A novel method of producing die compacted powder metallurgy components with fully en-closed internal structures was developed. The physical characteristics of the compacts were evaluated by measuring bulk density, internal density gradients and compressive green strength. Additionally, a finite element simulation was developed to evaluate the compaction process of the internal structure compact. The internal structure compact displayed the anticipated lower bulk densities due to the less dense internal structure than a conventional powder metallurgy compact, however; higher local densities were found within the internal structure compact at all compaction pressures. Compressive green strength characteristics showed unique results where the strength in-creased up to 300 MPa compaction pressure, however; at 400 MPa there was a distinct plat-eau in green strength. This phenomenon was attributed to an increase in differential shear stress around the internal structure with a minimal increase in density from 300 MPa to 400 MPa.

A new methodology was developed to observe and measure tool wear during the die compaction process. The newly developed method is a non-destructive test using silicon rubber to transcript die surface profiles. Tool wear was observed and measured by recording surface roughness and diameter of the cylindrical die replicas on a surface profiler including weight loss in the die. To validate this procedure, an aluminum alloy powder without lubricant was compacted to examine the effect on die wear. The die materials were machined from several wrought and composite materials. A further dimension to the program was the variance of compaction pressures and lubricants.

Currently, there is a high demand for lightweight aerospace materials, driven by the desire to provide enhanced fuel efficiency by reducing vehicular weight. Aluminum alloys are attractive due to their excellent mechanical properties and high strength to weight ratios. Powder metallurgy (PM), which converts metal powder into a high performance product, presents an alternative to traditional forming techniques, which are often unable to provide adequate dimensional tolerances. The challenge is to determine if aluminum PM alloys and technologies can be successfully employed within aerospace applications. This research focuses on the PM processing technologies (die compaction, cold isostatic pressing (CIP), and spark plasma sintering (SPS)) of two alloys, PM2024 and PM7075. Processing parameters were assessed using attributes such as density, hardness, and tensile properties. Both powders showed comparable densities and tensile properties to their wrought equivalents. Ultimately, the groundwork was laid for future research into these alloys and their processing methods.

Titanium is well known for its excellent properties, such as high strength-to-weight ratio and outstanding corrosion resistance. However the high cost of this metal has confined its applications to those mostly within the aerospace and military industries. The high purchase price of titanium is primarily driven by the need for intricate metal extraction processes, as well as the sensitivity towards conventional metal working operations. Among the potential solutions, powder metallurgy (P/M) technology provides an economical approach to bring down the price of finished titanium products. However, there are still many problems, such as the residual porosity in the sintered body, that need to be overcome. In this thesis, a fundamental study was carried out focusing on the P/M press-and-sinter technique, using commercially pure titanium (CP Ti) as well as two binary titanium alloys, namely Ti-Ni and Ti-Sn. The influence of several processing parameters including compaction pressure, lubricant type/concentration, sintering time/temperature were performed on both the CP and binary systems. The principal tools utilized for mechanical characterization were hardness and tensile testing, whereas optical microscopy, x-ray diffraction (XRD), and scanning electron microscopy were employed to identify the microstructural features present. Press-and-sinter P/M strategies were successfully developed for all of the blends studied. For CP-Ti, a maximum tensile strength >750MPa and near full theoretical density (~99%) were achieved. Transitions in the size and the size distribution of pores and ?-Ti grains were also observed and quantified. It was found these transitions, as well as the powder impurities present (i.e. oxygen and carbon), greatly influenced the final mechanical properties. In the case of the binary alloys, it was shown that liquid phase sintering (LPS) significantly improved the sintered density for the Ti-10%Ni composition, when sintered at l100°C. A eutectic microstructure (CP-Ti + Ti2Ni), coupled with grains of CP-Ti, were identified as the principal phases present. On the other hand, the Ti-Sn alloys only showed a modest increase in sintered density compared to the CP-Ti, owing to the high solubility of Sn in Ti. In terms of crystal structure, XRD highlighted that the Sn containing samples were fully CP-Ti.

Les solides divisés telles que les poudres pharmaceutiques nécessitent souvent des processus d'agrandissement de taille par agglomération pour améliorer leur comportement mécanique, notamment la coulabilité. Pour cette raison, le procédé de "granulation en voie sèche" est utilisé dans l'industrie pharmaceutique. Le procédé consiste à comprimer la poudre en la faisant passer entre deux rouleaux séparés par un entrefer, pour produire des plaquettes qui sont ensuite broyées en granulés et comprimés en compacts. Dans ce procédé, l'existence de différents modèles de compacteurs à rouleaux et de systèmes de broyage d’une part, et l'interaction entre les paramètres des procédés et des propriétés des produits (plaquettes, granulés et comprimés) d’autre part, rendent difficile la compréhension des phénomènes et des mécanismes sous-jacents. En particulier, le procédé entraîne une perte de résistance mécanique des comprimés formés à partir de granulés (comparativement à celles des comprimés de poudres non-granulés) et ce phénomène est encore mal compris. Ces aspects sont étudiés dans ce travail de thèse en menant des caractérisations expérimentales et des modélisations numériques permettant de mieux comprendre les modifications micro et macro structurales des poudres mises en forme par granulation sèche. Le but ultime est de progresser dans la compréhension des relations "propriétés des poudres - paramètres des procédés". Enfin, la compréhension des différences de comportement en compression de poudres granulées et non-granulées est menée à l’aide d’une modélisation du comportement dans le cadre de la mécanique des milieux continus poreux. / Particulate solids such as pharmaceutical powders often require size enlargement processes to improve the manufacturing properties like flowability. For that reason, dry granulation by roll compaction has been widely used in the pharmaceutical industry. The process consists of compressing powders between two counter-rotating rolls to produce ribbons that will be subsequently milled into granules. The obtained granules are tableted for oral dosage. In this process there are two main limitations: the existence of different designs of the roll compactors, milling systems and the interaction between process parameters and raw material properties are still a challenge and the roll-compaction process leads to an inferior tensile strength of tablets compared with direct compression. These aspects are investigated in this work. In the first part of this thesis, an analysis on the effect of different roll-compaction conditions and milling process parameters on ribbons, granules and tablet properties was performed, highlighting the role of the sealing system and the ribbon density distribution characteristics. In the second part, die compaction of roll-compacted powders, as the last stage of the process, is further investigated in terms of experimental analysis (effect of the granule size and composition and stress transmission measurements) and modelling the compaction behavior of granules.