Spectroscopic investigations have been carried out on an argon inductively coupled plasma operating at non-atmospheric pressure. The relationship between torch pressure and a number of plasma operating characteristics was explored for torch pressures between 100 and 3000 torr. The plasma operating characteristics examined include observed analyte emission intensities, electron densities, ion to atom ratios, and the deviation of plasma conditions from local thermodynamic equilibrium. The effect of pressure on the observed analyte emission intensities was found to include factors in addition to the change in density of species within the torch. Emission lines originating from ions and atoms with high ionization potentials (greater than 7 eV) increased in intensity with increasing torch pressure, in excess of that predicted by the increase in density of species present. Conversely, emission lines originating from atoms of low ionization potential decreased in intensity with increasing torch pressure despite the increase in density. The results of the spatial determination of electron densities and ion to atom ratios indicate that excitation conditions within the central channel of the plasma are shifted towards conditions of local thermodynamic equilibrium as the pressure within the torch is increased. In addition, it is possible to obtain improved limits of detection by optimizing the torch pressure for the analyte element of interest.

A comprehensive investigation was reported into the synthesis, characterization and photoluminescence properties of calcium metaniobates and associated alkali earth alloy systems. Previous studies have shown that calcium metaniobate exhibits a strong self-activated blue luminescence at room temperature in stark contrast to the pyroniobates which are known to exhibit a temperature dependent luminescence that quenches above 100 K. The mechanism of this behavior has been studied by measuring the spectral characteristics of the photoluminescence and photoluminescence excitation spectra on the crystalline and morphological properties of the powders as determined from x-ray diffraction and scanning electron microscopy. By correlating the synthesis parameters with the physical, chemical and optical properties of calcium metaniobate, the optimum conditions for efficient blue-visible emission and chemical stability under vacuum ultraviolate (VUV) radiation has been determined. These materials have the potential to replace Barium Magnesium Aluminate, which is currently used as the blue phosphor in plasma displays.

Recently, the high radiance of synchrotron sources was used to enhance FTIR spectrometer performance. However, excessive channel spectra when synchrotron sources are used degrade the quality of retrieved spectral parameters. In the research reported in this thesis, seven different techniques for handling channel spectra were investigated. These techniques were used to reduce channel spectra for a test group of seven samples of CO2 mixed with air recorded using the synchrotron source at the Canadian Light Source. The increases in signal to noise ratio (SNR) of spectra handled with each technique were calculated. SNR results showed that transmission spectra, produced using synthetic background spectra with simulated channel spectra, achieved the highest SNR improvement. However, when the spectra groups were fitted using nonlinear least square fit algorithm, the technique using channel spectra fitting produced the smallest fitting residual. Moreover, the retrieved intensities and air broadening coefficients of 21 spectral lines showed that the spectral fitting technique produced the most accurate values as compared to the HITRAN 2008 database. Although the spectral fitting technique was accurate in retrieving spectral line parameters, applying the technique at wider spectral ranges was less accurate. A modification to the channel spectra fitting technique by performing iterations of channel fitting was introduced to process wider spectral ranges. Carbon dioxide laser band I centred at 961 wavenumber was analyzed using 24 spectra recorded under different experimental conditions. The intensity and air-and self-broadening coefficients were retrieved for 48 spectral lines with average deviations from HITRAN database values of 2.11%, 1.25% and 4.14%, respectively, using the Voigt profile. These average deviations lie within the uncertainty limits listed by the database. The deviation between our results and other results reported in the literature were also examined and it is found to be also within the range of HITRAN uncertainties. The effect of errors in fitting channel spectra parameters was examined and found to be mitigated by the inclusion of channel-free spectra in the multispectral fit. / xiv, 134 leaves : ill. ; 29 cm

Indiana University-Purdue University Indianapolis (IUPUI) / The purpose of this thesis is to use experimental methods to seek deeper understanding and better performance in the self-circulating self-regulating microfluidic gas generator initially developed in Dr. Zhu’s group, by changing the major features and dimensions in the reaction channel of the device. In order to effectively conduct experiments described above, a microfabrication method that is capable of making new microfluidic devices with low cost, short time period, as well as relatively high accuracy was needed first. Developing such a fabrication method is the major part of this thesis. We initially used patterned polymer films and glass slide, and bonded them together by sequentially aligning and stacking them into a microfluidic device with patterned double-sided tapes. Later we developed a more advanced microfabrication method that used only patterned polystyrene (PS) films. The patterned PS films were obtained from a digital cutter and they were bonded into a microfluidic device by thermopress bonding method that required no heterogeneous bonding agents. This new method did not need manual assembly which greatly improved its precision (~ 100 µm), and it used only PS as device material that has favorable surface wetting property for microfluidics applications. In order to find the optimized microfluidic channel design to improve gas generating performance, we've designed and fabricated microfluidic devices with different channel dimensions using the PS fabrication method. Based on the gas generation testing results of those devices, we were able to come up with the optimal dimensions for the reaction channel that had the best gas generation performance. To obtain a more fundamental understanding about the working mechanism of our device and its bubble dynamics, we have conducted ultrafast X-ray imaging test at Advanced Photon Source (APS), Argonne National Laboratory. High speed (100 KHz) phase contrast images were captured that allowed us to observe directly inside the reaction channel on the cross section view during the self-circulating catalytic reaction. The images provided us with lots of insightful information that in turn helped the dimensional improvement for the microchannel design. The 100 KHz high speed images also gave us useful information about the dynamics of bubble development on a catalyst bed, such as growth and merging of the bubbles.