Orientador: Leonardo Lorenzo Bravo Roger / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Tecnologia / Made available in DSpace on 2018-08-26T21:14:03Z (GMT). No. of bitstreams: 1 SantosSouza_GilbertodeTadeu_M.pdf: 4051949 bytes, checksum: 3271a81290629f1d51c661d022a0cbd7 (MD5) Previous issue date: 2015 / Resumo: O projeto e a análise teórico-experimental de uma nova etiqueta sem chip para RFID com comunicação redundante é apresentado. Esta nova etiqueta poderá ser capaz de operar em duas bandas de frequências diferentes para a transmissão da informação binária, aproveitando a utilização em sua concepção de antenas dual-band. A técnica aqui mencionada é clássica, conhecida como diversidade de frequência, mas é utilizada neste trabalho pela primeira vez aplicada em etiquetas chipless de RFID visando aumentar a confiabilidade da comunicação com as leitoras de RFID. Simulações realizadas do novo dispositivo proposto com o software HFSS (High Frequency Structural Simulator) mostraram o seu desempenho adequado. A metodologia do projeto é apresentada passo a passo e os resultados são analisados e discutidos no texto / Abstract: The project and the theoretical-experimental analysis of a new chipless RFID tag with redundant communication is presented. This new tag may be capable to operate in two different frequencies bands for the transmission of binary information, taking advantage of the use in its design of dual-band antennas. The technique mentioned here is classic, known as frequency diversity, but it is used in this work for the first time applied in chipless RFID tags to increase the reliability of the communication with the RFID readers. Simulations of the proposed new device with HFSS (High Frequency Structural Simulator) software showed an adequate performance. The project methodology is presented step by step and the results are analyzed and discussed in the text / Mestrado / Tecnologia e Inovação / Mestre em Tecnologia

ITC/USA 2006 Conference Proceedings / The Forty-Second Annual International Telemetering Conference and Technical Exhibition / October 23-26, 2006 / Town and Country Resort & Convention Center, San Diego, California / In this paper, we propose a dual-band switched beam system operating at 4.05 and 7.4 GHz. This system comprise of a dual frequency Butler matrix feeding a microstrip antenna array. Very good agreement is shown between measured and simulated data. The system can provide a tilted beam of ±13° and ±48° at the lowest frequency band and ±9° and ±27° at the higher frequency band.

International Telemetering Conference Proceedings / October 21, 2002 / Town & Country Hotel and Conference Center, San Diego, California / Recent changes in spectrum availability as well as higher demands for spectrum have motivated the development of telemetry transmit systems capable of fully operating over both L and S telemetry bands. However, enabling operation within these two bands poses new problems in system design. This paper presents a prototype system capable of operating between 1.4 and 2.4 GHz, which supports continuous phase modulation (CPM) waveforms such as pulse code modulation (PCM), frequency modulation (FM), and shaped offset quadrature phase shift keying (SOQPSK). The system architecture is detailed, and the prototype performance is discussed.

A temporally and spatially non-scanning imaging spectrometer covering two separate spectral bands in the visible region using computed tomographic imaging techniques is described. The computed tomographic techniques allow for the construction of a three-dimensional hyperspectral data cube (x, y, λ) from the two-dimensional input in a single frame time. A computer generated holographic dispersive grating is used to disperse the incoming light into several diffraction orders on a focal plane composed of interwoven pixels independently sensitive to the two bands of interest. Separating the input of the two spectral pixel types gives co-registered output between the two bands and overcomes the limitation of overlapping orders. The proof of concept in the visible is presented using a commercially available camera.The lessons learned from the visible system are applied to a dual infrared band imaging spectrometer. Utilizing recent developments in dual band infrared focal planes a dual band imaging spectrometer is designed covering portions of the MWIR and LWIR atmospheric transmission windows. The system design includes the evaluation of recent developments in dual band infrared focal planes, the design and evaluation of the computer generated holographic disperser, and the optical elements in the system.

No description available.

Microstrip antennas are low in profile, light in weight, conformable in structure and are now developed for many applications. The main difficulty of the microstrip antenna is its narrow bandwidth. Several modern applications like satellite communications, remote sensing and multi-function radar systems will find it useful if there is dual band antenna operating from a single aperture. Some applications require covering both transmitting and receiving frequency bands which are spaced apart. Providing multiple antennas to handle multiple frequencies and polarizations becomes especially difficult if the available space is limited as with airborne platforms and submarine periscopes. Dual band operation can be realized from a single feed using slot loaded or stacked microstrip antenna or two separately fed antennas sharing a common aperture. The former design, when used in arrays, has certain limitations like complicated beam forming or diplexing network and difficulty to realize good radiation patterns at both the bands. The second technique provides more flexibility with separate feed system as beams in each frequency band can be controlled independently. Another desirable feature of a dual band antenna is easy adjustability of upper and lower frequency bands. This thesis presents investigation of a new dual band antenna, which is a hybrid of microstrip and waveguide radiating elements. The low band radiator is a Shorted Annular Ring (SAR) microstrip antenna and the high band radiator is an aperture antenna. The hybrid antenna is realized by forming a waveguide radiator in the shorted region of the SAR microstrip antenna. It is shown that the upper to lower frequency ratio can be controlled by the proper choice of various dimensions and dielectric material. Operation in both linear and circular polarization is possible in either band. Moreover, both broadside and conical beams can be generated in either band from this antenna element. Finite Element Method based software, HFSS and Method of Moments based software, FEKO were employed to perform parametric studies of the proposed dual band antenna. The antenna was not tested physically. Therefore, in most cases, both HFSS and FEKO were employed to corroborate the simulation results. / Master of Science

The rise of satellites in Low Earth Orbit (LEO) is causing more terrestrial electromagnetic interference in the important L- and X-band frequencies which are crucial for astronomical observations. This thesis introduces reflectarray design which can serve as a basis for an interference mitigation solution for radio telescopes. In the envisioned application, When the reflectarray is placed around the circumference of an existing radio telescope, it can drive a null into the radio telescopes radiation pattern sidelobe distribution. Since the reflectarray only occupies a small potion of the rim of the paraboloidal main reflector, its presence does not significantly effect the main lobe peak gain. Since Iridium and Starlink are the target mega-constellations, the reflectarray must be dual band. To cover the operational bandwidths of these constellations, the target bandwidth in the L-band (Iridium) is 0.7%, and that in the X-band (Starlink) is 17.1%. This makes the design of the reflectarray challenging as the frequencies are widely separated and the bandwidth in the X-band is wide The work of this thesis marks a first step in this effort. It includes a reflectarray design containing a multi-layer stack consisting of: (1) a grounded substrate, (2) an X-band slot loaded unit cell geometry, (3) a dielectric superstrate, and (4) an L-band layer containing crossed dipoles. The dual band reflectarray is dual linearly polarized to maintain symmetric response. The reflectarray is designed and simulated using full-wave solvers. The results show that the reflectarray designs are capable of pattern shaping at both bands and operate across the required bandwidths. This architecture could serve as a basis for future reflectarrays capable of nulling satellite interference from mega-constellations in observatory applications in the future. / Master of Science / The signal clarity issues stemming from the increasing number of satellites in Low Earth Orbit (LEO), particularly in the vital L- and X-band frequencies essential for global communications and radio astronomy, are the motivation of this thesis. The endeavor concentrates on designing a dual-band dual-polarized reflectarray antenna which may ultimately be used to help mitigate interference in these bands in radio telescopes. The work is focused on the frequency ranges utilized by the major satellite networks Iridium and Starlink, which operate within the L-band (1616-1626.5 MHz) and X-band (10.7-12.7 GHz). Recognizing the significance of these frequencies for global communication and also to radio astronomy, the reflectarray is designed to contribute to a an interference mitigation system which would ultimately allow for coexistence between radio telescopes and communications systems satellites. Targeting bandwidth achievements of 0.7% for the L-band and 17.1% for the X-band, the focus is on nulling interference arising across these frequency bands and thereby increasing the sensitivity of the radio telescope operating amongst these mega-constellations. The thesis documents a multilayered reflectarray antenna, containing a wide-band X-band layer of slot antennas on one layer and an L-band superstrate layer containing crossed dipoles at another, both of which utilize dual linear polarization for symmetric operation. The completed reflectarray can operate simultaneously in both bands. It has been shown in the two papers cited by {ellingson2021sidelobe,budhu2024design} that reflectarrays placed along the rim of radio telescopes main reflector can be used to drive nulls in the sidelobe envelope of its radiation pattern thereby nulling incoming interference. The antenna design of this thesis suggests a possible candidate for these interference mitigation systems where both bands are targeted.

For the new generation wireless communication systems, there is an increasing demand for devices that covers more than one frequency band. This results in a need for wide-band tunable front-ends. The main objective of this study is to use dual band filters in the design of a multi-band front-end. A wide-band low noise amplifier is also required. To accomplish this project, a fixed frequency bandstop filter, a tunable dual-band filter and a wide-band LNA are designed and implemented successfully. The predefined specifications of this front-end include gain, gain flatness, spurious signal rejection, frequency tuning range, noise figure and linearity. Total power dissipation and number of elements are also taken into consideration. Test results of the manufactured front-end are compared with the results of existing single band front-ends. In order to design a good tunable wide-band filter, just tuning its center frequency will not be enough. The noise figure of this dual-band filter will be proportional to its insertion loss if it will be used as a pre-selection filter in front of a LNA. Hence its insertion loss will affect the overall noise figure of the system. If it will be used after the LNA, its linearity will be more important. When a bandpass filter is tuned over wide range of frequencies, its bandwidth varies significantly which leads to a degradation in rejection of the spurious signals. Therefore, there must be a simultaneous control of center frequency, bandwidth and insertion loss while providing enough linearity. In order to accomplish this mission, a filter that has two passbands is designed and implemented. The first passband is tunable between 136MHz and 174MHz while the second one is tunable between 380MHz and 470MHz. Also, the low noise amplifier works properly between 136MHz and 470MHz. As a result, a front-end that covers two bands is obtained.

ITC/USA 2011 Conference Proceedings / The Forty-Seventh Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2011 / Bally's Las Vegas, Las Vegas, Nevada / A novel dual-band S and C band antenna for high-performance autotracking applications is described. The antenna provides simultaneous dual band coverage for targets with circular or linear polarization. A vertex mounted C-band multi-mode common aperture feed is added in a Cassegrain configuration augmenting the existing ViaSat patented [1-4] ESCAN® S-band prime focus feed. A dichroic subreflector is also added allowing simultaneous dual band operation for the prime focus and Cassegrain configurations with minimal interaction. Existing S-band antennas are easily upgraded for dual band capability with only the additions of the vertex mounted C-band feed and dichroic subreflector.

Multi band technology helps in getting multiple operating frequencies using a single microwave device. This thesis presents the design of dual and tri band microwave devices using coupled transmission line structures. Chapter 2 presents the design of a novel dual band transmission line structure using coupled lines. In chapter 3, Design of a dual band branch line coupler and a dual band Wilkinson power divider are proposed using the novel dual band transmission line structure presented in the previous chapter. In chapter 4, Design of a tri band transmission line structure by extending the dual band structure is presented. The Conclusion and future work are presented in chapter 5.