90 leaves on CD format, preliminary i-ix pages and numbered pages 1-81. Includes bibliography, list of figures in color to pdf format (OCR). / Thesis (MSc (Chemistry and Polymer Science))--University of Stellenbosch, 2005. / ENGLISH ABSTRACT: The composition of petrochemical products obtained from Fischer Tropsch (FT) technologies is of the highest complexity possible and may contain thousands of components. Chemicals produced from FT feedstocks often contain trace level contaminants that can poison catalysts or that affect product performance in down-line processes. Single dimension GC analysis of these mixtures provides incomplete information because of lack of separation power. This study evaluates the separation power of heart-cut GC-GC, comprehensive GCxGC and sequential GC-GC for three selected challenging petrochemical applications. The fundamental theoretical aspects of the techniques are discussed. Oxygenates are removed as far as possible in C10 – C13 alkylation feedstocks, used in the production of linear alkyl benzenes, because the oxygenates may have deactivating effects on some expensive alkylation catalysts. Residual oxygenates may still be present and can consist of hundreds of components. Detection of individual components at ng/g levels is required. Heart-cut GC-GC is used to illustrate the separation and enrichment power for oxygenates in an alkylation feedstock. The stationary phase in the first dimension column was selected to provide separation of the oxygenates from the hydrocarbons in a relatively narrow window. The oxygenate fraction is then enriched by repeated injections and collection on the cryotrap. After sufficient enrichment, the trap is heated and the oxygenates are analysed on the second dimension column. Comprehensive GCxGC and Sequential GC-GC are compared for the separation and analysis of the oxygenated chemical component classes in the alkylation feedstock, before removal of oxygenates. Cyclic alcohols can occur in detergent alcohols produced from FT feedstocks. These cyclics are regarded as impurities because they affect the physical properties of the detergents. The cyclic and noncyclic alcohols in a narrow C12 – C13 detergent alcohol distillation cut have similar boiling points and polarities, and separation of individual components is thus difficult to achieve. Comprehensive GCxGC and sequential GC-GC are evaluated for the separation of the alcohol component classes. The study shows that both approaches provide component class separation but the high resolving power of the second column and the optimal chromatographic operating conditions of sequential GC-GC provide better separation of the individual components. The study illustrates the immense power of the three multidimensional GC techniques namely heart-cut GC-GC, comprehensive GCxGC and sequential GC-GC. The three multidimensional GC techniques each have their own advantages, disadvantages and unique applications and should be used as complementary rather than as competitive analytical tools. / AFRIKAANSE OPSOMMING: Fischer Tropsch (FT) petrochemiese produkte is van baie hoë kompleksiteit en kan uit duisende komponente bestaan. Chemikalië afkomstig van dié voerstrome bevat soms spoorhoeveelhede onsuiwerhede wat deaktiverend op kataliste kan inwerk of wat die werkverrrigting van finale produkte kan beïnvloed. Enkeldimensie GC analises van die komplekse mengsels is meesal onakkuraat as gevolg van geweldige piekoorvleueling. Die studie evalueer die skeidingsvermoë van drie multidimensionele tegnieke, Heart-cut GC-GC, Comprehensive GCxGC en Sequential GC-GC vir geselekteerde petrochemiese toepassings. Die fundamentele teoretiese aspekte van die tegnieke word bespreek en drie analitiese toepassings word beskryf. Oksigenate word so ver moontlik verwyder uit C10 – C13 paraffien-voerstrome, wat gebruik word in die vervaardiging van liniêre alkielbenzene, aangesien dit deaktiverend kan inwerk op alkileringskataliste. Die oorblywende oksigenate kan uit honderde komponente bestaan sodat analise van individuele komponente tot op lae ng/g vlakke nodig is. Heart-cut GC-GC word gebruik om die skeiding en verryking van die oksigenate in die alkileringsvoerstroom te illustreer. Die stationêre fase in die eerste-dimensie kolom is so gekies dat skeiding tussen oksigenate en koolwaterstowwe verkry word. Met herhaalde inspuitings verhoog die oksigenaat-konsentrasie op die cryo val en - na voldoende verryking - word die val verhit en die oksigenate geanaliseer op die tweede dimensie kolom. Die skeiding en analises verkry met Comprehensive GCxGC en Sequential GC-GC word vergelyk vir die chemiese klasse-skeiding van die alkileringsvoer (voor verwydering van oksigenate). Sikliese alkohole kan voorkom in detergent-alkohole vervaardig vanaf FT voerstrome. Dit word as onsuiwerhede beskou aangesien dit die fisiese eienskappe van die finale produkte beïnvloed. Die sikliese en nie-sikliese alkohole se kookpunte en polariteite is baie naby aanmekaar sodat skeiding van individuele komponente moeilik verkry word. Comprehensive GCxGC en Sequential GC-GC word evalueer vir die skeiding van die alkohol. Die studie toon aan dat albei die tegnieke skeiding gee van die chemiese komponent-klasse maar dat die hoë-resolusie tweede-dimensie kolom en die optimisering van die experimentele kondisies van die Sequential GC-GC sisteem beter skeiding van individuele komponente gee. Die uitsonderlike skeidingsvermoë van die drie multidimensionele tegnieke, Heart-cut GC-GC, Comprehensive GCxGC en Sequential GC-GC word geïllustreer in die studie. Elke tegniek het sy eie voordele, nadele en unieke toepassings en die drie tegnieke behoort as komplementêre eerder as kompeterende tegnieke gebruik te word.

Thesis (PhD)--University of Stellenbosch, 2011. / ENGLISH ABSTRACT: The analysis of Fischer–Tropsch–derived (FT–derived) synthetic crude and derived products is very challenging because of the highly complex nature of these products. In this study, the use of comprehensive multidimensional gas chromatography (GCxGC) with time-of-flight mass spectrometry (TOF-MS) and flame ionisation detection (FID) was investigated for the analysis of these products and the technique was found to be invaluable for the analysis of these complex mixtures. The compositions of FT synthetic crude, produced at low temperature (LT–FT) and high temperature (HT–FT) processes were compared and the effect that changes in FT reaction temperature has on product formation was investigated. Results for conventional onedimensional GC (1D-GC) and GCxGC were compared. It was found that conventional 1D–GC does not have sufficient peak capacity to separate the thousands of compounds in the HT FT products. GCxGC provides a huge peak capacity of tens-of-thousands to separate highly complex mixtures. Structured chromatograms, where groups of compounds with similar properties are grouped together, aid in peak identification. Moreover, sensitivity at low microgram per milliliter levels is obtained. These attributes enabled accurate analysis of various complex feed and product streams in the FT refinery, and also various final fuel products. The use of GCxGC alone was demonstrated, and also combined with high performance liquid chromatography (HPLC), supercritical fluid chromatography (SFC) and nuclear magnetic resonance (NMR) when even more separation power was needed. HPLC–GCxGC enabled the separation of alkene and cyclic alkane compound classes in oligomerisation products. These compound classes have similar mass spectra, elute in adjacent regions and co–elute even to some extent on the GCxGC contour plot, making differentiation difficult. SFC is a good replacement for HPLC for these applications because it does not use solvents as mobile phases. CO2 is easily evaporated after the separation and does not interfere with the GCxGC separation of the analytes. SFC is also a very good technique to separate the compound classes of alkanes, alkenes, aromatics and oxygenates, and is therefore highly complementary to GCxGC. The combination of GCxGC with NMR data was also found to be very valuable for the identification of branched alkane isomers in LT–FT diesels. GCxGC provides excellent separation of individual compounds but the identification of isomers (except for mono–methyl branching) is difficult because the mass spectra of most of these isomers are similar and not all compounds are in the mass spectral libraries. NMR, on the other hand, is able to distinguish between the individual types of branched isomers but has limited separation power for the complex mixtures. By combining the two techniques, the best of both was obtained. The study found GCxGC to be invaluable for the analysis of the highly complex FT–derived products, while its combination with other techniques such as HPLC, SFC and NMR provided even more separation power. / AFRIKAANSE OPSOMMING: Die hoogs komplekse samestelling van sintetiese ru–olie en afgeleide produkte, afkomstig van Fischer–Tropsch (FT) sintese, bied groot uitdagings aan die analis. Die studie het die gebruik van GCxGC met ’n TOF-MS en FID bestudeer vir die analise van FT produkte en het bevind dat die tegniek van onskatbare waarde is vir die analise van die hoogs komplekse mengsels. Die samestellings van produkte van lae- en hoë-temperatuur FT prossesse is vergelyk en die effek van ’n verhoging in die reaksie–temperatuur op die produk samestelling is ondersoek. Resultate vir 1D–GC and GCxGC is vergelyk en dit was duidelik dat 1D-GC nie naastenby voldoende piekkapasiteit het om al die komponente van die produkte wat tydens die hoëtemperatuur prosses gevorm word, te kan skei nie. Die GCxGC se piekkapasiteit daarteenoor is in die orde van tienduisende wat die skeiding van hoogs komplekse mensels moontlik maak terwyl die tegniek hoogs gestruktureerde kontoerplotte verskaf wat help met identfikasie van komponente. Die tegniek is verder ook baie sensitief en kan komponente op lae μg/mL vlakke waarneem. Hierdie eienskappe het akkurate analise van verskeie FT produkstrome moontlik gemaak. Die kombinasie van GCxGC met HPLC, SFC en KMR het selfs meer skeidingskrag verskaf waar nodig. HPLC–GCxGC het die skeiding van alkene en sikliese alkane moontlik gemaak. Hierdie komponent klasse se massaspektra is feitlik dieselfde en terselfdertyd elueer die twee groepe reg langs mekaar, en oorvleuel soms selfs tot ’n mate, op die GCxGC kontoerplot, sodat dit moeilik is om daartussen te onderskei. SFC is ’n goeie alternatief vir HPLC in meeste toepassings aangesien die tegniek net CO2 gebruik, wat maklik verdamp by kamertemperatuur en nie oplosmiddels gebruik wat se pieke steur met die van die laekookpunt komponente op die GCxGC kontoerplot nie. Skeidings van die komponentgroepe alkane, alkene, aromate en oksigenate is moontlik met SFC en daarom komplimenteer dit die GCxGC skeiding goed aan. Die kombinasie van GCxGC met kern–magnetiese resonansie (KMR) is van waarde gevind om die verskillende tipes vertakkings in ’n lae-temperatuur FT diesel te identifiseer. GCxGC verskaf uitstekende skeiding van individuele komponente maar die identifikasie van die verskilende isomere, behalwe vir die mono-metiel vertakkings, is moeilik aangesien die massaspektra van baie van die komponente soortgelyk is en die komponente nie in die massa spektrum–biblioteke voorkom nie. KMR, aan die ander kant, kan tussen die individuele vertakkings onderskei maar het beperkte skeidingskrag vir komplekse mensels. Deur die twee tegnieke te kombineer is die beste van albei tegnieke bekom. Die studie het bevind dat GCxGC van onskatbare waarde is vir die analise van die komplekse sintetiese FT produkte terwyl die kombinasie met ander tegnieke soos HPLC, SFC and KMR selfs meer skeidingskrag verskaf.

A potential route for converting different carbon sources (coal, natural gas and biomass) into synthetic fuels is the transformation of these raw materials into synthesis gas (CO and H2), followed by a catalytic step which converts this gas into the desired fuels. The present thesis has focused on two catalytic steps: Fischer-Tropsch synthesis (FTS) and methanation. The Fischer-Tropsch synthesis serves to convert synthesis gas into liquid hydrocarbon-based fuels. Methanation serves instead to produce synthetic natural gas (SNG). Cobalt catalysts have been used in FTS while nickel catalysts have been used in methanation.             The catalyst lifetime is a parameter of critical importance both in FTS and methanation. The aim of this thesis was to investigate the deactivation causes of the cobalt and nickel catalysts in their respective reactions.             The resistance to carbonyl-induced sintering of nickel catalysts supported on different carriers (γ-Al2O3, SiO2, TiO2 and α-Al2O3) was studied. TiO2-supported nickel catalysts exhibited lower sintering rates than the other catalysts. The effect of the catalyst pellet size was also evaluated on γ-Al2O3-supported nickel catalysts. The use of large catalyst pellets gave considerably lower sintering rates. The resistance to carbon formation on the above-mentioned supported nickel catalysts was also evaluated. Once again, TiO2-supported nickel catalysts exhibited the lowest carbon formation rates. Finally, the effect of operating conditions on carbon formation and deactivation was studied using Ni/TiO2 catalysts. The use of higher H2/CO ratios and higher pressures reduced the carbon formation rate. Increasing the temperature from 280 °C to 340 °C favored carbon deposition. The addition of steam also reduced the carbon formation rate but accelerated catalyst deactivation.             The decline in activity of cobalt catalysts with increasing sulfur concentration was also assessed by ex situ poisoning of a cobalt catalyst. A deactivation model was proposed to predict the decline in activity as function of the sulfur coverage and the sulfur-to-cobalt active site ratio. The results also indicate that sulfur decreases the selectivity to long-chain hydrocarbons and olefins. / <p>QC 20160817</p>

ABSTRACT Nanostructured silica materials were synthesised by the sol-gel process using simple hydroxyacids as template precursors, and these materials were employed as supports for a low temperature iron Fischer-Tropsch (FT) catalyst. Thus, this thesis is divided into two parts: (I) the synthesis of nanostructured silica gels, and (II) their use as catalyst supports in the FT reaction. PART I The effects of synthesis conditions, acidic and basic template precursors and their amounts, synthesis temperature, duration of hydrolysis and ageing, solvent concentration, organic co-solvent, and the synthesis procedure used on the morphology of the silica materials were studied. The synthesised silica gels were characterised by TEM, SEM, BET, TGA, and XRD. Mixtures of different morphologies were obtained with all the hydroxyacids used and the studies revealed that the morphology of the resultant silica gels was largely determined by the type of the hydroxyacid used. The use of oxalic acid produced materials with 4-9 % micropores and a mixture of meso- and macropores mainly consisting of hollow tubes and hollow spheres; the use of D-gluconic and L-tartaric acids produced mesoporous materials mainly consisting of hollow spheres and sheets with folds, respectively; while the use of stearic and cinammic acids produced macroporous materials mainly consisting of solid spheres and undeveloped particles, respectively. The silica gels formed were found to be amorphous in nature, despite the different morphologies that existed in them, and were also thermally stable.Studies involving the use of oxalic and D-gluconic acids showed that the key to the shape of the resultant morphologies resided in the shape of the template crystals formed in solution under specific synthesis conditions. The template shape depended on the type of the template precursor (i.e. both the acid and the base) and its amount. It was also observed that under certain conditions, both at elevated temperatures (≥ 55 oC) and at high water concentrations (> 50 %), the template dissolved and this led to low yields of shaped morphologies (i.e. hollow spheres and tubes). The solvent concentration to produce a maximum tube yield (in the case of oxalic acid) and hollow sphere yield (in the case of D-gluconic acid) was found to require about 25- 50 % water. Very well-developed tubes were also obtained at this concentration (i.e. with oxalic acid). Long hydrolysis and ageing times (i.e. > 2 h) of the sols and gels, respectively, resulted in the formation of surface attached colloidal particles and of tubes and hollow spheres with decreased wall thicknesses. Pre-formation of the template prior to addition of TEOS produced materials with lower surface areas, higher tube yields and bigger tube sizes when compared with materials synthesised by forming the template together with the silica gel. PART II Two types of silica gels were used as supports for an iron FT catalyst; the nanostructured silica gels (tubes with surface area 109 m2/g and spheres with surface area 245 m2/g ) and a commercial silica gel (Davisil silica, surface area 273 m2/g - consisting of undeveloped particles). The effect of varying the potassium promotion levels and of the support morphology on the catalyst activity and selectivity in the FT reaction was studied at 250 oC, in a slurry operated CSTR.It was observed that an increase in the potassium loading up to 0.5 wt % in the Davisil silica catalyst led to a decrease in the catalyst FT and water gas shift (WGS) activity, and methane selectivity. However, the efficiency of the catalyst to produce hydrocarbons increased with an increase in potassium loading up to 0.5 wt %. Increasing the potassium level up to 0.9 wt % led to a slight increase in both the catalyst activity and methane selectivity, and a decrease in the catalyst efficiency. For the silica tubes catalyst, increasing the potassium loading to 0.5 wt % led to an increase in the catalyst activity and methane selectivity, while increasing the potassium level up to 0.9 wt % led to a decrease in the catalyst activity. For both supports, increasing the potassium loading led to an increase in the selectivity towards high molecular weight hydrocarbons, olefins (relative to paraffins) and terminal olefins (relative to internal olefins). While the Davisil silica and the silica tube catalysts remained more or less stable throughout the reaction, the activity of the silica spheres catalyst declined rapidly with time. The nanostructured silica gel supported catalysts both showed higher activities and methane selectivities, but lower efficiencies when compared to the Davisil silica catalyst. Although the selectivity of all three catalysts towards olefins were similar, their selectivity towards high molecular weight hydrocarbons decreased in the order Davisil silica > silica spheres > silica tubes. Elongated needlelike Fe nanoparticles (NPs) were obtained in the silica tubes catalyst, semi hexagonal Fe NPs were formed in the silica spheres catalyst, while the Fe NPs could not be distinguished from the support in the Davisil silica catalyst. After the reaction, the surface areas of all three catalysts were found to have decreased and the catalysts to have sintered. The nanostructured silica supported catalysts showed the presence of Fe nanozones surrounded by a layer of amorphous carbon, while only agglomerated particles of Fe and some carbon rich regions were observed in the Davisil silica catalyst. No evidence of alteration of the morphology of the nanostructured silica supports was observed after the reaction.

School of Chemical and Metallurgical Engineering, Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, South Africa 26 February 2016 / Many reports in the open literature have focused on Fischer-Tropsch (FT) kinetics, yet none of them appear to be able to explain FTS completely. Few of the FT models consider the production of olefins and paraffins separately. To study whether the selectivity to olefins and paraffins follows similar trends and if kinetics alone suffices to explain FT phenomena, a series of FT experiments were conducted in a fixed bed reactor loaded with 10% Co/TiO2. FT feeds were periodically switched from syngas to syngas + N2 by adjusting the total reactor pressure so that the reactant partial pressures (PCO and PH2) remained constant. During the initial deactivation (the first 1200 hours), it was found that the formation rates of olefins remained fairly constant (in some cases they increased) while those of paraffins decreased. This indicates the deactivation is mainly caused by the decrease in the paraffin formation rate. Currently, none of the published kinetic models can explain the phenomenon that the decay of the reaction rates of olefins and paraffins were not the same during the deactivation. At steady state (1055 to 2700 hours, overall reaction rate fairly constant), adding extra N2 decreased the selectivity to the light hydrocarbons. These results suggest that by feeding the extra N2 there could be an increase in selectivity and formation rates to long chain hydrocarbons (C5+). Plotting molar ratios of paraffin to olefin (P/O) with carbon number n+1 versus the ratio with carbon number n revealed linear relationships which are independent of feed gases, catalyst activity and reaction temperature. These results imply that product distributions might be determined by some sort of equilibrium. Another plot of normalised mole fractions of CnH2n, Cn+1H2n+2, and CnH2n+2 in ternary diagrams showed that after disturbances these product distributions tended to stable points. It is suggested that this could be due to slow changes in the liquid composition after the disturbances. Although not all the results are explained, the researcher emphasises that normal kinetics alone cannot explain these results completely. There might be factors, iii including vapour-liquid equilibrium or reactive distillation, which are worthy of consideration to explain FTS. / MT2016

The use of biomass as a potential feedstock for the production of liquid hydrocarbon fuels has been under investigation in the last few decades. This paper discusses a preliminary design and a feasibility study of producing liquid hydrocarbon fuels from biomass through a combined biochemical and thermochemical route. The process involves anaerobic digestion (AD) of the biodegradable portion of the biomass to produce methane rich gas. The methane rich biogas stream is purified by removing contaminants and upgraded to liquid hydrocarbon fuel in a gas to liquid facility (GTL) via thermochemical conversion route. The biogas conversion involves two major steps: tri-reforming step to produce syngas (a mixture of CO and H2), and Fischer-Tropsch Synthesis (FTS) step to convert the syngas to a spectrum of hydrocarbons. Separation and upgrading of the produced hydrocarbon mixture allows production of synthetic transportation fuels. AD is ranked as one of the best waste management options as it allows for: energy recovery, nutrient recovery, and reduction in greenhouse gases emission. A detailed process modeling of the process was carried out using ASPEN Plus process design software package. Data for the process was based on literature on AD combined with laboratory results on the biogas to liquid conversion process. The composition of the final liquid hydrocarbon from the ASPEN model has been compared to the composition of commercial diesel fuel, and results have shown good agreement. As a result, the most current commercial diesel prices were used to evaluate the potential revenue from selling the product in the open market. The total capital investment to construct the plant with a capacity of handling 100,000 ton per year of wet biomass is $16.2 million with a potential of producing 2.60 million gallons of diesel. The base case feedstock is corn stover. The annual operating cost to run the plant is estimated to be $8.81 million. An annual revenue from selling the diesel product is estimated to be $14.6 million taking into account a green energy incentive of $3.00/gallon of diesel sold. The net present worth at the end of the plant life is $8.76 million with a discounted cash flow of return of 26.2%. The breakeven cost of diesel is determined to be $4.34/gallon assuming no tipping fees are charged for handling the waste. Sensitivity analyses results concluded that the profitability of the process is most sensitive to variation in diesel selling price. Based on these results, it can be concluded that the process is profitable only if incentives are provided for renewable fuels due to the current low prices of fossil fuels.

Ce travail concerne la mesure et la caractérisation du transfert thermique à la paroi externe d'un faisceau de tube de refroidissement inséré dans des colonnes à bulles type " slurry ". La valeur du coefficient de transfert de chaleur est estimée à partir des équations de la chaleur. Une colonne de 0,15 m de diamètre et de 4 m de haut, équipée de deux tubes en U (3 cm de diamètre externe), a été utilisée pour mettre au point la métrologie nécessaire. L'eau a servi de fluide de refroidissement. Le mélange diphasique air-huile Syltherm XLT®, puis le mélange triphasique air-huile Syltherm XLT®-microbilles d'alumine poreuses (dS ~ 80 μm), ont servi de fluides modèles. L'incertitude de nos mesures a été estimée à environ 8 %. En système diphasique, les variations du coefficient de transfert de chaleur avec la vitesse superficielle du gaz ont pu être corrélées par une loi semblable à celle de Deckwer (1980). Cependant, la valeur de la constante de corrélation semble dépendre de l'orientation du faisceau de tubes par rapport à l'axe de la colonne. Un tel comportement n'a jamais été rapporté dans la littérature. L'écart du faisceau à un faisceau idéal (i.e. parfaitement droit et symétrique) peut être un paramètre crucial pour le transfert de chaleur. En système triphasique, la valeur du coefficient ne varie pas de façon significative jusqu'à une concentration massique d'environ 18,8 %, avant de diminuer d'environ 10 % pour une concentration massique de 21,3 %. Ce résultat est surprenant. Les variations rapportées dans la littérature sont en effet souvent contradictoires, mais toujours continues dans la gamme de concentrations testée. La métrologie mise au point a été implantée dans une colonne de 1 m de diamètre et de 5 m de haut, équipée de 24 tubes en U (6 cm de diamètre externe). Celle-ci est jugée représentative d'un réacteur pour le procédé Fischer-Tropsch. Les premiers résultats indiquent que la caractérisation thermique de l'installation sera plus délicate que pour la petite colonne

Today, a majority of the world’s energy need is supplied through sources that are finite and, at the current usage rates, will be consumed shortly. The high energy demand and pollution problems caused by the widespread use of fossil fuels make it increasingly necessary to develop renewable energy sources of limitless duration with smaller environmental impact than the traditional energy sources. Three fuels – rapeseed methyl ester (RME), Fischer-Tropsch (FT) diesel and FT jet fuel – derived from biomass, coal or gas were evaluated in this project. The fuel properties evaluated are in most cases listed in standards, often with recommendations, developed for biodiesel, petroleum diesel and jet fuel. Biodiesel is monoalkyl esters, e.g. RME, produced by transesterification of triglycerides in vegetable oil and an alcohol to esters and glycerin. This produce a fuel that is suitable as a direct substitution for petroleum diesel. Biodiesel may be used in pure form or in a blend with petrodiesel. Oxidative degradation and weak low temperature performance of biodiesel are properties of concern when substituting petrodiesel with biodiesel, as was shown in this project. The experiments show that oxidative stability can be improved with a synthetic antioxidant, e.g. butylated hydroxytoluene (BHT). The FT process converts syngas (a mixture of hydrogen and carbon monoxide) to a range of hydrocarbons. Syngas can be generated from a variety of carbon sources, e.g. coal, natural gas and biomass. The high-temperature (300-350 °C) FT process with iron-based catalysts is used for the production of gasoline and linear low molecular mass olefins (alkenes). The lowtemperature (200-240 °C) FT process with either iron or cobalt catalysts is used for the production of high molecular mass linear waxes. By applying various downstream processes, fuels suitable for substitution of petrodiesel and conventional jet fuel can be obtained. The FT fuels have lower densities than the conventional fuels. However, conclusions from this project are that most of the properties of FT fuels are better, or equal, than conventional petroleum fuels.

<p>Today, a majority of the world’s energy need is supplied through sources that are finite and, at the current usage rates, will be consumed shortly. The high energy demand and pollution problems caused by the widespread use of fossil fuels make it increasingly necessary to develop renewable energy sources of limitless duration with smaller environmental impact than the traditional energy sources.</p><p>Three fuels – rapeseed methyl ester (RME), Fischer-Tropsch (FT) diesel and FT jet fuel – derived from biomass, coal or gas were evaluated in this project. The fuel properties evaluated are in most cases listed in standards, often with recommendations, developed for biodiesel, petroleum diesel and jet fuel.</p><p>Biodiesel is monoalkyl esters, e.g. RME, produced by transesterification of triglycerides in vegetable oil and an alcohol to esters and glycerin. This produce a fuel that is suitable as a direct substitution for petroleum diesel. Biodiesel may be used in pure form or in a blend with petrodiesel. Oxidative degradation and weak low temperature performance of biodiesel are properties of concern when substituting petrodiesel with biodiesel, as was shown in this project. The experiments show that oxidative stability can be improved with a synthetic antioxidant, e.g. butylated hydroxytoluene (BHT).</p><p>The FT process converts syngas (a mixture of hydrogen and carbon monoxide) to a range of hydrocarbons. Syngas can be generated from a variety of carbon sources, e.g. coal, natural gas and biomass. The high-temperature (300-350 °C) FT process with iron-based catalysts is used for the production of gasoline and linear low molecular mass olefins (alkenes). The lowtemperature (200-240 °C) FT process with either iron or cobalt catalysts is used for the production of high molecular mass linear waxes. By applying various downstream processes, fuels suitable for substitution of petrodiesel and conventional jet fuel can be obtained. The FT fuels have lower densities than the conventional fuels. However, conclusions from this project are that most of the properties of FT fuels are better, or equal, than conventional petroleum fuels.</p>

Bioenergy has the potential to reduce the world's dependence on fossil fuels, and to decrease the CO2 emissions due to fossil combustion. Lignocellulosic and algae biomass have been presented as promising feedstocks for bioenergy production. In this study, a comparative Life Cycle Assessment (LCA) has been developed to evaluate the environmental impacts associated with different energy products via different routes across the whole life of algal and lignocellulosic bioenergy. Results were compared per energy basis, the production of 1 million BTU of energy products. For the development of the comparative algae biomass conversion LCA, algal biomass was converted to liquid biofuels via a thermochemical gasification and Fisher-Tropsch Synthesis (FTS) process; and to electricity and heat via anaerobic digestion and combined heat and power (CHP) process. Overall results from the algae biomass conversion LCA showed that the process that converts algae biomass through anaerobic digestion and CHP process to electricity and heat had the highest overall environmental impact. Results also showed that the impact categories that appear to contribute the most to the overall impacts are ecotoxicity, human health non-cancer, and human health cancer. For the development of the comparative lignocellulosic biomass conversion LCA, lignocellulosic biomass was converted to ethanol and higher alcohols through thermochemical gasification and alcohol synthesis process, to liquid biofuels via thermochemical gasification and FTS process, and to liquid biofuels via a thermochemical gasification and FTS process that uses methane. Overall results from the lignocellulosic biomass conversion LCA showed that the process that converts lignocellulosic biomass into alcohols has the highest overall environmental impact. Results also showed that the impact categories that appear to contribute the most to the overall impacts are ecotoxicity, human health non-cancer, human health cancer, and global warming. This study determined that cultivated algae biomass feedstock has much higher environmental impacts compared with lignocellulosic biomass feedstock from forestation and agriculture byproducts. It was also concluded that thermochemical gasification and FTS process showed higher efficiency when converting biomass to bioenergy. In addition, the five biomass to bioenergy conversion pathways used in the development of this LCA study were compared. Results showed that the pathway with lignocellulosic biomass (feedstock), thermochemical gasification and alcohol synthesis process (conversion process), and ethanol and higher alcohols (energy products) has the largest environmental impact.