Socioeconomic study is a procedure that ensures that the likely positive and negative impact of a new project on the socioeconomic life of a community is taken into account. It has become a crucial part of sustainable development process. The understanding of socioeconomic study procedures is an increasing necessity for all those involved in the process. Similarly, proper knowledge of the function of socioeconomic study during the environmental impact assessment (EIA) process is of paramount importance for the mitigation of the likely effects of the new development. Furthermore, as the world is gradually growing into a global village, it has become increasingly imperative that organizations integrate the people in their operations' areas in the overall objective of their businesses. Community engagement (CE) is a partnership process that can be used to assess and manage the problem affecting the well-being of a community because of a new development. This research work used the SWOT matrix technique to develop a management framework that companies can use to manage their weaknesses and threats because of inadequate community engagement strategy. To achieve this, the work evaluated the extent to which socioeconomic study is integrated into the EIA processes. It also assessed the extent to which oil companies are using community engagement as a development strategy. The findings of this dissertation revealed that oil explorations in the Niger Delta area have affected the well-being of the people both positively and negatively. Unfortunately, their negative impact outweighed their positive impact. Although they carry out socioeconomic studies, they have been neglecting the recommendations reported in the socioeconomic study document by experts. The level of community engagements therefore has also been very poor. SWOT matrix technique was used to develop the management framework for each company based on the perceived strengths, weaknesses, opportunities and threats of the companies as revealed in this research. This should serve as a guide for the companies in their CE strategies. / Thesis (M.Ing. (Development and Management Engineering))--North-West University, Potchefstroom Campus, 2009.

This paper will discuss the conversion of gas produced from biomass into liquid fuel through the combination of naturally occurring processes, which occur in landfills and anaerobic digesters, and a gas-to-liquids (GTL) facility. Landfills and anaerobic digesters produce gases (LFG) that can be converted into syngas via a Tri-reforming process and then synthesized into man-made hydrocarbon mixtures using Fischer-Tropsch synthesis. Further processing allows for the separation into liquid hydrocarbon fuels such as diesel and gasoline, as well as other middle distillate fuels. Conversion of landfill gas into liquid fuels increases their energy density, ease of storage, and open market potential as a common “drop in” fuel. These steps not only allow for profitable avenues for landfill operators but potential methods to decrease greenhouse gas emissions. The objective of this paper is to present a preliminary design of an innovative facility which processes contaminated biogases and produces a valuable product. An economic analysis is performed to show feasibility for a facility under base case scenario. A sensitivity analysis is performed to show the effect of different cost scenarios on the breakeven price of fuel produced. Market scenarios are also presented in order to further analyze situations where certain product portions cannot be sold or facility downtime is increased. This facility is then compared to traditional mitigation options, such as flaring and electricity generation, to assess the effect each option has on cost, energy efficiency, and emissions reduction.

Trace component analysis in gasification processes are important part of elemental component balances in order to understand the fate of these participating compounds in the feedstock. Residual traces in the raw synthesis gas after quench could bring about the poisoning of catalysts and corrosion effects on plant facilities. The objective of this work is to investigate the effects of quenching operation on the trace components during test campaigns of the autothermal non-catalytic reforming of natural gas (Gas-POX) mode in the HP POX (high pressure partial oxidation) test plant. In order to achieve this, Aspen Plus simulation model of the quench chamber of the HP POX test plant was developed to re-calculate the quench chamber input amount of different trace compounds from their output amount measured during test points of the Gas-POX campaigns. Variation in quench water temperatures from 130 °C to 220 °C and pH value of quench water as well as the resulting variation in Henry´s and Dissociation constant of the traces (CO2, H2S, NH3 and HCN) changed the distribution of traces calculated in the quench water. The formation of traces of organic acid (formic acid and acetic acid) and traces of BTEX, PAHs and soot in the quench water effluent were discussed. The discrepancies between equilibrium constant and reaction quotient (non-equilibrium or real) for the formation of NH3 and HCN at the exit of the gasifier were discussed. The assessment of the results in this work should lead to the improvement in the understanding of trace components and concepts that could be employed to influence their formation and reduction.

Trace component analysis in gasification processes are important part of elemental component balances in order to understand the fate of these participating compounds in the feedstock. Residual traces in the raw synthesis gas after quench could bring about the poisoning of catalysts and corrosion effects on plant facilities. The objective of this work is to investigate the effects of quenching operation on the trace components during test campaigns of the autothermal non-catalytic reforming of natural gas (Gas-POX) mode in the HP POX (high pressure partial oxidation) test plant. In order to achieve this, Aspen Plus simulation model of the quench chamber of the HP POX test plant was developed to re-calculate the quench chamber input amount of different trace compounds from their output amount measured during test points of the Gas-POX campaigns. Variation in quench water temperatures from 130 °C to 220 °C and pH value of quench water as well as the resulting variation in Henry´s and Dissociation constant of the traces (CO2, H2S, NH3 and HCN) changed the distribution of traces calculated in the quench water. The formation of traces of organic acid (formic acid and acetic acid) and traces of BTEX, PAHs and soot in the quench water effluent were discussed. The discrepancies between equilibrium constant and reaction quotient (non-equilibrium or real) for the formation of NH3 and HCN at the exit of the gasifier were discussed. The assessment of the results in this work should lead to the improvement in the understanding of trace components and concepts that could be employed to influence their formation and reduction.:List of Figures vii List of Tables xii List of Abbreviations and Symbols xiii 1 Introduction 1 1.1 Background 1 1.2 Objective of the Work 4 1.3 Overview of the Work 5 2 Process and test conditions 6 2.1 HP POX test plant 6 2.2 Test campaign procedure 8 2.2.1 Gas-POX operating parameter range 8 2.2.2 Gas-POX experiments 9 2.2.3 Net reactions of partial oxidation 9 2.3 Gaseous feedstock characterization 11 2.3.1 Natural gas feedstock composition 11 2.4 Analytical methods for gaseous products 12 2.4.1 Hot gas sampling 12 2.4.2 Raw synthesis gas analysis after quench 13 2.5 Aqueous phase product analysis 14 2.5.1 Molecularly dissolved trace compounds and their ions trace analysis 14 2.5.2 Other trace analysis 15 2.6 Limit of accuracy in measurement systems 15 2.7 Summary 17 3 Simulation and methods 18 3.1 Test points calculation of the HP POX test campaign 18 3.1.1 Aspen Plus model for HP POX quench water system 19 3.2 Gas-POX 201 VP1 quench water system model simulation by Aspen Plus 23 3.2.1 Measured and calculated input parameters 23 3.2.2 Calculated sensitivity studies of species and their distribution for test point (VP1) 24 3.3 Used calculation tools related to the work 25 3.3.1 VBA in Excel 25 3.3.2 Python as interface between Aspen Plus and Microsoft Excel 26 3.3.3 Aspen Simulation Workbook 27 3.4 Summary 29 4 Trace components in quench water system 30 4.1 Physico-chemical parameters of quench water 31 4.1.1 Quench water pH adjustment 32 4.1.2 Henry constant 34 4.1.3 Dissociation constant 35 4.1.4 Organic acids in quench water 38 4.2 Carbon dioxide (CO2) 39 4.2.1 Results of sensitivity study: quench water temperature variation effects on CO2 41 4.2.2 Results of sensitivity study: quench water pH variation influence on CO2 42 4.3 Nitrogen compounds 43 4.3.1 Ammonia (NH3) 44 4.3.2 Results of sensitivity study: quench water temperature variation effects on NH3 46 4.3.3 Results of sensitivity study: quench water pH variation influence on NH3 47 4.3.4 Hydrogen Cyanide (HCN) 48 4.3.5 Results of sensitivity study: quench water temperature variation effects on HCN 50 4.3.6 Results of sensitivity study: quench water pH variation influence on HCN 50 4.4 Sulphur compounds: H2S 51 4.4.1 Results of sensitivity study: quench water temperature variation effects on H2S 53 4.4.2 Results of sensitivity study: quench water pH variation influence on H2S 54 4.5 Summary 55 5 Organic acids trace studies in quench water 57 5.1 Organic acids interaction with ammonia compounds in the quench water 57 5.2 Formic acid 62 5.2.1 Trace of formic acid in quench water 64 5.3 Acetic acid 67 5.3.1 Trace of acetic acid in quench water 69 5.4 Summary 72 6 Temperature approach studies for NH3 and HCN formation in gasifier 74 6.1 Nitrogen compounds: NH3 and HCN 74 6.2 Ammonia (NH3) formation in the gasifer 77 6.3 Hydrogen cyanide (HCN) formation in the gasifier 79 6.4 Discrepancies between back-calculated reaction quotients and equilibrium constants of the NH3 formation 81 6.4.1 Case 1: calculated equilibrium distribution between N2, NH3 and HCN 81 6.4.2 Case 2: calculated equilibrium distribution between NH3 and HCN 83 6.5 Summary 84 7 Traces of BTEX, PAHs and soot in quench water 86 7.1 Quench water behaviour 87 7.2 BTEX compounds 88 7.2.1 BTEX in quench water effluent 90 7.3 PAH compounds 93 7.3.1 PAHs in quench water effluent 95 7.4 Soot formation 99 7.4.1 Soots in quench water effluent 101 7.5 Summary 102 8 Summary and outlook 103 Bibliography 106 9 Appendix 135 List of Figures Figure 2.1: HP POX test plant main facility components and material flow courtesy of [Lurgi GmbH, 2008] 6 Figure 2.2: Simplified scheme of HP POX plant (including quench system) [Lurgi GmbH, 2008] 7 Figure 2.3: Overview of reactions of methane 10 Figure 3.1: Simplified scheme for HP POX quench water system 18 Figure 3.2: Aspen Plus flow diagrams of simulated HP POX quench water system 19 Figure 3.3: Integration of information and functions in VBA via Microsoft Excel to Aspen Plus model 25 Figure 3.4: Integration of information and functions in Python via Microsoft Excel to Aspen Plus model 26 Figure 3.5: ASW enables Excel users to rapidly run scenarios using the underlying rigorous models to analyze plant data, monitor performance, and make better decisions. 27 Figure 4.1: Vapour-liquid equilibria system of CO2, H2S, NH3, HCN and organic acids in the quench water and extended mechanisms according to [Kamps et al., 2001], [Alvaro et al., 2000], [Kuranov et al., 1996], [Xia et al., 1999] and [Edwards et al., 1978]. 30 Figure 4.2: HP POX quench water system with pH regulator for sensitivity studies 34 Figure 4.3: Henry´s constant for CO2, H2S, NH3 and HCN derived from [Edwards et al., 1978] for CO2, [Alvaro et al., 2000] for NH3, [Kamps et al., 2001] for H2S, and [Rumpf et al., 1992] for HCN 35 Figure 4.4: Dissociation constants for CO2, H2S, NH3, HCN and H2O derived from [Alvaro et al., 2000], [Kamps et al., 2001], and [Edwards et al., 1978] 37 Figure 4.5: The flow of CO2 in the quench water cycle (test point VP1). 40 Figure 4.6: Calculated quench water temperature variation and effects on CO2 distribution 42 Figure 4.7: Calculated influence of pH regulation and effects on CO2 distribution 43 Figure 4.8: The flow of NH3 in the quench water cycle (test point VP1). 46 Figure 4.9: Calculated quench water temperature variation and effects on NH3 distribution 47 Figure 4.10: Calculated influence of pH regulation and effects on NH3 distribution 48 Figure 4.11: The flow of HCN in the quench water cycle (test point VP1). 49 Figure 4.12: Calculated quench water temperature variation and effects on HCN distribution 50 Figure 4.13: Calculated influence of pH regulation and effects on HCN distribution 51 Figure 4.14: The flow of H2S in the quench water cycle (test point VP1) 53 Figure 4.15: Calculated quench water temperature variation and effects on H2S distribution 54 Figure 4.16: Calculated influence of pH regulation and effects on H2S distribution 55 Figure 5.1: Aspen Plus back-calculated (real) formic acid concentration, quench water temperature and the calculated equilibrium formic acid concentration against back-calculated (real) ammonia concentration for the 47 test points (using amongst others sampled HCOO- and NH4+ values according to Table 2.6). 59 Figure 5.2: Aspen plus back-calculated (real) formic acid concentration, back-calculated (real) ammonia concentration and the calculated equilibrium formic acid concentration against quench water temperature for the 47 test points (using amongst others sampled HCOO- and NH4+ values according to Table 2.6). 60 Figure 5.3: Aspen plus back-calculated (real) acetic acid concentration, quench water temperature and the calculated equilibrium acetic acid concentration against back-calculated (real) ammonia concentration for the 47 test points. 61 Figure 5.4: Aspen plus back-calculated (real) acetic acid concentration, back-calculated (real) ammonia concentration and the calculated equilibrium acetic acid concentration against quench water temperature for the 47 test points. 62 Figure 5.5: Concentration of formic acid (Aspen plus calculated m_eq and back-calculted m_real) formation in the quench and quench water temperature for the 47 test points. 64 Figure 5.6: Concentration of formic acid (Aspen plus calculated m_eq and back-calculted m_real) in the quench against quench water temperature for the 47 test points (as in Fig.5.2). 65 Figure 5.7: Comparison between formic acid equilibrium constant (Keq), reaction quotient (Kreal) and the quench water temperature for the 47 test points. 66 Figure 5.8: Comparison between formic acid equilibrium constant (Keq) and reaction quotient (Kreal) against quench water temperatures for the 47 test points. 67 Figure 5.9: Concentration of acetic acid (Aspen plus calculated m_eq and back-calculted m_real) in the quench and quench water temperature for the 47 test points. 69 Figure 5.10: Concentration of acetic acid (Aspen plus calculated m_eq and back-calculted m_real) in the quench against quench water temperature for the 47 test points (as in Fig.5.4). 70 Figure 5.11: Comparison between acetic acid equilibrium constant (Keq), reaction quotient (Kreal) and the quench water temperature for the 47 test points. 71 Figure 5.12: Comparison between acetic acid equilibrium constant (Keq) and reaction quotient (Kreal) against quench water temperatures for the 47 test points. 72 Figure 6.1: Mole fraction of gas compoents in the hot gas outlet out of gasifier against hot gas temperature for the 47 test points 76 Figure 6.2: Calculated reaction quotient (Q) and equlibrium constant (Keq) for NH3 against hot gas temperature for the 47 test points (see Fig. 9.10 in Appendix) 77 Figure 6.3: NH3 temperature approach against hot gas temperature for the 47 test points (see Fig. 9.11 in Appendix) 78 Figure 6.4: Calculated reaction quotient (Q) and equlibrium constant (Keq) for HCN against hot gas temperature for the 47 test points (see Fig. 9.13 in Appendix) 79 Figure 6.5: HCN temperature approach against hot gas temperature for the 47 test points (see Fig. 9.14 in Appendix) 80 Figure 6.6: Comparison between calculated real and equilibrium hot gas N2, NH3 and HCN mol fractions against their respective hot gas temperature (case 1). 82 Figure 6.7: Relations between back-calculated real and equilibrium hot gas N2, NH3 and HCN mol fractions (for chemical equilibrium according to equations (6.1) and (6.4)) against their respective hot gas temperature (see Case 1, Section 6.4.1, and Fig. 6.6) 82 Figure 6.8: Comparison between calculated real and equilibrium hot gas HCN mol fraction against their respective hot gas temperature (case 2). 83 Figure 6.9: Relations between back-calculated real and equilibrium hot gas HCN mol fractions, and change in NH3 mol fractions (for chemical equilibrium according to equation (6.4)), against their respective hot gas temperature (see. Case 2, Section 6.4.2 and Fig. 6.7) 84 Figure 6.10 Comparison between NH3 and HCN formation (mole fraction) calculated equilibrium constant (Keq) and calculated reaction quotient (Q), N2 consumption and hot gas temperatures for the 47 test points (case 1 and case 2). 85 Figure 7.1: HP POX test plant quench water system 88 Figure 7.2: Traces of BTEX measured in the Gas-POX 203 – 207 quench water effluent sample. 91 Figure 7.3: Individual component of BTEX measured in the Gas-POX 203 – 207 quench water effluent sample. 92 Figure 7.4: (a) Alkyl radical decomposition and (b) C1 and C2 hydrocarbons oxidation mechanism [Warnatz et al., 2000] 93 Figure 7.5: Recombination of C3H3 to form benzene 94 Figure 7.6: The Diels - Alder reaction for the formation of PAHs 95 Figure 7.7: Amount of PAHs that were detected in Gas-POX 203 – 207 test points quench water effluent samples. 97 Figure 7.8: Distribution of PAH compounds in Gas-POX 203 – 207 quench water effluent samples. 98 Figure 7.9: Some steps in soot formation [McEnally et al., 2006]. 99 Figure 7.10: Illustration of soot formation path in homogenous mixture [Bockhorn et al., 1994] 100 Figure 9.1: Aspen flow sheet set up for HP POX quench system GasPOX 201 VP1 (simplified and extension of Fig. 3.2, organic acids not taken into account). Tabulated values are given in Table 9.11. 135 Figure 9.2: Comparison between the Henry´s constant profiles: Aspen Plus (markers) and Literatures (solid lines) ([Edwards et al., 1978] for CO2, [Alvaro et al., 2000] for NH3, [Kamps et al., 2001] for H2S, and [Rumpf et al., 1992] for HCN as it can be seen in Fig. 4.3) 137 Figure 9.3: Henry´s constant profiles derived from literatures ([Edwards et al., 1978] for CO2, [Alvaro Pérez-Salado et al., 2000] for NH3, [Kamps et al., 2001] for H2S, and [Rumpf et al., 1992] for HCN as it can be seen in Fig. 4.3) 137 Figure 9.4: Comparison between the dissociation constant profiles: Aspen Plus (markers) and Literatures (solid or dashed lines) [Alvaro et al., 2000], [Kamps et al., 2001], and [Edwards et al., 1978] as in Fig.4.4. 138 Figure 9.5: Dissociation constant profiles derived from literatures [Kamps et al., 2001], and [Edwards et al., 1978] as in Fig.4.4. 138 Figure 9.6: Calculated pH values, temperature range and species 139 Figure 9.7: Aspen Plus flow sheet setup for organic acid compounds calculations (GasPOX 201 VP1, see also Table 9.12) 142 Figure 9.8: Aspen Plus flow sheet setup for nitrogen compounds calculations (GasPOX 201 VP1, see also Table 9.12, organic acids are taken into account in the aqueous streams of the quench system) 145 Figure 9.9: Yield of ammonia in gasifier (calculated real) and hot gas temperature against the 47 test points 146 Figure 9.10: Kreal or reaction quotient for ammonia formation in the gasifier against the 47 test points. 146 Figure 9.11: Temperature approach studies for ammonia and the 47 test points 147 Figure 9.12: Yield of HCN from the gasifier (calculated real and equilibrium) and hot gas temperature and the 47 test points 147 Figure 9.13: Comparison between equilibrium constant and reaction quotient for HCN and 47 test points 148 Figure 9.14: Temperature approach studies for HCN and the 47 test points 148 Figure 9.15: Comparison among equilibrium constants of reactions against temperature, T [°C] 149 Figure 9.16: Comparison among equilibrium constants of reactions against temperature, 1/T [1/K] 150 List of Tables Table 2.1: Outline of Gas-POX mode operating parameter range 8 Table 2.2: Outline of test runs operating mode and parameters of chosen test campaigns 9 Table 2.3: Natural gas feedstock compositions 12 Table 2.4: Product synthesis gas analysis method (hot gas before quench) [Brüggemann, 2010] 12 Table 2.5: Analysis methods for raw synthesis gas [Brüggemann, 2010] 13 Table 2.6: Analysis methods for aqueous phase products [Brüggemann, 2010] 14 Table 2.7: Relative accuracy for the measured value for temperature, pressure and flow of each feed and product stream [Meyer, 2007] and [Brüggemann, 2010] 17 Table 3.1: Description of blocks used in Aspen Plus simulation. 20 Table 3.2: HP POX test plant quench water cycle parameters Gas-POX 201 VP1* 23 Table 3.3: pH regulator parameters 24 Table 4.1: Organic acids distribution in streams for VP1 based on calculation from Aspen Plus. 38 Table 4.2: The distribution of CO2 and its ions in all the streams 40 Table 4.3: The distribution of NH3 and its ions in all the streams 45 Table 4.4: The distribution of HCN and its ions in all the streams 49 Table 4.5: The distribution of H2S and its ions in all the streams 52 Table 7.1: Relative sooting tendency [Tesner et al., 2010] 101 Table 9.1: Natural gas feed analysis method [Brüggemann, 2010] 135 Table 9.2: pH scale with examples of solution [NALCO 2008] 136 Table 9.3: Gas-POX test campaigns and with designated serial numbers 140 Table 9.4: Summary of correlation coefficient (r) from Figures in Chapter 5 144 Table 9.5: Comparison among reactions temperatures and heat of reactions 149 Table 9.6: Content of BTEX compounds in Gas-POX quench water samples 151 Table 9.7: BTEX in quench water effluent samples results 152 Table 9.8: Content of PAH compounds in Gas-POX quench water samples 157 Table 9.9: PAHs in quench water effluent samples results 160 Table 9.10: Soot in quench water effluent samples results 169 Table 9.11: Aspen Plus flow sheet setup stream details (GasPOX 201 VP1, according to Fig.3.2 and Fig.9.1, organic acids not taken into account) 170 Table 9.12: Aspen Plus flow sheet setup for organic acid and nitrogen compounds calculations for GasPOX 201 VP1 (according to Figures 9.7 and 9.8, organic acids are taken into account) 174