Compression strength after impact tests were conducted on unidirectional composite rods with sleeves. These elements represent local members of open three-dimensional composite lattice structures (e.g., based on isogrid or IsoTruss® technologies). The unidirectional cores composed of carbon, glass, or basalt fiber/epoxy composites were co-cured in aramid sleeves. Sleeve patterns included both bi-directional (unsymmetric) braids and unidirectional spiral wraps with sleeve coverage ranging from nominally half to full. The diameters were nominally 8 and 11 mm (5/16 and 7/16 in). The larger diameter had nominally twice the cross-sectional area, to quantify the effects of scaling. The specimens were long enough to encourage local buckling failure as expected in members of typical composite lattice structures. The unsupported lengths varied from 127 mm (5.0 in) to 160 mm (6.3 in). Specimens were radially impacted at mid-length with energy levels ranging from 0 to 20 J (0 to 14.8 ft-lbs) and tested in longitudinal compression to quantify the effects of local impact damage on the buckling strength. In undamaged specimens, sleeve type and sleeve coverage have no effect on the ultimate compression strength of carbon, glass, or basalt composites (7% or less standard deviation for each material). When impacted, the influence of sleeve type and sleeve coverage varies with the type of fiber in the unidirectional core. Sleeve type and coverage did not affect the compression strength after impact for fiberglass composites. On the other hand, both carbon and basalt composites exhibited improved performance with braided (vs. spiral) sleeves (up to 34% stronger) and full (vs. half) coverage (up to 38% stronger). The compression strength of carbon configurations decreases with increasing impact energy regardless of sleeve type or coverage. The higher flexibility of glass and basalt composites, however, allowed some configurations to maintain the same compression strength after impact as their undamaged counterparts, at lower impact energy levels. Doubling cross-sectional area of basalt composites significantly improves the stiffness and compression strength after impact, more than doubling the impact energy required to achieve the same compression strength.

A common method of cancer treatment is radiation therapy. In radiation therapy, a treatment planning system is made to specify the dose of X-rays needed to eradicate the tumor. To assure the right amount of X-ray dosage a quality assurance is using a phantom containing radiation sensors. The sensors are made of semiconductor materials with heavy metal-based contacts. Irradiating heavy elements with a high-intensity beam such as Xrays causes secondary scattering of electrons, resulting in an additional photocurrent which may distort the signal used in the quality analysis. By exchanging the heavy-metal contact material to a lighter version such as a carbon-based material, preventing secondary scattering, the error obtained from the quality analysis can be minimized.In this thesis, characterization of contacts between radiation diodes and a copper substrate by flip-chip bonding with reduced graphene oxide-based anisotropic conducting adhesive is made. The parameters of the connections are characterized with respect to electrical, thermal and mechanical properties.Analysis of the novel contact material is done by comparing different types of graphene-based anisotropic fillers with a commercial metal-based filler. Results obtained indicate that it is possible to exchange the metal-based fillers in an anisotropic conducting adhesive with reduced graphene oxide coated polymer spheres as a contacting material for radiation sensing technology. / En vanlig metod som används för att behandla cancer är strålningsterapi. I strålningsterapi görs ett behandlingsplaneringssystem för att specificera en exakt dos av röntgenstrålning som krävs för att slå ut en tumör. För att säkerställa att man ger rätt dos av röntgenstrålning utförs en kvalitetssäkring genom att använda en fantom innehållande strålningssensorer. Sensorerna är gjorda av halvledarmaterial men har oftast anslutningar gjorda av tunga metalliska material. När man bestrålar metaller med hög intensitet, exempelvis röntgenstrålning, emitteras en sekundär spridning av elektroner i form av en fotoström som kan störa signalen i kvalitetsäkrningen. Genom att byta ut metallen som används i anslutningarna till ett kontaktmaterial med lägre atomnummer som exempelvis kolbaserade material, förhindras den sekundära spridningen av elektroner, som troligtvis minskar felet som uppstår vid kvalitetssäkringen.I detta arbete har en kartläggning av kontakter mellan stålningsdioder och ett kopparsubstrat, genom en flip-chip-bindning process med ett ledande adhesiv baserat på reducerad grafenoxid gjorts. Kontaktparametrarna som kartlagts är baserade på termiska, elektriska och mekaniska egenskaper.Kartläggningen av kontakterna har i mestadels gjort genom att jämföra olika typer av grafen baserade partiklar ett kommersiellt metalbaserat material gjort för flip-chipbindning. Resultaten från arbetet indikerar att det är möjligt att byta ut det metallbaserade partiklarna i ett anisotropt ledande adhesiv med reducerade grafenoxid-belagda polymersfärer som ett ledande material för strålningsapplikationer.

In this study, we propose a multi-walled carbon nanotube epoxy composite sensor for force and pressure sensing in the range of 50 N–2 kN. A manufacturing procedure, including material preparation and deposition techniques, is proposed. The electrode dimensions and the layer thickness were optimized by the finite element method. Temperature compensation is realized by four nanocomposites elements, where only two elements are exposed to the measurand. In order to investigate the influence of the filler contents, samples with different compositions were prepared and investigated. Additionally, the specimens are characterized by cyclical and stepped force/pressure loads or at defined temperatures. The results show that the choice of the filler content should meet a compromise between sensitivity, temperature influence and noise behavior. At constant temperature, a force of at least 50N can be resolved. The measurement error due to the temperature influence is 150N in a temperature range of –20°C–50°C.

Atualmente, a participação da energia elétrica na matriz energética mundial é um assunto em evidência. O estudo do compósito isolante da barra estatórica, um dos componentes principais da máquina hidrogeradora, permite a obtenção de informações físico-químicas relevantes ao aperfeiçoamento do sistema, e também de estudos de comportamento térmico quando este é exposto à alta temperatura, por diferentes intervalos de tempo submetidos a estresses mecânicos, elétricos e/ou químicos. O sistema em estudo é o MICALASTIC®, desenvolvido pela empresa Siemens em 1960. Neste trabalho, as propriedades térmicas do compósito isolante, formado por uma fita de mica, resina epóxi (DGEBA), endurecedor (MHHPA) e acelerador naftenato de zinco (N-Zn) foram estudadas. Utilizando-se as técnicas termoanalíticas Calorimetria Exploratória Diferencial (DSC) e Termogravimetria e Termogravimetria Derivada (TG/DTG), o comportamento térmico de cada um dos materiais foi avaliado. As curvas DSC e TG/DTG também evidenciaram as possíveis interações químicas entre os componentes. Os estudos referentes à cura do material e da degradação térmica do compósito curado foram realizados. Observou-se claramente a influência da quantidade de acelerador na polimerização do sistema. A partir das curvas DSC, observou-se dois mecanismos de cura diferentes coexistentes, um com menor quantidade de N-Zn e outro com concentração maior, resultando em eventos de cura com início em temperaturas diferentes. Esse fato ainda não havia sido estudado desde a origem do sistema. Além disso, a perda de massa referente à evaporação do endurecedor no início do processo de cura foi confirmada a partir da caracterização do compósito por espectroscopia de absorção na região do infravermelho, comparando-se os espectros antes e após o fenômeno. Na prática, dois perfis de impregnação, o Homogêneo e o Heterogêneo, de barras condutoras são utilizados, e uma diferença significativa entre eles foi observada. Os estudos desenvolvidos devem ser associados a testes elétricos específicos para o melhor entendimento da relação entre a aplicação do material e suas propriedades teóricas termoanalíticas. Além disso, foi realizado o estudo cinético da decomposição térmica do compósito curado por métodos termogravimétricos, isotérmico e dinâmico. / Currently, the electric energy participation in the world energy matrix is a significant issue. The insulating composite in stator bars, which are one of the most important components in hydrogenerator machines, allows the attainment of relevant physical and chemical information to system optimization, in addition to study thermal behavior when the material is exposed to high temperatures, for different time intervals and mechanical, chemical and/or electrical stress. The studied system is MICALASTIC®, developed by Siemens Company in 1960. In this work, thermal properties of this insulating composite, composed by mica tape, epoxy resin (DGEBA), hardener (MHHPA) and zinc naphtenate (N-Zn) as accelerator, were studied. Using thermoananalytical techniques as Differential Scanning Calorimetry (DSC) and Thermogravimetry and Derivative Thermogravimetry (TG/DTG), thermal behavior of each material was evaluated. DSC and TG/DTG curves evidenced chemical interactions between components. The study relative to material curing and cured composite thermal degradation were described. It was clearly observed the N-Zn amount influence in the cure of system, and through DSC curves, it was possible to observe two distinct polymerization coexisting mechanisms, one with lower quantity of N-Zn and another one with bigger concentration, resulting in cure events starting in different temperatures. This fact has not been studied yet since the system has been originated. Besides that, the weight loss related to hardener evaporation starting with curing process was confirmed by composite characterization by FTIR spectra, before and after phenomenon. In practice, two impregnation patterns (Homogeneous and Heterogeneous) of conductive bars are used and a significant difference between them was observed. The developed studies have to be associated to electrical tests to a best understanding about material application and theoretical thermoanalytical properties. In addition, it was performed thermal decomposition of cured composite kinetic study by isothermic and dynamic thermogravimetric methods

Atualmente, a participação da energia elétrica na matriz energética mundial é um assunto em evidência. O estudo do compósito isolante da barra estatórica, um dos componentes principais da máquina hidrogeradora, permite a obtenção de informações físico-químicas relevantes ao aperfeiçoamento do sistema, e também de estudos de comportamento térmico quando este é exposto à alta temperatura, por diferentes intervalos de tempo submetidos a estresses mecânicos, elétricos e/ou químicos. O sistema em estudo é o MICALASTIC®, desenvolvido pela empresa Siemens em 1960. Neste trabalho, as propriedades térmicas do compósito isolante, formado por uma fita de mica, resina epóxi (DGEBA), endurecedor (MHHPA) e acelerador naftenato de zinco (N-Zn) foram estudadas. Utilizando-se as técnicas termoanalíticas Calorimetria Exploratória Diferencial (DSC) e Termogravimetria e Termogravimetria Derivada (TG/DTG), o comportamento térmico de cada um dos materiais foi avaliado. As curvas DSC e TG/DTG também evidenciaram as possíveis interações químicas entre os componentes. Os estudos referentes à cura do material e da degradação térmica do compósito curado foram realizados. Observou-se claramente a influência da quantidade de acelerador na polimerização do sistema. A partir das curvas DSC, observou-se dois mecanismos de cura diferentes coexistentes, um com menor quantidade de N-Zn e outro com concentração maior, resultando em eventos de cura com início em temperaturas diferentes. Esse fato ainda não havia sido estudado desde a origem do sistema. Além disso, a perda de massa referente à evaporação do endurecedor no início do processo de cura foi confirmada a partir da caracterização do compósito por espectroscopia de absorção na região do infravermelho, comparando-se os espectros antes e após o fenômeno. Na prática, dois perfis de impregnação, o Homogêneo e o Heterogêneo, de barras condutoras são utilizados, e uma diferença significativa entre eles foi observada. Os estudos desenvolvidos devem ser associados a testes elétricos específicos para o melhor entendimento da relação entre a aplicação do material e suas propriedades teóricas termoanalíticas. Além disso, foi realizado o estudo cinético da decomposição térmica do compósito curado por métodos termogravimétricos, isotérmico e dinâmico. / Currently, the electric energy participation in the world energy matrix is a significant issue. The insulating composite in stator bars, which are one of the most important components in hydrogenerator machines, allows the attainment of relevant physical and chemical information to system optimization, in addition to study thermal behavior when the material is exposed to high temperatures, for different time intervals and mechanical, chemical and/or electrical stress. The studied system is MICALASTIC®, developed by Siemens Company in 1960. In this work, thermal properties of this insulating composite, composed by mica tape, epoxy resin (DGEBA), hardener (MHHPA) and zinc naphtenate (N-Zn) as accelerator, were studied. Using thermoananalytical techniques as Differential Scanning Calorimetry (DSC) and Thermogravimetry and Derivative Thermogravimetry (TG/DTG), thermal behavior of each material was evaluated. DSC and TG/DTG curves evidenced chemical interactions between components. The study relative to material curing and cured composite thermal degradation were described. It was clearly observed the N-Zn amount influence in the cure of system, and through DSC curves, it was possible to observe two distinct polymerization coexisting mechanisms, one with lower quantity of N-Zn and another one with bigger concentration, resulting in cure events starting in different temperatures. This fact has not been studied yet since the system has been originated. Besides that, the weight loss related to hardener evaporation starting with curing process was confirmed by composite characterization by FTIR spectra, before and after phenomenon. In practice, two impregnation patterns (Homogeneous and Heterogeneous) of conductive bars are used and a significant difference between them was observed. The developed studies have to be associated to electrical tests to a best understanding about material application and theoretical thermoanalytical properties. In addition, it was performed thermal decomposition of cured composite kinetic study by isothermic and dynamic thermogravimetric methods

Dans le domaine du renforcement et/ou de la réparation des structures en béton armé par des matériaux composites à l'aide de la méthode du collage extérieur au moyen d'un adhésif époxy, une des préoccupations de la communauté scientifique est l'intégrité structurelle de ce système dans le cas d'incendie dans lequel la haute température est une caractéristique essentielle et peut atteindre jusqu'à 1200°C. Ce travail de recherche est axé sur le comportement thermomécanique à très haute température des matériaux composites [un composite à base de polymère carbone/ époxy (Carbon Fiber Reinforced Polymer- CFRP), un composite textile/ mortier cimentaire (Textile Reinforced Concrete- TRC) et un adhésif à base d'époxy]. L'évolution des propriétés mécaniques et d'autres aspects mécaniques de ces matériaux composites avec la température a été caractérisée. Une nouvelle procédure expérimentale concernant la mesure de la déformation de l'éprouvette à l'aide du capteur laser est développée et validée. Une étude numérique et expérimentale a été réalisée dans le but de déterminer principalement la température à la rupture des joints « composite/ adhésif/ composite » sous les sollicitations mécaniques et thermiques. L'efficacité de la protection thermique de deux isolants [PROMASPRAY®T (produit commercial de la société PROMAT] et Isolant A (produit développé par le LGCIE site Tusset) a aussi été étudiée dans cette thèse. Enfin, une approche numérique, à l'aide du logiciel ANSYS, est utilisée afin de déterminer, de façon préliminaire et approximative, à l'échelle matériau, les propriétés thermiques des matériaux (composite textile/ mortier cimentaire -TRC et Isolant A) / In the area of the strengthening and/or the reparation of reinforced concrete structures with composites by means of the external bonding method using an epoxy adhesive, one of the preoccupation of the scientific community is the structural integrity of this system in the event of fire in which the high temperature is the essential feature et can reach up to 1200°C. This research focuses on the thermo-mechanical behavior of composite materials [carbon/epoxy adhesive composite (or carbon fiber reinforced polymer (CFRP), textile/cementitious mortar composite (or textile reinforced concrete (TRC)] and an epoxy-based adhesive. The evolution of mechanical properties and other mechanical aspects of these materials with the temperature has been characterized. A new experimental procedure concerning the measurement of sample strain by the laser sensor is developed and validated. An experimental and numerical study has been realized in order to mainly determine the temperature at the failure of "composite/adhesive/composite" joints under thermal and mechanical loadings. The effectiveness of the thermal protection of two insulators [PROMASPRAY®T (a commercial product of the PROMAT company and the insulator A (product developed by the LGCIE site Tuset)] has also been investigated in this PhD thesis. Finally, a numerical approach, using ANSYS software, is used to determine, in the preliminary and approximate way, at material scale, thermal properties of the materials [the textile reinforced concrete (TRC) and the insulator A]

In this study, we propose a multi-walled carbon nanotube epoxy composite sensor for force and pressure sensing in the range of 50 N–2 kN. A manufacturing procedure, including material preparation and deposition techniques, is proposed. The electrode dimensions and the layer thickness were optimized by the finite element method. Temperature compensation is realized by four nanocomposites elements, where only two elements are exposed to the measurand. In order to investigate the influence of the filler contents, samples with different compositions were prepared and investigated. Additionally, the specimens are characterized by cyclical and stepped force/pressure loads or at defined temperatures. The results show that the choice of the filler content should meet a compromise between sensitivity, temperature influence and noise behavior. At constant temperature, a force of at least 50N can be resolved. The measurement error due to the temperature influence is 150N in a temperature range of –20°C–50°C.