High hardness steels can be affected by delayed brittle cracking often attributed to hydrogen embrittlement. Improved resistance to hydrogen embrittlement would be beneficial to many industries including military, automotive, and high-rise construction. While other prevention methods include coating, trapping, and barriers, design efforts in this study were focused on improving intrinsic properties to be more resistant to hydrogen embrittlement. Four alloys targeting 477 – 534 HB were designed and produced in-house and compared against a commercial grade 500 HB alloy. Charpy V-notch (CVN) impact toughness and tensile specimens were made according to ASTM E23 and ASTM E8 to characterize mechanical properties. Hydrogen embrittlement testing was performed using ASTM E8 test samples electro-chemically charged in either sodium hydroxide or sulfuric acid with thiourea in solution. Results suggested that alloying for lower strength and better toughness by reducing C and Mn results in lower hydrogen embrittlement susceptibility.

The development of high strength steel enables constructions to be made with less material than with previous used steel grades. The possibility of creating lightweight constructions with the same or even better mechanical properties is of high focus in the steel industry today. This can reduce productional costs as well as transportation related costs and have a less negative environmental impact. As steels are developed to be more durable, the processing of these steels grow more challenging and the use of conventional welding methods such as MIG/MAG-welding prove difficult (impossible for some steel grades) to obtain acceptable quality with single pass welds. The interest and use of laser-arc hybrid welding has increased during the last decade for its high welding speed and deep weld penetration. There are however still areas of the process that are not well documented. In this master thesis project, joining of laser cut high strength steel sheets with laser-arc hybrid welding has been tested to evaluate weld quality and process stability. The tests was performed on threesteel grades with increasing strength (S960QL, S1100QL and S1300QL). Steel sheets with different pre-welding preparations has been laser-arc hybrid welded and a documentation displaying resulting differences in weld geometry, microstructure, process stability and hardness has been created. For example, samples welded withthe mill scale still present was found not to have negative impact in terms of weld geometry and hardness when using laser-arc hybrid welding. Cooling rates was collected to aid the evaluation of microstructural composition in the welded area. The results of the work in this thesis project can be of aid in making the joining process of high strength steels more efficient.

With the desire to lighten the frame while keeping or increasing the strength, Advanced High-Strength Steels (AHSS) have been developed for use in the automotive industry. AHSS meet many vehicle functional requirements because of their excellent strength and acceptable ductility. But joining AHSS is a challenge, because weldability is lower than that of mild steels. Friction stir spot welding (FSSW) is a solid state joining process that can provide a solution to the weldability issues in AHSS, but FSSW has not been studied in great detail for this application. In this work, Si3N4 tools were used for FSSW experiments on DP 980 steel with 1.2mm thickness. Joint strength was measured by lap shear tension testing, while thermocouples were used for the temperature measurements. A finite element model was developed in order to predict material flow and temperatures associated with FSSW. Since a 3D model of the process is very time consuming, a novel 2D model was developed for this study. An updated Lagrangian scheme was employed to predict the flow of sheet material, subjected to the boundary conditions of the fixed backing plate and descending rotating tool. Heat generation by friction was computed by including the rotational velocity component from the tool in the thermal boundary conditions. Material flow was calculated from a velocity field while an isotropic, viscoplastic Norton-Hoff law was used to compute the material flow stress as a function of temperature, strain and strain rate. Shear stress at the tool/sheet interface was computed using the viscoplastic friction law. The model predicted welding temperatures to within 4% of the experiments. The welding loads were significantly over predicted. Comparison with a 3D model of FSSW showed that frictional heating and the proportion of total heat generated by friction were similar. The position of the joint interface was reasonably well predicted compared to experiment.

No description available.

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, plunge speed, cutting and welding depths, and dwell times. It was determined that, when using 1.6 mm thick coupons, maximum joint strengths would be obtained at a 2.03 mm cutting depth, 3.30 mm welding depth, and 2500 RPM welding speed. At these levels, the weld is stronger than the magnesium alloy, resulting in failure in the AZ31 rather than in the FBJ joint in lap shear testing.

With the desire to improve passenger safety and fuel efficiency, Ultra High Strength Steels (UHSS) have been developed for use in the automotive industry. UHSS are high strength steels with high ductility and strength. DP 980 is one of these UHSS being applied in automobile manufacturing. DP 980 is difficult to join with Resistance Spot Welding (RSW) because of the high carbon content and alloying in this material. The weld becomes brittle when it solidifies during the welding process. With the desire and motivation of widely using UHSS, new welding processes are needed to be developed in order to effectively join DP 980. Friction Stir Spot Welding (FSSW) is a developing welding process aimed to replace RSW in the automotive industry because of its ability to join materials at a lower temperature. Currently the welding loads of the tools are higher than 2000 pounds, ranging from 3,000 to 5,000 pounds, which exceeds the limit of the welding robots in the automotive factories. It is proposed that the welding loads can be reduced by increasing the spindle speed of the FSSW tool. Other focuses in the research include increasing the life of the tool and developing acceptable welding parameters for High Speed FSSW. The experimental work done for this thesis provided support that weld strength can be obtained at levels above the acceptable standard for DP 980 material (greater than 2400 pound lap shear fracture load for 1.2 mm material) while keeping the vertical load on the welding machine spindle below 2000 lbs.

The intention of this thesis is to develop, evaluate new concepts and look over the current design for a container sized barge module. By request of Group Ocean, a cost and weight reduction is the main improvement criteria along with keeping the strength of the module.Five concepts are developed, analyzed and discussed with the supervisor at Group Ocean, where three are decided to be presented here. The other two are left out, since they are considered way too expensive without giving a satisfying result. The three concepts that are developed throughout this thesis are; changing to high strength steel, changing to sandwich panels and increasing stiffeners with smaller dimensions.A structural optimization is made in the software MATLAB to find out the best dimension to use for the sandwich panels. To determine the local stresses, the finite element method is used in Inventor Professional. It is also where the design and CAD modules are built in, so for simplifications it is used for FEA (Finite Element Analysis) as well. To reduce the amount of elements and nodes, shell elements and other structural constraints are used in the FEA. All the concepts are modelled with the same structural constraints so a practical comparison study can be made.The final designs resulted in a total weight reduction up to 40% with a material cost reduction of 12%. Based on what type of material is chosen, the material cost reduction range is between 3-12% and the weight reduction range is between 13-40%.

This paper presents the details of an experimental investigation on the behaviour of axially loaded concrete-filled stainless steel elliptical hollow sections. The experimental investigation was conducted using normal and high strength concrete of 30 and 100 MPa. The current study is based on stub column tests and is therefore limited to cross-section capacity. Based on the equations proposed by the authors on concrete-filled stainless steel circular columns, a new set of equations for the stainless steel concrete-filled elliptical hollow sections were proposed. From the limited data currently available, the equation provides an accurate and consistent prediction of the axial capacity of the composite concrete-filled stainless steel elliptical hollow sections.

This paper presents the behaviour and design of axially loaded concrete-filled steel tube circular stub columns. The study was conducted over a wide range of concrete cube strengths ranging from 30 to 110 MPa. The external diameter of the steel tube-to-plate thickness (D/t) ratio ranged from 15 to 80 covering compact steel tube sections. An accurate finite element model was developed to carry out the analysis. Accurate nonlinear material models for confined concrete and steel tubes were used. The column strengths and load¿axial shortening curves were evaluated. The results obtained from the finite element analysis were verified against experimental results. An extensive parametric study was conducted to investigate the effects of different concrete strengths and cross-section geometries on the strength and behaviour of concrete-filled compact steel tube circular stub columns. The column strengths predicted from the finite element analysis were compared with the design strengths calculated using the American, Australian and European specifications. Based on the results of the parametric study, it is found that the design strengths given by the American Specifications and Australian Standards are conservative, while those of the European Code are generally unconservative. Reliability analysis was performed to evaluate the current composite column design rules.

Friction Bit Joining (FBJ) is a new technology that can be used to join dissimilar materials together. This ability makes it a good candidate for creating lightweight structures for the automotive industry by combining lightweight materials such as aluminum to stronger materials like advanced high-strength steels. The automotive industry is putting significant effort into interest in reducing vehicle structure weight to increase fuel efficiency and reduce greenhouse gas emissions. Joining of dissimilar materials is a challenge they face in the light weighting the body of the vehicle. The purpose of the current research is to employ FBJ in the joining of a very challenging material combination: GA DP 1180 to AA 7085-T71. In accomplishing this purpose, the goal is to move FBJ toward a more production ready process by better understanding the effects of tooling, bit design, and process parameters on joint strength and reliability as they relate to load profiles captured during the joining process. It was found that the joint strength variation was influenced strongly by the hardness and the geometric consistency of the consumable bits. Bit hardness below 45 HRC led to joint strength that was less than the required specification (5kN in lap shear tension, and 1.5kN in cross-tension and T-peel). Variation in bit height and diameter also led to excessive scatter in joint strength values, where it was not possible to meet the standard for 10 consecutive specimens (for each of the three tests). Implementation of high-speed data acquisition (1000Hz) enabled the capture of load curve profiles generated during FBJ. Load curve profiles were correlated with destructive testing results to discover the impact of process parameter combinations. Analysis of load curve profiles led to improvements in parameter selections of spindle speeds (revolutions per minute) and spindle feed-rates (inches per minute). Process parameters of 5000 RPM and 15 IPM reduced variation in load-curve profiles and destructive testing. Satisfactory joint strength was achieved in lap shear tension, cross-tension, and T-peel testing configurations with values of 10.1 kN, 4.1 kN, and 1.8 kN, respectively. The presence of wet adhesive had little impact on joint performance. Finally, the analysis of a load-curve profiles resulted in a criterion that allowed for distinguishing "good" welds from "bad" ones, where a threshold load of 6kN, or higher, during the dwell phase of welding was required in order to meet joint strength standards.