To continue the development of the Boundary Layer Data System (BLDS), a constant voltage hot-wire anemometer (CVA) is implemented into the BLDS for flight-testing. The hot-wire anemometer was chosen as an alternative to the traditional pressure probe because of the ability to measure both average velocity and fluctuating velocity within the boundary layer. Previous work done on the benchtop has led to the design of miniaturization, flight-capable hardware for the BLDS. The next step in the development of the BLDS – CVA calls for quantifying the accuracy of the boundary layer measurements measured by the CVA system. To do this, numerous turbulent boundary layer velocity and fluctuating velocity profiles were taken on a flat-plate at various speeds within the Cal Poly 2x2 wind tunnel with both the traditional pressure probe and the CVA. These test resulted showed agreement between the hot-wire and pressure probe data. Once this was completed the new CVA hardware was tested along with the new software that was written for the BLDS – CVA. In addition, due to the limited memory space onboard the BLDS – CVA, an approximation had to be developed to convert the average voltage data from the BLDS – CVA to the average velocity data due to the non-linear calibration function. The approximation developed was able to match the exact values from a traditional calibration. Lastly, due to the inability to perform a laboratory calibration of the hot-wire at altitude, where the conditions differ significantly from the ground conditions, a new procedure for hot-wire calibration was developed. The method developed was validated through wind tunnel testing and a computer thermal/electric model. With the completion of this work, the BLDS – CVA is ready for flight-testing.

Neste trabalho estudamos o movimento de cargas espaciais livres em sólidos dielétricos isolantes ou condutores, sub¬metidos à uma d.d.p. conhecida, admitindo uma distribuição qualquer de cargas que toca inicialmente um dos eletródios.Usando o método das características, reduzimos o problema à solução de uma equação diferencial de la. ordem. Como aplicações, resolvemos os casos de uma densidade linear, quadrática e exponencial, em sólidos com condutividade nula sob a condição de curto-circuito. Observamos que as distribuições tendem rapidamente para distribuições uniformes e, em certos casos, pode ocorrer inversão de corrente, dependendo do tipo de distribuição inicial / Free space charge motion is studied in solid dielectrics, insulators or conductors, under a given voltage. We assume an arbitrary charge distribution contact which is initially in contact with one of the electrodes. Using the \"Method of Characteristics\" we can reduce the problem to the resolution of a first order differential equation. Results are applied for linear, quadratic and exponential charge distributions in solids with zero conductivity under short¬circuit conditions. We saw that the charge profiles fall rapidly to uniform distributions and for cases dependent on initial distributions, current inversions are observed

In recent years, smart gird has received much attention, and many researchers have devoted to home area network (HAN) to improve the efficiency of grid. This thesis proposes a bidirectional isolated DC-DC converter (Dual Active Bridge, DAB) with phase shift control to implement the concept of HAN. Li+Fe battery is used as storage device of the converter, and a bidirectional communication between Laboratory Virtual Instrumentation Engineering Workbench (LabVIEW) and Digital Signal Processor (DSP) is realized by CAN-bus. By setting the current command given by LabVIEW system, the converter is able to charge the Li+Fe battery with constant current and constant voltage method as well as discharge the Li+Fe battery with constant current. Operation principle of the converter and the associated loss are presented.

In this thesis, control schemes for the self-excited induction generator are developed with Matlab/Simulink. Self-excited induction generator is considered as a constant voltage-constant frequency supply for an isolated load. A wind turbine is assumed to be the variable-speed drive of the induction generator. Control schemes aim to ensure a constant voltage-constant frequency operation of the induction generator in case of the variations in the wind speed and/or the load. From the general model of the self-excited induction generator, the characteristics of the system and the dynamic responses of the system in case of any disturbance are examined. Next, the control strategies are developed both for the squirrel-cage rotor induction generator and for the wound-rotor induction generator. Two control loops are necessary for constant voltage-constant frequency operation of a variable speed induction generator, one for the voltage regulation and the other for the frequency regulation. After developing the control loops, constant voltage-constant frequency operation of the self-excited induction generator is simulated with a cage type saturation adaptive induction generator, a fixed capacitor with thyristor controlled reactor (TCR) used for frequency regulation and switched external resistors connected to the stator terminals used for voltage regulation.

Neste trabalho estudamos o movimento de cargas espaciais livres em sólidos dielétricos isolantes ou condutores, sub¬metidos à uma d.d.p. conhecida, admitindo uma distribuição qualquer de cargas que toca inicialmente um dos eletródios.Usando o método das características, reduzimos o problema à solução de uma equação diferencial de la. ordem. Como aplicações, resolvemos os casos de uma densidade linear, quadrática e exponencial, em sólidos com condutividade nula sob a condição de curto-circuito. Observamos que as distribuições tendem rapidamente para distribuições uniformes e, em certos casos, pode ocorrer inversão de corrente, dependendo do tipo de distribuição inicial / Free space charge motion is studied in solid dielectrics, insulators or conductors, under a given voltage. We assume an arbitrary charge distribution contact which is initially in contact with one of the electrodes. Using the \"Method of Characteristics\" we can reduce the problem to the resolution of a first order differential equation. Results are applied for linear, quadratic and exponential charge distributions in solids with zero conductivity under short¬circuit conditions. We saw that the charge profiles fall rapidly to uniform distributions and for cases dependent on initial distributions, current inversions are observed

The development of the constant voltage anemometer (CVA) for the boundary layer data system (BLDS) has been motivated by a need for the explicit autonomous measurement of velocity fluctuations in the boundary layer. The frequency response of a sensor operated by CVA has been studied analytically and experimentally. The thermal lag of the sensor is quantified by a time constant, MCVA. When the time constant is decreased, the half-amplitude cut-off frequency, fCVA, is increased, thereby decreasing the amount of attenuation during measurements. In this thesis, three main approaches have been outlined in theory and tested experimentally to determine the feasibility and effectiveness of implementing them with CVA to limit attenuation: operation at higher Vw, implementation of software compensation, and utilization of smaller diameter sensors. Operation of CVA at higher voltage results in little improvement in frequency response but is accompanied by increased danger of wire burnout. However, sensors do need to be operated at high wire voltages to be more sensitive to velocity fluctuations and less sensitive to temperature fluctuations, without reaching a temperature high enough for wire burnout. Software compensation of the CVA output has been shown not to be useful for measurements with BLDS. The electrical noise present in the CVA measurement system is amplified by the correction algorithm and creates measurements that are not representative of the fluctuations being measured. Decreasing sensor diameter leads to a significant decrease of MCVA and therefore increase of fCVA. Under similar operating conditions, a 2.5 micron diameter sensor showed less roll off in the frequency spectra (measured higher turbulence intensities) than a 3.8 micron diameter sensor for tests in both a turbulent jet and in a turbulent boundary layer. Smaller sensors are more fragile and have been shown to have a decrease in sensitivity as compared to larger sensors; however, for some applications, the increase in frequency response may be worth the trade-off with fragility and sensitivity.

Traditionally, the measurement of turbulence has been conducted using hot-wire anemometry. This thesis presents the implementation of a constant voltage hot-wire anemometer for use with the Boundary Layer Data System (BLDS). A hot-wire calibration apparatus has been developed that is capable of operation inside a vacuum chamber and flow speeds up to 50 m/s. Hot-wires operated with a constant-voltage anemometer (CVA) were calibrated at absolute static pressures down to 26 kPa. A thermal/electrical model for a hot-wire and the CVA circuit successfully predicted the measured CVA output voltage trend at reduced pressure environments; however, better results were obtained when the Nusselt number was increased. A calibration approach that required only one measured flow speed was developed to allow autonomous calibrations of a CVA hot-wire. The single-point calibration approach was evaluated through comparison with the experimental data from the vacuum chamber over a range of 14-50 m/s and at pressures from 26 to 100 kPa. The thermal-electrical model was used to make predictions of CVA output voltage and the corresponding flow speed for conditions that could not be replicated within a laboratory. The first set of predictions were made for conditions from 7.5 to 100 kPa, at a constant temperature of 25⁰C, within a flight speed range of 40 to 150 m/s. Single-point calibrations were developed from these predictions. Additionally, the thermal-electrical model was used to predict hot-wire response for a change in temperature of 25⁰C at 26 kPa and the single-point calibration developed for the pressure range 7.5 to 100 kPa was tested for its ability to adjust. The temperature variation at a single pressure of 26 kPa proved that the single-point function was capable of adapting to off-standard temperatures with the largest deviations of +/- 7% in the mid-range velocities. With a temperature drop, the deviations were below 5%. The second set of thermal-electrical predictions involved conditions for altitude from 0 to 18 km at flow speeds from 40 to 150 m/s. A single-point calibration was developed for altitude conditions. Furthermore, to test the single-point calibration the thermal-electrical model was used to predict hot-re response for a temperature variation of 25⁰C at 18 km. The single-point calibration developed for altitude proved that it was capable of adjusting to a temperature variation of 25⁰C with maximum deviations of about 5% at mid-range velocities. It is proposed that the single-point calibration approach could be employed for CVA measurements with the Boundary Layer Data System (BLDS) to allow hot-wire data to be acquired autonomously during flight tests.

In recent years, the demand for Li-ion-type batteries has been increasing significantly in various fields of applications including portable electronics, electric vehicles, and also in renewable energy support. These applications ask for a highly efficient charging strategy in order to maintain a long life cycle of the batteries. Recently, a new charging technique referred as sinusoidal ripple current-constant voltage charging (SRC-CV) technique has been proposed and is in certain publications claimed to realize an improved charging per-formance on Li-ion batteries than conventional constant-current constant-voltage charg-ing (CC-CV) techniques. In this thesis, the charging performance of the SRC-CV charging method applied to a prismatic Li-ion cell for an automotive traction application is inves-tigated. An existing experimental setup is upgraded to realize charging of the Li-ion cells using the SRC-CV charging method. Electrochemical impedance spectrums of three Li-ion cells have been obtained using electrochemical impedance spectroscopy (EIS). These spectrums were used to determine the charging ripple-current frequency where the mag-nitudes of the ac impedance of the cell are minimized. Key parameters like charging time, discharging time, and energy efficiency are calculated in order to compare the charg-ing performance of the CC-CV and SRC-CV charging techniques. The results reported from the experimental results obtained in this thesis indicate that there is no significant improvement with the SRC-CV charging method (implemented using a constant ripple-current frequency) compared to the CC-CV method in terms of charging time and energy efficiency. / På senare tid har behovet av batterier av Li-jontyp ökat kraftigt inom ett flertal applikationsområden inkluderande portabel elektronik, elfordon och miljövänlig elenergiproduktion. I dessa applikationsområden behövs en högeffektiv laddstrategi för att möjliggöra ett stort antal cyklingar av batterierna. Nyligen har en new laddmetod, benämnd sinusoidal ripple current-constant voltage-laddning (SRC-CV-laddning) föreslagits och har i vissa publikationer demonsterat en förbättring av laddprestanda hos Li-jonbatterier jämfört med konventionell constant-current constant-voltage-laddning (CC-CV-laddning). I detta examensarbete undersöks laddprestandan hos SRC-CV och CC-CV-laddning när de appliceras på prismatiska Li-jonceller avsedda för traktionsdrift. En existerande experimentuppsättning har uppgraderats för att realisera laddcykling med SRC-CV-laddning. Med hjälp av elektrokemisk impedansspektroskopi på tre Li-jonceller har den frekvens vid vilken magnituden på cellernas impedans är minimerad identifierats. Nyckelparametrar såsom laddtid, urladdningstid och energieffektivitet har uppmätts för både SRC-CV- och CC-CV-laddning. De experimentella resultaten visar ingen signifikant förbättring mellan SRC-CV-laddning (implementerat med en konstant rippelströmfrekvens) och konventionell CC-CV-laddning.

Cette thèse se concentre sur la fiabilité des batteries lithium pour des applications véhicules à faible émission en CO2. Pour cela, des méthodologies de caractérisation électriques et thermiques, des protocoles et des tests de vieillissement de batteries lithium sous différents modes (cyclage actif, calendaire simple et cyclage/calendaire) ont été mis en œuvre.Une première partie de ces travaux de thèse s’attache à la modélisation et à l’estimation des états de charge et de santé de la batterie.La deuxième partie est consacrée à l’étude du vieillissement calendaire des batteries lithium utilisant la spectroscopie d’impédance comme méthode de caractérisation. Ensuite, une méthode originale pour l’évaluation de l’état santé de la batterie est proposée. Elle est basée sur l’exploitation de l’étape de charge à tension constante lors d’une recharge complète et est donc bien adaptée à une intégration au sein d’un système de gestion de batterie. L’approche introduite est validée sur des données réelles de vieillissement allant jusqu’à deux ans de test.Enfin, une étude du phénomène de régénération de la capacité suite à un vieillissement des batteries de type combiné cyclage/calendaire est menée. Cette dernière partie constitue une ouverture pour le développement de stratégies d’usage des batteries lithium en incluant leur comportement thermique. / In this thesis, we focus on the reliability of lithium batteries used for automotive applications. For this purpose, electric and thermal characterization methodologies as well as aging tests under several modes (calendar, power cycling, calendar/power cycling) are carried out.In a first part of the work, battery modeling and battery state estimation (state-of-charge and state-of-health) are considered.Then, based on periodic characterization from electrochemical impedance spectroscopy, calendar aging is investigated. Next, we proposed an original process for precise battery state-of-health determination that exploits a full recharge and mainly constant-voltage charge step which allows easily its integration within a battery management system. Our experimental results, up to two years real-life data, confirm effectiveness of our technique.Finally, we study the capacity recovery phenomenon occurring due to combined battery aging (calendar/power cycling). This final part is almost dedicated to introduce strategies for battery use presenting at the same time a thermal behavior study.

The rate of degradation of a lithium-ion battery depends on its use i.e. how it is charged and discharged. Physics-based models are used to represent the processes inside a cell as well as the degradation mechanisms. This thesis aimed to compare how the battery lifetime is affected when charging with different charging protocols using different battery models and degradation mechanisms. The investigated models are the Single Particle Model (SPM), the Single Particle Model with electrolyte (SPMe), and the Doyle-Fuller Newman model (DFN). The degradation mechanisms are solid electrolyte interphase (SEI), and lithium plating (LP). The used charging protocols are constant-current constant voltage(CCCV), positive pulsed current (PPC), and constant current (CC). Pulsed charging was included to investigate if the battery lifetime can be improved as in an experiment by Huang where pulsed charging increased the battery lifetime by 60%. To perform the simulations using the physics-based models, PyBaMM (PythonBattery Mathematical Modeling) was used. The simulations were performed for a lithium cobalt oxide (LCO) cell. Two types of SEI were implemented, solvent-diffusion limited and reaction limited. For the LP only irreversible LP was used.1200 cycles were simulated. Comparing the PPC and CC protocols, there were no significant changes between the degradation mechanisms for the different protocols. The results were the same for all the models, except for the results of the internal resistance. The conclusion is that for the PPC and CC protocols, the cell degrades the same although the PPC protocol used twice the C-rate. The PPC charging did not increase the battery lifetime. For the CCCV and CC protocols, there were some bigger differences between the protocols, but between the different models, there weren’t any significant differences. The CCCV degrades the cell faster for all degradation mechanisms and all models. Simulating one degradation submodel at a time resulted in a very small capacity fade for some submodels. Therefore, for future work, it is suggested to use several degradation submodels at the same time but also to try other degradation mechanisms or try PPC protocols with different frequencies and duty cycles. / Hur snabbt litiumjonbatterier degraderas beror på hur de används, laddas och laddas ur. Fysikbaserde modeller används för att representera processerna inuti cellen och även degraderingsmekanismerna. Denna studie har genomförts för att undersöka hur batteriets livslängd påverkas av olika laddningsprotokoll genom att använda olika batterimodeller och degraderingsmekanismer. Modellerna som användes är Singel-partikelmodellen (SPM), Singel-partikelmodellen med elektrolyt (SPMe) och Doyle-Fuller Newman-modellen (DFN). Degraderingsmekanismerna är fast elektrolytinterfas (SEI) och litiumplätering (LP). Laddningsprotokollen som användes är konstant ström konstant spänning (CCCV), positiv pulserande ström (PPC) och konstant ström konstant (CC). Protokollet för pulsad laddning inkluderades för att undersöka om batteriets livslängd kan förbättras som i ett experiment av Huang, där pulsad laddning ökade batteriets livslängdmed 60%. För att utföra simuleringar med fysikbaserade modeller användes PyBaMM(Pyhton Battery Mathematical Modeling). Simuleringarna utfördes för en lithiumkobaltoxid-cell (LCO). Två typer av SEI implementerades, lösningsmedelsdiffusion-begränsad och reaktions-begränsad SEI. För LP användes endast irreversibel LP.1200 cykler simulerades. Jämförande PPC- och CC-protokollen fanns det inga signifikanta förändringar mellan degraderingsmekanismerna för de olika protokollen. Resultaten vardesamma för alla modellerna, förutom resultaten av den interna resistansen. Slutsatsen är att för både PPC- och CC-protokollen så degraderades cellen på samma sätt, trots att PPC-protokollet använde dubbelt så hög C-faktor. PPC-protokollet ökade inte batteriets livslängd. För CCCV- och CC-protokollen fanns det några större skillnader mellan protokollen, men mellan de olika modellerna fanns det inga signifikanta skillnader. CCCV-protokollet försämrade cellen snabbare för alla degraderingsmekanismer och alla modeller. Att simulera en degraderingsmodell i taget resulterade i mycket små kapacitetsförluster. Därmed föreslås det att i framtida arbete använda flera degraderingsmodeller samtidigt men även testa andra degraderingsmekanismer eller PPC-protokoll med olika frekvenser och arbetscykler