Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / This master thesis proposes a current control technique based on sliding mode strategy and disturbance observer for high-performance drive applied to permanent magnet synchronous motors and can be extended to other systems. The combination of sliding mode control and disturbance observer applied to the current control presents the characteristics necessary to minimize the coupling between the axes, rejection of external disturbances and parametric variations. A continuous time control scheme is developed, the stability proofs are performed from the Lyapunov analysis. The performance of the propose technique is evaluates through simulation results. Moreover, this master thesis presents a discrete-time sliding mode controller combined with a discrete-time disturbance observer. The development in discrete-time enables the implementation in digital processors. The conditions of reach of the proposed controller considering the transport delay of digital implementation are still evaluated. The stability proofs of the proposed scheme are presented. Simulation results are shown. In addition, it is developed an experimental platform for drive and control of the permanent magnet synchronous motor in which the experimental results are obtained. / Esta dissertação propõe uma técnica de controle de corrente baseada na estratégia por modos deslizantes e observador de distúrbios para acionamento de alto desempenho aplicada a motores síncronos de ímãs permanentes, podendo ser estendida a outros sistemas. A combinação do controle por modos deslizantes e do observador de distúrbio aplicada ao controle de corrente apresenta as características necessárias para minimização do acoplamento existente entre os eixos, rejeição a distúrbios externos e variações paramétricas. É desenvolvido um esquema de controle em tempo contínuo, são apresentadas as provas de estabilidade a partir de critério de Lyapunov. O desempenho da técnica proposta é avaliado através de resultados de simulação. Além disso, é apresentado um controlador por modos deslizantes associado ao observador de distúrbio em tempo discreto. O desenvolvimento em tempo discreto possibilita a implementação em processadores digitais de sinais. Ainda são avaliadas as condições de alcance do controlador proposto considerando o atraso de transporte da implementação digital. Provas de estabilidade do esquema proposto e resultados de simulação são apresentados. Este trabalho faz o desenvolvimento de uma bancada experimental para o acionamento e controle do motor síncrono de ímãs permanentes na qual são obtidos os resultados experimentais apresentados.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / This work presents an efficient lighting system using high intensity light emitting diodes (LEDs). The goal is to develop a compact and low cost electronic circuit to drive and control the current of LEDs disposed in a single enclosure. The proposal aims energy saving, high luminous efficacy and high useful life when replacing traditional lighting systems, as dichroic, incandescent or compact fluorescent lamps by LEDs without any change in electrical system installation. Furthermore, an emergency lighting system integrated into the lamp is proposed, allowing the use of the same equipment in the daily activities, supplied by mains, and under a possible break in the electrical network. To supply the LEDs through the mains with universal input voltage and charge the battery, a Buck converter was employed. To supply the LEDs with a continuous current through the battery, a Boost converter was used. The converters operate at high frequency and control the current through the LEDs independently. The battery can be composed of three rechargeable Ni-MH batteries (1,2 V) or a Li-ion battery (3,6 V). The design attends the Brazilian standard and international standard for emergency lighting systems. To validate the proposed idea, the circuits were designed and implemented. The experimental results are shown with the intention to prove the satisfactory behavior of the lamps. / Este trabalho apresenta um sistema de iluminação eficiente empregando diodos emissores de luz (LEDs) de alta intensidade. O objetivo é desenvolver um circuito eletrônico, compacto e de baixo custo, para acionamento e controle da corrente dos LEDs contidos em um único invólucro. A proposta visa a racionalização no uso da energia elétrica através de uma elevada eficácia luminosa e longa vida útil na substituição dos sistemas de iluminação tradicionais, como lâmpadas dicróicas, incandescentes ou fluorescentes compactas, por LEDs sem qualquer alteração na instalação elétrica. Além disso, é proposto um sistema de iluminação de emergência integrado a esta lâmpada, permitindo a utilização de um único equipamento para iluminação convencional, alimentada pela rede elétrica, e sob uma possível falha no fornecimento de energia. Para alimentar os LEDs, através da rede elétrica, com tensão de entrada universal e ainda carregar a bateria, um conversor Buck é empregado. Para alimentar os LEDs em corrente contínua através da bateria, um conversor Boost é utilizado. Os conversores operam em alta freqüência e controlam a corrente nos LEDs de forma independente. A bateria pode ser composta por três pilhas recarregáveis de Ni-MH (1,2 V) ou por uma bateria de Li-Ion (3,6 V). O projeto atende às exigências da norma brasileira (NBR 10898) e da norma internacional (IEEE Std 446-1995) para sistemas de iluminação de emergência. Para analisar a idéia proposta, os circuitos são projetados e implementados. Os resultados experimentais são apresentados de forma a comprovar o comportamento satisfatório das lâmpadas.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2018-05-25T12:16:21Z No. of bitstreams: 1 lucasalvesdealmeida.pdf: 7514122 bytes, checksum: a0029ec07180541f754e98112ec47b6b (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2018-06-14T11:52:17Z (GMT) No. of bitstreams: 1 lucasalvesdealmeida.pdf: 7514122 bytes, checksum: a0029ec07180541f754e98112ec47b6b (MD5) / Made available in DSpace on 2018-06-14T11:52:17Z (GMT). No. of bitstreams: 1 lucasalvesdealmeida.pdf: 7514122 bytes, checksum: a0029ec07180541f754e98112ec47b6b (MD5) Previous issue date: 2018-02-27 / Sistemas eletromecânicos são de grande importância atualmente, e a procura por maior eficiência e desempenho aliados a um menor custo justificam a busca por alternativas tanto em topologia quanto no controle e acionamento de tais sistemas. A máquina de relutância chaveada é capaz de cumprir estes requisitos e tem despertado o interesse de pesquisadores e empresas nos últimos anos, emergindo como uma alternativa viável em diversas aplicações. Porém, esta máquina possui características singulares. Por conta de sua estrutura duplamente saliente, seu funcionamento correto depende da aplicação de pulsos de corrente por determinados intervalos de tempo, e na sequência correta, seus parâmetros são variáveis no tempo, apresentando um comportamento com características não-lineares. Tais particularidades fazem com que seja difícil controlar o torque destas máquinas, as quais possuem a tendência de apresentar altas oscilações durante a mudança da excitação de cada fase. Este trabalho tem por objetivo contribuir com o estudo da modelagem e do acionamento de uma máquina de relutância chaveada. É apresentada sua modelagem matemática e um modelo de simulação que leva em consideração as não linearidades existentes. Em seguida são apresentadas técnicas de controle de corrente que incluem um regulador de histerese, um controlador PI e um controlador por modos deslizantes. Também é utilizado um método capaz de determinar o momento em que cada fase deve ser acionada, baseado no ângulo do rotor, e uma técnica de variação dos ângulos de acionamento de maneira dinâmica, usados em conjunto com os controladores propostos. O trabalho também caracteriza e apresenta as funções de divisão de torque como uma maneira de reduzir drasticamente as oscilações de torque. São apresentadas as operações como motor e como gerador, bem como um exemplo de aplicação de modo a ilustrar ambos os modos de operação. / Electromechanical systems have a huge relevance nowadays, and seeking for improvements in efficiency and performance at the lowest cost make valid to identify topological and control alternatives of these systems. The switched reluctance machine is capable to fulfill such requirements and emerges as an interesting field of research. Academics and industrial works shows that it is a promising alternative in several applications. However, this machine presents unique characteristics, like the doubly salient structure, the necessity to apply phase currents in a sequence determined by the stator/rotor pole ratio, its time variantparameters,andthestrongnonlinearcharacteristics. Suchsingularitiesmaketorque control hard, as it tends to present high ripples and makes a lot of noise. This thesis aims to contribute on switched reluctance machine modeling and drive system. A mathematical model is presented, and also a simulation model that accounts for nonlinearities, making possible to simulate the machine accurately in a computational environment. A hysteresis regulator, a PI controller and a sliding mode controller are designed and simulated. An algorithm to determine when each phase should be excited based on rotor angle is used, and a technique to change such firing angles dynamically is developed that can be used along with current control methods presented. The work also defines and presents torque sharing functions as a way to greatly reduce torque ripple. Motor and generator operation are contemplated, and both modes are illustrated in an application example.

This work deals with a proposal and construction of a DC/DC converter for a control of a DC motor Heinzmann. The DC/DC converter will be used in an electric drive for a bicycle. The proposal of the DC/DC converter is designed for such engine power to avoid fully any human force to drive - pedaling. The work includes informations about the used motor, progress of proposal and dimensioning of the converter - power circuit and control electronics.

This thesis deals with the peripheral design, construction design and implementation welder DC arc. The concept of welder is based on the use of two single action forward converter working-pull. Converters operate at a frequency of 60 kHz. Output current can be adjusted in the range from 0 to 140 A. After switching function the welder can operate as a battery charger. Charging current can be adjusted in the range of 0-70 A. The device is powered from a single phase supply 230 V.

The diploma thesis is a part of the project Intelligent double arm juggling machine. The project is divided into two diploma thesis. This thesis deals with the motion control of juggling arms. Information about hardware and software resources used in this project is in the first part of thesis. There is explanation of the control loop, explanation of used communication protocols and implementation of program proceeding in the second part of thesis.

The installation of wind power plant has significantly increased since several years due to the recent necessity of creating renewable and clean energy sources. Before the accomplishment of a wind power project many pre-studies are required in order to verify the possibility of integrating a wind power plant in the electrical network. The creation of models in different software and their simulation can bring the insurance of a secure operation that meets the numerous requirements imposed by the electrical system. Hence, this Master thesis work consists in the creation of a wind turbine model. This model represents the turbines installed at Lillgrund wind farm, the biggest wind power plant in Sweden. The objectives of this project are to first develop an accurate model of the wind turbines installed at Lillgrund wind farm and further to use it in different kinds of simulations. Those simulations test the wind turbine operating according to different control modes. Also, a power quality analysis is carried out studying in particular two power quality phenomena, namely, the response to voltage sags and the harmonic distortion. The model is created in the software PSCAD that enables the dynamic and static simulations of electromagnetic and electromechanical systems. The model of the wind turbine contains the electrical machine, the power electronics (converters), and the controls of the wind turbine. Especially, three different control modes, e.g., voltage control, reactive power control and power factor control, are implemented, tested and compared. The model is tested according to different cases of voltage sag and the study verifies the fault-ride through capability of the turbine. Moreover, a harmonics analysis is done. Eventually the work concludes about two power quality parameters.

No description available.

Ce manuscrit de thèse propose l'optimisation de l'ensemble de la chaîne de reproduction sonore dans un système embarqué. Le premier axe de recherche introduit les notions générales concernant les systèmes audio embarqués nécessaires à la bonne compréhension du contexte de la recherche. Le principe de conversion de l'ensemble de la chaine est présenté afin de comprendre les différentes étapes qui composent un système audio. Un état de l'art présente les différents types de haut-parleurs ainsi que l'électronique associé les plus couramment utilisées dans les systèmes embarqués. Le second axe de recherche propose une approche globale : une modélisation électrique du haut-parleur (tenant compte d'un nombre optimal de paramètres) permet à un électronicien de mieux appréhender les phénomènes non-linéaires du haut-parleur qui dégradent majoritairement la qualité audio. Il en résulte un modèle viable qui permet d'évaluer la non-linéarité intrinsèque du haut-parleur et d'en connaitre sa cause. Les résultats des simulations montrent que le taux de distorsion harmonique intrinsèque au haut-parleur est supérieur à celui généré par un amplificateur. Le troisième axe de recherche met en avant l'impact du contrôle du transducteur. L'objectif étant de savoir s'il existe une différence, du point de vue de la qualité audio, entre la commande asservie par une tension ou par un courant, d'un micro-haut-parleur électrodynamique. Pour ce type de transducteur et à ce niveau de la modélisation, le contrôle en tension est équivalent à contrôler directement le haut-parleur en courant. Néanmoins, une solution alternative (ne dégradant pas davantage la qualité audio du signal) pourrait être de contrôler le micro-haut-parleur en courant. Le quatrième axe de recherche propose d'adapter les spécifications des amplificateurs audio aux performances des micro-haut-parleurs. Une étude globale (énergétique) démontre qu'un des facteurs clés pour améliorer l'efficacité énergétique du côté de l'amplificateur audio est la minimalisation de la consommation statique en courant, en maximalisant le rendement à puissance nominale. Pour les autres spécifications, l'approche globale se base sur l'étude de l'impact de la spécification d'un amplificateur sur la partie acoustique. Cela nous a par exemple permis de réduire la contrainte en bruit de 300%. Le dernier axe de recherche s'articule autour d'un nouveau type de transducteur : un micro-haut-parleur en technologie MEMS. La caractérisation électroacoustique présente l'amélioration en terme de qualité audio (moins de 0,016% de taux de distorsion harmonique) et de plage de fréquence utile allant de 200 Hz à 20 kHz le tout pour un niveau sonore moyen de 80dB (10cm). La combinaison de tous les efforts présente un réel saut technologique. Enfin, la démarche globale d'optimisation de la partie électrique a été appliquée aux performances du MEMS dans la dernière section, ce qui a notamment permis de réduire la contrainte en bruit de 500%. / This thesis proposes the optimization of the whole sound reproduction chain in an embedded system. The first research axis is introduces the general concepts concerning audio systems necessary for the good understanding of the context of research. The principle of conversion of the entire chain is presented to understand the stages that make up a sound system. A state of the art presents various loudspeakers and the associated electronics most commonly used in embedded systems. The second research axis proposes a global approach: electric modeling of loudspeaker (taking into account an optimum number of parameters) that allows electronics engineer a better understanding of the nonlinear phenomena that degrade mostly audio quality in loudspeakers. It results in a sustainable model which evaluates the intrinsic non-linearity in loudspeakers and to know its cause. The simulation results show that the total harmonic distortion intrinsic to the loudspeaker is higher than that the distortion generated by an amplifier. The third research axis highlights the impact of the control of the transducer. The aim is to find out if there is a difference, in terms of audio quality, between the feedback control by voltage or current, for an electrodynamic micro-speaker. For this type of transducer and at this level of modeling, voltage control is equivalent to directly control the current of the micro-speaker. However, an alternative solution (not further degrading the signal audio quality) could be to control directly the micro-speaker by a current. The fourth research axis proposes to adapt the audio amplifiers specification to the performance of the micro-speakers. A comprehensive study of an energy point of view shows that a key factor for improving the energy efficiency of the audio amplifier is the minimization of the static power consumption and the maximization of the performance at nominal power. For other specifications, the global approach is based on the study of the impact of the specification of an amplifier on the sound pressure level. This has allowed, for example to reduce the stress in output noise voltage by a ratio of 300 %. The last research axis focuses on a new type of transducer: a micro-speaker in MEMS technology. Electroacoustic characterization shows the improvement: in terms of audio quality (less than 0.016 % total harmonic distortion) and the useful frequency range from 200 Hz to 20 kHz, the whole for an average sound level of 80 dB (10 cm). The combination of all the efforts presents a real technological leap. Finally, the overall process of optimization of the electrical part has been applied to the performance of MEMS in this last section, which has resulted, for example, in a reduction in the noise constraint of 500 %.

Esta tesis doctoral trata acerca de los sistemas de compensación activos de conexión en paralelo utilizados para la mejora de la calidad del suministro eléctrico, y de la eficiencia energética en las redes eléctricas de distribución y en las instalaciones, a cuatro hilos. En la presente tesis se desarrolla un nuevo filtro o compensador activo de potencia con la capacidad de seleccionar los fenómenos a compensar, incluyéndose además algunas propuestas que, aplicadas a estos sistemas de compensación, permiten mejorar las prestaciones finales obtenidas. Se presentan las estrategias de compensación global más utilizadas en compensadores activos y se propone un método de compensación global basado en la norma IEEE Std. 1459-2000. Se realiza un estudio comparativo de las diferentes estrategias de compensación global. Para la obtención de un compensador selectivo, se proponen dos métodos diferentes para la descomposición de las corrientes de carga y la obtención de las corrientes de compensación. El primer método está basado en la utilización de las conductancias por fase y la conductancia equivalente del sistema trifásico. El segundo se basa en la descomposición de potencias propuesta en la IEEE Std. 1459-2000. Se presenta un análisis de cada uno de los métodos propuestos. Se presenta el análisis del sistema completo para la implementación del compensador selectivo propuesto. El sistema de control incluye, la utilización de la técnica de la ventana deslizante para la obtención de las corrientes de referencia, el desarrollo de un regulador de corriente de bajo coste computacional, el diseño del regulador para el control del bus dc y el desarrollo de un nuevo modulador vectorial tridimensional 3D-3B SVPWM. Finalmente, se presentan los resultados de simulación y experimentales del sistema de compensación diseñado, para diferentes tipos de cargas y condiciones de alimentación. Parte de estos resultados han sido presentados, entre otras, en las siguientes publicaciones: " S. O / Orts Grau, S. (2008). Sistema de compensación mediante filtro activo de potencia con sistema de obtención de las corrientes de referencia selectivo utilizando control 3D-3B SVPWM de la etapa de potencia. Aplicación a sistemas industriales a 4 hilos [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/3797 / Palancia