Objectives: To determine if temporomandibular joint (TMJ) compressive stresses during incisor biting (1) differed between growing children over time, and (2) were correlated with Frankfort Horizontal-mandibular plane angle (FHMPA, 8) and ramus length (Condylion-Gonion (Co-Go), mm). Materials and Methods: Three-dimensional anatomical geometries, FHMPA and Co-Go, were measured longitudinally from lateral and posteroanterior cephalographs1 of children aged 6 (T1), 12 (T2), and 18 (T3) years. Geometries were used in numerical models to estimate subject-specific TMJ eminence shape and forces for incisor bite-forces of 3, 5, and 8 Newtons at T1, T2, and T3, respectively. TMJ compressive stresses were estimated via two steps: First, TMJ force divided by age-dependent mandibular condylar dimensions, and second, modified by loading surfaces' congruency. Analysis of variance and Tukey honest significant difference post-hoc tests, plus repeated measures and mixed effects model analyses were used to evaluate differences in variables between facial groups. Regression analyses tested for correlation between agedependent compressive stresses, FHMPA, and Co-Go. Results: Sixty-five of 842 potential subjects had T1-T3 cephalographs and were grouped by FHMPA at T3. Dolichofacial (FHMPA ≥ 27°, n=36) compared to meso-brachyfacial (FHMPA, 27°, n=29) subjects had significantly larger FHMPA at T1-T3, shorter Co-Go at T2 and T3 (all P < .01), and larger increases in TMJ compressive stresses with age (P < .0001). Higher compressive stresses were correlated with larger FHMPA (all R2 ≥ 0.41) and shorter Co-Go (all R2 ≥ 0.49). Conclusions: Estimated TMJ compressive stress increases from ages 6 to 18 years were significantly larger in dolichofacial compared to meso-brachyfacial subjects and correlated to FHMPA and Co-Go.

The pervious concrete system and its corresponding strength are as important as its permeability characteristics. The strength of the system not only relies on the compressive strength of the pervious concrete but also on the strength of the soil beneath it for support. Previous studies indicate that pervious concrete has lower compressive strength capabilities than conventional concrete and will only support light traffic loadings. This thesis investigated prior studies on the compressive strength on pervious concrete as it relates to water-cement ratio, aggregate-cement ratio, aggregate size, and compaction and compare those results with results obtained in laboratory experiments conducted on samples of pervious concrete cylinders created for this purpose. The loadings and types of vehicles these systems can withstand will also be examined as well as the design of appropriate thickness levels for the pavement. Since voids are supposed to reduce the strength of concrete 1% for every 5% voids(Klieger, 2003), the goal is to find a balance between water, aggregate, and cement in order to increase strength and permeability, two characteristics which tend to counteract one another. In this study, also determined are appropriate traffic loads and volumes so that the pervious concrete is able to maintain its structural integrity. The end result of this research will be a recommendation as to the water-cement ratio, the aggregate-cement ratio, aggregate size, and compaction necessary to maximize compressive strength without having detrimental effects on the permeability of the pervious concrete system. This research confirms that pervious concrete does in fact provide a lower compressive strength than that of conventional concrete; compressive strengths in acceptable mixtures only reached 1700 psi. Extremely high permeability rates were achieved in most all mixtures regardless of the compressive strength. Analysis of traffic loadings reinforce the fact that pervious concrete cannot be subjected to large numbers of heavy vehicle loadings over time although pervious concrete would be able to sustain low volumes of heavy loads if designed properly. Calculations of pavement thickness levels indicate these levels are dependent on the compressive strength of the concrete, the quality of the subgrade beneath the pavement, as well as vehicle volumes and loadings.

Yes / This paper examines the impacts of clay mineralogy on the effectiveness of lime stabilisation at different temperatures. A comprehensive experimental programme was conducted to track down the evolution of lime-clay reactions and their durations through monitoring the evolution of strength gain at predetermined times using the Unconfined Compressive Strength (UCS) test. The study examined clays with different mineralogy compositions comprising Na+ Bentonite and Ball (Kaolinite) clay. Four different clays were tested including 100% bentonite, 100% Ball clay and two clay mixtures with ratios of 1:1 and 1:3 by mass of bentonite to Ball clay. All clays were treated using a range of lime content up to 25% and cured for a period of time up to 672 h at two different temperatures of 20 and 40 °C. The results showed that the continuity of the fast phase (stage 1) of strength gain was dependent on the availability of lime in particular at the higher temperature. Whereas, for the same lime content, the duration of the fast phase and the kinetic of strength gain were significantly related to the clay mineralogy and curing temperature. Except for the initial strength gain at 0 h curing time, the lime-treated Ball clay specimens at 20 °C appeared to show no strength gain throughout the curing period that extended up to 672 h. However, when curing occurred at 40 °C, the no strength gain stage only lasted for 72 h after which a gradual increase in the strength was observed over the remaining curing period of time. The addition of Bentonite to Ball clay succeeded in kicking off the strength gain after a short period of curing time at both curing temperatures.

Yes / In this study, the main emphasis is placed on the development and characterization of alkali-activated binders completely produced by the use of mixed construction and demolition waste (CDW)-based masonry units as aluminosilicate precursors. Combined usage of precursors was aimed to better simulate the real-life cases since in the incident of construction and demolition, these wastes are anticipated to be generated collectively. As different masonry units, red clay brick (RCB), hollow brick (HB) and roof tile (RT) were used in binary combinations by 75-25%, 50-50% and 25-75% of the total weight of the binder. Mixtures were produced with different curing temperature/periods and molarities of NaOH solution as the alkaline activator. Characterization was made by the compressive strength measurements supported by microstructural investigations which included the analyses of X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM/EDX). Results clearly showed that completely CDW-based masonry units can be effectively used collectively in producing alkali-activated binders having up to 80 MPa compressive strength provided that the mixture design parameters are optimized. Among different precursors utilized, HB seems to contribute more to the compressive strength. Irrespective of their composition, main reaction products of alkali-activated binders from CDW-based masonry units are sodium aluminosilicate hydrate (N-A-S-H) gels containing different zeolitic polytypes with structure ranging from amorphous to polycrystalline.

Yes / As a viable option to upcycle construction and demolition waste (CDW) into value-added materials, geopolymer technology is emerging. Most studies investigate CDWs in a separated form or in combination with mainstream pozzolanic/cementitious materials focusing only on fundamental properties of geopolymer pastes, not considering to scale such materials to the level of their application in the forms of structural mortars/concretes or to characterize long-term performance/durability. This study investigated the development and characterization of ambient-cured mortars with mixed CDW-based geopolymer binders and untreated fine recycled concrete aggregates (FRCA). Mixture of CDW-based roof tile (RT), red clay brick (RCB), hollow brick (HB), concrete (C), and glass (G) was used as the precursor, while ground granulated blast furnace slag (S) was used in some mixtures to partly replace CDW precursors. Compressive strength, durability-related parameters including drying shrinkage, water absorption, and efflorescence, microstructure and materials sustainability were evaluated. Results showed that 28 d compressive strength results above 30 and 50 MPa is achievable with the entirely CDW-based and slag-substituted mortars, which were found improvable to have entirely CDW-based structural concretes. Drying shrinkage of the mortars is slightly higher than that of conventional cementitious/geopolymeric systems although it can be minimized significantly through mixture optimization. Water absorption values remain comparable with the literature. CDW-based geopolymer mortars outperform Portland cement mortars in terms of CO2 emission and energy requirement. Our findings show that via utilizing CDW-based constituents in mixed form as precursor and waste aggregates, it is possible to develop greener construction materials with acceptable strength and long-term performance. / This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 894100. The authors also wish to acknowledge the support of the Scientific and Technical Research Council (TUBITAK) of Turkey provided under project: 117M447.

Yes / This paper aims to evaluate the influence of surface area and amount of nano silica (NS) on the performance of concrete with different water/binder (w/b) ratios. For this purpose, 63 different mixes were produced using three NS having three differentsurface areas (52, 250 and 500 m2/g) and w/b ratios (0.4, 0.5 and 0.6). Compressive strengths , workability, water absorption and the microstrcture of concrete mixtures were measured and analysed. and the optimum ratio for each type was determined. The results indicated that the performance of NS particles in concrete is significantly dependent on its amount and surface area as well as w/b ratio. As the w/b ratio increased, a better performance was observed for all types of NS used, whilst NS having 250m2/g surface area was found to be the most effective. The optimum amount of NS ranged from 2 to 5%, depending on NS surface area. / The full-text of this article will be released for public view at the end of the publisher embargo on 15 May 2020.

No description available.

Cemented paste backfill (CPB) technology is widely used in the mining industry as an effective means of tailings disposal. CPB is a mixture of tailings, binder, water, and additional admixtures when required. It is prepared in a mixing plant on the ground surface and then transported into the mine cavities through pipelines either by gravity and/or using pumps. To ensure efficiency during transportation and avoid pipe clogging (which can cause unnecessary delays and loss of productivity), fresh CPB must have sufficient flowability. To achieve that, high-range water reducing admixtures, also known as superplasticizers, are usually added to the CPB during mixing. These admixtures are widely used in the construction industry due to their ability to improve flowability without undermining other important engineering properties. However, their influence on the rheology, mechanical strength and environmental performance (reactivity and permeability) of CPB is not fully understood. Thus, experimental studies were conducted to investigate the effects of superplasticizers on the performance properties of cemented paste backfill at different curing temperatures. Yield stress and viscosity of fresh CPB cured for 0, 1, 2, and 4 hours were measured using a vane shear device and a Brookfield Viscometer respectively. Unconfined compressive strength (UCS) of samples cured for 1, 3, 7, and 28 days was determined in accordance with ASTM - C39. Superplasticizer contents were varied as 0%, 0.125%, and 0.25% of the total weight of the CPB. Preparations and curing of the specimens were performed at controlled conditions of 2, 20, and 35 °C to investigate the effect of ambient or curing temperatures. To have a better understanding of the environmental performance of CPB containing superplasticizer, reactivity, and hydraulic conductivity up to 90 days of curing were also investigated. The reactivity was measured using oxygen consumption test while hydraulic conductivity was measured using flexible wall permeability test. Microstructural analyses (thermogravimetric analyses, X-Ray diffraction, and mercury intrusion porosimetry) and monitoring tests (pH, zeta potential, electrical conductivity, and matric suction) were carried out to understand the principles behind the changes of the observed properties. The obtained results show that superplasticizer dosage and temperature variation have significant effects on the rheology, strength development, hydraulic conductivity and reactivity of the CPB. The polycarboxylic ether-based superplasticizer significantly reduces the yield stress and viscosity by creating strong electrostatic repulsion between the solid particles in the CPB and by steric hinderance. The CPB containing the superplasticizer remains fluid for longer period (as compared with the CPB without superplasticizer) due to the retardation of binder hydration. However, high curing temperature induces faster cement hydration, which thickens the fresh CPB. The unconfined compressive strength (UCS) of the CPB containing superplasticizer was observed to be lower in the early age (up to 7 days), which is also attributed to retardation of the binder hydration. At later ages, the superplasticizer improves the mechanical strength as the binder hydration accelerates and the solid particles self-consolidate. Coupled THMC processes in the CPB showed the role played by the changes in electrical conductivity, volumetric water content, matric suction, and temperature on the development of mechanical strength of the CPB containing superplasticizer. Similarly, addition of the superplasticizer in the CPB decreases both the hydraulic conductivity and reactivity of CPB, thus improving its environmental performance. The improvement is largely attributed to enhanced binder hydration and self-consolidation which decrease the porosity of the CPB. Increasing the curing temperature was found to magnify the improvement of the CPB properties by inducing faster binder hydration. The findings from this study will undoubtedly inform the design of CPB structure with better mechanical stability and environmental performance.

High frame rate video (HFV) is an important investigational tool in sciences, engineering and military. In ultrahigh speed imaging, the obtainable temporal, spatial and spectral resolutions are limited by the sustainable throughput of in-camera mass memory, the lower bound of exposure time, and illumination conditions. In order to break these bottlenecks, we propose a new coded video acquisition framework that employs K>1 cameras, each of which makes random measurements of the video signal in both temporal and spatial domains. For each of the K cameras, this multi-camera strategy greatly relaxes the stringent requirements in memory speed, shutter speed, and illumination strength. The recovery of HFV from these random measurements is posed and solved as a large scale l1 minimization problem by exploiting joint temporal and spatial sparsities of the 3D signal. Three coded video acquisition techniques of varied trade o s between performance and hardware complexity are developed: frame-wise coded acquisition, pixel-wise coded acquisition, and column-row-wise coded acquisition. The performances of these techniques are analyzed in relation to the sparsity of the underlying video signal. To make ultra high speed cameras of coded exposure more practical and a fordable, we develop a coded exposure video/image acquisition system by an innovative assembling of multiple rolling shutter cameras. Each of the constituent rolling shutter cameras adopts a random pixel read-out mechanism by simply changing the read out order of pixel rows from sequential to random. Simulations of these new image/video coded acquisition techniques are carried out and experimental results are reported. / Dissertation / Doctor of Philosophy (PhD)

In recent years, repetitive traumatic brain injuries have been linked to the progressive neurodegenerative disorder termed chronic traumatic encephalopathy. However, the mechanical characteristics of brain tissue exposed to repetitive loading still lack understanding. This research evaluated the response of porcine brain tissue undergoing cyclic, compressive loading in reference to three impact parameters: cycle number (N25, N50, N100, N150, and N200), strain level (15, 30, and 40%), and strain rate (0.00625, 0.025, 0.10, and 1.0/s). Following mechanical testing, tissue samples were processed for hematoxylin and eosin (H&E) staining. Stress values, hysteresis energy, and decreases in hysteresis energy for all parameters were compared. The data suggest that microstructural brain tissue damage is highly dependent on strain level and cycle number, whereas strain rate did not appear to cause permanent damage in the quasi-static range applied. The onset of permanent microstructural tissue damage may relate to movement of fluid molecules within the tissue.