Computations and experiments were run to study heat transfer and overall effectiveness for a simulated turbine blade leading edge. Computational predictions were run for a film cooled leading edge model using a conjugate numerical method to predict the normalized “metal” temperatures for the model. This computational study was done in conjunction with a parallel effort to experimentally determine normalized metal temperatures, i.e. overall effectiveness, using a specially designed high conductivity model. Predictions of overall effectiveness were higher than experimentally measured values in the stagnation region, but lower along the downstream section of the leading edge. Reasons for the differences between computational predictions and experimental measurements were examined. Also of interest was the validity of Taw as the driving temperature for heat transfer into the blade, and this was examined via computations. Overall, this assumption gave reasonable results except near the stagnation line. Experiments were also conducted on a leading edge with no film cooling to gain a better understanding of the additional cooling provided by film cooling. Heat flux was also measured and external and internal heat transfer coefficients were determined. The results showed roughly constant overall effectiveness on the external surface. / text

It is important to keep an overhead power line within rated operating conditions. Thus,an accurate prediction of the conductor's thermal and electrical behavior leads to an increasein reliability and eciency. Under DLR operation, the current rating is adjustedbased on ambient weather and solar conditions to allow for dynamic line loading. Therating adjustment takes into account the cooling mechanisms acting on the conductor. Inthis thesis, cooling by means of convective heat transfer is studied based on wind tunnelexperimental measurements of three dierent conductor samples. Convection contributesto most of the cooling; however, it is aected by wind speed and direction. Two angle ofattacks were studied (40 and 90), where perpendicular ow was found to result in bettercooling. The location of boundary layer separation highly aects the surface distribution ofcooling, which is non-uniform. Oblique wind ow results in reduction in overall cooling dueto earlier boundary layer separation. Finally, the surface average convective heat transfercoecient correlates non-linearly with the Reynolds number, where higher wind speeds andlarger conductor diameters can lead to signicant improvements in cooling while keepingrelatively low current densities. The existing standards of IEEE and CIGRE were found tooverestimate the eect of convective cooling for the specic experimental cases. / Det är viktigt att hålla en kraftöverföringsledning inom nominella driftsförhållanden.Således leder en korrekt förutsägelse av ledarens termiska och elektriska beteende till en ökad tillförlitlighet och effektivitet. Under DLR-drift justeras nuvärdet baserat på omgivande väder och solförhållanden för att möjliggöra dynamisk belastning. Klassificeringsjusteringen tar hänsyn till de kylmekanismer som verkar på ledaren. I denna avhandling studeras kylning med hjälp av konvektiv värmeöverföring baserat på provning av vindtunnel av tre olika ledartyper. Konvektion bidrar till det mesta av kylningen. Det påverkas dock av vindhastighet och riktning. Två angreppsvinkelar studerades (40◦ och 90◦), där vinkelrätt flöde befanns resultera i bättre kylning. Placeringen av ytskiktseparationen har stor inverkan på ytfördelningen av kylning, vilken är ojämn. Skrå vindflöde resulterar i minskning av den totala kylningen på grund av tidigare separering av gränsskiktet. Slutligen korrelerar den ytvärdesöverföringskoefficienten för ytvärdet icke-linjärt med Reynolds-talet, där högre vindhastigheter och större ledardiametrar kan leda till signifikanta förbättringar i kylning samtidigt som relativt låga strömtäthet hålls. De befintliga standarderna för IEEE och CIGRE visade sig överskatta effekten av konvektiv kylning för de specifika experimentellafallen.

Spaces with high occupancy density like classrooms are challenging to ventilate and use a lot of energy to maintain comfort. Usually, a compromise is made between low energy use and good Indoor Environmental Quality (IEQ), of which poor IEQ has consequences for occupants’ health, productivity and comfort. Alternative strategies that incorporate elevated air speeds can reduce cooling energy demand and provide occupant’s comfort and productivity at higher operative temperatures. A ventilation strategy, Intermittent Air Jet Strategy (IAJS), which optimizes controlled intermittent airflow and creates non-uniform airflow and non-isothermal conditions, critical for sedentary operations at elevated temperatures, is proposed herein. The primary aim of the work was to investigate the potential of IAJS as a ventilation system in high occupancy spaces. Ventilation parameters such as air distribution, thermal comfort and indoor air quality are evaluated and the system is compared with a traditional system, specifically, mixing ventilation (MV). A 3-part research process was used: (1) Technical (objective) evaluation of IAJS in-comparison to MV and displacement ventilation (DV) systems. (2) An occupant response study to IAJS. (3) Estimation of the cooling effect under IAJS and its implications on energy use. All studies were conducted in controlled chambers. The results show that while MV and DV creates steady airflow conditions, IAJS has  cyclic airflow profiles which results in a sinusoidal temperature profile around occupants. Air distribution capability of IAJS is similar to MV, both having a generic local air quality index in the occupied zone. On the other hand, the systems overall air change rate was higher than a MV. Thermal comfort results suggest that IAJS generates comfortable thermal climate at higher operative temperatures compared to MV. Occupant responses to IAJS show an improved thermal sensation, air quality perception and acceptability of indoor environment at higher temperatures as compared to MV. A comparative study to estimate the cooling effect of IAJS shows that upper HVAC setpoint can be increased from 2.3 – 4.5 oC for a neutral thermal sensation compared to a MV. This implies a substantial energy saving potential on the ventilation system. In general, IAJS showed a potential for use as a ventilation system in classrooms while promising energy savings. / Lokaler där många människor vistas, som t.ex. klassrum, är ofta svåra att ventilera. Att upprätthålla en bra termisk komfort kräver en hög energianvändning. Vanligtvis blir det en kompromiss mellan låg energianvändning och bra kvalitet på inomhusmiljön (IEQ). Dålig IEQ får konsekvenser för människors hälsa, produktivitet och komfort. Alternativa ventilationsstrategier, som använder förhöjda lufthastigheter, kan minska kylbehovet och därmed energianvändningen. I denna avhandling utvärderas en ny ventilationsstrategi, Intermittenta luftstrålar (IAJS), där korta perioder med hög lufthastighet genererar en svalkande effekt, när rummets temperatur upplevs som för hög. Det primära syftet med arbetet var att undersöka potentialen hos IAJS som ett ventilationssystem för klassrum, där den termiska lasten ofta är hög. Strategin jämförs mot traditionella ventilationsprinciper som omblandande ventilation (MV) och deplacerande ventilation (DV). Parametrar som luftdistributionsindex, termisk komfort, luftkvalitet och energibesparing har utvärderats. Alla studier utfördes i klimatkammare. Resultaten visar att medan MV och DV skapar konstanta luftflödesförhållanden genererar IAJS cykliska hastighetsprofiler samt en sinusformad temperaturvariation i vistelsezonen. IAJS klarar att bibehålla ett bra termiskt klimat vid högre operativa temperaturer jämfört med MV. I en jämförelse med ett traditionellt HVAC-system visar beräkningar  att dess börvärde kan höjas från 2.3 till 4.5 °C med bibehållen termisk komfort. Detta indikerar en avsevärd energibesparingspotential vid användande av IAJS.