Spelling suggestions: "subject:"bainite Element amodelling"" "subject:"bainite Element bmodelling""
31 |
Hot tearing and constitutive behaviour of semi-solid aluminum alloysPhillion, Andre 05 1900 (has links)
The occurrence of hot tearing during solidification is one of the major factors influencing both the quality and productivity of aluminum castings. In order to reduce the formation of hot tears, quantitative information regarding both hot tearing formation and semi-solid deformation is essential.
In this study, the mechanisms of hot tearing and semi-solid deformation have been investigated via two novel techniques: x-ray micro-tomography on material deformed in the semi-solid region, and development of a three phase microstructural model based on a geometry derived from a Voronoi diagram with rounded corners and porosity. Numerical techniques were utilized to quantify both the size evolution and orientation of internal damage relative to void growth. In order to conduct the above research, a new semi-solid tensile deformation methodology was devised which uses a two thermocouple control technique to enable accurate measurement of semi-solid tensile strength and ductility. The experimental work was conducted on the aluminum – magnesium alloy AA5182 in the as-cast and hot isostatic pressing (HIP) states.
The x-ray micro-tomography technique was used to observe that semi-solid deformation is accommodated by internal damage via growth of as-cast porosity and the nucleation of new damage-based voids. As the volume fraction of damage increases, the growth of voids occurs in an orientation perpendicular to the loading direction, both through expansion within the grain boundary liquid and via coalescence between voids. The damage then localizes, causing failure.
The finite element semi-solid microstructural model was used to explore the effects of fraction solid, fraction porosity, and grain size on semi-solid constitutive behaviour. The simulations revealed that increased grain size and fraction porosity lead to a reduction in flow stress for a given fraction solid. Furthermore, local strain accumulation was linked to hot tearing, since strain localizes in the liquid very early in the deformation process. Based on the model predictions, a new constitutive relationship was developed over the range 0.75 < fs < 0.95.
Together, these two techniques have provided powerful new insight, such as the critical role played by as-cast porosity, on the phenomena of hot tearing and semi-solid deformation in aluminum alloys.
|
32 |
Train-induced dynamic response of railway track and embankments on soft peaty foundationsHendry, Michael Thomson 15 August 2007
The mainline railway track between Dublin and Belfast in Northern Ireland was constructed during the 1850's. Substantial lengths of railway embankment were constructed over poor-quality peaty soils. This was accomplished using tree trunk fascines placed directly on the natural ground surface; with poor-quality local peaty soils used as light weight fill.<p>In recent years, Northern Ireland Railways have noticed that these sections of railway track have been deteriorating more rapidly than sections of the track where the foundations are more competent. The magnitudes of displacement of the track under train loading appear to be increasing gradually over time and train speeds have had to be reduced.<p>This thesis is based on the research done to monitor the response of these railway track and embankment structures to dynamic train loading. The displacements were monitored for two different embankments under a variety of loading conditions and for various seasonal conditions. These displacements were recorded using a sensor created for this task. The sensor consisted of a photo-sensitive array mounted on the sleepers and a laser, which was placed outside the area of influence of train loading, and shone on the photo-sensitive array. <p>Analytical (Winkler) modelling was conducted to determine the effects of train speed and the cause of the large train-induced displacements. Analytical and finite element modelling were used to determine the effectiveness of alternative methods of embankment stabilization.<p>The results from the analytical modelling suggest that the deformation of the embankment under train loading was not due to dynamic excitation, but static deformation of the poor-quality fill and soft foundation materials. From both the analytical and finite element modelling of possible remediation techniques, methods that stiffen the embankment and foundation material are shown to be the most effective at reducing the train induced deflection of the embankment.
|
33 |
Modelling of headed stud in steel ¿ precast composite beams.El-Lobody, E., Lam, Dennis January 2002 (has links)
Use of composite steel construction with precast hollow core slabs is now popular in the UK,but the present knowledge in shear capacity of the headed shear studs for this type of composite construction is very limited. Currently, all the information is based on the results obtained from experimental push-off tests. A finite element model to simulate the behaviour of headed stud shear connection in composite beam with precast hollow core slabs is described. The model is based on finite element method and takes into account the linear and non-linear behaviour of all the materials. The model has been validated against the test results, for which the accuracy of the model used is demonstrated. Parametric studies showing the effect of the change in transverse gap size, transverse reinforcement diameter and in-situ concrete strength on the shear connection capacity are presented.
|
34 |
Detection of defects in timber using dynamic excitation and vibration analysisMoshiri, Farzad, Mobasher, Bahareh, Talib Issa, Osama January 2009 (has links)
This thesis evaluates the possibility to detect natural defects, such as knots, in timber boards using dynamic excitation test and ABAQUS software. In the study the edgewise bending direction were compared with axial direction. Dynamic excitation and modal analysis were used to extract the natural frequencies of several sound and artificially defected boards with the help of Signalcalc. Mobylizer software. By using the first edgewise natural frequency, modulus of elasticity (MOE) was calculated. An ABAQUS 2D Finite Element model was utilized to model the board and to extract the frequencies for the six first mode shapes in both axial and edgewise directions. The extracted frequencies from the model were compared with the frequencies from the tests. The analytical and experimental results, from the homogeneous boards, in edgewise direction has similar frequency variations. The defects in the timber boards decreased the natural frequencies. The bending modes with more curvature at the location of the artificial defect displayed more frequency deviation in that mode. The variation in response frequencies for uniform and defected boards was more noticeable in edgewise bending modes than in longitudinal modes.
|
35 |
Train-induced dynamic response of railway track and embankments on soft peaty foundationsHendry, Michael Thomson 15 August 2007 (has links)
The mainline railway track between Dublin and Belfast in Northern Ireland was constructed during the 1850's. Substantial lengths of railway embankment were constructed over poor-quality peaty soils. This was accomplished using tree trunk fascines placed directly on the natural ground surface; with poor-quality local peaty soils used as light weight fill.<p>In recent years, Northern Ireland Railways have noticed that these sections of railway track have been deteriorating more rapidly than sections of the track where the foundations are more competent. The magnitudes of displacement of the track under train loading appear to be increasing gradually over time and train speeds have had to be reduced.<p>This thesis is based on the research done to monitor the response of these railway track and embankment structures to dynamic train loading. The displacements were monitored for two different embankments under a variety of loading conditions and for various seasonal conditions. These displacements were recorded using a sensor created for this task. The sensor consisted of a photo-sensitive array mounted on the sleepers and a laser, which was placed outside the area of influence of train loading, and shone on the photo-sensitive array. <p>Analytical (Winkler) modelling was conducted to determine the effects of train speed and the cause of the large train-induced displacements. Analytical and finite element modelling were used to determine the effectiveness of alternative methods of embankment stabilization.<p>The results from the analytical modelling suggest that the deformation of the embankment under train loading was not due to dynamic excitation, but static deformation of the poor-quality fill and soft foundation materials. From both the analytical and finite element modelling of possible remediation techniques, methods that stiffen the embankment and foundation material are shown to be the most effective at reducing the train induced deflection of the embankment.
|
36 |
Detection of defects in timber using dynamic excitation and vibration analysisMoshiri, Farzad, Mobasher, Bahareh, Talib Issa, Osama January 2009 (has links)
<p>This thesis evaluates the possibility to detect natural defects, such as knots, in timber boards using dynamic excitation test and ABAQUS software. In the study the edgewise bending direction were compared with axial direction. Dynamic excitation and modal analysis were used to extract the natural frequencies of several sound and artificially defected boards with the help of Signalcalc. Mobylizer software. By using the first edgewise natural frequency, modulus of elasticity (MOE) was calculated. An ABAQUS 2D Finite Element model was utilized to model the board and to extract the frequencies for the six first mode shapes in both axial and edgewise directions. The extracted frequencies from the model were compared with the frequencies from the tests. The analytical and experimental results, from the homogeneous boards, in edgewise direction has similar frequency variations. The defects in the timber boards decreased the natural frequencies. The bending modes with more curvature at the location of the artificial defect displayed more frequency deviation in that mode. The variation in response frequencies for uniform and defected boards was more noticeable in edgewise bending modes than in longitudinal modes.</p>
|
37 |
Hot tearing and constitutive behaviour of semi-solid aluminum alloysPhillion, Andre 05 1900 (has links)
The occurrence of hot tearing during solidification is one of the major factors influencing both the quality and productivity of aluminum castings. In order to reduce the formation of hot tears, quantitative information regarding both hot tearing formation and semi-solid deformation is essential.
In this study, the mechanisms of hot tearing and semi-solid deformation have been investigated via two novel techniques: x-ray micro-tomography on material deformed in the semi-solid region, and development of a three phase microstructural model based on a geometry derived from a Voronoi diagram with rounded corners and porosity. Numerical techniques were utilized to quantify both the size evolution and orientation of internal damage relative to void growth. In order to conduct the above research, a new semi-solid tensile deformation methodology was devised which uses a two thermocouple control technique to enable accurate measurement of semi-solid tensile strength and ductility. The experimental work was conducted on the aluminum – magnesium alloy AA5182 in the as-cast and hot isostatic pressing (HIP) states.
The x-ray micro-tomography technique was used to observe that semi-solid deformation is accommodated by internal damage via growth of as-cast porosity and the nucleation of new damage-based voids. As the volume fraction of damage increases, the growth of voids occurs in an orientation perpendicular to the loading direction, both through expansion within the grain boundary liquid and via coalescence between voids. The damage then localizes, causing failure.
The finite element semi-solid microstructural model was used to explore the effects of fraction solid, fraction porosity, and grain size on semi-solid constitutive behaviour. The simulations revealed that increased grain size and fraction porosity lead to a reduction in flow stress for a given fraction solid. Furthermore, local strain accumulation was linked to hot tearing, since strain localizes in the liquid very early in the deformation process. Based on the model predictions, a new constitutive relationship was developed over the range 0.75 < fs < 0.95.
Together, these two techniques have provided powerful new insight, such as the critical role played by as-cast porosity, on the phenomena of hot tearing and semi-solid deformation in aluminum alloys.
|
38 |
Ice dynamics and mass balance in the grounding zone of outlet glaciers in the Transantarctic MountainsMarsh, Oliver John January 2013 (has links)
The Antarctic grounding zone has a disproportionately large effect on glacier dynamics and ice sheet stability relative to its size but remains poorly characterised across much of the continent. Accurate ice velocity and thickness information is needed in the grounding zone to determine glacier outflow and establish to what extent changing ocean and atmospheric conditions are affecting the mass balance of individual glacier catchments.
This thesis describes new satellite remote sensing techniques for measuring ice velocity and ice thickness, validated using ground measurements collected on the Beardmore, Skelton and Darwin Glaciers and applied to other Transantarctic Mountain
outlet glaciers to determine ice discharge. Outlet glaciers in the Transantarctic Mountains provide an important link between the East and West Antarctic Ice Sheets but remain inadequately studied. While long-term velocities in this region
are shown here to be stable, instantaneous velocities are sensitive to stresses induced by ocean tides, with fluctuations of up to 50% of the mean observed in GPS measurements. The potential error induced in averaged satellite velocity measurements due to these effects is shown to be resolvable above background noise in the grounding zone but to decrease rapidly upstream. Using a new inverse finite-element modelling
approach based on regularization of the elastic-plate bending equations, tidal flexure information from differential InSAR is used to calculate ice stiffness and infer thickness in the grounding zone. This technique is shown to be successful at reproducing the thickness distribution for the Beardmore Glacier, eliminating current issues in the calculation of thickness from freeboard close to the grounding line where ice is not in hydrostatic equilibrium. Modelled thickness agrees to within 10% of ground penetrating radar measurements. Calibrated freeboard measurements and tide-free velocities in the grounding zones of glaciers in the western Ross Sea are used to calculate grounding zone basal melt rates, with values between 1.4 and 11.8 m/a⁻¹ in this region. While strongly dependent on grounding line ice thickness and velocity, melt rates show no latitudinal trend between glaciers, although detailed error analysis highlights the need for much improved estimates of firn density distribution in regions of variable accumulation such as the Transantarctic Mountains.
|
39 |
The Influence of Dynamic Response Characteristics on Traumatic Brain InjuryPost, Andrew 22 July 2013 (has links)
Research into traumatic brain injury (TBI) mechanisms is essential for the development of methods to prevent its occurrence. One of the most common ways to incur a TBI is from falls, especially for the young and very old. The purpose of this thesis was to investigate how the acceleration loading curves influenced the occurrence of different types of TBI, namely: epidural hematoma, subdural hematoma, subarachnoid hemorrhage, and contusion. This investigation was conducted in three parts. The first study conducted reconstructions of 20 TBI cases with varying outcomes using MADYMO, Hybrid III, and finite element methodologies. This study provided a dataset of threshold values for each of the TBI injuries measured in parameters of strain and stress. The results of this study indicated that using a combined reconstructive approach produces results which are in keeping with the literature for TBI. The second study examined how the characteristics of the loading curves which were produced from each reconstruction influenced the outcome using a principal components analysis. It was found that the duration of the event accounted for much of the variance in the results, followed with the acceleration components. Different curve characteristics also accounted for differing amounts of variance in each of the lesion types. Study 3 examined how the dynamic response of the impact influenced where in the brain a subdural hematoma (SDH) could occur. It was found that the largest magnitudes of acceleration produced SDH in the parietal lobe, and the lowest in the occipital lobe. Overall this thesis examined the mechanism of injury for TBI using a large dataset with methodologies which complement each other’s limitations. As a result in depth information of the nature of TBI was attained and information provided which may be used to improve future protection and standard development.
|
40 |
Biomechanical modelling of the whole human spine for dynamic analysisEsat, Volkan January 2006 (has links)
Developing computational models of the human spine has been a hot topic in biornechanical research for a couple of decades in order to have an understanding of the behaviour of the whole spine and the individual spinal parts under various loading conditions. The objectives of this thesis are to develop a biofidefic multi-body model of the whole human spine especially for dynamic analysis of impact situations, such as frontal impact in a car crash, and to generate finite element (FE) models of the specific spinal parts to investigate causes of injury of the spinal components. As a proposed approach, the predictions of the multi-body model under dynamic impact loading conditions, such as reaction forces at lumbar motion segments, were utilised not only to have a better understanding of the gross kinetics and kinematics of the human spine, but also to constitute the boundary conditions for the finite element models of the selected spinal components. This novel approach provides a versatile, cost effective and powerful tool to analyse the behaviour of the spine under various loading conditions which in turn helps to develop a better understanding of injury mechanisms.
|
Page generated in 0.0801 seconds