In this research an innovative combination of the Herschel-Quincke tubes and traditional liners is proposed for application in noise reduction of aircraft engines. The approach consists of installing Herschel-Quincke (HQ) tubes on lined rectangular ducts. An analytical model was developed to predict the effects of HQ tubes applied to rectangular lined ducts. The technique involves assuming the tube-duct interfaces as finite piston sources. These sources couple the acoustic field inside the duct with the acoustic field within the HQ tubes. The accuracy of the analytical model was validated with experimental data. Three different types of experimental configurations were tested: liner only, HQ tube with a hard wall duct, and HQ tubes with liners. Analytical predictions were shown to correlate well with the experimental data. Two typical types of liners, perforate and linear, were tested in these investigations. The perforate and linear liners with HQ systems showed better sound attenuations than the HQ tubes with hard walled ducts and liners only systems. The performance of the perforate and linear liners with HQ tubes were investigated in various configurations. The results indicated possible combinations which show great potential for reducing the noise within the ducts. / Master of Science

The combination of traditional passive acoustic liners with Herschel-Quincke (HQ) waveguides is proposed in this work as a device for Turbofan Engine Noise Control. The approach consists of installing circumferential arrays of HQ tubes on the lined sector of the inlet of a turbofan engine. A theoretical model is developed to predict the performance of this system assuming that the engine inlet is a circular lined duct with uniform mean flow. The tube-duct interfaces are modeled as finite piston sources that couple the sound field inside the duct with the dynamics of the HQ tubes. The finite piston source radiation is modeled in terms of a new closed form Green's function, which is found as the solution of the non-homogeneous convected acoustic wave equation with soft wall boundary conditions. The Green's function is extended from a point source to a finite piston by using the Divergence Theorem in the appropriate form. The dynamics of the HQ tube are both modeled as plane waves inside a straight tube and experimentally determined. The experimental determination of the HQ-dynamics is undertaken using impedance tubes with a 4-microphone technique. The newly developed theoretical model was used to predict the performance of a combined HQ-Liner system, which was tested on a scale simulated turbofan rig. The model is validated for broadband noise with the experimental data obtained from this test rig. The analytical predictions are shown to correlate well with experimental data. The results of the application of a HQ-Liner on a turbofan engine show a great potential in order to improve the performance of traditional passive acoustic liners. / Ph. D.

Commercial aviation transportation has experienced an overwhelming growth over the years. However, this expansion has encountered an important barrier: noise. Several studies have shown that residents in these areas experience problems such as stress and sleep disturbance. These problems have translated into demands for a better quality of life from airport residents which in turn have translated into more stringent aircraft noise regulations. As a result, large amounts of resources have been diverted towards the improvement of existing noise attenuation technologies and the development of more effective ones. In terms of turbofan generated noise, the most widely used technology is that of absorbent materials or liners. In recent investigations Alonso et al. have combined Herschel/Quincke (HQ) tubes with liners. This combination has the potential of effectively controlling pure tones and broadband noise in inlet sections of modern turbofan engines. Since a comprehensive approach for engine noise reduction will involve both inlet and aft HQ-Liner systems, additional research efforts were needed to evaluate their performance at reducing aft fan radiation In the present work, a combination of traditional liners and Herschel/Quincke waveguide resonators for aft fan radiation control is proposed. A theoretical model is developed in order to predict noise reduction due to such systems. The newly developed tool was then utilized to design an HQ-liner that was installed and tested in the aft section of the NASA Active Noise Control Fan (ANCF) rig. This experimental data was utilized to prove the potential of these systems and to validate the mathematical model. Analytical predictions correlate well with experiments. The NASA ANCF rig is not representative of a real turbofan engine. In order to assess the behavior of HQ-Liners in a more realistic environment a new system was specifically designed for a generic turbofan engine and its performance analyzed. The sound field inside HQ tubes has been described assuming plane waves only. This assumption limits the model to frequencies below the tube first resonance. In order to overcome this limitation a new model accounting for higher order modes inside the tubes has been developed. / Ph. D.

An innovative implementation of the Herschel-Quincke tubes concept for the reduction of noise from turbofan engines is proposed here. The approach consists of installing circumferential arrays of Herschel-Quincke (HQ) tubes or waveguides in the inlet of the turbofan engine. An analytical technique was developed to predict the effects of HQ tubes applied to circular inlets. The modeling technique involves modeling the tubes-inlet interfaces as finite piston sources that couple the acoustic field inside the inlet with the acoustic field within the HQ tubes. An optimization technique based on genetic algorithms was also developed to be able to design and optimize the system parameters. The accuracy of the model was validated with experimental data obtained from two types of turbofan engines. Analytical predictions are shown to correlate well with experimental data. The analytical model is then used to provide insight into the noise control mechanisms involved in the system. It is shown that the energy in an incident mode is in part reflected back to the fan and that some energy is also scattered into other higher-order modes. Thus, the suppression of a particular mode is due to the combination of the scattered contributions from the various incident modes. The effects of the system parameters were analyzed and parametric studies were conducted. Different configurations for the arrays of HQ tubes such as helical patterns or tubes at an angle with respect to the inlet axis were also investigated. The results show the great potential of the HQ tubes system to reduce noise from turbofan engines. / Master of Science

A fundamental study of the Herschel-Quincke (HQ) tube concept for the reduction of noise in circular ducts is presented here. Recent testing of the Herschel-Quincke tube concept on the Pratt-Whitney JT15D and AlliedSignal TFE731-60 engines showed the potential for the practical application of this approach. A model of the HQ-system has been developed to aid in the design of the system tested. The model has revealed new noise control mechanisms associated to the implementation of multiple HQ-waveguides in a duct in the presence of higher order modes. However, the practical nature of these engine facilities results in limitations with regard to the fundamental research knowledge that could be gained from testing in a more controlled laboratory environment. A series of experiments was conducted at the NASA Langley Research Center 0.30 m ducted fan test facility where detailed modal measurements were performed. The main goals of this research endeavor were to evaluate the accuracy of the previously developed theoretical model and provide insight into the noise control mechanisms. Experiments were performed with different disturbance mode structures, number of HQ tubes and arrays, and axial positions. The modes in the duct were generated with an array of acoustic drivers (no flow case) and measured with logarithmically spaced circumferential and helical microphone arrays located on the duct wall. The modal amplitudes of the incident, transmitted, and reflected modes in the duct were determined from the microphone measurements. This allowed for the comparison of analytical and experimental modal amplitudes, modal powers, total power, and reductions. The results of this study provide insight into the three noise control mechanisms associated with this approach: reflection, circumferential scattering, and radial scattering. Comparison with the experimental results shows that the model accurately predicts the sound power attenuation except near the cut-off frequency of the modes where it tends to overestimate the attenuation. The effect of the number of tubes in the array and its axial position was also evaluated. Overall, the results of this study validate the general modeling approach for the HQ tube concept. / Master of Science

The application of the Hershcel-Quincke (HQ) tube as a noise reduction device for one-dimensional plane-wave sound fields has been studied in great detail in previous years. In this thesis, an analytical technique is developed to investigate the potential of the HQ tube concept to control higher-order duct modes. This analytical method involves modeling the tube-duct interfaces as finite piston sources, which couple the acoustic field inside the main duct with the acoustic field within the HQ tube(s). The acoustic field within the HQ tube is modeled as plane-waves and the acoustic field within the main duct is modeled by expanding the sound field in terms of the higher-order modes. This model is then used to investigate the noise reduction mechanisms behind the attenuation of higher-order modes. These mechanisms involve both the reflection of the incident wave as well as the reconstruction and recombination of the modal content of the incident disturbance into other modes. The effects of the modal content of the disturbance along with the HQ tube geometric parameters, such as tube axial position, length, distance between interfaces, and cross-sectional area, are studied with respect to the frequencies of attenuation and the reduction obtained. These results show the potential of the Herschel-Quincke tube concept to reduce higher-order modes in ducts. / Master of Science

Excessive fluid-borne noise in hydraulic systems is a problem the fluid power industry has long struggled to address. Traditional noise control devices such as Helmholtz resonators, tuning coils, and Herschel-Quincke tubes are generally too large for fluid power systems unless the speed of sound in the device can be reduced. A compliant lining can achieve this effect, but compliance (and lossy compliance) has had little attention in noise control in general, and in fluid power in particular. One means to achieve compliance in these devices, especially at elevated pressures, is through a liner made of syntactic foam, which in this case is a urethane host matrix with embedded hollow, polymer microspheres. The material properties at elevated pressure are unknown by the liner manufacturer, but are known to be pressure- and temperature-dependent. Therefore, the effect of hydrostatic pressures from 2.1-21 MPa and temperatures from 20-45 C on the liner properties, thus the device performance, are studied. For a Helmholtz resonator, a theoretical model is fit to experimentally-measured transmission loss of the device using a least-squares routine, which solves the inverse problem for the complex bulk modulus of the liner. These material properties are used to compare a predictive model of a tuning coil to experimental data, and in a parameter study of a Herschel-Quincke tube. The compliance of the liner is found to lower the effective sound speed by an order of magnitude and decrease the volume of the cavity of a Helmholtz resonator by up to two orders of magnitude. This work is expected to result is more compact noise control devices for fluid power systems.

New methodologies and concepts for developing compact and energy efficient automotive exhaust systems have been studied. This originates in the growing concern for global warming, to which road transportation is a major contributor. The focus has been on commercial vehicles—most often powered by diesel engines—for which the emission legislation has been dramatically increased over the last decade. The emissions of particulates and nitrogen oxides have been successfully reduced by the introduction of filters and catalytic converters, but the fuel consumption, which basically determines the emissions of carbon dioxides, has not been improved accordingly. The potential reduction of fuel consumption by optimising the exhaust after-treatment system (assuming fixed after-treatment components) of a typical heavy-duty commercial vehicle is ~4%, which would have a significant impact on both the environment and the overall economy of the vehicle. First, methodologies to efficiently model complex flow duct networks such as exhaust systems are investigated. The well-established linear multiport approach is extended to include flow-acoustic interaction effects. This introduces an effective way of quantifying amplification and attenuation of incident sound, and, perhaps more importantly, the possibility of predicting nonlinear phenomena such as self-sustained oscillations—whistling—using linear models. The methodology is demonstrated on T-junctions, which is a configuration well known to be prone to self-sustained oscillations for grazing flow past the side branch orifice. It is shown, and validated experimentally, that the existence and frequency of self-sustained oscillations can be predicted using linear theory. Further, the aeroacoustics of T-junctions are studied. A test rig for the full determination of the scattering matrix defining the linear three-port representing the T-junction is developed, allowing for any combination of grazing-bias flow. It is shown that the constructive flow-acoustic coupling not only varies with the flow configuration but also with the incidence of the acoustic disturbance. Configurations where flow from the side branch joins the grazing flow are still prone to whistling, while flow bleeding off from the main branch effectively cancels any constructive flow-acoustic coupling. Two silencer concepts are evaluated: first the classic Herschel-Quincke tube and second a novel modified flow reversal silencer. The Herschel-Quincke tube is capable of providing effective attenuation with very low pressure loss penalty. The attenuation conditions are derived and their sensitivity to mean flow explained. Two implementations have been modelled using the multiport methodology and then validated experimentally. The first configuration, where the nodal points are composed of T-junctions, proves to be an example where internal reflections in the system can provide sufficient feedback for self-sustained oscillation. Again, this is predicted accurately by the linear theory. The second implementation, with nodal points made from Y-junctions, was designed to allow for equal flow distribution between the two parallel ducts, thus allowing for the demonstration of the passive properties of the system. Experimental results presented for these two configurations correlate well with the derived theory. The second silencer concept studied consists of a flow reversal chamber that is converted to a resonator by acoustically short-circuiting the inlet and outlet ducts. The eigenfrequency of the resonator is easily shifted by varying the geometry of the short circuit, thus making the proposed concept ideal for implementation as a semi-active device. Again the concept is modelled using the multiport approach and validated experimentally. It is shown to provide significant attenuation over a wide frequency range with a very compact design, while adding little or no pressure loss to the system. / QC 20110208