Osseointegration, or the direct integration of an implant into bone tissue, is necessary for implant success. Titanium is commonly used clinically in dental and orthopaedic implants because of its passivating oxide layer, which facilitates osseointegration, and its mechanical properties such as a modulus of elasticity similar to bone. Diverse studies have shown that surface microtopography, chemistry, and surface energy affect osteoblast behavior. The problem with these studies is that they access the average behavior of a culture in response to a substrate and not the behavior of individual cells. The objective of this study was to develop a method for correlating the behavior of individual cells with the characteristics of the surface underneath them. More specifically, this work developed a method to correlate integrin beta-1 (β1) expression with the surface characteristics under individual cells. Integrins are cell surface receptors that bind to specific proteins in the extracellular matrix adsorbed on the implant surface. Previous work has shown that expression of certain integrins is increased when osteoblasts on titanium substrates develop a more differentiated phenotype, and that integrin β1 is necessary for osteoblast response to roughness on titanium substrates. This study used molecular beacons specific to integrin β1 to quantify integrin β1 expression of MG63 cells cultured on titanium disks. A template was designed to coordinate the location of cells using fluorescence microscopy and scanning electron microscopy (SEM) in reference to laser etchings on the disks. After live cell imaging, cells were fixed, dried, and critical point dried for focused ion beam (FIB) milling. Transmission electron microscopy (TEM) sections of cells identified with high and low integrin β1 molecular beacon intensity were milled, and cells with high and low integrin β1 molecular beacon intensity were also serial sectioned. While our TEM results were inconclusive, SEM images from serial sectioning showed contact points between the cell body and the substrate, consistent with previous results. Cells cultured on pretreatment (PT) or sandblasted acid etched (SLA) titanium surfaces were also serial sectioned, showing that cells on SLA surfaces have more regions of contact between the cells and the substrate than cells on PT surfaces. This work is significant as it is the first study to develop a method to correlate individual cell behavior with the substrate surface characteristics under the individual cells. Previous studies have reported the average cell behavior in response to their substrates, while this work allows for the study of substrate surface characteristics that positively affect integrin β1 expression in individual cells. Further optimization of the fluorescence imaging process and FIB milling process could be done, and the method developed in this study could be used in future studies to investigate surface characteristics after using other fluorescent analyses of cell behavior, such as immunocytochemistry.

The ability to generate three dimensional (3D) microstructures in solids is of great importance in understanding their true nature, as it eliminates speculation about the spatial distribution of features associated with conventional two dimensional (2D) imaging techniques. There are several recently-developed 3D techniques for determining the spatial distribution of microstructural features, each with a given resolution. There is considerable interest in the development of a specific serial sectioning methodology, termed 3D electron backscatter diffraction (3D-EBSD), which combines a focused ion beam (FIB) with EBSD interfaced to a field emission gun scanning electron microscope. Here, FIB is used as a serial sectioning device for cutting parallel slices of single- and multi-phase materials with a site-specific accuracy of up to 50 nm. Each consecutive slice is mapped by EBSD and the complete dataset combined using advanced computer algorithms to generate a volume of a material whereby the true crystallographic features can be analyzed at submicron resolution. The aims of the thesis was to develop 3D-EBSD into a powerful materials analysis tool and use it to resolve several issues concerning the nature of the deformed state and the nucleation and the growth behaviour of recrystallizing grains. The study commenced with an investigation into the effect of material type (restricted to face centred cubic AI, Cu and Au metallic crystals), FIB milling conditions and EBSD software variables on the quality of EBSD patterns generated on ion-milled surfaces of these materials. The effect of material type on EBSD pattern quality following FIB milling was found to be significant with relatively poor quality EBSD patterns obtained for metals of low atomic number. It was demonstrated, particularly for the high atomic number metals, that moderate FIB milling currents (~1-5nA) generated good quality EBSD maps from a given ion-milled surface. This preliminary work was necessary for balancing the time required for serial sectioning during 3D-EBSD and the generation of sufficient quality EBSD maps from each ion-milled surface. The outcomes of this investigation were applied to two major 3D-EBSD investigations on the microstructural and crystallographic characteristics of: (i) deformation features generated in a cold rolled interstitial free (IF) steel, with particular emphasis on the formation of microbands; and (ii) recrystallization of a cold rolled nickel alloy containing coarse (>1 ??m) silica particles, with particular attention given to the generation of particle deformation zones and their influence on nucleation and growth of recrystallizing grains including particle stimulated nucleation (PSN), twin formation during PSN and the growth behaviour of various types of grain boundary into the deformation microstructure. The foregoing 3D-EBSD studies were significant as they revealed various microstructural and crystallographic features not usually clearly evident in conventional 2D micrographs obtained by either EBSD or optical metallography. For example, the technique demonstrated that microbands in cold rolled IF steel consist of irregular curved surfaces that reconcile findings that microbands straight and aligned parallel to slip planes when viewed in normal direction-rolling direction sections but are wavy in transverse direction-rolling direction sections. Three slip planes were found within the angular range of the curved surface of the microband, which indicates that multiple slip planes are operative during deformation. The work also showed the influence of particle diameter on the misorientations generated within particle deformation zones and clearly showed that particle stimulated nucleation (PSN) occurred at particles greater than 1.5-2 ??m. It was observed that PSN in the nickel sample also generates contiguous grains separated by both coherent and incoherent twin boundaries and, on further growth of these grains into the matrix, the coherent boundary dominates and remains parallel to the primary growth direction of the grains.

A challenge exists for understanding the origin of color for structurally colored, 3-dimensional bioorganic nanostructures, such as the scales of butterflies, beetles, and moths. Complex, hierarchical structures found within such scales create the overall scale appearance. The controlled alteration of color through material deposition and the addition of new optical functionalities to such structures are other areas of scientific interest. This dissertation addresses these challenges with a first-of-its-kind, systematic isolation (deconstruction) of scale component nanostructures, followed by evaluation of optical property/structure correlations. The additive deposition (constructive alteration) of emissive materials to structurally-colored templates complements this deconstructive approach towards understanding the origin of color in butterfly scales. Discoveries made through this work may help advance the bioinspired design of synthetic optical structures and subsequent color control through the addition of multilayered, emissive optical components.

Du fait de leur facilité de fabrication et de leurs propriétés physiques uniques, les nanofils (NFs) de semi-conducteurs présentent des potentialités d’application importantes elles pouvaient être comme briques élémentaires de nombreux dispositifs nano- et opto-électroniques. Différents procédés de fabrication ont été développés pour fabriquer et organiser ces nanofils en épitaxie sur silicium. Cependant, un des principaux problèmes réside dans le manque de reproductibilité des NFs produits naturellement. Pour obtenir un meilleur contrôle de leur périodicité, localisation, forme et taille, différents types de gravure ont été mis au point. Aujourd’hui, des incertitudes importantes persistent quant à leurs propriétés fondamentales, en raison d’un manque de corrélation entre les propriétés électroniques et optiques et les détails microscopiques (composition, structure, chimie ...etc.). L’objectif de ce travail est de développer deux types de procédés de fabrication : le premier "top-down" est basé sur la nanogravure directe par faisceau d’ions focalisés (FIB)de couches bi-dimonsionnelles de SiGe. Ce procédé permet de contrôler la taille des NFs, les déformations, et leur localisation précise. Il permet de fabriquer des réseaux de larges piliers. Les NFs réalisés par cette technique sont peu denses et de diamètre important. Le second procédé est de type "Bottom-Up" ; il s’appuie sur la croissance VLS à partir de catalyseurs métalliques (AuSi). Les NFs réalisés ont étudiés à l’échelle locale afin de mesurer la taille moyenne de contrainte ainsi que leur effet sur le confinement quantique et sur la structure de bande des NFs. / SiGe/Si core/shell nanowires (NWs) and nanodots (NDs) are promising candidates for the future generation of optoelectronic devices. It was demonstrated that the SiGe/Si heterostructure composition, interface geometry, size and aspect ratios can be used to tune the electronic properties of the nanowires. Compared to pure Si or Ge nanowires, the core-shell structures and exhibit extended number of potential configurations to modulate the band gap by the intrinsic strain. Moreover, the epitaxial strain and the band-offsets produce a better conductance and higher mobility of charge carriers. Recent calculations reported that by varying the core-shell aspect ratio could induce an indirect to direct band gap transition. One of the best configurations giving direct allowed transitions consists of a thin Si core embedded within wide Ge shell. The Germanium condensation technique is able to provide high Ge content (> 50%) shell with Si core whom thickness of core and shell can be accurately tuned. The aim of this work is to develop two types of synthesis processes: the first "top-down" will be based on direct nanoetching by focused ion beam (FIB) of 2D SiGe layer. This process allows the control of the size of NWs, and their precise location. The NWs achieved by this technique are not very dense and have a large diameter. The second processes called "bottom-up"; are based on the VLS growth of NWs from metal catalysts (AuSi). Grown NWs have been studied locally in order to measure the mean size and the strain and their effects on the quantum confinement and band structure of NWs.

No description available.

An experimental method was further developed to quantify the anisotropy of multi-site fatigue crack initiation behaviors in high strength Al alloys by four-point bend fatigue testing under stress control. In this method, fatigue crack initiation sites (fatigue weak-links, FWLs) were measured on the sample surface at different cyclic stress levels. The FWL density in an alloy could be best described using a three-parameter Weibull function of stress, though other types of sigmoidal functions might also be used to quantify the relationship between FWL density and stress. The strength distribution of the FWLs was derived from the Weibull function determined by fitting the FWLs vs. stress curve experimentally obtained. As materials properties, the FWL density and strength distribution could be used to evaluate the fatigue crack nucleation behaviors of engineering alloys quantitatively and the alloy quality in terms of FWL density and strength distribution. In this work, the effects of environment, types of microstructural heterogeneities and loading direction on FWLs were all studied in detail in AA7075-T651, AA2026-T3511, and A713 Al alloys, etc. It was also found that FWLs should be quantified as a Weibull-type function of strain instead of stress, when the applied maximum cyclic stress exceeded the yield strength of the tested alloys. In this work, four-point bend fatigue tests were conducted on the L-T (Rolling-Transverse), L-S (Rolling-Short transverse) and T-S planes of an AA7075-T651 alloy plate, respectively, at room temperature, 20 Hz, R=0.1, in air. The FWL populations, measured on these surfaces, were a Weibull-type function of the applied maximum cyclic stress, from which FWL density and strength distribution could be determined. The alloy showed a significant anisotropy of FWLs with the weak-link density being 11 mm-2, 15 mm-2 and 4 mm-2 on the L-T, L-S and T-S planes, respectively. Fatigue cracks were predominantly initiated at Fe-containing particles on the L-T and L-S planes, but only at Si-bearing particles on the T-S plane, profoundly demonstrating that the pre-fractured Fe-containing particles were responsible for crack initiation on the L-T and L-S planes, since the pre-fracture of these particles due to extensive deformation in the L direction during the prior rolling operation could only promote crack initiation when the sample was cyclically stressed in the L direction on both the L-T and L-S planes. The fatigue strengths of the L-T, L-S and T-S planes of the AA7075 alloy were measured to be 243.6, 273.0 and 280.6 MPa, respectively. The differences in grain and particle structures between these planes were responsible for the anisotropy of fatigue strength and FWLs on these planes. Three types of fatigue cracks from particles, type-I: the micro-cracks in the particles could not propagate into the matrix, i.e., type-II: the micro-cracks were fully arrested soon after they propagated into the matrix, and type-III: the micro-cracks became long cracks, were observed in the AA7075-T651 alloy after fatigue testing. By cross-sectioning these three-types of particles using Focused Ion Beam (FIB), it was found that the thickness of the particles was the dominant factor controlling fatigue crack initiation at the particles, namely, the thicker a pre-fractured Fe-containing particle, the easier it became a type-III crack on the L-T and L-S planes. On the T-S plane, there were only types-I and III Si-bearing particles at which crack were initiated. The type-I particles were less than 6.5 μm in thickness and type-III particles were thicker than 8.3 μm. Cross-sectioning of these particles using FIB revealed that these particles all contained gas pores which promoted crack initiation at the particles because of higher stress concentration at the pores in connection with the particles. It was also found that fatigue cracks did not always follow the any specific crystallographic planes within each grain, based on the Electron Backscatter Diffraction (EBSD) measurement. Also, the grain orientation did not show a strong influence on crack initiation at particles which were located within the grains. The topography measurements with an Atomic Force Microscope (AFM) revealed that Fe-containing particles were protruded on the mechanically polished surface, while the Si-bearing particles were intruded on the surface, which was consistent with hardness measurements showing that Si-bearing particles were softer (4.030.92 GPa) than Fe-containing ones (8.9 0.87 GPa) in the alloy. To verify the 3-D effects of the pre-fractured particles on fatigue crack initiation in high strength Al alloys, rectangular micro-notches of three different types of dimensions were fabricated using FIB in the selected grains on the T-S planes of both AA2024-T351 and AA7075-T651 Al alloys, to mimic the three types of pre-fractured particles found in these alloys. Fatigue testing on these samples with the micro-notches verified that the wider and deeper the micro-notches, the easier fatigue cracks could be initiated at the notches. In the AA2024-T351 samples, cracks preferred to propagate along the {111} slip plane with the smallest twist angle and relatively large Schmid factor. These experimental data obtained in this work could pave a way to building a 3-D quantitative model for quantification of fatigue crack initiation behaviors by taking into account the driving force and resistance to short crack growth at the particles in the surface of these alloys.

Les aciers inoxydables austénitiques métastables sont le siège de différents mécanismes de déformation qui sont à l'origine des propriétés mécaniques qui distinguent ce type d’alliages. Cependant, ces dernières, dépendant de la microstructure locale, sont fortement anisotropes. Par ailleurs, la déformation d'un échantillon massif serait différente de celle obtenue en surface. De ce fait, une étude détaillée trouve tout son intérêt. Le présent travail vise donc à identifier les principaux mécanismes de déformation et de leur évolution progressive, en se basant sur une déformation contrôlée de grains austénitiques individuels par des tests mécaniques de nanoindentation monotoniques et cycliques. Les courbes correspondantes au chargement-déchargement révèlent des informations détaillées sur les propriétés mécaniques sous-jacentes qui pourraient être liées à une étude complète de la structure de déformation en surface et en volume par différentes techniques de caractérisation à une échelle très fine. La déformation en fonction du temps, les phénomènes de transformation de phase réversible sous charge, l'anisotropie cristalline, l'influences de la taille des grains, la transmission de la plasticité et la tenue en fatigue ont été mis en évidence et étudiés / Metastable austenitic stainless steels feature an abundance of different deformation mechanisms, which contribute to the distinguished mechanical properties of these alloys. However, these properties are known to depend on the local microstructure and also are highly anisotropic. Furthermore, deformation is expected to be different for the bulk and the surface of a sample. In this sense, a discrete study is not trivial. The present work aims at investigation of the main deformation mechanisms and their gradual evolution, by employing controlled deformation of individual austenite grains via monotonic and cyclic nanoindentation. The corresponding loading–unloading curves have given extensive information about underlying mechanical properties, which could be related to an exhaustive reconstruction of the deformation substructure, both in surface and bulk, by different small scale characterization techniques. Amongst others, features such as time-dependent deformation, reversible phase transformation under load, crystalline anisotropy and grain size influences, besides plasticity transmission and fatigue behavior have been found and analyzed

No description available.

This thesis focuses on the effect of microstructural variation on the mechanical properties and deformation behavior of ductile iron. To research and determine these effects, two grades of ductile iron, (i) GJS-500-7 and (ii) high silicon GJS-500-14, were cast in a geometry containing several plates with different section thicknesses in order to produce microstructural variation. Microstructural investigations as well as tensile and hardness tests were performed on the casting plates. The results revealed higher ferrite fraction, graphite particle count, and yield strength in the high silicon GJS-500-14 grade compared to the GJS-500-7 grade. To study the relationship between the microstructural variation and tensile behavior on macroscale, tensile stress-strain response was characterized using the Ludwigson equation. The obtained tensile properties were modeled, based on the microstructural characteristics, using multiple linear regression and analysis of variance (ANOVA). The models showed that silicon content, graphite particle count, ferrite fraction, and fraction of porosity are the major contributing factors that influence tensile behavior. The models were entered into a casting process simulation software, and the simulated microstructure and tensile properties were validated using the experimental data. This enabled the opportunity to predict tensile properties of cast components with similar microstructural characteristics. To investigate deformation behavior on micro-scale, a method was developed to quantitatively measure strain in the microstructure, utilizing the digital image correlation (DIC) technique together with in-situ tensile testing. In this method, a pit-etching procedure was developed to generate a random speckle pattern, enabling DIC strain measurement to be conducted in the matrix and the area between the graphite particles. The method was validated by benchmarking the measured yield strength with the material’s standard yield strength. The microstructural deformation behavior under tensile loading was characterized. During elastic deformation, strain mapping revealed a heterogeneous strain distribution in the microstructure, as well as shear bands that formed between graphite particles. The crack was initiated at the stress ranges in which a kink occurred in the tensile curve, indicating the dissipation of energy during both plastic deformation and crack initiation. A large amount of strain localization was measured at the onset of the micro-cracks on the strain maps. The micro-cracks were initiated at local strain levels higher than 2%, suggesting a threshold level of strain required for micro-crack initiation. A continuum Finite Element (FE) model containing a physical length scale was developed to predict strain on the microstructure of ductile iron. The material parameters for this model were calculated by optimization, utilizing the Ramberg-Osgood equation. The predicted strain maps were compared to the strain maps measured by DIC, both qualitatively and quantitatively. To a large extent, the strain maps were in agreement, resulting in the validation of the model on micro-scale. In order to perform a micro-scale characterization of dynamic deformation behavior, local strain distribution on the microstructure was studied by performing in-situ cyclic tests using a scanning electron microscope (SEM). A novel method, based on the focused ion beam (FIB) milling, was developed to generate a speckle pattern on the microstructure of the ferritic ductile iron (GJS-500-14 grade) to enable quantitative DIC strain measurement to be performed. The results showed that the maximum strain concentration occurred in the vicinity of the micro-cracks, particularly ahead of the micro-crack tip. / Denna avhandling fokuserar på effekten av variationer i mikrostrukturen på mekaniska egenskaper och deformationsbeteende hos segjärn. För att undersöka dessa effekter, två olika sorter av segjärn, (i) GJS-500-7 och (ii) högkisellegerad GJS-500-14, gjutits till plattor av olika tjocklekar för att generera mikrostrukturvariationen. Mikrostrukturundersökning, samt drag- och hårdhetsprov gjordes på de gjutna plattorna. Resultaten visade att en högre ferritfraktion, grafitpartikelantal och sträckgräns i den högkisellegerade GJS-500-14-sorten jämfört med GJS-500-7. För att studera förhållandet mellan mikrostrukturell variation och spännings-töjningsbeteendet på makroskala, modellerades detta med hjälp av Ludwigson-ekvationen. De erhållna spännings-töjningsegenskaperna modellerades baserat på mikrostrukturell karaktäristika genom multipel linjärregression och variansanalys (ANOVA). Modellerna visade att kiselhalt, grafitpartikelantal, ferritfraktion och porfraktion var de viktigaste bidragande faktorerna. Modellerna implementerades i ett simuleringsprogram för gjutningsprocessen. Resultatet från simuleringen validerades med hjälp av experimentella data som inte ingick i underlaget för regressionsanalysen. Detta möjliggjorde att prediktera spännings-töjningsbeteendet och dess variation hos gjutna segjärns komponenter med liknande sammansättning och gjutna tjocklekar som användes i denna studie. För att kunna undersöka deformationsbeteendet på mikroskala utvecklades en metod för kvantitativ mätning av töjning i mikrostrukturen, genom DIC-tekniken (digital image correlation) tillsammans med in-situ dragprovning. I denna metod utvecklades en grop-etsningsprocess för att generera ett slumpvis prickmönster, vilket möjliggjorde DIC-töjningsmätning i matrisen och i området mellan grafitpartiklarna med tillräcklig upplösning. Metoden validerades genom benchmarking av den uppmätta sträckgränsen mot materialets makroskopiska sträckgräns mätt med konventionell dragprovning. Det mikrostrukturella deformationsbeteendet under dragbelastning karakteriserades. Under elastisk deformation avslöjade töjningsmönstret en heterogen töjningsfördelning i mikrostrukturen, och bildandet av skjuvband mellan grafitpartiklar. Sprickbildning initierades vid låg spänning och redan vid de spänningsnivåer som ligger vis ”knät” på dragprovningskurvan, vilket indikerar energidissipering genom både begynnande plastisk deformation och sprickbildning. Den lokala töjningen vis sprickinitiering skedde då den lokala töjningen översteg 2%, vilket indikerar att detta skulle kunna vara en tröskelnivå för den töjning som erfordras för initiering av mikro-sprickor. En kontinuum Finita Element (FE) modell utvecklades för att prediktera töjningen hos ett segjärn och dess fördelning i segjärns mikrostruktur. Materialparametrarna för denna modell optimerades genom att anpassa parametrarna i Ramberg-Osgood ekvationen. De predikterade töjningsfördelningarna jämfördes med de experimentell uppmätta töjningsmönstren uppmätta med DIC, både kvalitativt och kvantitativt. Töjningsmönstren överensstämde i stor utsträckning, vilket resulterade i att modellerna kunde anses vara validerade på mikronivå. För att kunna mäta töjningsmönster under dynamiska förlopp på mikronivå utvecklades en metod för att skapa prickmönster och att utföra in-situ CT provning i ett svepeletronmikroskop (SEM). Prickmönstret skapades genom avverkning med en fokuserad jonstråle (FIB), och provades på det ferritiska segjärnet (GJS-500-14 grad). Resultaten visade att maximal töjningskoncentration fanns i närheten av mikrosprickorna, framförallt framför sprickspetsen.

Superaustenitická korozivzdorná ocel typu 22Cr25NiWCoCu určená pro vysokoteplotní aplikace v energetickém průmyslu byla studována za podmínek nízkocyklové únavy při pokojové a zvýšené teplotě. Jednotlivé vzorky byly podrobeny různým zátěžným procedurám, což umožnilo studium materiálové odezvy spolu s mechanismem poškození. Křivky cyklického zpevnění/změkčení, cyklického napětí a Coffin-Mansonovy křivky byly vyhodnoceny. Únavová životnost materiálu byla diskutována s ohledem na uplatňované mechanismy poškození, které se vyvinuly za specifických zátěžných podmínek. Standardní izotermální únavové experimenty byly provedeny při pokojové a zvýšené teplotě. Hysterezní smyčky zaznamenané během cyklického zatěžování byly analyzovány pomocí zobecněné statistické teorie hysterezní smyčky. Pro různé amplitudy napětí byla určena jak distribuce hustoty pravděpodobnosti interních kritických napětí (dále PDF), tak rovněž zjištěn její vývoj během cyklického namáhání. Zjištěné průběhy PDF byly korelovány s vývojem povrchového reliéfu a vnitřního dislokačního uspořádání zdokumentované pro obě teploty pomocí rastrovací elektronové mikroskopie (SEM) vybavené technikou fokusovaného iontového svazku (FIB), která umožnila rovněž efektivní studium nukleace povrchových únavových trhlin. Při cyklickém zatížení při pokojové teplotě byla pozorována lokalizace cyklické plastické deformace do perzistentních skluzových pásů (PSP). V místech, kde tyto PSP vystupují na povrch materiálu byly pozorovány perzistentní skluzové stopy (PSS) tvořené extruzemi a intruzemi. Postupné prohlubování intruzí, zejména na čele nejhlubší intruze, vede k iniciaci únavové trhliny. Odlišný mechanismus tvorby trhlin byl zjištěn při únavové zkoušce při zvýšené teplotě, kde zásadní roli hrál vliv prostředí. Rychlá oxidace hranic zrn a jejich následné popraskání představuje dominantní mechanismus v I. stádiu nukleace trhlin. Aplikace desetiminutové prodlevy v tahové části zátěžného cyklu vedlo k vývoji vnitřního (kavitačního) poškozování. Mechanismy vnitřního poškozování byly studovány na podélných řezech rovnoběžných s napěťovou osou zkušebních vzorků. Trhliny a jejich vztah k hranicím zrn a dvojčat byly studovány pomocí difrakce zpětně odražených elektronů (EBSD). Vliv prodlevy na únavovou životnost byl korelován s vývojem povrchového reliéfu a vnitřního poškození. Vzorky z uvedené oceli byly rovněž podrobeny zkouškám termomechanické únavy (TMF), při nichž se v čase mění jak zátěžná síla tak i teplota. Termomechanické únavové zkoušky v režimu soufázném (in-phase) a protifázném (out-of-phase) byly provedeny jak s prodlevou, tak i bez ní. Ve všech případech bylo pozorováno rychlé cyklické zpevnění bez ohledu na použitou amplitudu deformace, u vzorků testovaných v out-of-phase režimu byla zjištěna tendence k saturaci. Zkoumáním povrchového reliéfu za pomocí technik SEM a FIB byla odhalena přednostní oxidace hranic zrn a následné praskání těchto hranic kolmo k ose zatížení. Prodlevy v cyklech při maximálním napětí vedly ke zvýšení amplitudy plastické deformace a následně ke creepovému poškození ve formě vnitřních kavit a trhlin. Interkrystalické šíření trhlin bylo pozorováno na vzorcích testovaných v režimu in-phase. Vývoj poškození v režimu out-of-phase nebyl principiálně ovlivněn zařazením prodlevy do zátěžného cyklu. Charakteristickým znakem namáhání v režimu out-of-phase je nukleace několika trhlin v homogenní oxidické vrstvě jdoucích napříč zrny kolmo k ose zatěžování.