<p> Long-period fiber grating (LPG) sensors have been widely used as refractive index sensors due to their high sensitivity to the ambient refractive index change surrounding the fiber cladding of the LPG. Application of the LPG refractive index sensor has been found in chemical sensing and biochemical sensing, however for application of label-free dip and measure biosensors based on receptor immobilized LPG bio-sensor, the conventional fiber optic refractive index sensors are limited in the refractive index sensitivity, resolution, and operational range owing to the low sensitivity of the cladding mode effective index dependence on the ambient refractive index and the broad-spectrum feature of the LPG transmission spectrum. Low-cost, disposable fiber optic biochemical sensors with improved sensitivity, stability and resolution are needed to provide a high-sensitivity platform for immunology and DNA/aptamer biosensor. </p> <p> In this work, a novel fiber optic biosensing platform based on the LPG and the LPG in-fiber Michelson interferometer is designed and fabricated. The sensitivity and operation range enhancement is optimized by modifying the fiber cladding structure through reducing the cladding layer radius and applying a high-refractive index overlay with appropriate refractive index and thickness. The resolution of the refractive index sensor is improved by adopting the LPG in-fiber Michelson interferometer which turns the wide-spectrum feature of the LPG transmission spectrum into a narrow spectrum feature on the reflection spectrum of the interferometer. The reflection spectrum nature of the LPG in-fiber Michelson interferometer turns the sensor head into a single-end optotrode. The optotrode coated with bio-recognition film thus physically constitutes a short piece of fiber with one section of cladding reduced fiber. With single strand DNA (ssDNA) immobilized on the surface of the fiber cladding through biotin-avidin bridge, detection of the antisense DNA for the immobilized ssDNA is demonstrated. Immunoassay based on capture of target antigen by covalently immobilized antibody shows that reduction of the fiber cladding not only improve the sensitivity of the long period grating in-fiber Michelson interferometric biosensor but also improves the assay time. </p> / Thesis / Doctor of Philosophy (PhD)

No description available.

abstract: Biological membranes are critical to cell sustainability by selectively permeating polar molecules into the intracellular space and providing protection to the interior organelles. Biomimetic membranes (model cell membranes) are often used to fundamentally study the lipid bilayer backbone structure of the biological membrane. Lipid bilayer membranes are often supported using inorganic materials in an effort to improve membrane stability and for application to novel biosensing platforms. Published literature has shown that a variety of dense inorganic materials with various surface properties have been investigated for the study of biomimetic membranes. However, literature does not adequately address the effect of porous materials or supports with varying macroscopic geometries on lipid bilayer membrane behavior. The objective of this dissertation is to present a fundamental study on the synthesis of lipid bilayer membranes supported by novel inorganic supports in an effort to expand the number of available supports for biosensing technology. There are two fundamental areas covered including: (1) synthesis of lipid bilayer membranes on porous inorganic materials and (2) synthesis and characterization of cylindrically supported lipid bilayer membranes. The lipid bilayer membrane formation behavior on various porous supports was studied via direct mass adsorption using a quartz crystal microbalance. Experimental results demonstrate significantly different membrane formation behaviors on the porous inorganic supports. A lipid bilayer membrane structure was formed only on SiO2 based surfaces (dense SiO2 and silicalite, basic conditions) and gamma-alumina (acidic conditions). Vesicle monolayer adsorption was observed on gamma-alumina (basic conditions), and yttria stabilized zirconia (YSZ) of varying roughness. Parameters such as buffer pH, surface chemistry and surface roughness were found to have a significant impact on the vesicle adsorption kinetics. Experimental and modeling work was conducted to study formation and characterization of cylindrically supported lipid bilayer membranes. A novel sensing technique (long-period fiber grating refractometry) was utilized to measure the formation mechanism of lipid bilayer membranes on an optical fiber. It was found that the membrane formation kinetics on the fiber was similar to its planar SiO2 counterpart. Fluorescence measurements verified membrane transport behavior and found that characterization artifacts affected the measured transport behavior. / Dissertation/Thesis / Ph.D. Chemical Engineering 2011

Biosensors have a multitude of important applications in basic research, environmental monitoring, biodefense, and medicine. This research aims to show that Ionic Self-Assembled Multilayers (ISAMs) adsorbed on Long Period Gratings (LPGs) can serve as a highly sensitive, robust, inexpensive optical-based biosensor platform. The ISAM technique is a layer-by-layer deposition method that builds nanometer-thick films based on the principle of Coulomb attraction between oppositely charged polyelectrolyte solutions while LPGs cause strong attenuation bands that enable an optical fiber to be extremely sensitive to changes in the surrounding environment. LPGs have been shown to be highly sensitive to the adsorption of nanoscale self-assembled films on the optical fiber cladding surface. In this work, we utilize Turnaround Point (TAP) LPGs, which possess even greater sensitivity than standard LPGs. This thesis focuses on evaluation of approaches to increasing the sensitivity of the sensor platfom, implementation of a biosensor for detection of several biomolecules, and preliminary evaluation of the potential for pH sensing. For a thin-film coated TAP LPG, we have demonstrated that shifts in the transmitted light intensity at the resonant wavelength of the LPG can result from the variation in film thickness and/or refractive index. We have observed decreases in intensity as large a 7 dB for one bilayer of ISAM film (~1 nm), which corresponds to an 80% decrease in the transmitted light intensity at the resonant wavelength. We have also shown that the sensitivity of the TAP LPG sensor can be increased by implementing nm-thick ISAM films that have a refractive index greater than silica. Furthermore, it is shown that incorporation of silica nanoparticles into the ISAM films significantly increases sensitivity through increased surface area and thickness. The biotin-streptavidin system was used as a model for implementaion and optimization of the ISAM-coated TAP LPG biosensor platform. Through evaluation of various biotin derivatives to maximize the amount functionalized onto the ISAM film, optimization of the ISAM film properties, and use of LPGs designed for higher sensitivity, the minimum detectable concentration of streptavidin was decreased from 0.0125 mg/ml to 12.0 ng/ml. The biosensor platform was then tested on prostate specific antigen (PSA), which is used as a clinical marker for early diagnosis of potential prostate cancer. Using a direct crosslinking approach of the monoclonal antibody to PSA into the ISAM film, a sensitivity level of 11.64 ng/ml PSA was obtained through combined optimization of the ISAM film and antibody surface coverage. Finally, the potential of ISAM TAP LPGs as pH sensors was examined based on the pH dependent swelling of ISAM films. / Ph. D.

Biosensors have widespread applications in many areas. Currently the Surface Plasmon Resonance (SPR) biosensor is one of the most prevalent types of biosensor. However, it has several disadvantages such as being delicate, expensive, and non-portable. Ionic Self-Assembled Multilayers (ISAMs) adsorbed on Long Period Fiber Gratings (LPGs) provides an attractive platform for building optical sensors, which could potentially overcome the disadvantages of SPR biosensors. The ISAM technique is a type of layer-by-layer deposition technique for building nanoscale thin films. An LPG is a type of fiber device that is sensitive to physical property changes of the ambient environment. LPGs have been extensively investigated for use as optical sensors. We have carried out a study on combining these two techniques to build efficient biosensors. In this thesis, we demonstrate ultra-sensitive LPGs whose attenuation can be changed by 25 dB (~99.7%) over a 48-nm spectral band, with ambient-index changes of only 2.7E-4. The device schematic allows arbitrarily high index sensitivities to be achieved, which makes it an attractive platform for realizing sensors and modulators that respond to small index changes. For a thin-film coated LPG, we find theoretically that the resonant wavelength shift of the LPG can result from either the variation of the thickness of the film and/or the variation of its refractive index. Furthermore, results illustrate that the sensitivity of the sensor could be enhanced using a nm-thick thin-film (e.g. ISAM films) whose refractive index is greater than silica. Experimentally, we demonstrate the fabrication of nm-thick ISAM films deposited on LPGs, which induces dramatic shifts in the resonant wavelength. The refractive index and the thickness of the ISAM film was precisely controlled by altering the relative fraction of the anionic and cationic materials combined with layer-by-layer deposition. Finally, we demonstrate that ISAM-coated LPGs can function effectively as biosensors by using the biotin-streptavidin system. These demonstrations confirm that the ISAM-LPG scheme provides a thermally-stable, reusable, and robust platform for building efficient optical sensors. / Ph. D.

In der medizinischen Diagnostik, Bioverfahrenstechnik und Umwelttechnik besteht ein steigender Bedarf an kompakten Analysegeräten für die schnelle Vor-Ort-Detektion spezifischer biochemischer Substanzen. Im Rahmen der Arbeit wurde daher ein neuartiger faseroptischer Sensor entwickelt, der in der Lage ist kleinste Brechzahländerungen, z.B. durch molekulare Bindungsprozesse, zu detektieren. Die hohe Empfindlichkeit an der vergoldeten Spitze der Sensorfaser beruht auf der Oberflächenplasmonenresonanz (SPR) einer einzelnen Mantelmode, die durch ein langperiodisches Fasergitter (LPG) ermöglicht wird. Die Übertragungsfunktion des Sensors wurde unter Verwendung eines Schichtwellenleitermodells schnell und präzise modelliert. Es konnte gezeigt werden, dass in einem wässrigen Umgebungsmedium die höchste Empfindlichkeit im Spektralbereich um 660 nm unter Annahme einer rund 35~nm dicken und 2~mm langen Goldbeschichtung erreicht wird. Weiterhin wurde nachgewiesen, dass mit einer intermediale Schicht aus Cadmiumsulfid die SPR der Mantelmode in einen höheren Spektralbereich verschoben und damit die Empfindlichkeit deutlich verbessert werden kann. Um eine geringe Polarisationsabhängigkeit des Sensors sicherzustellen, wurde ein nasschemisches Abscheidungsverfahren für die allseitige Goldbeschichtung der Sensorfaser entwickelt. Die spezifischen optischen Eigenschaften dieser Abscheidungen wurden mit Hilfe von LPGs untersucht, die durch eine spezielle UV-Belichtung hergestellt wurden. Die Experimente ergaben, dass die komplexe Permittivität nasschemischer Abscheidungen mit Schichtdicken oberhalb von 50~nm mit aufgedampften Goldschichten vergleichbar ist. Die Verluste der adressierten Mantelmoden wurden mit einer äquivalenten Sensoranordnung aus zwei identischen LPG untersucht. Dabei konnte ein Skalierfaktor abgeleitet werden, der die effiziente Berechnung der Mantelmodendämpfung erlaubt. Es wurde nachgewiesen, dass die Brechzahlauflösung etablierter volumenoptischer SPR-Sensoren mit einer einfachen Transmissionsmessung an einer geeigneten Wellenlänge erreicht werden kann. Die äußerst kompakte Sensorfläche des faseroptischen Sensors ermöglicht darüber hinaus die Untersuchung deutlich kleinerer Probenvolumina ohne ein zusätzliches mikrofluidisches System zu benötigen. Es wurde gezeigt, dass sekundäre Brechzahländerungen aufgrund von Temperaturschwankungen oder unspezifische Ablagerungen durch eine differentielle Auswertung zweier identischer Sensoren kompensiert werden können. Die verbleibende Querempfindlichkeit wird durch die Polarisationsabhängigkeit der Sensoren bestimmt. Die geringste Querempfindlichkeit konnte daher mit einer homogenen nasschemischen abgeschiedenen Sensorfläche nachgewiesen werden. / Compact analysis devices which facilitate the rapid detection of specific biochemical substances are in increasing demand in the fields of point-of-care medical diagnostics, bioprocess engineering and environmental engineering. The aim of this work was therefore to design a novel fiber-optic sensor able to detect small refractive index changes such as those caused by molecular binding processes. The high level of sensitivity at the gold-plated tip of the sensor fiber stems from the surface plasmon resonance (SPR) of a single cladding mode, which is the result of a long-period fiber grating (LPG). The transfer function of the sensor was calculated quickly and accurately using a slab waveguide model. It was observed that the highest level of sensitivity in an aqueous ambient medium is achieved at a wavelength of 660 nm assuming a gold coating of 35 nm in thickness and 2 mm in length. Furthermore, it was demonstrated that an intermedial cadmium sulfide layer shifts the SPR of the cladding mode towards higher wavelengths, thus leading to significantly enhanced sensitivity. An electroless plating process for the omnidirectional deposition of gold on the sensor fiber was developed in order to minimize the sensor\'s dependency on polarization. The specific optical properties of the gold layer deposited were investigated with the aid of LPGs fabricated using a special UV exposure method. The experiments showed the complex permittivity of electroless platings with a thickness of over 50 nm to be comparable with that of evaporated gold layers. The losses of the addressed cladding modes were investigated using an equivalent sensor setup consisting of two identical LPGs. This facilitated the determination of a scaling factor enabling the effcient calculation of cladding mode attenuation. It was demonstrated that it is possible to obtain the refractive index resolution of established volume optical SPR sensors with the aid of simple transmission measurements at a specific wavelength. Moreover, the extremely compact sensing area of the fiber-optic sensor enables the investigation of smaller sample volumes without the need for an additional microfluidic system. Secondary refractive index changes caused by temperature fluctuations or unspecific binding events can be compensated for by means of the differential interrogation of two identical fiber-optic sensors. The residual cross sensitivity is determined by the polarisation dependency of the sensor. The lowest cross sensitivity was therefore demonstrated in combination with a homogeneous electroless plated sensor surface.

In der medizinischen Diagnostik, Bioverfahrenstechnik und Umwelttechnik besteht ein steigender Bedarf an kompakten Analysegeräten für die schnelle Vor-Ort-Detektion spezifischer biochemischer Substanzen. Im Rahmen der Arbeit wurde daher ein neuartiger faseroptischer Sensor entwickelt, der in der Lage ist kleinste Brechzahländerungen, z.B. durch molekulare Bindungsprozesse, zu detektieren. Die hohe Empfindlichkeit an der vergoldeten Spitze der Sensorfaser beruht auf der Oberflächenplasmonenresonanz (SPR) einer einzelnen Mantelmode, die durch ein langperiodisches Fasergitter (LPG) ermöglicht wird. Die Übertragungsfunktion des Sensors wurde unter Verwendung eines Schichtwellenleitermodells schnell und präzise modelliert. Es konnte gezeigt werden, dass in einem wässrigen Umgebungsmedium die höchste Empfindlichkeit im Spektralbereich um 660 nm unter Annahme einer rund 35~nm dicken und 2~mm langen Goldbeschichtung erreicht wird. Weiterhin wurde nachgewiesen, dass mit einer intermediale Schicht aus Cadmiumsulfid die SPR der Mantelmode in einen höheren Spektralbereich verschoben und damit die Empfindlichkeit deutlich verbessert werden kann. Um eine geringe Polarisationsabhängigkeit des Sensors sicherzustellen, wurde ein nasschemisches Abscheidungsverfahren für die allseitige Goldbeschichtung der Sensorfaser entwickelt. Die spezifischen optischen Eigenschaften dieser Abscheidungen wurden mit Hilfe von LPGs untersucht, die durch eine spezielle UV-Belichtung hergestellt wurden. Die Experimente ergaben, dass die komplexe Permittivität nasschemischer Abscheidungen mit Schichtdicken oberhalb von 50~nm mit aufgedampften Goldschichten vergleichbar ist. Die Verluste der adressierten Mantelmoden wurden mit einer äquivalenten Sensoranordnung aus zwei identischen LPG untersucht. Dabei konnte ein Skalierfaktor abgeleitet werden, der die effiziente Berechnung der Mantelmodendämpfung erlaubt. Es wurde nachgewiesen, dass die Brechzahlauflösung etablierter volumenoptischer SPR-Sensoren mit einer einfachen Transmissionsmessung an einer geeigneten Wellenlänge erreicht werden kann. Die äußerst kompakte Sensorfläche des faseroptischen Sensors ermöglicht darüber hinaus die Untersuchung deutlich kleinerer Probenvolumina ohne ein zusätzliches mikrofluidisches System zu benötigen. Es wurde gezeigt, dass sekundäre Brechzahländerungen aufgrund von Temperaturschwankungen oder unspezifische Ablagerungen durch eine differentielle Auswertung zweier identischer Sensoren kompensiert werden können. Die verbleibende Querempfindlichkeit wird durch die Polarisationsabhängigkeit der Sensoren bestimmt. Die geringste Querempfindlichkeit konnte daher mit einer homogenen nasschemischen abgeschiedenen Sensorfläche nachgewiesen werden. / Compact analysis devices which facilitate the rapid detection of specific biochemical substances are in increasing demand in the fields of point-of-care medical diagnostics, bioprocess engineering and environmental engineering. The aim of this work was therefore to design a novel fiber-optic sensor able to detect small refractive index changes such as those caused by molecular binding processes. The high level of sensitivity at the gold-plated tip of the sensor fiber stems from the surface plasmon resonance (SPR) of a single cladding mode, which is the result of a long-period fiber grating (LPG). The transfer function of the sensor was calculated quickly and accurately using a slab waveguide model. It was observed that the highest level of sensitivity in an aqueous ambient medium is achieved at a wavelength of 660 nm assuming a gold coating of 35 nm in thickness and 2 mm in length. Furthermore, it was demonstrated that an intermedial cadmium sulfide layer shifts the SPR of the cladding mode towards higher wavelengths, thus leading to significantly enhanced sensitivity. An electroless plating process for the omnidirectional deposition of gold on the sensor fiber was developed in order to minimize the sensor\'s dependency on polarization. The specific optical properties of the gold layer deposited were investigated with the aid of LPGs fabricated using a special UV exposure method. The experiments showed the complex permittivity of electroless platings with a thickness of over 50 nm to be comparable with that of evaporated gold layers. The losses of the addressed cladding modes were investigated using an equivalent sensor setup consisting of two identical LPGs. This facilitated the determination of a scaling factor enabling the effcient calculation of cladding mode attenuation. It was demonstrated that it is possible to obtain the refractive index resolution of established volume optical SPR sensors with the aid of simple transmission measurements at a specific wavelength. Moreover, the extremely compact sensing area of the fiber-optic sensor enables the investigation of smaller sample volumes without the need for an additional microfluidic system. Secondary refractive index changes caused by temperature fluctuations or unspecific binding events can be compensated for by means of the differential interrogation of two identical fiber-optic sensors. The residual cross sensitivity is determined by the polarisation dependency of the sensor. The lowest cross sensitivity was therefore demonstrated in combination with a homogeneous electroless plated sensor surface.

Searching with the key word “measuring instrument of traditional Chinese medical massage” in CNK, 62 academic literature papers can be found. According to statistics, research of “measuring instrument of traditional Chinese medical massage” are carried out in 5 directions, including normalized operation, high-tech based teaching and training, perception analysis of massage manipulation force, the structural design of robot, and the design of measuring instrument. As the manipulation of traditional Chinese medical massage is a multi-field medical effect, without the supporting of measurement of high-tech based multi-field sensor of massage actions, the quantification, normalized and standardized operation, scientific and modern teaching, microcosmic, precise and quantified perception, robotized and intellectualized actuation implementation, and design of measuring instrument are hard to realize. Meanwhile, the online diagnosis and treatment service model of traditional Chinese medical massage based on “internet plus” depends on the establishment of digital database of massage manipulation, which is based on the creation of high-tech sensor system of traditional Chinese medical massage measurement. Thus, the measuring sensor of the traditional Chinese medical massage manipulation is an unavoidable key scientific problem for scientific, normalized, and internet-enabled traditional Chinese medical massage. Flexible fiber grating sensor array will be a research direction for implementing multi-field measurement of traditional Chinese medical massage manipulation.

Carbon dioxide sequestration is one of many mitigation tools available to help reduce carbon dioxide emissions while other disposal/repurposing methods are being investigated. Geologic sequestration is the most stable option for long-term storage of carbon dioxide (CO2), with significant CO2 trapping occurring through mineralization within the first 20-50 years. A fiber optic based monitoring system has been proposed to provide real time concentrations of CO2 at various points throughout the geologic formation. The proposed sensor is sensitive to the refractive index (RI) of substances in direct contact with the sensing component. As RI is a measurement of light propagating through a bulk medium relative to light propagating through a vacuum, the extraction of the effects of any specific component of that medium to the RI remains very difficult. Therefore, a requirement for a selective barrier to be able to prevent confounding substances from being in contact with the sensor and specifically isolate CO2 is necessary. As such a method to evaluate the performance of the selective element of the sensor was investigated. Polybenzimidazole (PBI) and VTEC polyimide (PI) 1388 are high performance polymers with good selectivity for CO2 used in high temperature gas separations. These polymers were spin coated onto a glass substrate and cured to form ultra-thin (>10 μm) membranes for gas separation. At a range of pressures (0.14 –0.41 MPa) and a set temperature of 24.2±0.8 °C, intrinsic permeabilities to CO2 and nitrogen (N2) were investigated as they are the gases of highest prevalence in underground aquifers. Preliminary RI testing for proof of concept has yielded promising results when the sensor is exposed exclusively to CO2 or N2. However, the use of both PBI and VTEC PI in these trials resulted in CO2 selectivities of 0.72 to 0.87 and 0.33 to 0.63 respectively, for corresponding feed pressures of 0.14 to 0.41 MPa. This indicates that both of the polymers are more selective for N2 and should not be used in CO2 sensing applications as confounding gas permeants, specifically N2, will interfere with the sensing element. / Graduate / 0428 / 0495 / 0542 / ben.t.davies@gmail.com

The present work deals with the development and application of an acoustic long-period fiber grating (LPG) in conjunction with a special optical fiber (SF). The acoustic LPG converts selected optical modes of the SF. Some of these modes are characterized by complex, yet cylindrically symmetric polarization and intensity patterns. Therefore, they are the guided variant of so called cylindrical vector beams (CVBs). CVBs find applications in numerous fields of fundamental and applied optics. Here, an application to high-resolution light microscopy is demonstrated. The field distribution in the tight microscope focus is controlled by the LPG, which in turn creates the necessary polarization and intensity distribution for the microscope illumination. A gold nanoparticle of 30 nm diameter is used to probe the focal field with sub-wavelength resolution. The construction and test of the acoustic LPG are discussed in detail. A key component is the piezoelectric transducer that excites flexural acoustic waves in the SF, which are the origin of an optical mode conversion. A mode conversion efficiency of 85% was realized at 785 nm optical wavelength. The efficiency is, at present, mainly limited by the spectral positions and widths of the transducer’s acoustic resonances. The SF used with the LPG separates the propagation constants of the second-order polarization modes, so they can be individually excited and are less sensitive to distortions than in standard weakly-guiding fibers. The influence of geometrical parameters of the fiber core on the propagation constant separation and on the mode fields is studied numerically using the multiple multipole method. From the simulations, a simple mode coupling scheme is developed that provides a qualitative understanding of the experimental results achieved with the LPG. The refractive index profile of the fiber core was originally developed by Ramachandran et al. However, an important step of the present work is to reduce the SF’s core size to counteract the the appearance of higher-order modes at shorter wavelengths which would otherwise spoil the mode purity. Using the acoustic LPG in combination with the SF produces a versatile device to generate CVBs and other phase structures beams. This fiber-optical method offers beam profiles of high quality and achieves good directional stability of the emitted beam. Moreover, the device design is simple and can be realized at low cost. Future developments of the acoustic LPG will aim at applications to fiber-optical sensors and optical near-field microscopy. / Diese Arbeit behandelt die Entwicklung und Anwendung eines akustischen langperiodischen Fasergitters (LPG) in Verbindung mit einer optischen Spezialfaser (SF). Das akustische LPG wandelt ausgewählte optische Modi der SF um. Einige dieser Modi weisen eine komplexe, zylindersymmetrische Polarisations- und Intensitätsverteilung auf. Diese sind eine Form der so genannten zylindrischen Vektor-Strahlen (CVBs), welche in zahlreichen Gebieten der wissenschaftlichen und angewandten Optik zum Einsatz kommen. In dieser Arbeit wird eine Anwendung auf die hochauflösende Lichtmikroskopie demonstriert. Die fokale Feldverteilung wird dabei durch die Auswahl der vom LPG erzeugten Modi, welche zur Beleuchtung genutzt werden, eingestellt. Als Nachweis wird die entstehende laterale Feldverteilung mithilfe eines Goldpartikels (Durchmesser 30 Nanometer) vermessen. Aufbau und Test des akustischen LPGs werden im Detail besprochen. Eine wichtige Komponente ist ein piezoelektrischer Wandler, der akustische Biegewellen in der SF anregt. Diese sind die Ursache der Umwandlung optischer Modi. Die maximale Konversionseffizienz betrug 85% bei 785 nm (optischer) Wellenlänge. Die Effizienz ist derzeit hauptsächlich durch die Lage der akustischen Resonanzfrequenzen des Wandlers und deren Bandbreite begrenzt. Die benutzte SF spaltet die Ausbreitungskonstanten von Polarisationsmodi zweiter Ordnung auf, sodass diese individuell angeregt werden können und weniger anfällig gegen über Störungen der Faser sind, als das bei gewöhnlichen, schwach führenden Glasfasern der Fall ist. Das zu Grunde liegende Brechzahlprofil des Faserkerns wurde von Ramachandran et al. entwickelt. Für diese Arbeit wurde jedoch die Ausdehnung des Profils verkleinert – ein erster Schritt um Anwendungen bei kürzeren optischen Wellenlängen zu ermöglichen. Es werden numerische Simulationen mit der Methode der multiplen Multipole zur Berechnung der Modenfelder und den zugehörigen Propagationskonstanten vorgestellt. Diese zeigen u. a. den starken Einfluss von geometrischen Veränderungen des Faserkerns. Basierend auf den Simulationsergebnissen wird ein einfaches Kopplungsschema für die Modi entwickelt, welches ein qualitatives Verständnis der experimentellen Ergebnisse ermöglicht. In Kombination bilden die SF und das LPG ein vielseitiges Gerät zur Erzeugung von CVBs und anderen Strahlen mit komplexer Phasenstruktur. Die Methode besticht durch hohe Qualität des Strahlprofils, stabile Abstrahlrichtung, einfachen Aufbau, elektronische Steuerbarkeit und geringe Materialkosten. Zukünftige Weiterentwicklungen des akustischen LPGs zielen auf die Anwendung in faseroptischen Sensoren und in der optischen Nahfeldmikroskopie ab.