<p>Welded built-up structural steel members are widely used as columns, beams, and beam-columns in various buildings, bridges, industrial complexes, etc. Modern cutting techniques are used in the fabrication of such members. Besides traditional saw cutting and oxy-flame cutting, the modern cutting techniques include plasma cutting, laser cutting, water- jet cutting, etc. The different cutting techniques induce different degrees of Heat Affected Zones (HAZ), which subsequently creates different degrees of geometrical and mechanical imperfections (residual stresses). Therefore, it could be expected that the true behavior of structural steel columns manufactured by such cutting techniques be different.</p><p>The main objective of this investigation was to study the characteristics and behavior of plasma cut-welded H-shaped steel columns at different slenderness ratios. However, this investigation also considered similar flame cut-welded H-shaped steel columns for comparison purposes. The H-shaped column sections were fabricated from plates having specified yield strength of 350MPa. First, the initial plate was cut into plate strips and then the plate strips (flanges and web) were welded together to form the H-shaped section in this investigation. The strength of these columns were established under uni-axial compressive loading with pinned end condition, allowing for minor axis rotation. Moreover, the structural imperfections such as residual stresses and geometrical imperfections were established. The residual stresses distributions were established at various stages of fabrication processes using the "method of section" technique. That is, the residual stresses in initial plate, plate strips (cutting effects), and column sections (cutting and welding effects) were established. Similarly, the geometrical imperfections were established at various stages of fabrication processes in this investigation.The temperature profiles were measured during the cutting and welding processes. As part of the scientific documentation, the mechanical characteristic of virgin steel plates were obtained by standard coupon tensile test.</p><p>Based on the experimental results on column strength, the general behavior of plasma cut columns and flame cut columns were similar. However, it was found that the plasma cut-welded steel columns seemed to carry higher loads than that of flame cut-welded columns for higher slenderness ratios( λ≥1). For lower slenderness ratios (0.5<λ<1), it was found that the flame cut-welded columns had higher strength than plasma cut-welded columns in this investigation. The residual stress distribution of both plasma cut column section and flame cut column section had the same general distribution. However, in general, the flame cut columns had high intensity of tensile residual stresses at their flange tips than the plasma cut columns. Moreover, the out-of-plane imperfections of column sections were within the code limitations. However, it was found that the flame cut-welded H-shaped steel columns seemed to have higher out-of-plane imperfections than the similar plasma cut-welded H-shaped steel columns in this investigation.</p> / Thesis / Master of Applied Science (MASc)

Globally the amount of electricity produced each year is increasing significantly. Between 1980 and 2010 the average increase was 407 billion kWh per year. To be able to meet this increasing electricity demand, without burdening the environment in a too large extent, the research and development of renewable energy production techniques is of great importance. In the light of this we wanted to dedicate our master thesis to help SubseaTechnology Scandinavia AB with the development of a vertical axis tidal current turbine. The project set out to do the initial design proposal of a 2 x 4 meter H-shaped Darrieus turbine by applying the Double Multiple Streamtube model. The optimization process was performed with the aid of MATLAB for four different foils. The study included two symmetrical foils; NACA 0012 and S-1046 together with two asymmetrical foils; S-1210 and E216. The parameters studied were the number of blades, chord length, tip speed ratio, fixed pitch and the operational range. In the project, effects such as blade to wake interaction, torque fluctuations etc. were also considered. From the simulations the two bladed turbine fitted with the S-1046 hydrofoil showed the highest performance but was struggling with an unfavorable oscillating torque. In the light of this the three bladed turbine fitted with the S-1046 hydrofoil with a chord of 0.13 m and an optimal tip speed ratio of 3.2 was determined. From the simulations the power coefficient reached 53.47 % for this case. This configuration also showed good performance in a relatively wide range of both tip speed ratios and free stream velocities. The model does not include several effects causing losses and the power coefficients calculated in this model are to be used as a comparison between the different turbine configurations and not as absolute values of performance. The simulations showed good potential for the use of asymmetrical foils in vertical axis turbines. The performance was evaluated for the upstream half of the turbine where the E216 foil exceeded the symmetrical foils in the range of ten percentage points.

This thesis includes the design, production and measurement of a wideband dualpolarized X-band aperture-coupled microstrip patch antenna. The wideband and dual-polarized operation is achieved through the use of H-shaped coupling slots. Therefore, the equivalent circuit modeling of a microstrip line fed H-shaped slot is also studied in this thesis. A step-by-step procedure is followed during the design process of the dual-polarized aperture-coupled microstrip antenna. First, an aperture-coupled microstrip antenna with a single rectangular slot, that exhibits a wideband characteristic for single polarization, is designed. Then, the design procedure is repeated for an antenna with H-shaped slot in order to satisfy the same specifications with a shorter slot. Finally, dual-polarized aperture-coupled microstrip antenna is designed. At this configuration, two H-shaped slots are used and they are placed orthogonal to each other. During the design process, the effects of antenna parameters on the input impedance characteristics of the antenna are investigated. These parametric analyses are done in CST Microwave Studio&reg / . The v designed dual-polarized wideband aperture-coupled microstrip antenna is manufactured. Simulation results and measurement results are compared. During the equivalent circuit modeling of an H-shaped slot fed by a microstrip line, an approach based on the reciprocity theorem is utilized. The method was originally proposed for rectangular shaped slots, in this thesis it is generalized for arbitrarily shaped slots. Software codes are developed in MATLAB to calculate the equivalent impedance of the slot.

Technologies such as direct broad cast satellite system (DBSS), Geosynchronous Earth Orbit (GEO) and Low Earth Orbit (LEO) satellite communications , global positioning system (GPS), high accuracy airborne navigation system and a large variety of radar systems demand for high level of antenna performance. Similar is the requirement for upcoming land based wireless systems such as cellular and indoor communication systems that is needed some more specific and additional features added to the antenna to compensate for the deficiencies encountered in system's performance. Though metallic antennas are capable enough to fulfil all the operational requirements, however at very high frequencies and under hostile temperature conditions they are constrained to face certain limitations. To avoid these constraints the performance of Dielectric Resonator Antennas (DRAs) is evaluated and their new applications are proposed. In the thesis, two types of antenna applications are sought :-First is for tracking and satellite applications that needs a larger aperture coverage in elevation plane. This coverage is realized with a good CP purity by proposing two ports dual linearly polarized DRA working at X-band. The DRA is excited by two orthogonal H-shaped aperture slots yielding two orthogonal polarizations in the broadside direction. A common impedance bandwidth of 5.9% and input port isolation of -35 dB are obtained. The broadside radiation patterns are found to be highly symmetric and stable with cross polarization levels -15dB or better over the entire matching frequency band. The maximum measured gain is found to be 2.5dBi at 8.4 GHz.- The 2nd type of antenna is a dual pattern diversity antenna to be used in the Body Area Network (BAN) context. This antenna combines a slot loop and DRA yielding broadside and end-fire radiation patterns respectively. Based upon the feeding techniques, the DG antenna is further divided into two categories one with planar feeds and the other with non-planar feeds (slot loop excited by planar CPW but DRA excited by vertical monopole) .Both types are successfully designed and measured upon body when configured into different propagation scenarios. The non-planar feeds antenna allows wider common impedance bandwidths than the planar feeds (4.95% vs 1.5%).In both cases, a maximum value of DG=9.5dB was achieved when diversity performance tests were carried out in rich fading environments. This value is close to the one (10 dB) theoretically reached in a pure Rayleigh environment and was obtained with efficiencies of 70% and 85% for the slot loop and the DRA respectively. Therefore, we conclude that these antennas could be used on the shoulders or the chest of professional clothes (firemen, policemen, soldier) where full planar integration is not a key issue but where the communication must be efficient in harsh environments and for various gestures, positions and scenarios

No description available.

Dans cette thèse, on vise deux types d'applications de l’antenne à résonateur diélectrique (DRA): 1) La réalisation d’un élément rayonnant pour un réseau phasé embarqué sur un véhicule terrestre ou un avion. Cet élément de base requiert une couverture en élévation supérieure à celle des éléments imprimés pour permettre une poursuite typique comprise entre ±70°. La couverture dans un cône large est assurée avec une bonne pureté de polarisation circulaire en alimentant l’antenne à travers deux ouvertures à fente en H orthogonales parfaitement découplées en bande X. 2) La deuxième structure est destinée à la diversité d’antennes dans le contexte des réseaux corporels embarqués ou Body Area Network (BAN). L’antenne à diversité combine une antenne fente en boucle avec un DRA ce qui permet dans un espace compact de réaliser des diagrammes de type “broadside” et “endfire” respectivement. Les alimentations considérées sont de 2 types; Soit purement planaire (microruban et coplanaire) soit mixte en combinant une alimentation coaxiale et une alimentation coplanaire. Caractéristiques principales des antennes à résonateur diélectrique (DRA): Pour répondre aux attentes des utilisateurs en termes de débit, les systèmes de communication sans fils se tournent vers des fréquences de plus en plus élevées. La conséquence de cette montée en fréquence est notamment l’augmentation des pertes au niveau des éléments conducteurs et donc une diminution de l’efficacité globale des systèmes de communication. Dans ces circonstances, les DRA offre de meilleurs résultats par rapport à d'autres familles d'antennes à base d’éléments métalliques. De plus, les DRA offrent des pertes diélectriques négligeables, elles sont peu sensibles aux variations de température et s’intègrent facilement sur des technologies de fabrication planaires / Technologies such as direct broad cast satellite system (DBSS), Geosynchronous Earth Orbit (GEO) and Low Earth Orbit (LEO) satellite communications , global positioning system (GPS), high accuracy airborne navigation system and a large variety of radar systems demand for high level of antenna performance. Similar is the requirement for upcoming land based wireless systems such as cellular and indoor communication systems that is needed some more specific and additional features added to the antenna to compensate for the deficiencies encountered in system's performance. Though metallic antennas are capable enough to fulfil all the operational requirements, however at very high frequencies and under hostile temperature conditions they are constrained to face certain limitations. To avoid these constraints the performance of Dielectric Resonator Antennas (DRAs) is evaluated and their new applications are proposed. In the thesis, two types of antenna applications are sought :-First is for tracking and satellite applications that needs a larger aperture coverage in elevation plane. This coverage is realized with a good CP purity by proposing two ports dual linearly polarized DRA working at X-band. The DRA is excited by two orthogonal H-shaped aperture slots yielding two orthogonal polarizations in the broadside direction. A common impedance bandwidth of 5.9% and input port isolation of -35 dB are obtained. The broadside radiation patterns are found to be highly symmetric and stable with cross polarization levels -15dB or better over the entire matching frequency band. The maximum measured gain is found to be 2.5dBi at 8.4 GHz.- The 2nd type of antenna is a dual pattern diversity antenna to be used in the Body Area Network (BAN) context. This antenna combines a slot loop and DRA yielding broadside and end-fire radiation patterns respectively. Based upon the feeding techniques, the DG antenna is further divided into two categories one with planar feeds and the other with non-planar feeds (slot loop excited by planar CPW but DRA excited by vertical monopole) .Both types are successfully designed and measured upon body when configured into different propagation scenarios. The non-planar feeds antenna allows wider common impedance bandwidths than the planar feeds (4.95% vs 1.5%).In both cases, a maximum value of DG=9.5dB was achieved when diversity performance tests were carried out in rich fading environments. This value is close to the one (10 dB) theoretically reached in a pure Rayleigh environment and was obtained with efficiencies of 70% and 85% for the slot loop and the DRA respectively. Therefore, we conclude that these antennas could be used on the shoulders or the chest of professional clothes (firemen, policemen, soldier) where full planar integration is not a key issue but where the communication must be efficient in harsh environments and for various gestures, positions and scenarios

The thesis deals with design of strengthening of existing bridge structure near the village Holýšov using modern method of additional presstresing. The bridge over the river of Radbuza is h-shaped beam bridge, which was built in 1924. In the present state its load capacity is under the limits for bridges situated on first-class roads. Original documentation of the bridge does not exist, the main source of information about construction details is the diagnostics research. The method of reinforcement by post-tensioning by cables in substituted cable ducts is highly efective in terms of the incerease the load capacity of existing bridge structure. The design of strengthening and the final load capacity was verified by static calculation.