This work investigates the Fresnel-lens-based solar concentrator-receiver system in a multi-perspective manner to design, test and fabricate this concentrator with high-efficiency photon and heat outputs and a minimized effect of chromatic aberrations. First, a MATLAB®-incorporated algorithm optimizes both the flat-spot and the curved lens designs via a statistical ray-tracing methodology of the incident light, considering all of its incidence parameters. The target is to maximize the solar ray intensity on the receiver's aperture, and therefore, achieve the highest possible focal flux. The algorithm outputs prismatic and dimensional geometries of the Fresnel-lens concentrator, which are simulated by COMSOL® Multiphysics to validate the design. For the second part, a novel genetically-themed hierarchical algorithm (GTHA) has been investigated to design Fresnel-lens solar concentrators that match with the distinct energy input and spatial geometry of various thermal applications. Basic heat transfer analysis of each application decides its solar energy requirement. The GTHA incorporated in MATLAB® optimizes the concentrator characteristics to secure this energy demand, balancing a minimized geometry and a maximized efficiency. Two experimental applications were selected from literature to validate the optimization process, a solar welding system for H13 steel plates and a solar Stirling engine with an aluminum-cavity receiver attached to the heater section. In each case, a flat Fresnel-lens with a spot focus was algorithmically designed to supply the desired solar heat, and then a computer simulation of the optimized lens was conducted showing great comparability to the original experimental results. Thirdly, the prismatic geometry of the Fresnel lens was further optimized through a statistical approach that incorporates laws of light refraction and trigonometry. The proposed design produces high focal irradiance that is more suitable for thermal applications. The motivation was to enhance the tolerability of a flat Fresnel-lens concentrator to tracking errors, without the use of secondary optics or sophisticated, and normally costly, meticulous tracking equipment. A comparative simulation analysis was conducted for two case studies from literature, each with a different design method. Fresnel lenses optimized by this work enhanced the concentration acceptance product (CAP) significantly, compared to that in literature. Then, this work introduced an innovative code-based, detailed, and deterministic geometrical approach, which couples the optimization of the Fresnel lens primary optical element (POE) and the dome-shaped secondary optical element (SOE). The objective was to maximize the concentration acceptance product, while using the minimum SOE and receiver geometries at a given f-number and incidence angle (also referred to as the tracking error angle). The laws of polychromatic light refraction along with trigonometry and spherical geometry were utilized to optimize the POE grooves, SOE radius, receiver size, and SOE–receiver spacing. Two literature case studies were analyzed to verify this work's optimization, and the equivalent POEs designed by this work, with optimized SOEs, showed a significant enhancement in the CAP values compared to that of literature. Lastly, four methods for prototyping the Fresnel lens were discussed and experimentally tested; 3D printing, acrylic resin casting, direct CNC machining in acrylic and hot embossing. Once tested, the methods of CNC machining and hot embossing of acrylic proved to be the most promising in terms of cost, fabrication time, and concentration effectiveness. Future work will focus on enhancing the algorithmic design and improving the quality of lens fabrication.

The goal is to design data concentrator for Smart Grids. Data Concentrator provides the interface between the server systems of distribution companies and end devices, which are electricity meters, water meters, gas meters and other equipment. There are hardware and software design solutions and there is also discussed creating its own distribution of Linux.

Switch Optimization in a Converged Network thesis discusses the role of the Ethernet switch in the network. It describes differences between the switch and the hub in the network and the impacts on the collision domain size. In the converged network, priority data switching according to their origin and thus the qualitative point of view is also addressed - e-mails, voice services and multimedia will each behave differently. A real element, switch L3 - a switch with services quality support - is mentioned. The tool Matlab - Simulink is briefly described and a functional simplified model of the ethernet switch was created. Furthermore, the topic was used as a theme for a laboratory task in the subject Services of Telecommunication Networks. A model for Simulink and an example of the laboratory protocol for the created task are attached to the thesis.

The master thesis is focused on estimation of crack propagation origin from sharp V-notch. Stress distribution around the tip of the V-notch is described on the base of generalized linear elastic fracture mechanics. The change of the stress singularity exponent caused by geometry of the V-notch and the vertex singularity is taken into account. The first part of the work is devoted to the estimation of the stress singularity exponent of the V-notch either from stress distribution around the tip of the V-notch or by using analytical solution. Formerly derived stability criteria are applied in the second part of the work. The origin of the crack propagation is estimated for several experimental specimens. The aim of this thesis is to compare the available experimentally observed data with results obtained using those criteria based on the application of generalized linear elastic fracture mechanics developer at the Institute of Physics of Materials Academy of Sciences of the Czech Republic. The finite element code Ansys and mathematical software Matlab were used for the necessary calculations.

Depuis les années quarante, la consommation énergétique mondiale n'a cessé d'augmenter. Cette énergie étant majoritairement d'origine fossile, il en résulte une augmentation globale de température terrestre. De ce fait, il est devenu urgent de réduire les émissions de gaz à effet de serre pour stopper le changement climatique. Dans ce contexte, le développement de la production d'électricité à partir d'énergie solaire concentrée par voie thermodynamique est une solution prometteuse. Les efforts de recherche visent à rendre cette technologie plus efficace et plus compétitive économiquement. Dans ce but, ce manuscrit présente une méthode de conception optimale pour les centrales solaires à récepteur central. Elle tire parti des méthodes développées depuis de nombreuses années par le groupe de recherche StaRWest, regroupant notamment des chercheurs des laboratoires RAPSODEE (Albi), LAPLACE (Toulouse) et PROMES (Odeillo). Couplant des algorithmes de Monte Carlo à hautes performances et des algorithmes stochastiques d'optimisation, le code de calcul implémentant cette méthode permet la conception et l'optimisation d'installations solaires. Il est utilisé pour mettre en évidence les potentialités d'un type de centrales à récepteur central peu répandu : les centrales à réflecteur secondaire, également appelées centrales de type "beam down". / Since the early 40's, world energy consumption has grown steadly. While this energy mainly came from fossil fuel, its use has included an increase in temperatures. It has become urgent to reduce greenhouse gas emissions to halt climate change. In this context, the development of concentrated solar power (CSP) is a promising solution. The scientific community related to this topic has to focus on efficiency enhancement and economic competitiveness of CSP technologies. To this end, this thesis aims at providing an optimal design method applied to central receiver power plants. It takes advantage of methods developed over many years by the research group StaRWest. Both RAPSODEE (Albi), LAPLACE (Toulouse) and PROMES (Odeillo) researchers take an active part in this group. Coupling high performance Monte Carlo algorithms and stochastic optimization methods, the code we developed allows an optimal design of concentrated solar systems. This code is used to highlight the potential of an uncommon type of central receiver plants: reflective towers, also called "beam down" central receiver systems.

Depuis le début des années 2000, les performances des LED ne cessent de s'améliorer et permettent l'ancrage de cette technologie dans de nombreux domaines d'applications. Stimulées par le marché de l'éclairage, les LED présentent une longue durée de vie et une grande robustesse pour un prix par watt optique défiant toute concurrence. Pour améliorer leur luminance, les LED peuvent être couplées à des concentrateurs luminescents.La première partie de cette thèse expose la mise au point des premiers concentrateurs luminescents dans SWIR (gamme 1,2-2,5 µm où les LED sont peu efficaces). Nous montrons que la luminance des concentrateurs luminescents dans le SWIR dépasse celle des LED d'un ordre de grandeur. Elle rend possible la détection de l'eau dans l'industrie agroalimentaire ainsi que l'inspection de wafers de silicium. Dans le visible, les performances des concentrateurs luminescents (luminance, spectre, prix, régime de fonctionnement) offrent une combinaison unique des avantages des lampes flash et des diodes laser. La seconde partie de cette thèse explore la possibilité d'utiliser ces concentrateurs luminescents pour pomper des lasers solides. Cette étude démontre la compatibilité de ce nouveau type de pompage avec les cristaux dopés aux métaux de transition, incontournables dans le domaine des lasers ultra-courts. Pour la première fois, un effet laser en régime relaxé est obtenu via le pompage par LED du Cr:LiSGaF, du Cr:LiSAF, de l’alexandrite, et du Ti:saphir. Ces premières démonstrations ouvrent la voie à des systèmes laser basés sur le pompage par LED. Plusieurs systèmes sont mis en place tels que des oscillateurs lasers en régime déclenché (Q-switch et cavity-dump) faisant l'objet de conversions de fréquence, et des amplificateurs d'impulsions laser. / Since the beginning of the 2000s, LED's performance have known dramatic improvements which enable this technology to settle down in numerous application areas. Driven by the lighting market, LED are characterized by their long lifetime, their ruggedness, and their low cost per emitted optical watt. In order to go beyond LED's brightness, they can be coupled to luminescent concentrators.The first part of this work exposes the development of the first luminescent concentrator in the short-wave infrared (or SWIR corresponding to the 1.2-2.5 µm band where LED have very low powers). This work shows that the brightness of the luminescent concentrators in the SWIR exceeds by one order of magnitude LED's brightness in the same spectral range. This light source allows water detection for the agrifood industry and the inspection of silicon wafers for microelectronics. In the visible, the performance of luminescent concentrators (brightness, spectrum, price, mode of operation) offer a unique trade-off between flashlamps and laser diodes. The second part of this work investigates the use luminescent concentrators emitting in the visible to pump solid-state lasers. The compatibility of this new pumping concept is attested with transition-metals-doped crystals, cornerstone of ultrafast laser sources. For the first time, laser oscillations in free-running operation are obtained by LED-pumping of Cr:LiSGAF, Cr:LiSAF, alexandrite and Ti:sapphire. These early results open the way to LED-pumped laser systems. Several systems are implemented such as laser oscillators in pulsed operation (Q-switch and cavity dump) followed by frequency conversions and laser pulses amplifiers.

This project is a bachelor thesis and aims to study the integration of concentrator photovoltaics (CPV), reverse osmosis (RO) and membrane distillation (MD) for water desalination and purification. In this report, an introduction of the need for efficient water desalination is presented. Following the introduction, relevant literature has been reviewed to build up the fundamental understanding of CPV, RO and MD. A general classification of CPV subsequently introduced. In order to acquire a more comprehensive understanding of CPVs, two case studies were performed with two different types of CPV/T. The cost efficiency of each type of CPV was analysed when integrated with RO and MD systems. The result turns out to be that it was not economically beneficial to have MD in the integrated system. The reason behind is the extensive thermal energy demand of MD. Other affecting parameters, such as location and system types were also discussed. Lastly, improvements and suggestions for further studies were considered. / Detta projekt är en kandidatuppsats och syftar till att studera ett integrerande system bestående av koncentrerade solceller (CPV), omvänd osmos (RO) och membrandestillation (MD) för vattenavsaltning och rening. Rapporten börjar med en introduktion om behovet av effektiv avsaltning av vatten. Relevant litteratur har granskats för att bygga upp den grundläggande förståelsen för CPV, RO och MD. Därefter gjordes en klassificering av CPV. För att få en mer omfattande förståelse av CPV valdes två olika typer av CPV /T för en djupare undersökning. Kostnadseffektiviteten för varje CPV analyserades, när dessa var integrerade med RO- och MD-system. Resultatet visar sig att det tyvärr inte var ekonomiskt fördelaktigt att ha med MD i det integrerade systemet. Anledningen bakom detta var det omfattande termiska energibehovet för MD. Andra avgörande faktorer, såsom plats och systemtyp diskuterades tillika. Slutligen avslutades rapporten med förslag på förbättringar och områden för vidare studier.

Research on salts species formed by evaporation of aqueous solution of Na2 in the early 1930s. The thermodynamic, crystallographic and many other physical and chemical properties of most of the species formed from this solution has been known for decades. However, there was no complete information or reliable data to confirm the existence of a unique double salt that is rich in sodium carbonate, up until five years ago when a research identified the double salt (~2Na ₂ CO ₃ • Na ₂ SO ₄) from the ternary system Na₂CO ₃Na₂SO ₄ H₂O. Crystallization of this double salt so called sodium sulfate dicarbonate (~2Na ₂ CO ₃ • Na ₂ SO ₄) is known to be a primary contributor to fouling heat transfer equipment in spent-liquor concentrators used in the pulp and paper industry. Therefore, understanding the conditions leading to formation of this double salt is crucial to the elimination or reduction of an industrial scaling problem. In this work, double salts were generated in a batch crystallizer at close to industrial process conditions. X-ray diffraction, calorimetry, and microscopic observation were used to investigate the stability of the salts to in-process aging, isolation and storage, and exposure to high temperature. The results show that care must be taken during sampling on evaporative crystallization. Two apparent crystal habits were detected in the formation of sodium sulfate dicarbonate; the favored habit may be determined by calcium ion impurities in the system. The results also verify that sodium sulfate dicarbonate exists as a unique phase in this system and that remains stable at process conditions of 115-200℃

Geometrical discontinuities, like sharp notches, appear in constructions and engineering structures and lead to stress concentrations. These technical objects are very dangerous due to the fact that they reduce the structural conformity and can lead to crack initiation. Technical objects are not always designed as homogenous bodies but can consist of two or more materials with sharp notches on the interface of these materials. The influence of free surface on crack initiation conditions is studied and assessed by means of 3D model of sharp and bi-material notches with finite thickness. Stress fields around the singular stress concentrators are calculated with finite element method and the results are evaluated by means of criterion of critical quantity. This approach is easy applicable and can be used in combination with the knowledge of basic material properties and results of finite element analysis of the assessed notches. In order to estimate weather crack will initiate from the middle of the observed notched specimen or from its free surface, the value of averaged critical applied stress was introduced. With this value it’s possible to determine the location of crack initiation thru the sample thickness. Thru the ratio of values of critical applied stress in the middle and on the free surface of the observed specimen it’s possible to quantify the influence of the free surface on the location of crack initiation. With the use of this approach it’s shown, that the location of crack initiation depends on more parameters, loading direction, the notch opening angle and the sample thickness. In case of bi-material notches it depends also on the ratio of young modulus.

El concentrador solar Fixed Mirror Solar Concentrator (FMSC) apareció en los años 70 con la finalidad de reducir costes en la producción de energía termoeléctrica. Este diseño consiste en un concentrador de reflector estacionario y foco móvil, presenta buena integrabilidad en cubiertas, y es capaz de alcanzar temperaturas entre 100 y 200ºC manteniendo una eficiencia aceptable. En esta tesis se expone una metodología para determinar el comportamiento del FMSC. Se ha desarrollado una herramienta de cálculo basada en el método de ray-tracing, que simula el trazado de los rayos solares en el sistema óptico. Con esta herramienta se ha analizado el comportamiento óptico y térmico del FMSC, y de la versión con espejos curvos Curved Slats Fixed Mirror Solar Concentrator (CSFMSC). Se ha realizado un análisis paramétrico para conocer la influencia de los distintos parámetros en el modificador de ángulo (IAM), y para obtener los diseños óptimos a una temperatura de 200ºC para tres climas en diferentes latitudes. Se han comparado los valores teóricos obtenidos mediante ray-tracing con dos prototipos ensayados, obteniendo un buen ajuste en ambos casos. Los ensayos han sido utilizados para determinar la curva de rendimiento de uno de los prototipos. Se ha hecho uso del método propuesto en la norma EN-12975-2:2006, combinado con valores de IAM obtenidos mediante ray-tracing. Se prueba que esta combinación puede ser útil para obtener la curva de rendimiento de colectores complejos con un modelo biaxial para el IAM. / The Fixed Mirror Solar Concentrator (FMSC) appeared during the 70s with the aim of reducing costs in the production of electricity in solar thermal power plants. This design consists of a concentrator with fixed reflector and moving receiver, has a very good integrability into building roofs and can reach temperatures between 100 and 200ºC with an acceptable efficiency. In this Thesis a methodology is presented for the determination of the behaviour of the FMSC. A simulation tool based on the forward ray-tracing method has been developed. The optical and thermal behaviour of the FMSC and its curved mirror variation called the Curved Slats Fixed Mirror Solar Concentrator (CSFMSC), have been analyzed with this tool. A parametric analysis has been carried out in order to determine the influence of the different parameters on the Incidence Angle Modifier (IAM) and to determine the optimal designs at a temperature of 200ºC for three different climates at different latitudes. The theoretical values obtained from the ray-tracing code have been compared with two experimental prototypes. The experimental and numerical results obtained show a good fit. The efficiency curve of one of the prototypes has been determined from the experimental tests. The methodology proposed in the norm EN-12975-2:2006 has been used in combination with IAM values obtained by ray-tracing. It has been shown that this combination can be effectively used to obtain the efficiency curve of complex collectors with a bi-axial IAM model.