The different technologies of passive cooling concepts have to rely on a good thermal coupling between a building's thermal mass and indoor air. In many cases, the ceiling is the only surface remaining for a good coupling. Further research is necessary to investigate discrepancies between existing correlations. Therefore, the overall aim of the work described in this thesis is the investigation of heat transfer at a heated ceiling in an experimental chamber. Acoustic baffles obstruct the surface of the ceiling and impede heat transfer. However, there is nearly no published data about the effect of such baffles on heat transfer. Available results from simulations should be verified with an experimental investigation. Consequently, one of the primary aims of this work was to experimentally determine the influence of such acoustic baffles. A suitable experimental chamber has been built at Biberach University of Applied Sciences. The thesis describes the experimental chamber, the experimental programme as well as results from five different test series. With a value of ±0.1Wm⁻²K⁻¹ for larger temperature differences, uncertainty in resulting convective heat transfer coefficients for natural convection is comparable to that of results from an existing recent experimental work often recommended for use. Additionally, total heat transfer (by convection and radiation) results are presented. Results are given for natural, forced and mixed convection conditions at an unobstructed heated ceiling. Furthermore, results for acoustic baffles in both an unventilated and a ventilated chamber are shown. Natural convection results show a very good agreement with existing correlations. Under mixed convection conditions, convective heat transfer at an unobstructed ceiling decreases to the limiting case described by natural convection. Installation of acoustic baffles leads to a reduction in total heat transfer (convection and radiation) between 20% and 30% when compared to the case of an unobstructed ceiling.

The issue of descaling is an important part of the forging and heat treatment of steel and semi products of steel production. Rising of new information and study of this process can increase efficiency and improve the surface quality after descaling. This thesis is focused on the mechanisms of the high pressure hydraulic descaling qualification and study of the chemical compounds of which the scales grown. To achieve all goals of this work and to get a comprehensive view of descaling process, few experimental measurements and numerical analyses were performed. All experimental measurements were focused on obtaining data about fundamental parameters and effects of the hydraulic descaling. The data obtained from measurements were applied to numerical analyses, which aimed to discover a deeper relation and to confirm the experimental results. This thesis can be divided into two main parts. The first part is devoted to parameters of the water jet study. The main studied characteristics of the high pressure hydraulic water jet were heat transfer coefficient and impact pressure at different modes such as standard or pulsating water jet. Experimentally measured data of these parameters were applied in numerical analyses. The numerical analyses were focused on studying the impact of the water jet parameters on the stresses in the oxide scale layers. A further water jet analysis was focused on the influence of the individual parts of the hydraulic system (such as water chamber or stabilizer) on its characteristics. In this part different types of the water chambers in combination with different types of stabilizers on the impact pressure values were investigated. These measurements were supported by fluid flow analysis through the hydraulic system. The second part of this work was focused on getting mechanical properties of the oxide scales from specimens prepared from standard structural steel and specimens from silicon steel. In this thesis, the influence of various parameters and characteristics was studied on these two types of steel. Mechanical properties of oxide scale structures were carried out by the Small Punch Test method. To obtain the fundamental mechanical properties such as Young´s modulus, yield strength and ultimate strength, material parameters based on the measured data were optimized. The whole work was carried out in order to get valuable and comprehensive results about high pressure hydraulic descaling process and influencing factors as well as about oxide scales themselves.

A pesquisa realizada tratou do estudo da transferência de calor e do fluxo crítico durante a ebulição convectiva no interior de canais de diâmetro reduzidos a partir de dados levantados em bancadas experimentais construídas para esta finalidade. Extensa pesquisa bibliográfica foi efetuada e os principais métodos disponíveis para previsão de coeficiente de transferência de calor, fluxo crítico e mapas de escoamento foram levantados. Os resultados obtidos foram parametricamente analisados e comparados com os métodos da literatura. Pela primeira vez para microcanais, resultados experimentais foram levantados por um mesmo autor em laboratórios distintos buscando verificar a tendência e comportamentos. Tal comparação tem sua importância destacada em face das elevadas discrepâncias observadas na literatura quando resultados de autores distintos, obtidos em condições similares, são comparados. Os resultados levantados foram utilizados na elaboração de modelos que consideram os padrões de escoamento observados em microcanais. A incorporação dos padrões permitiu o desenvolvimento de modelos mecanísticos para coeficiente de transferência de calor, fluxo crítico e critérios para a caracterização da transição entre macro e microcanais baseados na formação do padrão de escoamento estratificado e na simetria do filme líquido no escoamento anular. / This research comprises an experimental and theoretical study on flow boiling heat transfer and critical heat flux inside small diameter tubes based on data obtained in experimental facilities specially designed for this purpose. A broad literature review was carried out and the main methods to predict the heat transfer coefficient, critical heat flux and flow patterns were pointed out. The experimental results were parametrically analyzed and compared against the predictive methods from literature. For the first time, microchannels experimental results obtained by an unique researcher in distinct laboratories were compared and a reasonable agreement was observed. The importance of such a comparison is high-lighted for flow boiling inside microchannels due to the high discrepancies ob-served when results from independent laboratories obtained under similar experimental conditions are compared. Moreover, the experimental results obtained in the present study were used to develop correlations and models for the heat transfer coefficient and heat flux that takes into account the flow patterns observed in microchannels. The heat transfer coefficient and critical heat flux models were developed based on mechanistic approach. In addition, criteria to characterize macro to microchannel transition were proposed based in the occurrence of the stratified flow pattern and the liquid film symmetry under annular flow conditions.

A têmpera dos aços envolve a austenitização de uma peça seguida por um resfriamento rápido para promover a formação de microestrutura martensítica. É necessário avaliar os meios de têmpera para manter o processo de têmpera sob controle. Os parâmetros mais importantes no processo de resfriamento são o coeficiente de transferência de calor e/ou o fluxo de calor entre o meio de têmpera e a peça a ser resfriada. Um dos métodos de se avaliar os meios de têmpera (meios de resfriamento) e saber o que está acontecendo dentro da peça durante o resfriamento do ponto de vista térmico é o problema inverso de condução de calor. O problema inverso de condução de calor consiste na determinação de parâmetros como fluxo de calor, taxa de resfriamento e temperatura em qualquer posição através da peça, assim como o coeficiente de transferência de calor. Esses parâmetros são obtidos a partir de medições de temperatura em um ou mais pontos dentro da peça. O escopo deste trabalho foi desenvolver um software baseado no problema inverso condução de calor para avaliar meios de resfriamento para têmpera. A validação deste código foi feita usando água, óleo de soja, óleo mineral e solução aquosa de NaNO3. / Steels quenching involves part austenitization followed by a fast cooling to promote martensitic microstructure formation. It is necessary to evaluate quenchants in order to keep the quenching process under control. The most important cooling process parameters are the heat transfer coefficient and/or the heat flux between the quenchant and the part to be cooled. One of the methods to evaluate quenchants (cooling media) and to know what is happening inside the part during the cooling in the thermal point of view is the inverse heat conduction problem. The inverse heat conduction problem consists in the determination of parameters like heat flux, cooling rate and temperature in any position across the part, as well as the heat transfer coefficient. These parameters are obtained from temperature measurements in one or more points inside the part. The scope of this work was to develop a software based in the inverse heat conduction problem in order to evaluate quenchants for quenching. The validation of this code was made using water, soybean oil, mineral oil and NaNO3 aqueous solution.

Submitted by Maicon Juliano Schmidt (maicons) on 2015-05-25T14:45:18Z No. of bitstreams: 1 Bruno de Sá Beckerle.pdf: 3991624 bytes, checksum: 500b993c0f3a1c3a8c3abae05ed51c5e (MD5) / Made available in DSpace on 2015-05-25T14:45:18Z (GMT). No. of bitstreams: 1 Bruno de Sá Beckerle.pdf: 3991624 bytes, checksum: 500b993c0f3a1c3a8c3abae05ed51c5e (MD5) Previous issue date: 2015-01-05 / CAPES - Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Este trabalho apresenta um estudo experimental da transferência de calor e queda de pressão na ebulição do isobutano, R-600a, em um tubo composto por 7 mini canais paralelos, cujo diâmetro hidráulico é de 1,47 mm. Os testes em ebulição foram realizados com uma temperatura de saturação de 22 ºC e pressão de saturação de 302 kPa, com velocidade mássica entre 50 e 200 kg/(m²s) e fluxos de calor na seção de testes entre 7 e 40 kW/m². Com os testes realizados verificou-se que o coeficiente de transferência de calor aumenta conforme o incremento do fluxo de calor e velocidade mássica, sendo que esta última tem maior influência para baixos títulos de vapor. O coeficiente de transferência de calor atingiu valores máximos próximos a 3.200 W/(m²K) para a condição de maior vazão e fluxo de calor. A queda de pressão aumentou com o incremento da velocidade mássica e título de vapor em todos os testes, enquanto que o fluxo de calor apresentou influência na queda de pressão apenas nas maiores velocidades mássicas. A perda de pressão por atrito representou até 93,7% da perda total. Também foram analisados os padrões de escoamento, sendo observados os padrões de bolhas isoladas, bolhas alongadas, intermitente e anular, sendo que o padrão de bolhas isoladas foi observado para baixos fluxos e títulos de vapor, e o padrão anular mostrou-se presente para títulos superiores a 0,13. / This work presents an experimental study of heat transfer and drop pressure in flow boiling of the isobutane, R-600a, in a 7 mini channel of 1,47 mm hydraulic diameter. The tests were performed a boiling with a saturation temperature of 22 °C and saturation pressure of 302 kPa, with a mass velocity between 50 and 200 kg/(m²s) and heat fluxes in the test section between 7 and 40 kW/m². In the tests, it was found that the heat transfer coefficient increases with increasing heat flux and mass velocity has more influence at low quality. The heat transfer coefficient achieved values around 3.200 W/(m²K) for the condition of greater flow and heat flux. The drop pressure was increase by increasing the mass velocity and quality in all tests, while the heat flow have any influence on the drop pressure to the greater mass velocity. The friction drop pressure represented to 93.7% of the total loss. As well analyzed the flow patterns, and observing the patterns of isolated bubbles, plugs/slugs, intermittent and annular, and that the pattern of isolated bubbles were observed for low quality and heat flux and the annular pattern was present for quality from 0.13.

No presente trabalho são relatados os resultados obtidos por meio de ensaios de caracterização para os diferentes tipos de óleos vegetais (algodão, canola, girassol, milho e soja), no estado novo e puro, tais como viscosidade, número de acidez, índice de iodo, índice de saponificação, cromatografia gasosa, curvas de resfriamento e coeficiente de transferência de calor. Esses mesmos ensaios foram realizados também com as amostras de óleo de soja com diferentes concentrações de aditivos antioxidantes. As diferentes formulações feitas com óleo de soja foram submetidas a um processo de envelhecimento acelerado (durante 72 horas), suas propriedades foram comparadas com as de dois óleos minerais utilizados para têmpera. O mesmo foi feito para os óleos vegetais, estes porém foram envelhecidos durante 48 horas. Pode-se então, comparar qual amostra sofreu menor oxidação durante um mesmo tempo de envelhecimento e, desta maneira, avaliar qual aditivo antioxidante obteve melhor desempenho, retardando o processo de oxidação no óleo de soja. Esses estudos também permitiram verificar qual, dentre os óleos vegetais, possui as melhores propriedades para ser utilizado no tratamento térmico de têmpera. Amostras do aço AISI 4140 foram temperadas nos diferentes óleos estudados, obteve-se a curva de dureza e as micrografias óticas para cada amostra temperada. / In this work, the results obtained from the characterization of different vegetable oils (cotton, canola, sunflower, corn and soybean) are reported. The oils were evaluated at \"new condition\" and \"pure\" by viscosity, acid and iodine number, saponification, gas chromatography, cooling curves and heat transfer coefficient. These same analyses were also performed on samples of soybean oil containing various concentrations of antioxidant. The various formulations prepared with soybean oil were accelerated aged for 72 hours and their properties were compared with two mineral oils used for quenching. Likewise, the vegetable oils were aged for 48 hours long. Therefore, it was possible to identify which sample exhibited the lower oxidation process at the same aging time and, thus, evaluate the antioxidant additive that promoted the improved oxidation performance for soybean oil. Also, these studies allowed verifying which of the vegetable oils had the best properties to be used as quenchants. Samples of AISI 4140 steel were quenched in different oils and the hardness curve and optical microscopy for each sample were obtained.

An experimental investigation has been carried out to study the heat transfer in a two-phase two-component mixture flowing upward inside a 1" double pipe heat exchanger. The heat transfer coefficient was measured using either air to lift the liquid (air-lift system) or a mechanical pump. The heat transfer coefficient results have been extensively studied and compared with other workers' results. An attempt was made to correlate the present heat transfer data in dimensionless correlations. Possible factors affecting the two-phase heat transfer coefficient have been studied with special attention being given to the fluid properties, particularly the liquid viscosity. Experiments were also carried out to investigate the effect of solid particles added to a liquid flow on the measured heat transfer coefficient. The present investigation was carried out using air as the gas-phase ranging from 2x 10-5 up to 80 x 10-5 m3/s. Liquids used were water and glycerol solutions with viscosity ranging from 0.75 up to 5.0 C. P. and flowrates between 4x 10-5 and 25 x 10-5 m3/s. Void fraction and pressure drop were also measured during the heat transfer process. Flow pattern in gas-liquid mixture was investigated in a perspex tube of identical dimensions to the heat exchanger tube.

Det finns stora vinningar att göra inom både transport- och industrisektorn genom att effektivisera materialanvändningen i produkter. Denna vinning återfinns i både materialkostnader och energieffektivisering. Scandymet AB är ett företag som tillverkar värmeväxlare och elektriska doppvärmare för ytbehandlingsindustrin. Denna rapport syftar till att utvärdera hur väl ett kalkylark som används som underlag för dimensionering av värmeväxlare hos företaget stämmer överens med verkligheten. En testrigg har därför konstruerats för att undersöka kalkylarkets validitet gällande temperaturer under 46 grader Celsius. I rapporten redovisas resultaten av tester på fyra olika värmeväxlare och resultaten har jämförts med företagets kalkylark. Undersökningarna visar att två av dessa värmeväxlare är överdimensionerade och två värmeväxlare stämde väl överens med kalkylarket. I samtliga tester används vatten som media, men då Scandymet AB värmeväxlares huvudsakliga användningsområde är korrosiva vätskor dras slutsatsen att fler undersökningar med andra fluider skulle behövas för att ytterligare fördjupa kunskapen inom värmeväxlarnas korrekta dimensionering. / There are huge gains in both the transport and industry sectors by making material use more efficient in products. This gain is found in both material costs and energy efficiency. Scandymet AB is a company that manufactures heat exchanger and electric immersion heaters for the surface treatment industry. This report aims to evaluate how well a spreadsheet used as basis for the dimensioning of heat exchangers at the company is consistent with reality. A test rig has therefore been designed and constructed to investigate the validity of the spreadsheet. The report presents the results of tests on four different heat exchangers and the results have been compared with the company’s spreadsheet. In all tests water has been used as the media to be heated, but since Scandymet AB’s heat exchanger’s main application is corrosive liquids, therefore I consider that a deeper investigation with additional fluids would be necessary to further deepen the knowledge in the area.

Made available in DSpace on 2014-06-11T19:23:38Z (GMT). No. of bitstreams: 0 Previous issue date: 2010-12-20Bitstream added on 2014-06-13T19:47:44Z : No. of bitstreams: 1 souza_eg_me_ilha.pdf: 959550 bytes, checksum: b4784dbcc883b1be2d0c6b7cce83f54b (MD5) / Fundação de Ensino Pesquisa e Extensão de Ilha Solteira (FEPISA) / O objetivo deste trabalho é a análise numérica e experimental de escoamento viscoso, incompressível, permanente, com transferência de calor, em um canal estreito contendo um arranjo de obstáculos retangulares. A análise experimental envolveu determinação de coeficiente de transferência de calor médio bem como o número de Nusselt médio e medidas de temperatura em esteira térmica para comparação com os resultados obtidos por simulação numérica. Para a análise numérica usamos o programa comercial de mecânica dos fluidos e transferência de calor computacional ICEPAK®. Verificamos que quanto mais adentro o obstáculo estiver no arranjo maior é a transferência de calor por convecção forçada. Determinamos coeficientes de transferência de calor médio e número de Nusselt médio (com incerteza entre 6 e 15%) e verificamos que o efeito da posição diminui à medida que a velocidade aumenta. Concluímos também que ambos os modelos de turbulência utilizados, k-ε padrão e k-ε RNG, foram incapazes de predizer o efeito da posição apropriadamente. Entretanto, o modelo k-ε RNG apresentou melhor comportamento, pois o seu uso resultou em soluções com valores de temperatura intermediários aos experimentais / The purpose of this work is the study of the numerical and experimental viscous incompressible steady flow with heat transfer into a narrow channel containing a rectangular array of obstacles. The experimental approach involves determining the coefficient of heat transfer and temperature measurements in thermal wake for comparison with the results obtained in numerical simulations. For the numerical analysis we use the commercial program of fluid mechanics and heat transfer computational ICEPAK™. We confirmed that in the last lines of the array the biggest is the heat transfer by forced convection. We determined the average heat transfer coefficients (with uncertainty between 6 and 15%) and found that the effect of the position decreases as flow speed increases. We use in the simulations the k-ε turbulence model and the k-ε RNG turbulence model. We conclude that both turbulence models used were unable to predict the effect of the position properly. However, the k-ε RNG model showed better behavior. The numerical temperatures with this model were consistent to the experimental temperature

Orientador: Rezende Gomes dos Santos / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica / Made available in DSpace on 2018-08-09T22:01:50Z (GMT). No. of bitstreams: 1 Eid_MarcoAntonio_M.pdf: 19245694 bytes, checksum: b272ecb88a2fa2a6affcf2a60d7e8d47 (MD5) Previous issue date: 2007 / Resumo: Apesar da importância tecnológica da solidificação de ligas metálicas sob fluxo de calor radial, relativamente poucos estudos estão sendo feitos nessa área. Neste trabalho, a solidificação da liga Al 4,5%Cu em molde de aço radial cilíndrico é analisada e comparada com a solidificação direcional em molde resfriado.Inicialmente a variação de temperatura em diferentes posições no metal e no molde foi medida durante a solidificação usando um sistema de aquisição de dados. Essas variações de temperatura foram introduzidas em um método numérico para determinar a variação do coeficiente de transferência de calor na interface metal/molde pelo método inverso. Os resultados para a solidificação unidirecional e radial foram comparados mostrando que o coeficiente de transferência de calor para o fluxo de calor radial é menor. A variação dos espaçamentos dendritos secundários foram medidos através de um microscópio óptico. Comparações entre os resultados mostraram maiores espaçamentos para fluxo de calor radial. Comparações entre variações e temperaturas calculadas numéricas e experimentalmente comprovaram que o método numérico descreve satisfatoriamente o processo de solidificação radial / Abstract: In spite of technological importance of solidification of metallic alloys under radial heat flow, relatively few studies have been carried out in this area. In this work the solidification of Al 4.5 wt% Cu cylinders against a steel massive mold is analyzed and compared with unidirectional solidification against a cooled mold. Initially temperature variations at different positions in the casting and in the mold were measured during solidification using a data acquisition system. These temperature variations were introduced in a numerical method in order to determine the variation of heat transfer coefficient at metal/mold interface by inverse method. The results for unidirectional and radial solidification were compared showing that the heat transfer coefficient is smaller for radial heat flux. The primary and secondary dendrite arm spacing variations were measured through optical microscopy. Experimental results for temperature variations were applied to estimate thermal parameters of the solidification process. Comparisons carried out between experimental and numerical data showed that the numerical method describes well the solidification processes under radial heat flux / Mestrado / Materiais e Processos de Fabricação / Doutor em Engenharia Mecânica