It is a great challenge in the design of the PBMR to accurately predict gas flow and heat transfer in the reactor. Understanding the heat transfer at the core-reflector interface in particular is a very important aspect as the reactivity of the control rods housed in the reflectors is highly temperature dependent. It is also very important because the core-reflector interface is on the critical path for heat removal during accident conditions. PBMR has developed an OECD/NEA coupled neutronic/thermal-hydraulic benchmark to aid in the understanding of the different modelling approaches currently employed at PBMR. A comparison of THERMIX-KONVEK and DIREKT results showed large temperature differences at the core-reflector interfaces. Further investigation showed that these differences are as a result of the numerical methods used i.e. Cell-Centred (CC) vs. Vertex-Centered (VC). The present study extended this comparison to Star-CD (CC) and Flownex (VC) which are also used to simulate the reactor at PBMR. An ID MATLAB program that mimics the CC and VC numerical methods was verified against Star-CD and Flownex. This program was then used to model an ID version of the OECD/NEA benchmark. Results were compared with DIREKT and THERMIX-KONVEK. Although the results compared well, there were significant errors at the core-reflector interfaces. The findings of this study were that different numerical methods will predict different temperatures, heat fluxes and (temperature-dependent) sink terms. It was also shown that in addition to the differences resulting from numerical methods, differences were seen between Star-CD and DIREKT and Flownex and THERMIX-KONVEK in the region of the core-reflector boundary. In general, for complicated simulations like that of the pebble bed, the numerical basis of software used to simulate the problem needs to be understood for the problem to be correctly modelled. / Thesis (M.Sc. Engineering Sciences (Nuclear Engineering))--North-West University, Potchefstroom Campus, 2010.

Traditional Balinese architecture is commonly related to culture and traditional reasoning. When subjected to several modem problems such as energy demand, pollution, and impact of urbanisation and tourism, traditional architecture becomes less attractive since the definitions behind traditional reasoning are not clear and can be interpreted in different ways. To understand this feature, the study of traditional Balinese architecture starts by using several key parameters such as wind engineering and heat transfer, as presented and used in several countries. The flow patterns around a cubic building have been studied by many researchers. The velocity profile at the model position and the local surface roughness are specific to each building model and cannot be estimated from general tests of a standard building shape, therefore specific velocity profiles and conditions are used in this particular study. The air flow around a cluster of traditional Balinese buildings is extremely complicated and difficult to determine by modelling an isolated building (via symmetric conditions) since the buildings are linked to each other. Full scale models of traditional buildings have been investigated by using CFD to predict the above aspects. Simulations using this method can be done more quickly and less expensively than with wind tunnel experiments, and are capable of delivering more detailed and comprehensive information about the flow structure. Two-dimensional models of traditional Balinese building arrangements are simulated by using a commercial code Fidap based on the finite element method to assess the effects of type of roof, fence and surface roughness. Three-dimensional models are simulated by using a commercial code CFX based on the finite volume method to verify some traditional definitions. A standard к-ε model is adopted because it needs less computational power and has achieved notable successes in calculating a wide variety of thin shear layer and recirculating flows without the need of adjustment of the model constants, but with the imposition of boundary conditions to reduce the over-prediction near windward edges. Adopting lower values of к and ε combined with multi-blocks is shown to reduce this over-estimation. For a cubic building, the results can be compared with several other turbulence models. It appears that traditional Balinese architecture has a strong and significant correlation with several engineering fields, therefore traditional communities can develop by considering the Tri Hita Karana concept in order to improve thermal comfort and reduce cooling loads, with corresponding energy savings.

There is a demand for a whole field velocimetry technique which offers the capability of rapid characterisation of complex engineering flow fields. This thesis describes a research programme aimed at the development of a reliable Doppler global velocimeter, suited to the measurement of such flows. The programme of work undertaken is discussed with reference both to research undertaken elsewhere and to previous work on the system at Oxford. While much of the underlying technology required for the construction of an accurate and reliable velocimeter has already been studied in Oxford and elsewhere, little attention has been paid by previous workers to the examination of the impact of data processing techniques on attainable flow measurement accuracy. In the present work, a number of image processing methods have been utilised for Doppler global velocimetry data processing. Those methods are described here, together with a theoretical analysis of their expected performance when applied to Doppler global velocimetry data. The expected error resulting from image processing considerations and also from the physical characteristics of the Doppler global velocimetry hardware are quantified in such a way that error estimates may be computed for real measured data frames. The results of the application of the velocimeter to the simple test case of measuring a velocity component of a rotating disc are presented. The velocimeter was subsequently applied to the measurement of a free jet flow and to a transonic flow field in a convergent-divergent nozzle. Correlations with accepted velocity field values were undertaken, and compared to the expected error previously determined. The choice of image processing algorithms was found to be of great importance in terms of Doppler global velocimetry measurement accuracy.

During the impinging heat transfer, a jet of working fluid, either gas or liquid, will besprayed onto the heat transfer surface. Due to the high turbulence of the fluid, the heat transfer coefficient between the wall and the fluid will be largely enhanced. Previously, an impinging type solar receiver with a cylindrical cavity absorber was designed for solar dish system. However, non-uniform temperature distribution in the circumferential direction was found on absorber surface from the numerical model, which will greatly limit receiver's working temperature and finally affect receiver's efficiency. One of the possible alternatives to solve the problem is through modifying the roughness of the target wall surface. This thesis work aims to evaluate the possibility and is focusing on the study of heat transfer characteristics. The simulation results will be used for future experimental impinging solar receiver optimization work. Computational Fluid Dynamics (CFD) is used to model the conjugate heat transfer phenomenon of atypical air impinging system. The simulation is divided into two parts. The first simulation was conducted with one rib arranged on the target surface where heat transfer coefficient is relatively low to demonstrate the effects of rib shape (triangular,rectangular, and semi-circular) and rib height (2.5mm, 1.5mm, and 0.5mm). The circular rib with 1.5mm height is proved to be most effective among all to acquirerelatively uniform temperature distribution. In the second part, the amount of ribs is taken into consideration in order to reach more uniform surface heat flux. The target wall thickness is also varied to assess its influence.

A measurement-based reduced-order heat transfer modeling framework is developed to optimize cooling costs of dynamic and virtualized data centers. The reduced-order model is based on a proper orthogonal decomposition-based model order reduction technique. For data center heat transfer modeling, the framework simulates air temperatures and CPU temperatures as a parametric response surface with different cooling infrastructure design variables as the input parameters. The parametric framework enables an efficient design optimization tool and is used to solve several important problems related to energy-efficient thermal design of data centers. The first of these problems is about determining optimal response time during emergencies such as power outages in data centers. To solve this problem, transient air temperatures are modeled with time as a parameter. This parametric prediction framework is useful as a near-real-time thermal prognostic tool. The second problem pertains to reducing temperature monitoring cost in data centers. To solve this problem, transient air temperatures are modeled with spatial location as the parameter. This parametric model improves spatial resolution of measured temperature data and thereby reduces sensor requisition for transient temperature monitoring in data centers. The third problem is related to determining optimal cooling set points in response to dynamically-evolving heat loads in a data center. To solve this problem, transient air temperatures are modeled with heat load and time as the parameters. This modeling framework is particularly suitable for life-cycle design of data center cooling infrastructure. The last problem is related to determining optimal cooling set points in response to dynamically-evolving computing workload in a virtualized data center. To solve this problem, transient CPU temperatures under a given computing load profile are modeled with cooling resource set-points as the parameters.

Direct contact condensation of steam injected into water is a special mode of condensation where condensation occurs on the interface between steam and water. This type of condensation forms an essential part of various industrial applications and correct prediction and modelling of the condensation behaviour is crucial to obtain an optimised design of such devices. While present prediction models for direct contact condensation are valid for a limited range of flow conditions only, the work presented in this thesis provides improved models for direct contact condensation. The models are developed in the form of diagrams and include: a condensation regime diagram, for predicting the condensation behaviour, a steam plume length diagram, for predicting the penetration distance of steam into water, and a heat transfer coefficient diagram. These models are derived using a wide range of data and therefore provide more accurate predictions compared with alternative models available in literature. In contrast to present models, the derived models presented in this work are constructed using an additional physical parameter to describe the process. The diagrams are validated against independent experiments and demonstrate close agreement. Furthermore, the predictions from the condensation regime diagram and steam plume length diagram are self-consistent. The models developed in this study are capable of predicting condensation behaviour for a wide range of initial conditions and can be used in conjunction with computational fluid dynamics techniques for direct contact condensation.

Metal foams and wire meshes are open cell structures with low weight and density, high permeability and high thermal conductivity which make them attractive for a wide range of industrial applications involving fluid flow and heat transfer. In this study, the effect of natural convection, radiation and heat transfer enhancement of metal foams and wire meshes of 10 and 40 PPI (pores per inch) heat exchangers were examined and compared for different heat exchanger orientation, coolant flow rate and atmosphere temperature. Thermal spray coating processes were also used in development of a new class of high temperature stainless steel heat exchangers. Stainless steel wire mesh heat exchangers were prototyped by connecting the tube to the wire mesh using wire arc thermal spray coating. Thermal spray coating provided efficient connections between the wire mesh and the tubes’ outer surface, and has potential to replace expensive brazing or other metal connection techniques.

There has been an ever-increasing demand for power generation, which is predicted to grow as society becomes more advanced. However, tradition fossil fuels are beginning to deplete, and there is a great necessity for alternative fuel sources that will bridge the gap between energy production and consumption. To decrease the high demand alternative fuel sources are gaining in popularity. The supercritical carbon dioxide Brayton power cycle has been proposed as a possible cycle for nuclear and concentrated solar power generation. Two main advantages of having supercritical carbon dioxide are the large property variations and component size associated with power cycle. Forced convection heat transfer of supercritical carbon dioxide in printed circuit heat exchanger geometries were investigated in the following study using a finite volume framework and the FLUENT 12.1 code. The geometries of interest were: non- chamfered zig-zag, chamfered zig-zag, and air foil. Flow through the three geometries was in the horizontal orientation and subject to a heating mode operation. A range of testing conditions were explored, including operating pressures between 7.5 to 10.2 MPa with the mass flux ranging from 326 to 762 kg/m2-s. Due to the turbulent nature of this problem, the k−E with enhanced wall treatment and shear stress transport k−ω turbulence models were considered. With this addition a total of 54 simulations were performed. Results indicated that there was an increase in the heat transfer coefficient as the supercritical carbon dioxide reached the pseudocritical temperature, conversely as there was an increase in operating pressure, the heat transfer coefficient decreased. Nevertheless, this increase near the pseudocritical temperature was due to a sharp increase in the specific heat. Mass flux effects indicated that there was an increase in heat transfer as the mass flux was increased. This was due to the increase in Reynolds number near the pseudocritical temperature. Next, pressure losses were investigated for the three geometries. The non-chamfered zig-zag channel had the greatest pressure loss associated with it, while the air foil channel had the least. Based on the results, the ratio of the friction factor to heat transfer for the non-chamfered and chamfered zig-zag geometries were approximately 2.65 and 1.57 times higher than for the air foil, thus leading to the idea that the air foil channel may be best suited for practical applications. Finally, the simulation results were compared to experimental data and existing correlations. Many existing correlations failed to accurately predict the magnitude of heat transfer, although they exhibited a similar trend. A new correlation was developed for the zig-zag geometries based on the numerical data obtained during this investigation and published experimental data. The new correlation is able to predict the maximum heat transfer coefficient within 12.4%.

In this study, the application of a Monte Carlo method (MCM) for radiative heat transfer in three-dimensional rectangular enclosures was investigated. The study covers the development of the method from simple surface exchange problems to enclosure problems containing absorbing, emitting and isotropically/anisotropically scattering medium. The accuracy of the MCM was first evaluated by applying the method to cubical enclosure problems. The first one of the cubical enclosure problems was prediction of radiative heat flux vector in a cubical enclosure containing purely, isotropically and anisotropically scattering medium with non-symmetric boundary conditions. Then, the prediction of radiative heat flux vector in an enclosure containing absorbing, emitting, isotropically and anisotropically scattering medium with symmetric boundary conditions was evaluated. The predicted solutions were compared with the solutions of method of lines solution (MOL) of discrete ordinates method (DOM). The method was then applied to predict the incident heat fluxes on the freeboard walls of a bubbling fluidized bed combustor, and the solutions were compared with those of MOL of DOM and experimental measurements. Comparisons show that MCM provides accurate and computationally efficient solutions for modelling of radiative heat transfer in 3-D rectangular enclosures containing absorbing, emitting and scattering media with isotropic and anisotropic scattering properties.

EFFECTS OF OFF-CENTER ANGLE ON THE HEAT TRANSFER COEFFICIENT ON VERTiCAL TIER OF MULTIPLE SPHERICAL SURFACES Kaya, Ebubekir M.S., Department of Mechanical Engineering Supervisor: Assoc. Prof. Dr. Cemil Yamali December 2004, 112 pages The purpose of this study is to investigate the laminar film condensation phenomenon of steam on a vertical tier of multiple spherical surfaces by using both analytical and experimental methods. The analytical heat transfer results were obtained by following the Nusselt type of analysis and represented graphically. In addition, in order to observe the real behavior of the film condensation, an experimental setup was manufactured and experiments were done. In analytical section / mass flow rate, (mean) velocity, film thickness, local heat flux and local heat transfer coefficient values were obtained and plotted as depending on angular position. Moreover, mean heat flux and mean heat transfer coefficient variations were presented with respect to diameter of the sphere and sub-cooling. On the other hand, for the experimental section, heat flux and mean heat transfer coefficient values were obtained and expressed as depending on sub-cooling. To see the effects of off-center angle, setup was inclined for different angles and experiments were repeated for each inclination angle. At the end of the study, mean heat transfer coefficients belong to analytical and experimental studies were compared to each other as well as to the literature.