No description available.

Thesis (M.S.)--Virginia Polytechnic Institute and State University, 1994. / Vita. Abstract. Includes bibliographical references (leaves 67-68). Also available via the Internet.

Techniques for adapting metamaterials for the improvement of RF energy harvesting and infrared photodetection are demonstrated using experimental and computer simulation methods. Two methods for RF energy harvesting are experimentally demonstrated and supported by computer simulation. In the first method, a metamaterial perfect absorber (MPA) is made into a rectenna capable of harvesting RF energy and delivering power to a load by soldering Schottky diodes onto connected split ring resonator (SRR) structures composing the planar metasurface of the perfect absorber. The metamaterial rectenna is accompanied by a ground plane placed parallel to it, which forms a Fabry-Perot cavity between the metasurface and the ground plane. The Fabry-Perot cavity stores energy in the form of standing waves which is transferred to the SRR structures of the metasurface as AC currents that are rectified by the diodes to create DC power. This type of design enables highly efficient energy harvesting for low input power, creates a large antenna capture area, and uses elements with small electrical size, such that 100 uW of power (enough to operate simple devices) can be captured at ambient intensities ~ 1 - 2 uW/cm2. Two designs using this method are presented, one that operates for linear polarizations at 0.9 GHz and a smaller polarization-independent design that operates around 1.5 GHz. In the second method, the energy stored in the standing waves of an MPA Fabry-Perot cavity is instead harvested by placing a separate energy harvesting antenna within the cavity. The cavity shapes and enhances the incident electric field, and then the separate energy harvesting antenna is designed to be inserted into the cavity so that its shape and/or radiation pattern matches the electric field lines within the cavity and maximally extracts the stored energy. This method allows for great customization of antenna design parameters, such as operating frequency, polarization dependence, and directionality, by swapping out different metasurface and antenna designs. Using this method, the amount of power harvested by a simple dipole rectenna placed within a cavity is improved by a factor of 18 as compared to what it would harvest by itself at an ambient intensity of 35 nW/cm2. Lastly, the addition of plasmonic structures to DWELL (quantum dot-in-a-well) infrared photodetectors is investigated by computer simulation. DWELL photodetectors have the potential to one day replace standard mercury cadmium telluride detectors by being cheaper alternatives with a higher operating temperature. The inclusion of gold plasmonic structure arrays into DWELL detectors enables excitation of surface plasmon polariton modes that increase the responsivity of the detector to incident infrared radiation. The peak responsivity of a DWELL detector is demonstrated to improve by a factor of 8 for a 1 um thick layer of plasmonic structures and by a factor of 15 for a 2 um thick layer. These works are steps forward in making RF energy harvesting practically useful and for improving infrared photodetector performance.

There is an increasing need for tuneable spectrally pure semiconductor laser sources as well as broadband and polarization insensitive semiconductor optical amplifiers based on the InGaASP/InP material system, to be monolithically integrated with other active and passive components in a photonic integrated circuit. This thesis aims to contribute to finding a solution through modelling, experimental characterization and design improvements. In this thesis we have analyzed laterally-coupled distributed feedback (LC-DFB) lasers. These lasers have the gratings etched directly out of the ridge sidewalls thus lowering the cost associated with the re-growth process required if the gratings were otherwise embedded above the active region. The performance characteristics are analyzed for the LC-DFB lasers partitioned into 1-, 2-, and 3-, electrodes with individual bias control at various operating temperatures. The laser exhibits a stable single mode emission at 1560 nm with a current tuning rate of ~14 pm/mA for a tuning of 2.25 nm. The side modes are highly suppressed with a maximum side-mode suppression ratio of 58 dB. The light-current characteristics show a minimum 40 mA threshold current, and power saturation occurring at higher injection currents. The linewidth characteristics show a minimum Lorentzian linewidth of 210 kHz under free-running and further linewidth reduction under feedback operation. The multi-electrode LC-DFB laser devices under appropriate and selective driving conditions exhibit a flat frequency modulation response from 0 to above 300 MHz. The multi-electrode configuration can thus be further exploited for certain requirements. Simulation results and design improvements are also presented. The experimental characterization of semiconductor optical amplifier (SOA) and Fabry-Perot (FP) laser operating in the E-band are also presented. For the SOA, the linear vertical and horizontal states of polarization corresponding to the transverse electric (TE) and transverse magnetic (TM) modes were considered. For various input power and bias, performance characteristics shows a peak gain of 21 dBm at 1360 nm, gain bandwidth of 60 nm and polarization sensitivity of under 3 dB obtained for the entire wavelength range analyzed from 1340 to 1440 nm. The analysis presented in this thesis show good results with room for improvement in future designs.

Diploma thesis deals with the construction of a moder semiconductor optical amplifier SOA. In the first chapter optical comunication and the use of optical amplifiers is described. In the next chapter some types of optical fibers, their chemical composition and properties are described in detail. The third chapter overviews optical amplifiers, their use today, describes their advantages and disadvantages and their proper use in optical comunications. The fourth chapter describes the solution of the objective, the right layout of separate blocks and connections used in measurements. Fifth chapter describes used components, describes their basic parameters and proper use in circuit. The last chapter evaluates outputs of measurements and their impact on the objective.

This thesis focuses on the theory, fabrication, and characterization of 2-port surface acoustic wave (SAW) resonators, as well as the application of their Fabry-Pérot resonance modes for strain sensing. The thesis includes three articles. In the first article, a fabrication method for high frequency SAW devices using traditional UV photolithography equipment is developed. It is well known that SAW sensors become more sensitive at higher frequencies but realizing high frequency devices requires small features which challenge existing photolithography methods. The proposed process is a modified version of a previously reported tri-layer lift-off photolithography process intended for Si or SiO2 substrates which allows for compatibility with materials that are piezoelectric and pyroelectric, often used as the substrate in SAW devices. The process uses a lithographic tri-layer consisting of layers of lift-off resist (LOR) on the bottom, back anti-reflection coating (BARC) in the middle, and photoresist (PR) on top, improving resolution by a factor of two over traditional lift-off photolithography techniques. We demonstrate the fabrication of a SAW device with an interdigital transducer (IDT) pitch of 4 μm (minimum feature size of 1 μm) on 128o Y-X cut lithium niobate, whose operating frequency is measured as 994.5 MHz. The 2-Port SAW devices that are used in subsequent chapters are fabricated using this process. The second article proposes a method of analyzing acoustic Fabry-Pérot spectra, by analogy with optical cavities, to determine key SAW parameters. In our experiment, 2-port SAW resonators, consisting of two interdigital transducers (IDTs) laterally separated by a free surface cavity length, are used to generate SAWs on 128o Y-X lithium niobate that are trapped between the two IDTs which also act as Bragg reflectors. Fabry-Pérot cavity peaks can be observed through the electrical S11 (reflection) spectrum measured on one IDT, hence a 2-Port resonator is equivalent to an acoustic Fabry-Pérot cavity/resonator. Measurements of the free spectral range and linewidths are then fitted to linear models to obtain the free surface velocity and attenuation of SAW waves, as well as the reflection of interdigital transducers (IDTs), all of which are crucial design parameters. Our method of analyzing Fabry-Pérot spectra provides a convenient method for determining key characteristics of SAW waves and cavities. In the third article, a surface acoustic wave (SAW) strain sensor based on measuring acoustic Fabry-Pérot resonance peaks from a 2-port SAW resonator is demonstrated. A theoretical analysis is proposed to estimate the frequency sensitivity to strain of IDT and cavity resonances and to predict strain distributions in both the cavity and IDT regions of a 2-port SAW resonator bonded to a tapered cantilever beam. The frequency stability of cavity resonance peaks for fabricated 2-port SAW resonators of different cavity length are measured and analyzed to determine the cavity length which exhibits maximum frequency stability. A cross-correlation analysis technique is then introduced to improve the detection of the frequency shift of SAW resonances and enable multimode frequency shift detection. The measured frequency sensitivity to strain of the cavity resonances of a resonator 10 mm in length (operating frequency = 97.7 MHz) was found to be -103.2 ± 0.2 Hz/με while demonstrating excellent linearity (R2 = 0.9999). By considering a minimum signal to noise ratio (SNR) of 3 dB, the device exhibits a minimum strain resolution of only 234 nε.

Fiber optic temperature sensing has become a well-defined field in the past few decades [1] through the use of Fiber Bragg Gratings, Fabry-Perot interferometry, and pyrometry, to list several techniques in use today.  The use of fiber optics offers significant advantages over electronic sensing in terms of size and insensitivity to harsh conditions such as extreme temperatures and corrosive environments.  The availability of optical sapphire materials, including fibers, has allowed the creation of fiber optic sensing elements able to continuously operate at temperatures of 1600"C [2] or more, thus outstripping the abilities of many commonly used thermocouples (excluding platinum types R, S, and B) [3] which will also exhibit a sensitivity to electromagnetic fields. In addition to the aforementioned benefits, fiber optic sensing techniques provide a great deal of accuracy in temperature measurement over the entire working range of the sensor. The work documented in this thesis consists of efforts to minimize the overall footprint of a sapphire based extrinsic Fabry-Perot interferometry (EFPI) temperature sensing element, as well as strides made in multiplexing the same element and reducing the error potential from cross sensitivity of the thermometer with applied strain.  This work has been variously funded by Pratt & Whitney and the Department of Energy. / Master of Science

京都大学 / 0048 / 新制・課程博士 / 博士(人間健康科学) / 甲第19232号 / 人健博第29号 / 新制||人健||3(附属図書館) / 32231 / 京都大学大学院医学研究科人間健康科学系専攻 / (主査)教授 杉本 直三, 教授 精山 明敏, 教授 戸井 雅和 / 学位規則第4条第1項該当 / Doctor of Human Health Sciences / Kyoto University / DFAM

Intracavity Laser Absorption Spectroscopy (ICLAS) at IR wavelengths offers an opportunity for spectral sensing of low vapor pressure compounds. We report here an ICLAS system design based on a quantum cascade laser (QCL) at THz (69.9 m) and IR wavelengths (9.38 and 8.1 m) with an open external cavity. The sensitivity of such a system is potentially very high due to extraordinarily long effective optical paths that can be achieved in an active cavity. Sensitivity estimation by numerical solution of the laser rate equations for the THz QCL ICLAS system is determined. Experimental development of the external cavity QCL is demonstrated for the two IR wavelengths, as supported by appearance of fine mode structure in the laser spectrum. The 8.1 m wavelength exhibits a dramatic change in the output spectrum caused by the weak intracavity absorption of acetone. Numerical solution of the laser rate equations yields a sensitivity estimation of acetone partial pressure of 165 mTorr corresponding to ~ 200 ppm. The system is also found sensitive to the humidity in the laboratory air with an absorption coefficient of just 3 x 10-7 cm -1 indicating a sensitivity of 111 ppm. Reported also is the design of a compact integrated data acquisition and control system. Potential applications include military and commercial sensing for threat compounds such as explosives, chemical gases, biological aerosols, drugs, banned or invasive organisms, bio-medical breath analysis, and terrestrial or planetary atmospheric science.

A scanning Fabry-Perot transmission filter composed of a pair of dielectric mirrors has been demonstrated at millimeter and sub-millimeter wavelengths. The mirrors are formed by alternating quarter-wave optical thicknesses of silicon and air in the usual Bragg configuration. Detailed theoretical considerations are presented for determining the optimum design including factors that affect achievable finesse. Fundamental loss by lattice and free carrier absorption are considered. High resistivity in the silicon layers was found important for achieving high transmittance and finesse, especially at the longer wavelengths. Also considered are technological factors such as surface roughness, bowing, and misalignment for various proposed manufacturing schemes. Characterization was performed at sub-mm wavelengths using a gas laser together with a Golay cell detector and at millimeter wavelengths using a backward wave oscillator and microwave power meter. A finesse value of 422 for a scanning Fabry-Perot cavity composed of three-period Bragg mirrors was experimentally demonstrated. Finesse values of several thousand are considered to be within reach. This suggests the possibility of a compact terahertz Fabry-Perot spectrometer that can operate in low resonance order to realize high free spectral range while simultaneously achieving a high spectral resolution. Such a device is directly suitable for airborne/satellite and man-portable sensing instrumentation.