Water is becoming scarcer and several authors have highlighted the upcoming problem of higher water salinity and the difficulty of treating and discharging water. Moreover, current discoveries of problems with chemicals that have been used for pretreating or post-treating water alerted scientists to research better solutions to treat water. Membrane distillation (MD) is a promising technology that might replace current processes as it has lower pretreatment requirements combined with a tremendous ability to treat a wide range of feed sources while producing very high product quality. If it enters the market, it will have a big influence on all products, from food industry to spaceflight. However, there are several problems which make MD a hot topic for research. One of them is the question about the real cost of MD in terms of heating feed and cooling distillate over time with respect to product quantity and quality. In this work, extensive heating and cooling analyses are covered to answer this question in order to enhance the MD process. Results show energy cost to produce water and the main source of energy loss for direct contact membrane distillation (DCMD), and several suggestions are made in order to better understand and hence enhance the process.

Visual environments may contain a complex combination of object motion. Animals respond to features of complexity by generating adaptive behavioural responses. One important feature of a complex visual environment is a rapidly expanding object in the visual field (looming) which may represent an approaching predator or an object on a collision path. Many animals respond to looming objects by generating avoidance behaviours (Maier et al. 2004; Santer et al. 2005; Oliva et al. 2007) and neurons involved in the detection and relay of looming stimuli are present in birds (Sun and Frost 1998) and many insects (Simmons and Rind 1992; Hatsopoulos et al. 1995; Wicklein and Strausfeld 2000). One of the most widely studied visual pathways is found in the locust. This visual pathway, which includes the lobula giant motion detector (LGMD) and its post-synaptic target, the descending contralateral motion detector (DCMD), signals the approach a looming visual stimulus (Schlotterer, 1977; Simmons and Rind, 1992; Hatsopoulos et al., 1995). The DCMD descends through the ventral nerve cord and synapses with motorneurons involved in predator evasion and collision avoidance (Simmons, 1980; Simmons and Rind, 1992; Santer et al., 2006).<p> Previous studies have suggested that this pathway is also affected by more complicated movements in the locusts visual environment. For example, Guest and Gray (2006) demonstrated that the approach of paired objects in the azimuthal position and approaches at different time intervals affect DCMD firing rate properties. In my first objective of this thesis (Chapter 2), I tested locusts with computer-generated discs that traveled along a combination of non-colliding (translating) and colliding (looming) trajectories and demonstrate how distinctly different DCMD responses result from different trajectory types. In addition to estimating the time of collision and direction of object travel, the presence of a discernable peak associated with the time of object deviation suggests that DCMD responses may contain information related to changes in motion.<p> Previous studies suggest that LGMD/DCMD encodes approaching objects using rate coding; edge expansion of approaching objects causes an increased rate of neuronal firing (Schlotterer, 1977; Hatsopoulos et al., 1995; Judge and Rind, 1997; Gabbiani et al., 1999). Based on observations of DCMD responses to simple looming objects that showed oscillations in DCMD responses (for example, Fig. 1D Santer et al., 2006) and the fact that bursting occurs in many other sensory systems (Yu and Margoliash, 1996; Sherman, 2001; Krahe and Gabbiani, 2004; Marsat and Pollack, 2006), it was hypothesized that the DCMD may show bursting activity. In my second objective of this thesis (Chapter 3), I tested locusts with simple looming stimuli known to generate behavioural responses in order to identify and quantify bursting activity. Results show that the highest frequency of bursts occurred at intervals of 40-50 ms (20-25 Hz). The behavioural significance of this frequency is related to the average wingbeat frequency of the locusts forewing during flight (~25 Hz; Robertson and Johnson, 1993). Based on previous evidence of DCMD flight-gating (see, for example, Santer et al., 2006), bursting may gate information into the flight circuitry, thereby providing visual feedback that may be modified to generate an avoidance response during flight. Single spiking and bursting occurred throughout object approach up until the late stage of approach, where burst frequency rapidly increased. Results predict that the DMCD may use a bimodal coding strategy to detect looming visual stimuli, where single spiking at the beginning of approach may result in subtle course changes during flight and bursting near the time of collision may initiate an evasive glide.<p> Taken together, these results illustrate that the encoding of visual stimuli in single neurons is dynamic and likely much more complicated than previously thought.

Visual environments may contain a complex combination of object motion. Animals respond to features of complexity by generating adaptive behavioural responses. One important feature of a complex visual environment is a rapidly expanding object in the visual field (looming) which may represent an approaching predator or an object on a collision path. Many animals respond to looming objects by generating avoidance behaviours (Maier et al. 2004; Santer et al. 2005; Oliva et al. 2007) and neurons involved in the detection and relay of looming stimuli are present in birds (Sun and Frost 1998) and many insects (Simmons and Rind 1992; Hatsopoulos et al. 1995; Wicklein and Strausfeld 2000). One of the most widely studied visual pathways is found in the locust. This visual pathway, which includes the lobula giant motion detector (LGMD) and its post-synaptic target, the descending contralateral motion detector (DCMD), signals the approach a looming visual stimulus (Schlotterer, 1977; Simmons and Rind, 1992; Hatsopoulos et al., 1995). The DCMD descends through the ventral nerve cord and synapses with motorneurons involved in predator evasion and collision avoidance (Simmons, 1980; Simmons and Rind, 1992; Santer et al., 2006).<p> Previous studies have suggested that this pathway is also affected by more complicated movements in the locusts visual environment. For example, Guest and Gray (2006) demonstrated that the approach of paired objects in the azimuthal position and approaches at different time intervals affect DCMD firing rate properties. In my first objective of this thesis (Chapter 2), I tested locusts with computer-generated discs that traveled along a combination of non-colliding (translating) and colliding (looming) trajectories and demonstrate how distinctly different DCMD responses result from different trajectory types. In addition to estimating the time of collision and direction of object travel, the presence of a discernable peak associated with the time of object deviation suggests that DCMD responses may contain information related to changes in motion.<p> Previous studies suggest that LGMD/DCMD encodes approaching objects using rate coding; edge expansion of approaching objects causes an increased rate of neuronal firing (Schlotterer, 1977; Hatsopoulos et al., 1995; Judge and Rind, 1997; Gabbiani et al., 1999). Based on observations of DCMD responses to simple looming objects that showed oscillations in DCMD responses (for example, Fig. 1D Santer et al., 2006) and the fact that bursting occurs in many other sensory systems (Yu and Margoliash, 1996; Sherman, 2001; Krahe and Gabbiani, 2004; Marsat and Pollack, 2006), it was hypothesized that the DCMD may show bursting activity. In my second objective of this thesis (Chapter 3), I tested locusts with simple looming stimuli known to generate behavioural responses in order to identify and quantify bursting activity. Results show that the highest frequency of bursts occurred at intervals of 40-50 ms (20-25 Hz). The behavioural significance of this frequency is related to the average wingbeat frequency of the locusts forewing during flight (~25 Hz; Robertson and Johnson, 1993). Based on previous evidence of DCMD flight-gating (see, for example, Santer et al., 2006), bursting may gate information into the flight circuitry, thereby providing visual feedback that may be modified to generate an avoidance response during flight. Single spiking and bursting occurred throughout object approach up until the late stage of approach, where burst frequency rapidly increased. Results predict that the DMCD may use a bimodal coding strategy to detect looming visual stimuli, where single spiking at the beginning of approach may result in subtle course changes during flight and bursting near the time of collision may initiate an evasive glide.<p> Taken together, these results illustrate that the encoding of visual stimuli in single neurons is dynamic and likely much more complicated than previously thought.

<p>Current global water scarcity and the spectre of a future critical shortage are driving the need for novel and energy saving water technology approaches. Desalination of seawater and the reuse of treated wastewater effluent, which have historically been viewed as undesirable water sources, are increasingly being explored as sources for reducing water consumption. Although the dominant technologies for taking these water sources to potable quality, energy consumption still makes them unsustainable for widespread application. Membrane distillation (MD) is an innovative water purification method that has shown promise as a technology that can address several of these issues. MD is a membrane process that produces very high quality product water. However, similarly to other thermal desalting processes, MD utilizes heat as the dominant source of energy rather than pressure, and can potentially be used to produce water at higher recoveries (and therefore less waste) than is feasible with existing approaches. Another important advantage of MD is that the water separation occurs at modest temperatures (<90oC), opening the door for the utilization of currently usable waste heat sources. Despite these advantages, MD is primarily a lab scale technology, and key questions concerning process performance, including flux magnitude, energy efficiency, fouling propensity, membrane performance, and long-term system performance must be addressed to fully vet this technology. </p><p>This work is represents an attempt to provide insight into several of these issues. The overarching approach taken throughout this project is the parallel evaluation of ceramic membranes alongside commonly used polymeric (PTFE) membranes. The combined factors of MD being a relatively nascent technology and the fundamental separation mechanism point toward initial real-world applications of MD for the treatment of high concentration water that may necessitate membranes exposure to harsher thermal and chemical environments. The robust and inert nature of ceramics make them ideal candidates for such application, although their hydrophilic surface do allow for direct implementation in MD. The first phase of this work details the evaluation of several candidate surface treatments for modifying ceramic membranes and shows that aluminum oxide ceramic membranes can be successfully modified with perfluorodecyltriethoxysilane to possess the necessary hydrophobicity for MD application. The effectiveness of the surface treatment in modifying the membrane surface chemistry was assessed using a multitude of analytical approaches, which showed that the modified ceramic surface attained high hydrophobicity and thus are suitable for application of the membranes in direct contact membrane distillation (DCMD).</p><p>The next phase of research details the development and verification of a model for DCMD performance. The relative membrane performance was compared, with the polymeric membrane consistently outperforming the modified ceramics, which was attributed to a combination of superior thermal and physical membrane characteristics. Beyond attempting to evaluate the performance differences, this model allows the consideration of various operational scenarios, focusing on membrane flux and energy performance as various membrane and operational parameters change to determine conditions that maximize MD performance as well as provide insight critical to develop MD-specific membranes. </p><p>Finally, membrane performance was evaluated during the treatment water containing various organic foulants as well for the treatment of municipal wastewater. The results showed that the level of fouling was highly dependent on foulant type, with alginate identified as a component that produces severe fouling under all conditions evaluated, and wastewater fouling being relatively minimal. Membrane cleaning solutions were implemented to show that near-complete flux recovery was attainable, and plain deionized water was shown to be as effective as sodium hypochlorite.</p> / Dissertation

Processing information in the nervous system is energetically expensive, constraining the ability of the system to survive disturbances caused by stress. While some organisms compensate for extreme changes in the abiotic features of their environment, the mechanisms underlying this are poorly understood. We used the locust Descending Contralateral Movement Detector (DCMD) neuron to study how the propagation characteristics of action potentials (APs) change following an acute energy stress in control and heat shock (HS) pre-treated animals. We also attempted to determine if Ca2+ is involved in the DCMD AP and the possible changes indicated above. Conduction velocity decreased over an hour of recording in all groups, except those with minimal dissections, and we observed an increase in AP half-width and a decrease in the slope of the rising phase of the AP over time. After HS pre-treatment the response to a standard looming stimulus was delayed, showed significantly fewer APs and a lower peak frequency compared to controls. Brief application of sodium azide (NaN3) as an acute metabolic inhibitor did not subsequently affect DCMD’s conduction velocity or ability to fire at high frequencies during the recording period. There were no significant differences from control animals with extracellular Ca2+ manipulations; however we cannot conclude that Ca2+ does not contribute to DCMD’s AP because Na+ could have flowed through Ca2+ channels in the absence of extracellular Ca2+. Furthermore, examination of possible performance impairments with decreased Ca2+ currents, to indicate if Ca2+ current manipulation may account for the performance impairment, could not be conducted because no differences in AP characteristics were observed with Ca2+ manipulations. We suggest that the slowing of propagation in all groups represents a response to energetic stress and that HS modifies neuronal properties in ways that can be interpreted as saving energy in case of future stressors. / Thesis (Master, Neuroscience Studies) -- Queen's University, 2009-08-11 08:36:26.571

With the increase of population every year, fresh water scarcity has rapidly increased and it is reaching a risky level, particularly in Africa and the Middle East. Desalination of seawater is an essential process for fresh water generation. One of the methods for desalination is membrane distillation (MD). MD process separates an aqueous liquid feed across a porous hydrophobic membrane to produce pure water via evaporation. Polyvinlidene fluoride (PVDF) membranes reinforced with a polyester fabric were fabricated as potential candidates for MD. Non-solvent induced phase separation coupled with steam treatment was used to prepare the PVDF membranes. A portion of the prepared membrane was coated with Teflon (AF2400) to increase its hydrophobicity. In the first study, the fabricated membranes were characterized using scanning electron microscopy and other techniques, and they were evaluated using direct contact MD (DCMD). The fabricated membranes showed a porous sponge-like structure with some macrovoids. The macrovoid formation and the spongy structure in the membrane cross-sections contributed significantly to a high permeate flux as they provide a large space for vapor water transport. The modified PVDF membranes with steaming and coating exhibited a permeate flux of around 40 L/h m2 (i.e. 27-30% increase to the control PVDF membrane) at temperatures of 60 °C (feed) and 20 °C (permeate). This increase in the permeate flux for the modified membranes was mainly attributed to its larger pore size on the bottom surface. In the second study, the control PVDF membrane was tested in two different module designs (i.e. semi-circular pipe and rectangular duct module designs). The semi-circular module design (turbulent regime) exhibited a higher permeate flux, 3-fold higher than that of the rectangular duct module design (laminar regime) at feed temperature of 60 °C. Furthermore, a heat energy balance was performed for each module design to determine the temperature polarization coefficients (TPC). The turbulent module design showed higher TPC (0.5-0.58) than the laminar module (0.1-0.14) (i.e. a poor module design). This indicates that the effect of temperature polarization on the laminar flow was significant, which is below the reported TPC range of 0.4-0.70.

Neurons perform complex computations, communications and precise transmissions of information in the form of action potentials (APs). The high level of heterogeneity and complexity at all levels of organization within a neuron and the functional requirement of highly permeable cell membranes leave neurons exposed to damage when energy levels are insufficient for the active maintenance of ionic gradients. When energy is limiting the ionic gradient across a neuron’s cell membrane risks being dissipated which can have dire consequences. Other researchers have advocated “generalized channel arrest” and/or “spike arrest” as a means of reducing the neuronal permeability allowing neurons to adjust the demands placed on their electrogenic pumps to lower levels of energy supply. I investigated the consequences of hypoxia on the propagation of a train of APs down the length of a fast conducting axon capable of transmitting APs at very high frequencies. Under normoxic conditions I found that APs show conduction velocities and instantaneous frequencies nearly double that of neurons experiencing energy limiting hypoxic conditions. I show that hypoxia affects AP conduction differently for different lengths of axon and for APs of different instantaneous frequencies. Action potentials of high instantaneous frequency in branching lengths of axon within ganglia were delayed more significantly than those in non-branching lengths contained within the connective and fail preferentially in branching axon. I found that octopamine attenuates the effects of hypoxia on AP propagation for the branching length of axon but has no effect on the non-branching length of axon. Additionally, for energetically stable cells, application of the anti-diabetic medication metformin or the hyperpolarization-activated cyclic nucleotide-gated (HCN) channel blocker ZD7288 resulted in a reduced performance similar to that seen in neurons experiencing energetic stress. Furthermore both metformin and ZD7288 affect the shape of individual APs within an AP train as well as the original temporal sequence of the AP train, which encodes behaviourally relevant information. I propose that the reduced performance observed in an energetically compromised cell represents an adaptive mechanism employed by neurons in order to maintain the integrity of their highly heterogeneous and complex organization during periods of reduced energy supply. / Thesis (Master, Biology) -- Queen's University, 2011-10-07 14:41:46.972

Membrane distillation (MD) is a promising desalination technology which allows to achieve high salt rejection at low energy expenses as compared to conventional desalination processes. However, just like in any other membrane separation process, the MD membrane is susceptible to biofouling which is one of the critical problems in membrane-based systems. In this study, we investigated the effects of spacer design and feed temperature on the biofilm formation and proliferation in a flat-sheet direct contact membrane distillation (DCMD) used for desalination of the Red Sea water. Two types of spacers (Standard & 1-Hole) were designed to evaluate their efficiency in biofouling mitigation at three different feed water temperatures (47 °C, 55 °C and 65 °C). Our results showed that while 1-hole spacer was more efficient in reducing biofouling at 47 °C (permeate flux declines of 73.2% and 79.6% after 5 days of DCMD process using 1-hole and standard spacers, respectively). Standard spacer over-performed at higher feed water temperatures (65.7%, and 75.2% after 5 days of DCMD process at 55 °C and 65 °C, respectively). The Optical Coherence Tomography (OCT) revealed a significant transition of biofilm morphology with increasing feed water temperature for both types of spacers. While thicker and more porous biofouling structures were formed on the surface of MD membrane at 47 °C and 55 °C, thinner non-porous layer prevailed on the membrane surface at a feed water temperature of 65 °C. This observation was supported by direct enumeration of bacterial cells inside the biofilm by flow cytometry which revealed a significant decrease in the total number of cells when the feed water temperature was increased from 55 °C to 65 °C. Moreover, this process was accompanied by the permeate flux decline and increase of coolant water conductivity regardless of the spacer type. The results of our study have shown high rejection of dissolved organic carbon (DOC > 97%) and absence of bacterial contamination of permeate water which is important due to use of microporous polymeric membrane with 0.5 m pore size. The obtained results indicated the importance of operational conditions in controlling the biofouling in the MD system.

Membrane Distillation (MD) is an emerging sustainable desalination technique. While MD has many advantages and can be powered by solar thermal energy, its main drawback is the low water production rate. However, the MD process has not been fully optimized in terms of its manipulated and controlled variables. This is largely due to the lack of adequate dynamic models to study and simulate the process. In addition, MD is prone to membrane fouling, which is a fault that degrades the performance of the MD process. This work has three contributions to address these challenges. First, we derive a mathematical model of Direct Contact Membrane Distillation (DCMD), which is the building block for the next parts. Then, the proposed model is extended to account for membrane fouling and an observer-based fouling detection method is developed. Finally, various control strategies are implemented to optimize the performance of the DCMD solar-powered process. In part one, a reduced-order dynamic model of DCMD is developed based on lumped capacitance method and electrical analogy to thermal systems. The result is an electrical equivalent thermal network to the DCMD process, which is modeled by a system of nonlinear differential algebraic equations (DAEs). This model predicts the water-vapor flux and the temperature distribution along the module length. Experimental data is collected to validate the steady-state and dynamic responses of the proposed model, with great agreement demonstrated in both. The second part proposes an extension of the model to account for membrane fouling. An adaptive observer for DAE systems is developed and convergence proof is presented. A method for membrane fouling detection is then proposed based on adaptive observers. Simulation results demonstrate the performance of the membrane fouling detection method. Finally, an optimization problem is formulated to maximize the process efficiency of a solar-powered DCMD. The adapted method is known as Extremum Seeking (ES). A Newton-based ES is designed and the proposed model is used to accurately forecast the distilled water flux. Although good results are obtained with this method, a practical modification to the ES scheme is proposed to enhance the practical stability.

No description available.