Reinforced concrete beam-column joints (BCJs) are commonly used in structures such as parking garages, multi-storey industrial buildings and road overpasses, which might be exposed to extreme weathering conditions and the application of de-icing salts. The use of the non-corrodible fiber-reinforced polymer (FRP) reinforcing bars in such structures is beneficial to overcome the steel-corrosion problems. However, FRP materials exhibit linear-elastic stress-strain characteristics up to failure, which raises concerns on their performance in BCJs where energy dissipation, through plastic behaviour, is required. The objective of this research project is to assess the seismic behaviour of concrete BCJs reinforced with FRP bars and stirrups. An experimental program was conducted at the University of Manitoba to participate in achieving this objective. Eight full-scale exterior T-shaped BCJs prototypes were constructed and tested under simulated seismic load conditions. The longitudinal and transversal reinforcement types and ratios for the beam and the columns were the main investigated parameters. The experimental results showed that the GFRP reinforced joints can successfully sustain a 4.0% drift ratio without any significant residual deformation. This indicates the feasibility of using GFRP bars and stirrups as reinforcement in the BCJs subjected to seismic-type loading. It was also concluded that, increasing the beam reinforcement ratio, while satisfying the strong column-weak beam concept, can enhance the ability of the joint to dissipate seismic energy. An analytical investigation was conducted through constructing a finite element model using ANSYS-software. The model was verified against the experimental results in this research. Then, a parametric study was performed on number of different parameters known to affect such joints including column axial load, concrete compressive strength, flexural strength ratio and joint transverse reinforcement. It was concluded that 70% of the column axial load capacity can be recommended as an upper limit to the applied axial loads on the column to avoid damage occurrence within the joint. It was also concluded that a minimum flexural strength ratio of 1.50 is recommended to ensure the strong-column weak-beam mechanism. In addition, a minimum joint transverse reinforcement ratio of 0.60% is recommended to insure that the failure will not occur in the joint zone.

Reinforced concrete beam-column joints (BCJs) are commonly used in structures such as parking garages, multi-storey industrial buildings and road overpasses, which might be exposed to extreme weathering conditions and the application of de-icing salts. The use of the non-corrodible fiber-reinforced polymer (FRP) reinforcing bars in such structures is beneficial to overcome the steel-corrosion problems. However, FRP materials exhibit linear-elastic stress-strain characteristics up to failure, which raises concerns on their performance in BCJs where energy dissipation, through plastic behaviour, is required. The objective of this research project is to assess the seismic behaviour of concrete BCJs reinforced with FRP bars and stirrups. An experimental program was conducted at the University of Manitoba to participate in achieving this objective. Eight full-scale exterior T-shaped BCJs prototypes were constructed and tested under simulated seismic load conditions. The longitudinal and transversal reinforcement types and ratios for the beam and the columns were the main investigated parameters. The experimental results showed that the GFRP reinforced joints can successfully sustain a 4.0% drift ratio without any significant residual deformation. This indicates the feasibility of using GFRP bars and stirrups as reinforcement in the BCJs subjected to seismic-type loading. It was also concluded that, increasing the beam reinforcement ratio, while satisfying the strong column-weak beam concept, can enhance the ability of the joint to dissipate seismic energy. An analytical investigation was conducted through constructing a finite element model using ANSYS-software. The model was verified against the experimental results in this research. Then, a parametric study was performed on number of different parameters known to affect such joints including column axial load, concrete compressive strength, flexural strength ratio and joint transverse reinforcement. It was concluded that 70% of the column axial load capacity can be recommended as an upper limit to the applied axial loads on the column to avoid damage occurrence within the joint. It was also concluded that a minimum flexural strength ratio of 1.50 is recommended to ensure the strong-column weak-beam mechanism. In addition, a minimum joint transverse reinforcement ratio of 0.60% is recommended to insure that the failure will not occur in the joint zone.

Very limited research studies have been conducted to examine bond of glass fibre reinforced polymer (GFRP) bars with high concrete strength. The current research project aims to compare between bond measured from a pull-out test and a hinged beam test for GFRP bars embedded in high strength concrete. Different parameters influencing bond such as GFRP bar diameter, embedment length and surface configuration were investigated in both test methods, while the bar position, i.e. top or bottom, was only studied in hinged beams. Seventy-two pull-out cubes, eight pull-out prisms and twenty-four hinged beams reinforced with GFRP bars were constructed and tested to failure. Twelve pull-out cubes and four hinged beams reinforced with steel bars were also tested for comparison purposes. The results showed that bond stress – slip curves obtained from various testing methods were similar, consisting of high initial stiffness, followed by nonlinear ascending and softening branches. In addition, it was found that the experimental bond strength obtained from hinged beams was higher than both bond strengths measured by the pull-out cube and pull-out prism. However, when a finite element analysis was conducted for hinged beams, it was shown that the tensile force in the reinforcing bar estimated by equilibrium conditions is overestimated as the large deformation of hinged beams at failure was not considered. Therefore, if the tensile force obtained from the finite element analysis is used to calculate the bond strength, it would be similar to that obtained from pull-out cube and prism. Moreover, it was found that the distribution of tensile and bond stresses was nonlinear along the GFRP embedment length and bond stress at the vicinity of the free end increased with increasing the load due to redistribution of bond stresses along the embedment length. Bond strengths were compared against the prediction methods provided in ACI-440.1R, CSA-S806, CSA-S6 and JSCE 1997. In general, all design codes showed conservative results for all specimens tested and ACI predictions gave a good agreement with experimental data compared to other codes. Artificial neural network models were developed to predict bond strength of GFRP bars in concrete. These models used bar diameter, embedment length, concrete compressive strength and concrete cover as input variables. The developed ANN models showed to be able to predict bond strength of GFRP bars in concrete and, therefore, were used to conduct a parametric study. / Higher Education Institute, Government of Libya

The primary objective of this research was to examine the strength degradation of Glass Fiber Reinforced Polymer (GFRP) bars at high temperature and alkalinity and determine if an Arrhenius type relationship can be used as a means of projecting life. The work done includes a thorough literature review, experiments and development of strength prediction models. The experimental work involves exposure of GFRP bars incased in cement mortar to lime-water solution at 30, 45 and 57°C. Overall 100 specimens were included in the experimental program. The tensile strength and modulus of elasticity retention after 180 days of exposure at 57°C was 57% and 82% respectively. The secondary objective was to determine the moisture absorption properties of GFRP bars. The moisture absorption data available is till 80 days from the immersion of the specimens in the tank. The collected data was used in the development of strength retention models. Two strength prediction models, Time Shift Method and Fickian Model for moisture absorption are formulated. Using the Fickian Model, strength is predicted for GFRP bars, if used in bridge decks in Roanoke, Virginia. The strength loss predicted was 45% after 50 years of exposure in real life environment. A linear relationship was observed when the moisture content and strength retention were plotted. The study estimates a strength loss higher than the ACI-440H recommended environmental degradation factor of 0.7 to calculate the design ultimate tensile strength. / Master of Science

Continuous beams represent main structural elements in most reinforced concrete (RC) structures such as parking garages and overpass bridges. Deterioration of such structures due to corrosion of steel reinforcement is common in North America. To overcome the corrosion problems, the use of fiber-reinforced polymer (FRP) bars and stirrups becomes a viable alternative to steel reinforcement. However, to date, the shear behaviour of FRP-RC continuous beams has not been explored yet. As such, the objective of this study is to investigate the shear behaviour of such beams. In this study, twenty four full-scale continuous concrete beams were constructed and tested. The test beams had rectangular cross section with 200-mm width and a height of 300, 550 or 850 mm and were continuous over two equal spans. The main investigated parameters were concrete strength, type and ratio of longitudinal reinforcement, type and ratio of transverse reinforcement and beam effective depth. Moreover, a 3-D nonlinear finite element model (FEM) was constructed to simulate the behaviour of FRP-RC continuous beams. The model was verified against the experimental results and validated against test results from previous studies. Then, the verified/validated model was used to conduct a parametric study to investigate the effect of a wide range of the parameters on the shear behaviour of GFRP-RC beams. The experimental and FEM results showed that shear-critical GFRP-RC continuous beams exhibited moment redistribution. Also, it was observed that increasing the concrete strength and the longitudinal reinforcement ratio increased the shear strength significantly. Moreover, the presence of GFRP stirrups significantly enhanced the shear strength of the tested beams. Regarding the size effect, test results showed that there was adverse or no size effect on the shear strength of GFRP-RC continuous beams when they failed in the interior shear span while beams failed in the exterior shear span exhibited clear size effect. Furthermore, a comparison between the test results and the provisions of the available models and FRP standards and design guidelines in North America revealed that these design provisions can be safely applied to continuous beams. / February 2016

An investigation on the application of hybrid glass fibre reinforced polymer (GFRP) and steel bars bars as longitudinal reinforcement for simple and continuous concrete beams is presented. Three simply and eleven multi-spans continuous reinforced concrete beams were constructed and tested to failure. Nine continuous and two simply supported beams were reinforced with a hybrid combination of both GFRP and steel re-bars at mid spans and internal support regions. In addition, two continuous concrete beams reinforced with either GFRP or steel bars and one simply supported beam reinforced with GFRP bars were tested as control beams. The beams were classified into two groups according to the reinforcement configurations. All specimens tested were 200 mm in width and 300 mm in depth. The continuous beams comprised of two equal spans, each of 2600 mm, while the simply supported beams had a span of 2600 mm. Unlike GFRP reinforced concrete beams, the hybrid and steel reinforced concrete beams failed in a favourable ductile manner and demonstrated narrow cracks and smaller deflections compared to the GFRP-reinforced control beam. The lower stiffness and higher deflection of GFRP reinforced concrete beams can be controlled and improved by the use of steel reinforcement in combination with GFRP re-bars. However, the ratio of GFRP to steel reinforcement is a key factor to ensure sufficient ductility and stiffness beyond the first cracking stage. The experimental results showed that the extent of moment redistribution in hybrid reinforced continuous beams depends mainly on the amount of hybrid reinforcement ratio in critical sections. Similar area of steel and GFRP bars in critical sections leads to limited moment redistribution whereas different amount of steel and FRP bars in critical sections leads to a remarkable moment redistribution. Design guidelines and formulas have been validated against experimental results of hybrid GFRP/steel reinforced concrete beams tested. The Yoon’s equation reasonably predicted the deflections of the hybrid beams tested whereas Qu’s model which is based on ACI 440.1R-15 underestimated the deflections of hybrid beams tested at all stage of loading after cracking. The ACI 440.2R-08 and Pang et al., (2015) equations reasonably predicted the sagging failure moment in most continuous hybrid reinforced concrete beams, whereas they underestimated the hogging flexural strength at failure of most hybrid continuous beams. On the other hand, the formulas proposed by Yinghao et al., (2013) was very conservative in predicting the failure moment at the critical sagging and hogging sections. On the analytical side, a numerical technique consisting of sectional analyses has been developed to predict the moment–curvature relationship and moment capacity of hybrid FRP/ steel reinforced concrete members. The numerical technique has been validated against the experimental test results obtained from the current research and those reported in the literature. In addition, a two-dimensional nonlinear finite element model was proposed using ABAQUS package. The proposed model was validated against the experimental results of the beams tested in the present research. / Higher Education Institute in the Libyan Government

Yes / The flexural performance of geopolymer concrete (GPC) T-beams reinforced longitudinally with GFRP bars under a four-point static bending test was investigated. Six full-scale simply supported T-beams were cast and tested; one control specimen was made with ordinary Portland cement concrete (OPCC), while the other five beams were made of geopolymer concrete. The G-GPC2 was designed to attain the same theoretical moment capacity as the G-OPCC6 control beam. The main parameters investigated were the reinforcement ratio of ρ_f/ρ_b= 0.75, 1.05, 1.12, 1.34 and 1.34 for G-GPC1, G-GPC2, G-GPC3, G-GPC4, and G-GPC5, respectively, and compressive strength of geopolymer concrete. Based on the results of the experiments, the ultimate strain of GPC did not show the same behaviour as that of OPCC, which affects the mode of failure. The beam capacity and deflection were, respectively, overestimated and underestimated using the ACI 440 2R-17 predictive equations.

Yes / The results of testing two simply and three continuously supported concrete beams reinforced with glass fiber-reinforced polymer (GFRP) bars are presented. The amount of GFRP reinforcement was the main parameter investigated. Over and under GFRP reinforcements were applied for the simply supported concrete beams. Three different GFRP reinforcement combinations of over and under reinforcement ratios were used for the top and bottom layers of the continuous concrete beams tested. A concrete continuous beam reinforced with steel bars was also tested for comparison purposes. The experimental results revealed that over-reinforcing the bottom layer of either the simply or continuously supported GFRP beams is a key factor in controlling the width and propagation of cracks, enhancing the load capacity, and reducing the deflection of such beams. Comparisons between experimental results and those obtained from simplified methods proposed by the ACI 440 Committee show that ACI 440.1R-06 equations can reasonably predict the load capacity and deflection of the simply and continuously supported GFRP reinforced concrete beams tested.

O uso de novos materiais na construção civil combinado com a alta tecnologia dos processos construtivos pode conduzir à redução de custo e melhoria no comportamento da estrutura. Recentemente, em função da corrosão das barras de aço dentre outros fatores, muitos pesquisadores têm sugerido a utilização de barras não-metálicas como substituição das barras aço nas estruturas em concreto. Além das barras não-metálicas permitirem cobrimentos menores e possibilitarem menor custo de manutenção, outras vantagens no seu uso podem ser citadas, tais como: pequeno peso específico, alta resistência à tração, não condutibilidade elétrica, térmica e magnética, entre outras. Este trabalho analisa o comportamento da aderência entre barras de GFRP (barras de fibra de vidro impregnada por polímero) e o concreto, por meio de uma revisão bibliográfica e ensaios de arrancamento padronizados, segundo o RILEM-FIP-CEB (1973). Foram consideradas as influências dos parâmetros como a resistência à compressão do concreto e o diâmetro da barra de GFRP. Com base nos resultados experimentais, buscou-se comparar o comportamento de aderência barra de GFRP-concreto e barra de aço-concreto, além da verificação das formulações para previsão da resistência de aderência segundo códigos normativos e a literatura técnica, para estruturas armadas com barras de aço e barras de FRP. Posteriormente, realizou-se a análise numérica da aderência, por meio do método dos elementos finitos. Nos modelos experimentais de arrancamento pode-se perceber a influência das propriedades mecânicas e da conformação superficial das barras de GFRP no comportamento da aderência, apresentando menores resistências de aderência quando comparadas às barras de aço de diâmetro similar. O valor da resistência de aderência determinado experimentalmente foi maior que o valor proposto pelos códigos normativos. Os modelos numéricos não representaram satisfatoriamente o comportamento experimental, visto que se trata de uma simulação numérica linear e o comportamento experimental força x deslocamento é não-linear. / The use of new materials in civil construction combined with high technology processes leads to improvements in many aspects, like cost reductions and better structural behavior. Recently, due to corrosion of the steel bars, among other factors, many researchers have been suggesting the use of non-metallic bars as a substitution of the steel reinforcement in concrete structures. Besides, the non-metallic bars allow smaller clear cover and make possible lower maintenance cost, other advantages can be mentioned, such as: low specific weight, high tensile strength, electrical, thermal and magnetic non-conductivities, and others. This work analyzes the bond behavior between GFRP bars (Glass Fiber Reinforced Polymer bars) and concrete, through state-of-art and standard pull-out tests, according to RILEM-FIP-CEB (1973). The influence of some parameters, as compressive concrete strength and GFRP bar diameter, was considered. Based on the experimental results, it was aimed at comparing the bond behavior of the GFRP-concrete bar with the steel-concrete bar, in addition to the verification of bond strength formulations established by the standards codes and the bibliography for structures reinforced with steel bars and FRP bars. Further, the bond numerical analysis was carried out through finite elements. In the pull-out tests, the influence of mechanical properties and superficial conformation on the GFRP bars was observed in the bond behavior, presenting smaller bond strength than the steel bars of similar diameter. The value of the experimental bond strength was larger than the value proposed by standards codes. The numerical models did not represent well the experimental behavior given that a linear numerical simulation was considered, but, actually, the experimental load x slip behavior is non-linear.

With the rise in constructing using FRP reinforcement, owing to corrosion problems in steel-reinforced structures, there is a need for a system to resist lateral loads induced from wind and earthquake loads. The present study addressed the applicability of reinforced-concrete shear walls totally reinforced with glass-fiber-reinforced polymer (GFRP) bars to attain reasonable strength and drift requirements as specified in different codes. Four large-scale shear walls - one reinforced with steel bars (as reference specimen) and three totally reinforced with GFRP bars - were constructed and tested to failure under quasi-static reversed cyclic lateral loading. The GFRP-reinforced walls had different aspect ratios covering the range of medium-rise walls. The reported test results clearly showed that properly designed and detailed GFRPreinforced walls could reach their flexural capacities with no strength degradation, and that shear, sliding shear, and anchorage failures were not major problems and could be effectively controlled. The results also showed recoverable and self-centering behavior up to allowable drift limits before moderate damage occurred and achieved a maximum drift meeting the limitation of most building codes. Acceptable levels of energy dissipation accompanied by relatively small residual forces, compared to the steel-reinforced shear wall, were observed. Finite element simulation was conducted and the analyses captured the main features of behavior. Interaction of flexural and shear deformations of the tested shear walls was investigated. It was found that relying on the diagonal transducers tended to overestimate shear distortions by 30% to 50%. Correcting the results based on the use of vertical transducers was assessed and found to produce consistent results. Decoupling the flexural and shear deformations was discussed. Using GFRP bars as elastic material gave uniform distribution of shear strains along the shear region, resulting in shear deformation ranging from 15 to 20% of total deformation. The yielding of the steel bars intensified the shear strains at the yielding location, causing significant degradation in shear deformation ranging from 2 to 40% of total deformation. The results obtained demonstrated significantly high utilization levels of such shear wall type, therefore, primary guidelines for seismic design of GFRP-reinforced shear wall in moderate earthquakes regions was presented, as no design guidelines for lateral load resistance for GFRP-reinforced walls are available in codes. The ultimate limit state was addressed by providing strength capacity that limit ductility demand to their safe flexural displacement capacity. The strength demands were derived from ground motion spectra using modification factors that depend on both the strength and energy absorption of the structure. Deformation capacity was derived by proposing new definitions for elastic (virtual yield) displacement and maximum allowable displacement. Strength modification factor was proposed based on the test results. The occurrence of "virtual plastic hinge" for GFRP-reinforced shear walls was described providing new definitions convenient with the behavior of the GFRP-reinforced shear walls. "Virtual plastic hinge" length was estimated based on observations and calculations. Subsequently, the experimental results were used to justify the proposed design procedure. The promising results could provide impetus for constructing shear walls reinforced with GFRP bars and constitute a step toward using GFRP reinforcement in such lateral-resisting systems.