With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

Non-radiative wireless power transfer using the coupled mode resonance phenomenon has been widely reported in the literature. However, the distance over which such phenomenon exists is very short when measured in terms of wavelength. In this dissertation, how efficient wireless power transfer can be realized in the radiating near-field region beyond the coupled mode resonance region is investigated. First, electrically small folded cylindrical helix (FCH) dipole antennas are designed to achieve efficient near-field power transfer. Measurements show that a 40% power transfer efficiency (PTE) can be realized at the distance of 0.25λ between two antennas in the co-linear configuration. These values come very close to the theoretical upper bound derived based on the spherical mode theory. The results also highlight the importance of antenna radiation efficiency and impedance matching in achieving efficient wireless power transfer. Second, antenna diversity is explored to further extend the range or efficiency of the power transfer. For transmitter diversity, it is found that a stable PTE region can be created when multiple transmitters are employed at sufficiently close spacing. For receiver diversity, it is found that the overall PTE can be improved as the number of the receivers is increased. Third, small directive antennas are investigated as a means of enhancing near-field wireless power transfer. Small directive antennas based on the FCH design are also implemented to enhance the PTE. It is shown that the far-field realized gain is a good surrogate for designing small directive antennas for near-field power transfer. Fourth, to examine the effects of surrounding environments on near-field coupling, an upper bound for near-field wireless power transfer is derived when a transmitter and a received are separated by a spherical material shell. The derived PTE bounds are verified using full-wave electromagnetic simulation and show good agreement for both TM mode and TE mode radiators. Using the derived theory, lossy dielectric material effects on wireless power transfer are studied. Power transfer measurements through walls are also reported and compared with the theory. Lastly, electrically small circularly polarized antennas are investigated as a means of alleviating orientation dependence in near-field wireless power transfer. An electrically small turnstile dipole antenna is designed by utilizing top loading and multiple folding. The circularly polarization characteristic of the design is first tested in the far field, before the antennas are placed in the radiating near-field region for wireless power transfer. It is shown that such circularly polarized antennas can lessen orientation dependence in near-field coupling. / text

ITC/USA 2013 Conference Proceedings / The Forty-Ninth Annual International Telemetering Conference and Technical Exhibition / October 21-24, 2013 / Bally's Hotel & Convention Center, Las Vegas, NV / In this paper, a new technique utilizing a scatterer of high dielectric constant in between electrically small antennas to achieve good Direction of arrival (DOA) estimation performance is demonstrated. The phase information of the received signal at the antennas is utilized for direction estimation. The impact of the property of the scatterer on the directional sensitivity and the output signal to noise ratio (SNR) level are studied. Finally the DOA estimation accuracy is analyzed with the proposed technique under the consumption of white Gaussian noise environment.

ITC/USA 2012 Conference Proceedings / The Forty-Eighth Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2012 / Town and Country Resort & Convention Center, San Diego, California / There are always some intrinsic tradeoffs among the performance characteristics: radiation efficiency, directivity, and bandwidth, of electrically small antennas (ESAs). A non-Foster enhanced, broad bandwidth, metamaterial-inspired, electrically small, Egyptian axe dipole (EAD) antenna has been successfully designed and measured to overcome two of these restrictions. By incorporating a non-Foster circuit internally in the near-field resonant parasitic (NFRP) element, the bandwidth of the resulting electrically small antenna was enhanced significantly. The measured results show that the 10 dB bandwidth (BW10dB) of the non-Foster circuit-augmented EAD antenna is more than 6 times the original BW10dB value of the corresponding passive EAD antenna.

Electrically conductive adhesives (ECA) are discussed and studied with everincreasing interest as an environmentally friendly alternative to solder interconnection in microelectronics circuit packaging. They are used to attach surface mount devices (SMD), Integrated Circuits (IC) and Flip chips in electronic assembly. The use of ECAs brings some benefits like flexibility, mild processing conditions and process simplicity. Multi walled carbon nanotubes (MWCNT) are used instead of metal fillers because of their novel properties such as light weight, high aspect ratio, corrosion resistant, reduced processing temperature, lead free, good electrical conduction and mechanical strength. The purpose of the present work is to investigate the aging behavior of MWCNT filled adhesives based on anhydride cured epoxy systems and their dependence on loading. Composites with different loadings of MWNT in epoxy and epoxy: heloxy are prepared and then stencil printed onto different surface finished boards like gold, silver and tin to prepare contact resistance samples and onto aluminum oxide boards to prepare volume resistivity samples. These samples are kept at room temperature for about 90 days and then placed in a temperature chamber to observe the behavior of these samples after accelerated aging. The readings are taken for as prepared samples, after 45 days, after 90 days and after accelerated aging. The results are summarized and different trends are observed for different loadings of MWNT, different combinations of epoxy: heloxy and for different surface finished boards.

With the increasing demand for high performance communication networks and the proliferation of mobile devices, significant advances in antenna design are essential. In recent years the rising demands of the mobile wireless communication industry have forced antennas to have increased performance while being limited to an ever decreasing footprint. Such design constraints have forced antenna designers to consider frequency agile antennas so that their behavior can adapt with changing system requirements or environmental conditions. Frequency agile antennas used for mobile handset applications must also be inexpensive, robust, and make use of electronic switching with reasonable DC power consumption. Previous works have addressed a number of these requirements but relatively little work has been performed on frequency agile dielectric resonator antennas (DRAs). The objective of this thesis is to investigate the use of DRAs for frequency reconfigurability. DRAs are an attractive option due to their compactness, very low losses leading to high radiation efficiencies (better than 95%) and fairly wide bandwidths compared to alternatives. DRA’s are also well suited for mobile communications since they can be placed on a ground plane and are by nature low gain antennas whose radiation patterns typically resemble those of short electric or magnetic dipoles. One way to electronically reconfigure a DRA, in the sense of altering the frequency band over which the input reflection coefficient of the antenna is below some threshold, is to partially load one face of the DRA with a conducting surface. By altering the way in which this surface connects to the groundplane on which the DRA is mounted, the DRA can be reconfigured due to changes in its mode structure. This connection was first made using several conducting tabs which resulted in a tuning range of 69% while having poor cross polarization performance. In order to address the poor cross polarization performance a second conducting surface was placed on the opposing DRA wall. This technique significantly reduced the cross polarization levels while obtaining a tuning range of 83%. The dual-wall conductively loaded DRA was then extended to include a full electronic implementation using PIN diodes and varactor diodes in order to achieve discrete and continuous tuning respectively. The two techniques both achieved discrete tuning ranges of 95% while the varactor implementation also had a continuous tuning range of 59% while both maintaining an acceptable cross polarization level.

The main focus of the work presented in this thesis concerns the development and improvement of Wireless Sensor Networks (WSNs) as well as Wireless Body Area Networks (WBANs). WSN consist of interlinked, wireless devices (nodes) capable of relaying data wirelessly between the nodes. The applications of WSNs are very broad and cover both wireless fitness monitoring systems such as pulse watches or wireless temperature monitoring of buildings, among others. The topics investigated in the work presented within this thesis covers antenna design, wireless propagation environment evaluation and modeling, adaptive antenna control and wireless nodes system design and evaluation. In order to provide an end-user suitable solution for wireless nodes the devices require both small form factor and good performance in order to be competitive on the marked and thus the main part of this thesis focuses on techniques developed and data collected to help achieve these goals.  Several different prototype systems have been developed which have been used to measure data by the Swedish Defence Research Agency (FOI), GKN Aerospace Sweden AB, the Swedish Transport Administration. The system developed with GKN Aerospace was used to do real-time test measurements inside a running RM12 jet engine and required a substantial amount of measurements, environmental modeling and system validation in order to properly design a wireless system suitable for the harsh and fast fading environment inside a jet engine. For FOI improvements were made on a wearable wireless body area network initially developed during the authors master thesis work. Refinements included work on new generation wireless nodes, antenna packaging and node-supported diversity techniques. Work and papers regarding the design of different types of antennas suitable for wireless nodes are presented. The primary constraints on the presented antennas are the limited electrical size. The types of antennas developed include electrically small helix antennas manufactured both on stretchable substrates consisting of a PDMS substrate with Galinstan as the liquid metal conductors, screen printed silver ink for helix antennas and conformal dual patch antennas for wireless sensor nodes. Other standard type antennas are included on the wireless sensors as well.

When an electrically small antenna is conceived, designed, simulated, and tested, the main emphasis is usually placed immediately on its impedance bandwidth and radiation efficiency. All too often it is assumed that its directivity will only be that of a Hertzian dipole and, hence, its directivity becomes a minor consideration. This is particularly true if such a compact antenna radiates in the presence of a large ground plane. Attention is typically focused on the radiator and its size, while the ground plane is forgotten. This has become a too frequent occurrence when antennas, such as patch antennas that have been augmented with metamaterial structures, are explored. In this paper, it is demonstrated that while the ground plane has little impact on the resonance frequency and impedance bandwidth of patch antennas or metamaterial-inspired three-dimensional magnetic EZ antennas, it has a huge impact on their directivity performance. Moreover, it is demonstrated that with both a metamaterial-inspired two-element array and a related Huygens dipole antenna, one can achieve broadside-radiating electrically small systems that have high directivities. Several common and original designs are used to highlight these issues and to emphasize why a fundamental figure of merit such as directivity should never be overlooked.

No description available.

During this project we have designed a new type of antenna that uses an array of antenna elements in order to emit electromagnetic radiation as signals and to be able to control the beam. After an extended time the design yielded a simulation which had the correct characteristics. After printing and constructing a prototype of the antenna it was tested in an anechoic chamber at Uppsala University. The array was divided into two different sub-arrays: the upper and the lower sub-arrays. Each of these consisted in itself of two sides: the long and the short sides. Each side had seven radiating elements, during the tests only one of the two sub-arrays (upper or lower) was running. Both sub-arrays are excited via a rat-race or 90 degree coupler. While the antenna was running it had 14 radiating elements and two phase shifters, two per sub-array and two per side. The idea was for a signal to travel passing the radiating elements and the phase shifter which would steer the induced electromagnetic signal in one direction, a traveling-wave array. This direction could be changed since the phase shifters were configurable in three different states per phase shifter, hence the induced electromagnetic beam was steerable. The beam was also steerable through the feed which was re-configurable, since there were two feeds per sub-array a phase shift could be introduced between the long and the short side. The beam steering range was between -2 degrees and 11 degrees oriented as 0 degrees would be a perpendicular line from the array to the receiving end. The design itself worked which could be stated from the results in the upper part of the array, the test results from the lower part however did not match the simulated results. This is likely due to an error in the construction of the antenna rather than the theory since the upper and lower part of the array was mirrored versions of each other. The phase shifters worked as intended in the bigger picture but were slightly different in the simulations compared to the physical ones, likely due to the same type of error source as regarding the full antenna.