Cette étude a pour missions essentielles de comprendre et d’expliquer comment le passage d’une langue à une autre voire le mélange des deux codes langagiers qui se côtoient au sein de la population de la Guadeloupe, département français d’outre-mer, le français et le créole, peuvent, dans le cadre des échanges médicaux éducatifs, influencer la compréhension des mécanismes de la maladie par le patient, son acceptation et sa gestion.La justification de cette étude tient du constat que la prévalence de cette maladie chronique en Guadeloupe, l’asthme bronchique, est relativement importante, que la prise en charge reste perfectible malgré les recommandations de bonnes pratiques édictées par les sociétés savantes, et que certains patients ont du mal à comprendre les termes utilisés en français par leur médecin lors de l’annonce du diagnostic, ainsi que par les éducateurs chargés de leur apporter les outils de bonne gestion de cette maladie, ce qui n’est pas sans incidents en termes de morbidité et de mortalité.L’auteur décompose sa recherche autour de cinq grands thèmes :- La description du territoire d’étude, sur le plan géographico-climatique, historico-économique, sanitaire et social, la naissance d’une ère culturelle nouvelle générant une langue partagée par plus de 95% de la population et transmise au sein des familles et dans la communauté.- La présentation de l’éducation thérapeutique, démarche considérée par la communauté scientifique comme essentielle pour améliorer la prise en charge du patient et l’autogestion de la maladie, les plans gouvernementaux successifs traitant de cette matière.- L’état des connaissances sur l’asthme bronchique en France, dans le monde et en Guadeloupe plus particulièrement.- L’impact de la langue créole dans le processus de compréhension de la maladie à travers la relation soignant-soigné, et ses conséquences chez les natifs bilingues en termes d’acquisitions des outils d’autogestion en comparaison à l’utilisation du français.- La formulation de propositions de contextualisation didactique, tant en termes de formation des professionnels de santé par la préconisation de l’utilisation de la langue créole, par l’adaptation des outils psychopédagogiques au contexte local, que d’encouragement du patient à utiliser sa langue maternelle dans l’expression de ses ressentis.La recherche montre que la langue créole, utilisée autant au cours de la consultation par le médecin traitant et par le malade que pendant les séances d’éducation thérapeutique par les éducateurs et le public, influence les indicateurs de gestion de cette maladie.En conclusion, l’auteur défend l’hypothèse selon laquelle l’utilisation de la langue créole dans les échanges médicaux éducatifs chez les adolescents asthmatiques bilingues français-créole favoriserait la compréhension des mécanismes de la maladie asthmatique, la prise de conscience de sa gravité et la nécessité de se soigner pour éviter les complications, corollaire d’une bonne qualité de vie. / In Guadeloupe, a French Overseas Territory, the population uses French and Creole linguistic codes. The main goals of this thesis are to understand and to explain how a better use of French and Creole, within the framework of educational medical exchanges, can improve the understanding of the mechanisms of the disease by the patient, its acceptance and its management.The bronchial asthma is a chronic disease, which affects an important part of the Guadeloupian population. In spite of the recommendations promulgated by the medical scholars, the care of the patients can be improved in Guadeloupe. Certain patients have difficulty understanding the terms used in French by their doctor during the announcement of the diagnosis, as well as by the educators in charge of bringing them the tools of good management of this disease what is not without incidents in terms of morbidity and mortality.The author elaborates his research around five main themes:- The thorough description of the space studied in this thesis; the geography of the land, the history of the population, the impact of the economic; the presentation of the social and health care infrastructures; and furthermore the birth of a new cultural era generating a language shared by more than 95 % of the population and passed on within families and communities.- The presentation of the therapeutic education, the approach considered by the scientific community as essential to improve the management of the patient and the self-management of the disease, the successive governmental plans dealing with this subject.- The state of the knowledge on the bronchial asthma in France, in the world and in Guadeloupe more particularly.- The impact of the Creole language in the process of understanding of the disease within the healthcare relationships and its consequences at the bilingual natives in terms of acquisitions of the tools of self-management in comparison to the use of French.- The formulation of proposals of didactic contextualization regarding the training of the healthcare professionals; the recommendation to the healthcare workers to use the Creole language; the adaptation of the psycho-pedagogical tools to the local context; the encouragement to the patients to use their native language in the expression of their feelings.- Researches show that the Creole language used during the consultation by the regular doctor, but also during the educational sessions therapeutics by the educators influence the indicators of management of this disease. In conclusion, the author defends the hypothesis according to which, the use of the Creole language in the educational medical exchanges at the bilingual asthmatic teenagers French-Creole would favor the understanding of the mechanisms of the asthmatic disease, the awareness of its gravity and the necessity of looking after oneself to avoid the complications, corollary of a good quality of life.

Fatores críticos no controle de um sistema elétrico, sem dúvida alguma, são os desafios de manter-se toda a sua estrutura física em plenas condições de operação. A infra-estrutura passiva, materiais e acessórios, devem manter suas propriedades elétricas e mecânicas, minimizados aos impactos da descaracterização por excedentes de correntes elétricas circulantes. Um dos elementos passivos nas redes de distribuição de energia elétrica é motivo deste estudo, sendo o condutor de corrente elétrica, por meio de fios de cobre eletrolíticos – ETP C110 têmpera meio-duro, seção circular, 101% IACS. As condições operacionais dos fios de cobre instalados numa rede estão sujeitos a intensidade da corrente elétrica de trabalho em períodos e eventos diversos; as correntes podem variar desde a mínima corrente de carga, carga média, carga pesada, sobrecarga ou sobrecorrentes por curto circuitos; todos esses eventos são relacionados a difusidade térmica do material, sendo relacionado para cada um deles uma temperatura obtida. No total foram investigadas 6 amostras, sendo 5 delas denotando um evento de intensidade de corrente elétrica, objetivando apontar os resultados das análises realizadas sobre os efeitos da temperatura imposta pela corrente elétrica circulante em fios. As amostras, originadas de produto, “material base” foram caracterizados, em fio de cobre nu rígido de diâmetro de 4,515 mm (≈16,00 mm²), utilizando-se dispositivo gerador de corrente elétrica, produziu-se intensidade da mesma para cada espécime; cinco amostras foram caracterizadas, sendo respectivamente, em 143 Amper (capacidade nominal do fio), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; cada qual denotando um evento com duração de tempo específica, sendo efetuado o monitoramento do gradiente de temperatura, individualmente, obtendo-se como resultado estruturas de material recristalizado, bem como produtos com recozimento severo. Inicialmente foi investigada a composição química percentual do material encruado pelo processo de trefilação do cobre puro ETP, e também a tração unidirecional e obtenção da estrutura metalográfica de todas as amostras, bem como a resistividade/condutibilidade de ambas. / Critical factor in the control of an electrical system, undoubtedly, are the provocation in maintain it all your physical structure in total operation conditions. Static infrastructure, materials and complement, must to maintain it’s electrical and mechanicals proprieties reduced at impacts loss characteristic for excess of electrical current. One of those statics elements in the electrical power distribution system it’s reason this work, being conductor of electrical current, through de electrolytic copper wire – ETP C110 hardness half-hard, cross-section, 101% IACS. Operations conditions of the copper wire installed in network are subjects to intensity of electrical current in cycle and several events; the currents can alter it from current minim, middle, absolute, overload or short circuit; all those events it’s connected to thermal diffusity of material, being connected to each and all a temperature have achieved. In total was investigated six samples, being five indicating an event of intensity of electrical current, intending obtain results of the analyses made with effects of temperature achieved by electrical current in wires. The samples, made of “base material” were characterized, in copper wire, without isolation, hardness half-hard, diameter 4.515mm (≈16,00 mm²), using it electrical current generator device, makes to circulate intensity of electrical current for each sample; five sample was characterized, being respectively, 143 Amper (nominal capacity of product), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; every one denoting an event with specific duration, being made the monitoring temperature rate of change, individually, obtaining as resulted structure of recrystallized material, and too severe annealing. Previously was investigated the percentage chemical composition of hardened material by drawing process of pure copper ETP, and too unidirectional tensile strength and metallography of all sample, and too the resistivity/conductivity in every one.

Fatores críticos no controle de um sistema elétrico, sem dúvida alguma, são os desafios de manter-se toda a sua estrutura física em plenas condições de operação. A infra-estrutura passiva, materiais e acessórios, devem manter suas propriedades elétricas e mecânicas, minimizados aos impactos da descaracterização por excedentes de correntes elétricas circulantes. Um dos elementos passivos nas redes de distribuição de energia elétrica é motivo deste estudo, sendo o condutor de corrente elétrica, por meio de fios de cobre eletrolíticos – ETP C110 têmpera meio-duro, seção circular, 101% IACS. As condições operacionais dos fios de cobre instalados numa rede estão sujeitos a intensidade da corrente elétrica de trabalho em períodos e eventos diversos; as correntes podem variar desde a mínima corrente de carga, carga média, carga pesada, sobrecarga ou sobrecorrentes por curto circuitos; todos esses eventos são relacionados a difusidade térmica do material, sendo relacionado para cada um deles uma temperatura obtida. No total foram investigadas 6 amostras, sendo 5 delas denotando um evento de intensidade de corrente elétrica, objetivando apontar os resultados das análises realizadas sobre os efeitos da temperatura imposta pela corrente elétrica circulante em fios. As amostras, originadas de produto, “material base” foram caracterizados, em fio de cobre nu rígido de diâmetro de 4,515 mm (≈16,00 mm²), utilizando-se dispositivo gerador de corrente elétrica, produziu-se intensidade da mesma para cada espécime; cinco amostras foram caracterizadas, sendo respectivamente, em 143 Amper (capacidade nominal do fio), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; cada qual denotando um evento com duração de tempo específica, sendo efetuado o monitoramento do gradiente de temperatura, individualmente, obtendo-se como resultado estruturas de material recristalizado, bem como produtos com recozimento severo. Inicialmente foi investigada a composição química percentual do material encruado pelo processo de trefilação do cobre puro ETP, e também a tração unidirecional e obtenção da estrutura metalográfica de todas as amostras, bem como a resistividade/condutibilidade de ambas. / Critical factor in the control of an electrical system, undoubtedly, are the provocation in maintain it all your physical structure in total operation conditions. Static infrastructure, materials and complement, must to maintain it’s electrical and mechanicals proprieties reduced at impacts loss characteristic for excess of electrical current. One of those statics elements in the electrical power distribution system it’s reason this work, being conductor of electrical current, through de electrolytic copper wire – ETP C110 hardness half-hard, cross-section, 101% IACS. Operations conditions of the copper wire installed in network are subjects to intensity of electrical current in cycle and several events; the currents can alter it from current minim, middle, absolute, overload or short circuit; all those events it’s connected to thermal diffusity of material, being connected to each and all a temperature have achieved. In total was investigated six samples, being five indicating an event of intensity of electrical current, intending obtain results of the analyses made with effects of temperature achieved by electrical current in wires. The samples, made of “base material” were characterized, in copper wire, without isolation, hardness half-hard, diameter 4.515mm (≈16,00 mm²), using it electrical current generator device, makes to circulate intensity of electrical current for each sample; five sample was characterized, being respectively, 143 Amper (nominal capacity of product), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; every one denoting an event with specific duration, being made the monitoring temperature rate of change, individually, obtaining as resulted structure of recrystallized material, and too severe annealing. Previously was investigated the percentage chemical composition of hardened material by drawing process of pure copper ETP, and too unidirectional tensile strength and metallography of all sample, and too the resistivity/conductivity in every one.

Fatores críticos no controle de um sistema elétrico, sem dúvida alguma, são os desafios de manter-se toda a sua estrutura física em plenas condições de operação. A infra-estrutura passiva, materiais e acessórios, devem manter suas propriedades elétricas e mecânicas, minimizados aos impactos da descaracterização por excedentes de correntes elétricas circulantes. Um dos elementos passivos nas redes de distribuição de energia elétrica é motivo deste estudo, sendo o condutor de corrente elétrica, por meio de fios de cobre eletrolíticos – ETP C110 têmpera meio-duro, seção circular, 101% IACS. As condições operacionais dos fios de cobre instalados numa rede estão sujeitos a intensidade da corrente elétrica de trabalho em períodos e eventos diversos; as correntes podem variar desde a mínima corrente de carga, carga média, carga pesada, sobrecarga ou sobrecorrentes por curto circuitos; todos esses eventos são relacionados a difusidade térmica do material, sendo relacionado para cada um deles uma temperatura obtida. No total foram investigadas 6 amostras, sendo 5 delas denotando um evento de intensidade de corrente elétrica, objetivando apontar os resultados das análises realizadas sobre os efeitos da temperatura imposta pela corrente elétrica circulante em fios. As amostras, originadas de produto, “material base” foram caracterizados, em fio de cobre nu rígido de diâmetro de 4,515 mm (≈16,00 mm²), utilizando-se dispositivo gerador de corrente elétrica, produziu-se intensidade da mesma para cada espécime; cinco amostras foram caracterizadas, sendo respectivamente, em 143 Amper (capacidade nominal do fio), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; cada qual denotando um evento com duração de tempo específica, sendo efetuado o monitoramento do gradiente de temperatura, individualmente, obtendo-se como resultado estruturas de material recristalizado, bem como produtos com recozimento severo. Inicialmente foi investigada a composição química percentual do material encruado pelo processo de trefilação do cobre puro ETP, e também a tração unidirecional e obtenção da estrutura metalográfica de todas as amostras, bem como a resistividade/condutibilidade de ambas. / Critical factor in the control of an electrical system, undoubtedly, are the provocation in maintain it all your physical structure in total operation conditions. Static infrastructure, materials and complement, must to maintain it’s electrical and mechanicals proprieties reduced at impacts loss characteristic for excess of electrical current. One of those statics elements in the electrical power distribution system it’s reason this work, being conductor of electrical current, through de electrolytic copper wire – ETP C110 hardness half-hard, cross-section, 101% IACS. Operations conditions of the copper wire installed in network are subjects to intensity of electrical current in cycle and several events; the currents can alter it from current minim, middle, absolute, overload or short circuit; all those events it’s connected to thermal diffusity of material, being connected to each and all a temperature have achieved. In total was investigated six samples, being five indicating an event of intensity of electrical current, intending obtain results of the analyses made with effects of temperature achieved by electrical current in wires. The samples, made of “base material” were characterized, in copper wire, without isolation, hardness half-hard, diameter 4.515mm (≈16,00 mm²), using it electrical current generator device, makes to circulate intensity of electrical current for each sample; five sample was characterized, being respectively, 143 Amper (nominal capacity of product), 214.5 Amper, 286 Amper, 400 Amper e 700 Amper; every one denoting an event with specific duration, being made the monitoring temperature rate of change, individually, obtaining as resulted structure of recrystallized material, and too severe annealing. Previously was investigated the percentage chemical composition of hardened material by drawing process of pure copper ETP, and too unidirectional tensile strength and metallography of all sample, and too the resistivity/conductivity in every one.

Mission is a central aspect of the Christian faith and much thought is given to the challenge of proclaiming the gospel in a new context or to a different people group (i.e. contextualization). In recent years, a new context has come to the forefront that has been and is being created through technology, namely virtual reality (VR). The purpose of this study is to explore how contextualization, with regards to evangelization, needs to be done in VR. The proposed thesis is that VR provides a new context in which the Christian faith is, or should be, shared in a contextualized way. Although much thought is given to the question of religion in VR, it mostly focuses on the nature of communities online. This study addresses the issue of online evangelization, which has so far received less attention. This doctoral thesis is structured after the empirical-theological praxis cycle of Faix (2007a), and the Policy Delphi Method (PDM) is the research technique used. Through the PDM, a panel of experts from different backgrounds (theologians, sociologists, and practitioners) discussed the various ways in which VR affects evangelization, the way people form their religious identity, and how contextualization could take place. The aim of this research is to contribute to the field of missiology by investigating VR as a new context in which to proclaim the Christian faith. / Christian Spirituality, Church History and Missiology / D. Th.(Missiology)

Mission is a central aspect of the Christian faith and much thought is given to the challenge of proclaiming the gospel in a new context or to a different people group (i.e. contextualization). In recent years, a new context has come to the forefront that has been and is being created through technology, namely virtual reality (VR). The purpose of this study is to explore how contextualization, with regards to evangelization, needs to be done in VR. The proposed thesis is that VR provides a new context in which the Christian faith is, or should be, shared in a contextualized way. Although much thought is given to the question of religion in VR, it mostly focuses on the nature of communities online. This study addresses the issue of online evangelization, which has so far received less attention. This doctoral thesis is structured after the empirical-theological praxis cycle of Faix (2007a), and the Policy Delphi Method (PDM) is the research technique used. Through the PDM, a panel of experts from different backgrounds (theologians, sociologists, and practitioners) discussed the various ways in which VR affects evangelization, the way people form their religious identity, and how contextualization could take place. The aim of this research is to contribute to the field of missiology by investigating VR as a new context in which to proclaim the Christian faith / Christian Spirituality, Church History and Missiology / D. Th. (Missiology)

The enormous rate of increase in waste generation across the world is a serious threat to the future generation, if not handled properly, due to the creation of health hazards and global warming. This was awakened many engineers and researchers to find an appropriate solution for efficient management of waste. The land filling of the waste is the most widely adopted method for its disposal, whose efficiency mainly depends on the engineered barrier system in place. Though possessing many limitations, clay liner solely or along with Geo-membrane is often used to avoid ground and surface water contamination. The thickness of the liner of a given breakthrough time depends on the transport rates of the selected contaminants. To estimate the transport rate of any given contaminant, it is necessary to understand the different migration processes of contaminants through the liner material. It was observed from the literature that, the transport rate of contaminants mainly depends on Dispersion coefficient (D) and Distribution coefficient (K) which are the main contaminant transport parameters. The amount of contaminant transport through the liner system for a desired time period is thus estimated from these contaminant transport parameters using the Advection-Dispersion Equation (ADE). The unregulated open dumps are another cause of serious environmental problem, where the contaminants are free to migrate in any direction through the underground soil. The percolation rate and the accumulation of leachate increase during the rainy season, which picks up more contaminants from the waste and thus the threat of the leachate increases. The leachate normally migrates in vertical and lateral directions, causing contamination of ground and surface water resources, and hence, there is a need to estimate the transport rates of contaminants in the porous media. These transport rates are not only useful for designing barrier systems, but also useful to find a suitable remediation technique for the removal of contaminants from a contaminated site. Thus, determination of transport rate is very important in effective waste management systems. Most of the researchers have obtained the contaminant transport parameters through the column tests to simulate one dimensional flow. Often, it is a lengthy process and there is a need to find an easy and effective method of determining these parameters which can reduce the time and effort. Generally, the metallic contaminants such as Cadmium (Cd), Copper (Cu), Lead (Pb), Mercury (Hg), Nickel (Ni) and Zinc (Zn) which are most hazardous are considered for the contaminant migration studies. In the present study, the transport rates of two heavy metals Copper and Zinc through locally available Black Cotton soil and Red soil were studied. Column experiments were conducted to simulate the field conditions under two types of test conditions i.e., Constant and Decreasing source concentrations. For Black Cotton soil as the hydraulic conductivity was very less and was taking a long time for achieving complete breakthrough, the soil sectioning method was used to get the depth versus concentration. The soil sectioning method involves the determination of pore water concentration of any given contaminant in different sections of the soil column. The depth versus concentration profile can serve as the same purpose as that of complete column test after breakthrough. The column experiments can be done only up to a relative concentration (C/C0) of about 0.2 instead of 0.8 or more. The soil samples were compacted to different densities to know the effect of density on transport parameters. The Black Cotton Soil samples were compacted to 0.76-0.97 times of maximum dry density and Red Soil samples were compacted to 0.81-0.98 times of maximum dry density. The samples were compacted to lesser densities to reduce the experimentation time. The transport parameters for field densities can be determined by setting „Forecast Trend Lines‟ to the density versus dispersion coefficient and density versus distribution coefficient plots. The contaminant transport was modeled by various methods i.e., Analytical, Semi-analytical, Explicit Finite Difference and Implicit Finite Difference methods. These models can be extended to predict the contaminant migration through soil liners constructed with similar soils. During the lifetime of a landfill, it may be subjected to both constant and decreasing source concentration conditions and thus the contaminant transport parameters determined by both constant and decreasing tests will be useful to estimate the optimum thickness of soil liner. The disposal of waste solutions and sludges by industries has led to problems with the contamination of both soil and groundwater. Much research work has not been carried out in the past for the remediation of contaminated soils in India. Thus an attempt has been made to study in detail the different remediation techniques on various contaminated soils. Three heavy metal contaminated soils were studied with two remediation techniques i.e., Soil washing and immobilization. As a case study, Zinc contaminated soil was collected from Hindustan Zinc Limited located near Udaipur in Rajasthan State, India and column leach tests were conducted on this soil with different leaching solutions to study the efficiency of the soil washing technique. The leaching solutions used for removing zinc from this soil were 0.1N HCl, 0.1N EDTA, 0.1N HCl+0.1N EDTA and 0.1N FeCl3. It was found that 0.1N FeCl3 was more efficient to remove zinc from this soil. The removal efficiency was also high with 0.1N HCl+0.1N EDTA solution. The transport rates were determined by matching the theoretical elution curves with experimental elution curves. The contaminant transport for column leach tests was modeled using analytical solution based on the Leaching Mass Ratio approach. These transport rates are useful to estimate the rate of treatment as well as the amount of flushing solution required to remove Zinc knowing the area of contamination and in-situ soil conditions. One of the potential sources of soil and ground water contamination with toxic metal ions is Effluent Treatment Plant sludge (ETP Sludge). The efficiency of soil washing technique was also studied on ETP Sludge using five leaching solutions i.e., distilled water, 0.1N HCl, 0.1N EDTA, 0.1N HCl+0.1N EDTA and 0.1N FeCl3. ETP sludge was collected at a filter press, KIADB industrial area, Doddaballapur, Bangalore. The removal efficiencies of these leaching solutions for removal of different metal ions (Copper, Zinc, Iron, Nickel, Cadmium, Lead and Chromium) were studied. The highest removal efficiencies were observed with 0.1N FeCl3 and 0.1N HCl+0.1N EDTA. The transport rates of different metals were determined which will be useful to estimate the quantity of leaching solution required in the field to remediate this sludge using soil washing technique. Even though soil washing technique is more effective than immobilization, for less permeable soil with more clay content, it is not a cost effective method. In such cases immobilization technique can be used to remediate the contaminated soil. The immobilized metals will not migrate through soil to groundwater and will not give adverse environmental hazards in their treated state. In the present study, immobilization technique was studied on two materials, (i) contaminated soil from open dump and (ii) ETP Sludge. The contaminated soil was collected from an open dump located at the Bingipura dumping yard, Bangalore and was tested for the presence of heavy metal ions. The efficiency of treatment to immobilize the metals was studied with different additives. The chemical agents with which can decrease the solubility product will be effective to immobilize the metal ions. The stabilizing agents used for treating these materials were lime water, NaOH and cement. These stabilizing agents were selected after preliminary batch tests. Since most of the heavy metals in soils become less mobile with increase in pH, the lime water / NaOH was added to the soil/sludge to adjust the pH of the mixture to 7.0, 8.5 and 10.0. The cement: soil ratios used were, 1:100 (pH=6. 8), 1:50 (pH=8. 1) and 1:25 (pH=9. 8) by weight. Leaching tests were conducted on the amended soils to know the long term efficiencies of the chemical agents for immobilizing the metal ions. The work carried out in this thesis is presented in different chapters as given below: For the design of the liner system, it is necessary to know the different contaminant transport processes, the determination of their rates and modeling. For remediation of contaminated soil, it is required to find the suitable remediation technique based on the amount and type of pollutants, the type of soil and other geological conditions. The detailed information about sources of heavy metals, effects of heavy metal contamination on health and the environment, contaminant transport processes, methods of determining transport rates, and different modeling techniques for contaminant transport are explained in Chapter 1. The Background information along with the scope and objectives of this study are presented in this chapter. The extensive review of literature related to column experiments, various solutions to Advection-Dispersion Equation, and different remediation techniques to treat the contaminated soil, is also presented in this chapter. Chapter 2 gives detailed information about various materials and methods used in this study. The characteristics of soils used in the present study and preparation of different chemical solutions were explained. The experimental procedures of batch tests, column tests and soil sectioning to determine the contaminant transport parameters were given in detail. The experimental procedures that are required for assessing the efficiency of soil washing technique i.e., Batch leach tests and column leach tests were also explained. The laboratory assessment of immobilization efficiency through leaching test was explained briefly. The analytical and numerical solutions used for this study were discussed in detail. This chapter also includes a method of prediction of breakthrough curves from the incomplete column test data. The contaminant transport parameters of metal ion Copper in two locally available soils i.e., Black cotton soil and Red soil were determined by various techniques i.e., Analytical (using MATLAB v7 software), semi-analytical (using POLLUTE v7 software), Explicit Finite Difference Method with two software tools (MATLAB v7 and M.S.EXCEL 2010), Implicit Finite Difference method with three schemes (BTCS, UPWIND & CRANK NICOLSON) using two software tools (MATLAB v7 and M.S.EXCEL 2010). Modifications were done in the spreadsheet solution of non-reactive solute available from the literature to incorporate the retardation factor as the solutes used in this study are reactive in nature. These results are presented in Chapter 3. The contaminant transport parameters determined for different test conditions (constant and variable source concentrations) and for different densities of soil are reported in this chapter. Determination of transport rates corresponding to maximum dry density using trend lines and preparation of design charts to estimate the thickness of the liner are also discussed in this chapter. The contaminant transport parameters were also determined for metal ion Zinc in the same soils with the same techniques as that of Copper and the migration rates were compared for both the ions. These models and comparative results are presented Chapter 4. It was observed that with increase in density, the dispersion coefficient decreases and Distribution coefficient increases. It was also found that the dispersion coefficient of Black Cotton Soil was lower than that of Red Soil whereas the distribution coefficient of Black Cotton soil is much higher than that of Red Soil. Further, it was observed that the dispersion coefficient of Copper was less than that of Zinc whereas the distribution coefficient of Copper was higher than Zinc. The design of liner thickness, based on transport rates of Zinc is briefly discussed in this chapter. A case study has been explained for the remediation of Zinc contaminated sandy soil using soil washing technique. The undisturbed soil samples collected from four locations of waste disposal site of Hindustan Zinc Limited located near Udaipur in Rajasthan State of Western India were assessed to find the suitable leaching solution and number of pore volumes for the effective removal of Zinc from this soil. The chelates/ solvents used for this soil were 0.1N HCl, 0.1N EDTA, 0.1N HCl+0.1N EDTA and 0.1N FeCl3. The contaminant transport parameters were also determined from the column leach tests based on the Leaching Mass Ratio approach and the results are presented in Chapter 5. From the experimental study it was observed that 0.1N FeCl3 and 0.1N HCl+0.1N EDTA are the most suitable leaching solutions to treat this soil. The Chapter 6 contains the sludge analysis of an industrial ETP sludge, column leach test results of this sludge with different leaching solutions, removal efficiencies of different solutions used and the transport rates of different contaminants. The leaching solutions used for this sludge were distilled water, 0.1N HCl, 0.1N EDTA, 0.1N HCl+0.1N EDTA and 0.1N FeCl3. It was observed that 0.1N FeCl3 and 0.1N HCl+0.1N EDTA are the most suitable leaching solutions to treat this sludge. Other solutions have also removed the contaminants by more than 50%, but the number of pore volumes required to leach out the contaminants was high. The order of removal efficiencies of different solutions is presented below: 0.1N FeCl3 > 0.1N HCl + 0.1N EDTA > 0.1N EDTA > 0.1N HCl > distilled water. The transport rates of different contaminants (Cu, Zn, Cd, Fe, Ni, Pb and Cr) were determined using analytical solution and are presented in this chapter. These transport rates are useful to estimate the quantity of leaching solution required in the field to remediate the sludge using soil washing technique. A contaminated soil collected from an open dump site within Bangalore city and ETP Sludge were analyzed to know the efficiency of immobilization/ solidification technique of remediation using three chemical agents lime, NaOH and cement. The soil samples were mixed with different proportions of these chemicals to adjust the pH of the mixtures to 7.0, 8.5 and 10.0. Leaching tests were conducted on the modified soils to know the long term efficiency of these chemical agents to immobilize the contaminants and these results are discussed in Chapter7. The results showed that highest immobilization efficiencies can be achieved with lime for this contaminated soil and cement is the most suitable chemical agent to treat this sludge. The immobilization efficiencies of different stabilizing agents for various metals were studied and the results analyzed. The Chapter 8 includes the major observations and conclusions of the present research work which will be useful for Geotechnical and Geo-environmental engineers to estimate the transport rates of contaminants, to design the soil liners, to assess the efficiency of soil washing technique to remediate the contaminated soil, to estimate the quantity of leaching solution required in the field for soil washing and to find the suitable chemical agent for remediating the contaminated soil by immobilization technique.

This study investigates how term structure dynamics of VIX futures can be exploited forabnormal returns. To be able to access volatility as a tradeable asset, the trading strategiesonly trades ETFs which are designed to replicate the movements of VIX futures index. Itis established that such ETFs are unsuitable for buy-and-hold investments because of thenegative roll yield it usually suffers, caused by the slope of the VIX term structure.Consequently, these conditions create opportunities for strategies that use direct andinverse VIX ETFs to be profitable. The study is a quantitative study that uses historicalprice data to back test three different trading strategies. The strategies are tested over theperiod 11-oct-2011 to 31-mar-2020. The authors have deliberately chosen to delimit thestudy by not testing the performance of the ETFs, not statistically test the risk-adjustedreturns and not perform a regression to calculate optimal hedge ratios for the strategies.The results from this study shows that its possible for strategies that exploit the termstructure dynamics of VIX futures to generate abnormal returns.

German text / Die gesellschaftliche Relevanz des diakonischen Handelns eines regionalen deutschen Gemeinschaftsverbandes wird in dieser Forschungsarbeit qualitativ erforscht. Diese explorative Studie soll die Gesellschaftsrelevanz diakonischen Handelns, Entwicklungen diakonischer Praxis und ganz grundlegend das Verständnis von Diakonie in diesem Gemeinschaftsverband erschließen. Nach einer auf praktisch-theologische und kirchengeschichtliche Aspekte fokussierten Einleitung werden mittels des empirisch-theologischen Praxiszyklus sowohl Planung und Durchführung, als auch die Ergebnisse qualitativer Interviews dargestellt. Zehn Experteninterviews waren Teil der Hauptforschung. Unter Anwendung der Grounded Theory ließen sich nach mehreren unterschiedlichen Codiervorgängen sechs Typologien diakonischer Gesellschaftsrelevanz herausarbeiten. Die sechs herausgearbeiteten Typen wurden in einer 3x3-Matrix angeordnet, mit den Koordinaten Diakonische Gesellschaftsrelevanz (minimal - zunehmend - profiliert) und Eschatologie (negativ - neutral - positiv). Impulse zur Weiterentwicklung der diakonischen Grunddimension in diesem Gemeinschaftsverband werden abschließend auf Grundlage der Forschungsergebnisse gegeben. / This research analyses the relevance of diaconal action of a regional German community association in its social environment. The explorative study aims to give insight into the social relevance, developments in diaconal practice and the general understanding of diaconia prevalent in this brethren association. After an introduction focusing on practical theology and church history, the study concentrates on the planning, implementation and results of interviews applying the empirical-theological practice cycle. These interviews with ten experts were part of the main research. Through applying the grounded theory, six typologies of diaconal relevance in society emerged from several coding processes. These types were arranged in a 3x3 matrix showing diaconal relevance for society (minimal – increasing – prominent) and eschatology (negative – neutral – positive) as coordinates. The research results formed the basis of ideas presented for further development of the sphere of diaconal action in this community association. / Practical Theology / M. Th. (Practical Theology)

本研究旨在了解日本學生的語言學習信念變化，並找出哪些因素在台灣和日本的TESOL環境中影響學生的學習信念的形成和變化。不同於傳統基於問卷的調查，只針對某些固定的學生的學習信念特徵的研究，最近的研究更注重學習信念的動態變化過程。社會文化理論還強調，社會文化環境在學生的思考過程中具有中介的效果。本研究旨在了解日本學生的學習信念是如何受他們的學習經驗影響，而這些經驗在不同的環境如何影響他們的學習信念。本研究使用深度訪談收集資料，採用半結構式訪談每個月針對學生的學習經歷和信念進行一學期五次的資料蒐集。通過Liblich(1998)的方法整理出訪談資料的整體與分類的內容，本研究希望找出在台灣和日本學習語言的意識形態的不同，這些差異和參與者的語言學習信念之關係，以及在台灣的日本學生面臨何種語言學習機會和挑戰。 這項研究的結果是，三位參與者經歷了不同程度的語言學習信念轉變，同時形成新的學習信念。來台灣之前，參與者對於自己的英文能力的自信心高低不一，但他們都相信能夠透過海外留學加強英文能力。在台灣，由台灣以及西方學生所組成的團體使參與者能夠練習英文並表達自己的意見，無須擔心被批評。ETP課程給他們一個機會可以使用英文來學習並溝通。來到台灣一年後，Yoshi對英文能力變得較有自信，且相信策略運用比天生能力來的重要。Taka變得較不在意自己的發音且把注意力放在文化學習上。Ko了解自己天生語言學習能力的極限並開始發展自己的學習策略。在研究建議方面，當未來的研究採用BALLI(Belief About Language Learning Inventory)(Horwitz,1999)分析時也應將親密團體和社會文化等因素加入。在英語教育方面，台灣的大學英語培訓課程應該包括更多的跨文化差異教學，所以當國際學生參加一般ETP(English taught program)時他們將面臨較少的文化衝擊。由於參與者提到與台灣和國際學生的非正式交流對她們的英語學習大有幫助，在ETP課程中教授應考量國際學生的英語水平，並把他們分配在具有相應英語水平的小組中，使他們能夠更快克服學習困難。期望這項研究的結果提供語言教學方法的調整建議，以滿足國際學生，特別是日本學生的需求。 / This study was aimed to understand the language learning belief change of Japanese students, and to find out what are the factors in the TESOL environments of Taiwan and Japan that lead to these changes. Unlike the traditional questionnaire-based research, which studied student’s learning belief based on certain critical characteristics; recent studies focused more on the changing process of language learning belief. Socio-cultural theories also stressed that the socio-cultural environment has meditational effects on the student’s thinking process (Furberg, 2009). This study tried to understand how Japanese student’s English learning belief was affected by their learning experiences and how these experiences in the different environments affected their learning belief reciprocally. This study adopted in-depth interviews to collect data, using semi-structured interviews per month for six months to discover how Japanese students’ learning experiences and belief changed in the process. By analyzing the interview data using the holistic-content method proposed by Liblich et al (1998), this study focused on how different language learning ideologies in Taiwan and Japan affected the participants’ learning belief, what opportunities and challenges the Japanese students faced in Taiwan in terms of language learning. Based on the result of this study, the three participants experienced different degrees of language learning belief changes and formed new learning beliefs in the process. Before they came to Taiwan, the participants had different levels of self-confidence and all believed that they could improve their English proficiency by studying abroad. In Taiwan, the supportive community formed by Taiwanese and Western students allowed the participants to practice English and express their ideas without being afraid of getting judged. The ETP (English Taught Program) offered them an opportunity to use English to both study and communicate on a daily basis. After one year of staying in Taiwan, Yoshi became more confident in his English proficiency and believed more in strategy use than innate language learning ability. Taka was less anxious about his Japanese accent and put more emphasis on learning cultural factors. Ko realized the limitation of his innate language learning ability and began to develop his own language learning strategies. As for theoretical implication, factors like community and socio-cultural influence should be added to BALLI’s (Belief About Language Learning Inventory)(Horwitz,1999) model in analyzing language learning belief in future studies. In terms of pedagogical implication, English training programs in Taiwan’s university should provide more cross-cultural information so that when international students take English taught classes they will encounter less cultural shock. As the participants mentioned that the informal interaction with Taiwanese and Western students assisted their English learning, professors in the ETP classes should consider international students’ English proficiency and put them within groups of appropriate English levels so they can learn with less difficulty.