[pt] Este trabalho apresenta uma análise experimental de cinco vigas de concreto, simplesmente apoiadas, protendidas com cabos sintéticos externos, com o objetivo de estudar a influência da resistência do concreto na variação da força nos cabos de protensão e na resistência à flexão das vigas. A protensão das vigas foi feita com cabos sintéticos conhecidos como Parafil, com resistência a tração de 1950MPa e módulo de elasticidade de 126000MPa. A única variável considerada foi a resistência do concreto, cujo valores foram 36, 57, 73, 74 e 104MPa. O concreto das vigas com resistência de 57, 73, 74 e 104MPa foram feitos com o uso da microssílica e aditivo superplastificante, com exceção da viga com resistência de 36MPa que foi feita com concreto comum. Os resultados mostraram que a influência da resistência do concreto sobre a resistência à flexão das vigas não é tão grande. Para o aumento de 189% na resistência do concreto, houve um aumento na variação da força no cabo de apenas 13.6% e um aumento de 33% no momento de ruptura. Na comparação dos resultados experimentais com os resultados das principais normas e modelos propostos verificou-se que todos fornecem bons resultados e subestimam os valores experimentais. Na comparação dos resultados experimentais com o modelo de Campos (1993) observou-se que os valores da variação na força no cabo superestimam os valores experimentais. / [en] An experimental investigation on five concrete beams prestressed with external aramid tendons was carried out for the purpose of studying the influence of concrete on the flexural behaviour at service and ultimate loads. The beams were prestressed with Type G Parafil tendons, which are made of Kevlar 49 fibres. The strength and elastic modulus of the cables are 1950 MPa and 12600 MPa respectively. The main variable considered in the testes was the strength of the concrete with values of 36, 57, 73, 74 and 104 MPa. The results show that for an increase of 189% in the strength of the concrete, an increase of only 33% in the ultimate moment is observed. Experimental results were compared with results predicted by some Codes of Practice. This comparison shows that the theoretical models give good results. / [es] Este trabajo presenta un análisis experimental de cinco vigas de concreto, simplemente apoyadas, protendidas con cables sintéticos externos, con el objetivo de estudiar la influencia de la resistencia del concreto en la variación de la fuerza de los cables de protensión y en la resistencia a la flexión de las vigas. La protensión de las vigas fue hecha con cables sintéticos conocidos como Parafil, con resistenciaa la tracción de 1950MPa y módulo de elasticidad de 126000MPa. La única variable considerada fue la resistencia del concreto, cuyos valores fueron 36, 57, 73, 74 y 104MPa. El concreto de las vigas con resistencia de 57, 73, 74 y 104MPa fueron construidos con el uso de la microsílica y aditivo superplastificante, con excepción de la viga con resistencia de 36MPa que fue construida con concreto común. Los resultados mostraron que la influencia de la resistencia del concreto sobre la resistencia a la flexión de las vigas no es grande. Para el aumento de 189% en la resistencia del concreto, se produjo un aumento en la variación de la fuerza en el cable de apenas 13.6% y un aumento de 33% en el momento de ruptura. Comparando los resultados experimentales con los resultados de las principales normas y modelos propuestos se verificó que todos ofrecen buenos resultados y subestiman los valores experimentales. Comparando los resultados experimentales con el modelo de Campos (1993) se observó que los valores de la variación en la fuerza en el cable superestiman los valores experimentales.

Possibilities of modeling non-linear behavior of concrete within standard room temperatures and increased fire-load values using FEM software ANSYS are studied. Temperature dependences of material models are considered. Fire resistance of reinforced concrete and concrete-steel composite construction is analyzed. Fire loads are defined in accordance with relevant standards. Non-linear structural transient analyses are calculated after temperatures were determined by transient thermal analyses. Results obtained from analyses of simple reinforced concrete structure are compared with approach of isotherm 500 °C method.

The aim of this thesis is to evaluate the real condition of reinforced concrete beam bridge located in Brno Jundrov. In order to evaluate this condition, there was made the main bridge inspection. Subsequently, a number of diagnostic methods were used, such as hardness tests, concrete stress strenght, ultrasonic pulse method, including their evaluation. In terms of the main inspection, the condition of construction of the bridge was evaluated as V - bad. We found out that the concrete from which the bridge is built of is in very good condition. The problem, however, is the condition of the reinforcement located on the bridge. Based on its condition there must be expected lifespan within the next 5-10 years.

The dissertation is composed on theme OF THE SPORTS CENTRE KRUMLOV. In this three-storey building, there is the squash hall, table tennis, fitness hall, sauna for 6 persons and a café. In the garden that belongs to the building, there is projected a course for minigolf, playground for pétanque and tennis court. Constructional system is projected from lime-sand bricks, concrete beam ceilings and glued wooden beams. The roof is flat. External surface finish of the building is the ventilated facade.

This thesis deals with bridging of a lowland valley and the creek Dolanský in the section Jánovce – Jablonov on the Slovak motorway D1. Four variants of the bridge have been developed. Subsequently prestressed single box gilder with large overhangs that are supported by precast struts was selected as the most suitable variant. The construction of the bridge will take place in a formwork suspended on overhead launching scaffolding. The static assessment according to the Europan standard has been drawn up for this variant. The load of the bridge is projected according to the ČSN EN 1991-2 - Traffic loads on bridges and the dimensoin of concrete structures according to the ČSN EN 1992-2 - Concrete bridges - Design and detailing rules. The calculation of load is done using computer software SCIA Engineer 10.1 and Midas Civil.

The diploma thesis is focused on a solution of the load reaction of the bridge construction from girders KA-73. Proposal methods of the nonlinear analysis by means of final elements on the stochastic and deterministic level are used for the solution of the load reaction. A simulation technique Latin Hypercube Sampling is used within the stochastic analysis. A material degradation in the form of the trussing corrosion is solved with the expected decrease of the construction lifetime. The conclusion of the thesis contains an evaluation of initial quantities of material parameters for the load reaction of the construction in the form of the sensitivity analysis.

This thesis deals with the structural-technical survey of beam bridge no. 204c - M1, located in Bystřice pod Hostýnem. The theoretical part of the thesis is devoted to general characteristics of bridges, load capacity of bridges, beam bridges, concrete reinforcement, concrete, diagnosis of reinforced concrete structures, and laboratory evaluation. The practical part deals with carrying out a structural-technical survey on the bridge mentioned above, its evaluation and assessment, recalculation of the load capacity, and design of the necessary rehabilitation to maintain the functionality of the bridge.