The biggest scientific experiment in history will begin taking data in late 2009 using the Large Hadron Collider (LHC) at CERN near Geneva, Switzerland. The LHC is designed to collide protons at an unprecedented 14 TeV centre of mass energy, enabling physicists to explore the constituents of matter at smaller scales than ever before. The Parton Distribution Functions (PDFs) are parametrizations of the proton structure and are best determined from experimental data. The PDFs are needed to calculate cross-sections or in other words the likelihood of observed physical processes, which are crucial in exploiting the discovery potential of the LHC. The prospects for measuring the Drell-Yan (DY) spectrum are assessed in the low invariant mass region below the Z boson resonance using e+e− pairs from the initial LHC data in order to probe the proton structure and further constrain the PDFs. The analysis is based on the full simulation of the ATLAS detector response to DY electrons and background processes. Assuming 100 pb−1 of LHC data, the total DY crosssection in the invariant mass range from 10 GeV to 60 GeV is expected to be measured as DY = 5.90±0.24(stat)±0.18(syst) nb. The result predicts an improvement over a current theoretical uncertainty of 7.6% and indicates that the PDF uncertainties can be reduced significantly with the early LHC data.

<p>When the material or geometry of a reactor varies with time, the neutron flux will respond in the form of a reactor transient. These transients can occur during normal operations when control rods are moved or the reactor is refuelled (CANDU). During a reactor accident, the transient response is especially important because the reactor properties vary quickly with large amplitudes. Therefore, better understanding these conditions allows for improved identification, prevention and mitigation of reactor transients. However, current nuclear simulation codes are generally limited in their ability to model transient behaviour.</p> <p>The NStable code was created to model time-dependent neutron populations in multiplying mediums using the Geant4 Monte Carlo toolkit. The neutron population is allowed to evolve in time, but is periodically renormalized so that the total number of neutrons is constrained within a manageable range. This ensures that the simulation is viable even in highly sub- or supercritical environments. Since Geant4 was not intrinsically designed to track a neutron population over "long" time periods (up to 10 s), the population renormalization mechanisms needed to be created and integrated with Geant4. Additionally, nuclear reactor analysis functionality was added to calculate important quantities such as k_eff.</p> <p>The NStable code was validated using three established nuclear simulation codes: MCNP 5, DRAGON 3.06J, and TART 2005. The validation cases compared spatial distributions and criticality estimates for either homogeneous spheres (uranium-235 or a uranium-heavy water mixture) or the standard CANDU 6 lattice cell. For all three systems, the criticality estimates in NStable agreed with the appropriate validation code within 10 mk (TART for the spheres and DRAGON for the CANDU 6 lattice). Finally, the NStable code was also used to simulate a temperature transient in a UHW sphere where the temperature linear increased by 700 K over 50 ms. In response to the increasing temperature, k_eff decreased by 100 mk over the same period. In the future, transient modelling in NStable should be investigated further to reproduce actual experimental results, and to couple NStable with a thermohydraulics code to simulate a full transient response.</p> / Master of Applied Science (MASc)

<p>Position sensitive detectors represent a class of particle detectors widely used in high-energy physics, astrophysics, biophysics and medicine for imaging the spatial distribution of various radioactive sources. In recent years, a new class of gas based detectors, so-called micropattern gas detectors (MPGDs), has emerged. While modern MPGDs rival solid state detectors in terms of spatial and temporal resolution, their cost of production is significantly lower. A Thick Gaseous Electron Multiplier (THGEM) imaging detector, with a two-dimensional delay line readout, has been constructed as a concept for a large area imaging detector with reasonable spatial resolution. The delay line based THGEM imaging detector is robust, easy to manufacture and cost effective alternative to direct readout techniques which frequently employ a large number of channels. Featuring an active area of 40 x 40 mm<strong>2</strong>, the prototype has been constructed using two 0.4 mm THGEMs and successfully operated in a low pressure, propane based, gas mixture. Two sets of orthogonal electrodes, connected to individual delay lines, serve as a two-dimensional anode readout. Adjacent electrodes are separated by approximately 3.4 ns of time delay and allow the interaction position to be calculated by measuring the time difference between delay line output signals corresponding to a common axis. Using modern field programmable gate arrays (FPGAs), a time-to-digital (TDC) data acquisition (DAQ) system has been developed. The TDC DAQ performs the position reconstruction algorithm and is capable of continuous event rates up to 1.8 MHz. The imaging capabilities of the detector have been assessed using a collimated alpha source and a wide X-ray beam. Under these aforementioned conditions, the detector was able to successfully resolve 1 mm diameter holes spaced 3 mm apart. With higher operating pressures, and using Xenon based gas mixture, it is expected the imaging detector should achieve sub-mm spatial resolution. The investigations presented in this thesis serve as a framework for the development of future THGEM imaging detectors.</p> / Doctor of Philosophy (PhD)

The current state of a prototype fan-beam optical computed tomography scanner for three-dimensional radiation dosimetry has been presented. The system uses a helium-neon laser and a line-generating lens for fan-beam creation. Five photodiode arrays form an approximate arc detector array of 320-elements. Two options of physical collimators provide two levels of scatter-rejection: single-slot (SS) and multi-hole (MH). A pair of linear polarizers has been introduced as a means of light intensity modulation. This work examined: (i) the characterization of system components, (ii) data acquisition & imaging protocols, and (iii) the scanning of an nPAG dosimeter. (i): The polarizer-pair method of light intensity modulation has been calibrated and the polarization sensitivity of the detector array was evaluated. The relationship between detected values and both light intensity and photodiode integration time was examined. This examination indicated the need for an offset correction to treat all data acquired by the system. Data corruption near the edges of each photodiode array was found to cause ring artefacts in image reconstructions. Two methods of extending the dynamic range of the system---via integration time and light intensity---were presented. The use of master absorbent solutions and spectrophotometric data allowed for the preparation of absorption-based and scatter-based samples of known opacities. This ability allowed for the evaluation of the relative scatter-rejection capabilities of the system's two collimators. The MH collimator accurately measured highly-attenuating solutions of both absorption-based and scatter-based agents. The SS collimator experienced some contamination by scattered light with absorption-based agents, and significant contamination with scatter-based agents. Also, using the SS collimator, a `spiking' artefact was observed in highly-attenuating samples of both solution types. (ii): A change in imaging protocol has been described that greatly reduces ring artefacts that plagued the system previously. Scanning parameters related to the reference scan (Io) and data acquisition were evaluated with respect to image noise. Variations in flask imperfections were found to be a significant source of noise. (iii): An nPAG dosimeter was prepared, planned for, irradiated, and imaged using the fan-beam system. In addition to ring artefacts caused by data-corruption, refractive inhomogeneities and particulates in the gelatin were found to cause errors in image reconstructions. Otherwise, contour and percent depth dose comparisons between measured and expected values showed good agreement. Findings have indicated that significant imaging gains may be achieved by performing pre-irradiation and post-irradiation scans of dosimeters.

<p>Solar electricity is a promising energy technology for the future, and by using reflectors for concentrating solar radiation onto photovoltaic cells, the cost per produced kWh can be significantly reduced. The optical efficiency of a concentrating system determines the fraction of the incident energy that is transferred to the cells and depends on the optical properties of the system components. In this thesis, low-concentrating photovoltaic and photovoltaic-thermal systems with two-dimensional parabolic reflectors were studied and optimised, and a new biaxial model for the incidence angle dependence of the optical efficiency was proposed.</p><p>Concentration of light generally results in high cell temperatures, and the uneven irradiance distribution on cells with parabolic reflectors leads to high local currents and temperatures, which reduce fill-factor and voltage. Cooling the cells by means of water increases the voltage and makes it possible to utilize the thermal energy. The performance of a 4X concentrating photovoltaic-thermal system was evaluated. If operated at 50°C, this system would produce 250 kWh_electrical and 800 kWh_thermal per m² cell area and year. Optical performance can be increased by 20% by using better reflectors and anti-reflectance glazing.</p><p>Low-concentrating photovoltaic systems for façade-integration were studied and optimised for maximum annual electricity production. The optimisation was based on measured short-circuit currents versus solar altitude. Measurements were performed outdoors and in a solar simulator. It was found that the use of 3X parabolic reflectors increases the annual electricity production by more than 40%. High solar reflectance is crucial to system performance but by using a low-angle scattering reflector, the fill-factor and power are increased due to a more even irradiance on the modules.</p><p>Long-term system performance depends on the durability of the components. The optical properties and degradation of reflector materials were assessed using spectrophotometry, angular resolved scatterometry, Fresnel modelling, optical microscopy, and surface profilometry before and after ageing. The degradation of reflectors was found to be strongly dependent on material composition and environmental conditions. Back surface mirrors, all-metal reflectors, and polymer-metal laminates degraded in different ways, and therefore accelerated ageing must be tailored for testing of different types of reflector materials. However, new types of reflector laminates showed a potential for increasing the cost-effectiveness of low-concentrating solar energy systems.</p>

This thesis presents experimental and modelling research on atmospheric pressure hollow cathodes and hollow electrodes. Experiments with the hybrid hollow electrode activated discharge (H-HEAD), which is a combination of a hollow cathode and a microwave plasma source, is presented. The experiments show that this source is able to produce long plasma columns in air and nitrogen at atmospheric pressure and at very low gas flow rates. Measurements of the vibrational temperature of the nitrogen molecules are also presented in this thesis. The vibrational temperature is an indication of the electron temperature in the plasma, an important characteristic of the plasma. Modelling work on the hollow cathode at atmospheric pressure with fluid equations is also presented. It is shown that the inclusion of fast and secondary electrons, characteristic of the hollow cathode plasmas, increases the sheath width. The sheath width was found to be of the order of 100 μm. By modelling the plasma as highly collisional by using the drift-diffusion approximation, it was shown that the increase in sheath thickness was larger at lower pressures than at higher pressures. Still, the sheath width can be of the order of 100 μm. A pulsed atmospheric plasma in a hollow electrode geometry was also modelled by the drift-diffusion fluid equations, with the addition of the energy equation for electrons. Rate and transport coefficients for the electrons were calculated from the solution to the Boltzmann equation as functions of mean electron energy. The dynamics of the plasma at pulse rise time showed large electron density and mean energy peaks at the cathode ends, but also that these quantities were enhanced at the centre of the discharge, between the cathode plates.

A parallel finite element code with adaptive meshing was developed and used to study three dimensional, time-dependent fluid flows caused by thermocapillary convection as well as temperature and dopant distribution in fusion welding and floating zone crystal growth. A comprehensive numerical model of the three dimensional time-dependent fluid flows in a weld pool had been developed. This model considered most of the physical mechanisms involved in gas tungsten arc welding. The model helped obtaining the actual chaotic time-dependent melt flow. It was found that the fluid flow in the weld pool was highly complex and influenced the weld pool’s depth and width. The physicochemical model had also been studied and applied numerically in order to simulate the surfactant adsorption onto the surface effect to the surface tension of the metal liquid in a weld pool. Another model, a three dimensional time-dependent, with adaptive mesh refinement and coarsening was applied for simulating the effect of weak flow on the radial segregation in floating zone crystal growth. The phase change equation was also included in this model in order to simulate the real interface shape of floating zone. In the new parallel code, a scheme that keeps the level of node and face instead of the complete history of refinements was utilized to facilitate derefinement. The information was now local and the exchange of information between each and every processor during the derefinement process was minimized. This scheme helped to improve the efficiency of the parallel adaptive solver. / QC 20100527

Flexible printed circuit boards (flex PCBs) are used in a wide range of electronic devices today due to their light weight, bendability, extensive wiring possibilities, and low-cost manufacturing techniques. The general trend in the flex PCB industry is further miniaturization alongside increasing functionality per device and reduced costs. To meet these demands, a new generation of low cost manufacturing technologies is being developed to enable structures with smaller lateral dimensions and higher packing densities. Wet etching is today the most cost-efficient method for producing a large number of through-foil structures in flex PCBs. However, conventional wet etch techniques do not allow for through-foil structures with aspect ratios over 1 – a fact that either necessitates thin and mechanically weak foils or puts severe limitations on the packing density. The fabrication techniques presented in this thesis allow for through-foil structures with higher aspect ratios and packing densities using wet etching. To achieve high aspect ratios with wet etching, the flex PCB foils are pre-treated with irradiation by swift heavy ions. Each ion that passes through the foil leaves a track of damaged material which can be subsequently etched to form highly vertical pores. By using conventional flex PCB process techniques on the porous foils, high aspect ratio metallized through-foil structures are demonstrated. The resulting structures consist of multiple sub-micrometer sized wires. These structures are superior to their conventional counterparts when it comes to their higher aspect ratios, higher possible packing densities and low metallic cross-section. Furthermore, metallized through-foil structures with larger areas and more complicated geometries are possible without losing the mechanical stability of the foil. This in turn enables applications that are not possible using conventional techniques and structures. In this thesis, two such applications are demonstrated: flex PCB vertical thermopile sensors and substrate integrated waveguides for use in millimeter wave applications. / wisenet

Solar electricity is a promising energy technology for the future, and by using reflectors for concentrating solar radiation onto photovoltaic cells, the cost per produced kWh can be significantly reduced. The optical efficiency of a concentrating system determines the fraction of the incident energy that is transferred to the cells and depends on the optical properties of the system components. In this thesis, low-concentrating photovoltaic and photovoltaic-thermal systems with two-dimensional parabolic reflectors were studied and optimised, and a new biaxial model for the incidence angle dependence of the optical efficiency was proposed. Concentration of light generally results in high cell temperatures, and the uneven irradiance distribution on cells with parabolic reflectors leads to high local currents and temperatures, which reduce fill-factor and voltage. Cooling the cells by means of water increases the voltage and makes it possible to utilize the thermal energy. The performance of a 4X concentrating photovoltaic-thermal system was evaluated. If operated at 50°C, this system would produce 250 kWhelectrical and 800 kWhthermal per m2 cell area and year. Optical performance can be increased by 20% by using better reflectors and anti-reflectance glazing. Low-concentrating photovoltaic systems for façade-integration were studied and optimised for maximum annual electricity production. The optimisation was based on measured short-circuit currents versus solar altitude. Measurements were performed outdoors and in a solar simulator. It was found that the use of 3X parabolic reflectors increases the annual electricity production by more than 40%. High solar reflectance is crucial to system performance but by using a low-angle scattering reflector, the fill-factor and power are increased due to a more even irradiance on the modules. Long-term system performance depends on the durability of the components. The optical properties and degradation of reflector materials were assessed using spectrophotometry, angular resolved scatterometry, Fresnel modelling, optical microscopy, and surface profilometry before and after ageing. The degradation of reflectors was found to be strongly dependent on material composition and environmental conditions. Back surface mirrors, all-metal reflectors, and polymer-metal laminates degraded in different ways, and therefore accelerated ageing must be tailored for testing of different types of reflector materials. However, new types of reflector laminates showed a potential for increasing the cost-effectiveness of low-concentrating solar energy systems.

<p>This thesis is devoted to the study of neutrino physics in general and the study of neutrino mixing and oscillations in particular. In the standard model of particle physics, neutrinos are massless, and as a result, they do not mix or oscillate. However, many experimental results now seem to give evidence for neutrino oscillations, and thus, the standard model has to be extended in order to incorporate neutrino masses and mixing among different neutrino flavors.</p><p>When neutrinos propagate through matter, the neutrino mixing, and thus, also the neutrino oscillations, may be significantly altered. While the matter effects may be easily studied in a framework with only two neutrino flavors and constant matter density, we know that there exists (at least) three neutrino flavors and that the matter density of the Universe is far from constant. This thesis includes studies of three-flavor effects and a solution to the two-flavor neutrino oscillation problem in matter with an arbitrary density profile.</p><p>Furthermore, there have historically been attempts to describe the neutrino flavor transitions by other effects than neutrino oscillations. Even if these effects now seem to be disfavored as the leading mechanism, they may still give small corrections to the neutrino oscillation formulas. These effects may lead to erroneous determination of the fundamental neutrino oscillation parameters and are also studied in this thesis in form of damping factors.</p>