic performance, primarily attributed to the intricate nonlinear flexure-shear interaction behaviour unique to these walls. In this respect, the current research dissertation aims to bridge this knowledge gap by conducting a comprehensive evaluation to quantify the seismic performance of low-aspect-ratio RC shear walls when used in different applications.
Chapter 2 focuses on low-aspect-ratio RC shear walls that are employed in residential and industrial structures. Considering their significance, the seismic response modification factors of such walls, as defined in various standards, are thoroughly examined and evaluated utilizing the FEMA P695 methodology. The analysis revealed potential deficiencies in the current code-based recommendations for response modification factors. Consequently, a novel set of response modification factors, capable of mitigating the seismic risk of collapse under the maximum considered earthquake, is proposed. Such proposed values can be integrated into the forthcoming revisions of relevant building codes and design standards.
While the FEMA P695 methodology offers a comprehensive approach to assessing building seismic performance factors, its practical implementation is associated with many challenges for practicing engineers. Specifically, the methodology heavily relies on resource-intensive and time-consuming incremental dynamic analyses, making it less feasible for routine engineering practices. To enhance its practicality, a data-driven framework is developed in Chapter 3, circumventing the need for such demanding analyses. This framework provides genetic programming-based expressions capable of producing accurate predictions of the median collapse intensities—a key metric in the acceptance criteria of the FEMA P695 methodology, for different structural systems. To demonstrate its use, the developed framework is operationalized to low-aspect-ratio RC shear walls and the predictive expression is evaluated considering several statistical and structural parameters, which showed its adequacy in predicting the median collapse intensities of such walls. Furthermore, the adaptability of this framework is showcased, highlighting its applicability across various SFRSs.
Chapters 4 and 5 tackle the scarcity of experimental assessments pertaining to the seismic performance of low-aspect-ratio RC walls in nuclear facilities. The seismic hybrid simulation testing technique is employed herein to merge the simplicity of numerical simulations with the efficiency of experimental tests. Hybrid simulation can overcome obstacles related to physical specimen sizes, limited actuator capacities, and space constraints in most laboratories. In these two chapters, the experimental program delves into evaluating the seismic performance of three two-storey low-aspect-ratio nuclear RC walls under different earthquake levels, including operational, design, and beyond-design-level scenarios. Diverse design configurations, including the use of increased thickness boundary elements and different materials (i.e., normal- and high-strength reinforcement), are considered in such walls to provide a comprehensive understanding of several structural parameters and economic metrics. Key structural parameters, such as the force-displacement responses, multi-storey effects, lateral and rotational stiffnesses, ductility capacities, displacement components, rebar strains, crack patterns and damage sequences, are all investigated to provide direct comparisons between the walls in terms of their seismic performances. Additionally, economic metrics, including the total rebar weights, overall construction costs and the expected seismic repair costs, are considered in order to evaluate the seismic performance of the walls considering an economic perspective. The findings of this experimental investigation are expected to inform future nuclear design standards by enhancing the resilience and safety of their structures incorporating low-aspect-ratio RC shear walls. / Thesis / Doctor of Philosophy (PhD)
|
Page generated in 0.0464 seconds