No description available.

No description available.

The calculation of the loadbearing capacity of hollow section joints using the design formulas according to EN 1993-1-8 assumes full-strength welded connections if the non-linear stress distribution over the circumference is not covered by calculation. Sufficient ductility in the connections ensures a plastic redistribution capacity within each joint. In the case of hollow section structures made of high-strength steels, it becomes more difficult to meet the requirement for full-strength welds as the yield strength of the base material increases. This article begins with a summary of the current rules for the design and execution of welded hollow section joints. The softening behaviour of high-strength steels and the loadbearing capacity of welded connections with local softening in the HAZ are then discussed. That is followed by the presentation of the results from the AiF-FOSTA research project P1020 regarding the influence of manufacturing parameters on the properties of welded connections and the HAZ. The experimental test programme for single-sided welded T-connections and the parameter studies within the research project P1453 are also described. Finally, a design approach is presented to account for HAZ failure and hybrid failure modes of hollow section connections.

Die vorliegende Arbeit befaßt sich mit der experimentellen Analyse des Tragverhaltens von Hochleistungsbeton unter mehraxialer Beanspruchung. Dabei wurden sowohl die zwei und die dreiaxiale Drucktragfähigkeit als auch das Verhalten unter zweiaxialer kombinierter Druck Zug Beanspruchung untersucht. Für die Analyse kamen jeweils drei Betonfestigkeitsklassen zum Einsatz, C 55/67, C 70/85 und C 90/105. Innerhalb der durchgeführten Versuchsreihen wurden sowohl die jeweiligen Bruchlasten als auch die Spannungs Dehnungs Beziehungen ermittelt. Die Ergebnisse dieser Untersuchungen wurden mit denen verglichen, die an Normalbeton gewonnen wurden. Aus diesem Vergleich wurden Schlußfolgerungen für den Einsatz von Hochleistungsbetonen abgeleitet. Zur mathematischen Beschreibung des Tragverhaltens von Hochleistungsbeton wurden für die untersuchten Beanspruchungsregime Näherungsfunktionen angegeben. / The subject of this paper is the experimental analysis of the behavior of High Performance Concrete under multiaxial loading. Thereby the behavior under bi- and triaxial compression as well as the behavior under combined compression-tension stresses were examined. Three concrete grades were examined, C 55/67, C 70/85 and C 90/105. Within the test series, the ultimate loads and the stress-strain-relationships were determined. The results of the examinations were compared to the results which are already known for normal strength concrete. From these comparisons conclusions for the usage of high performance concrete were made. For the examined states of stress mathematical approximations are specified.

The autogenous shrinkage due to self-desiccation of high- and ultra-high performance concretes with very low water-cement ratio in case of restraint leads to considerable stresses starting from very early age. The resultant risk of cracking presently cannot be adequately investigated. Parameters that are particularly difficult to capture experimentally are the concrete temperature and the viscoelasticity. The primary objective of this work was to assess as precise as possible the autogenous shrinkage cracking propensity of representative concretes at strong restraint and constant room temperature. Test methods needed to be chosen and enhanced in a way that preferably allowed for the efficient and precise investigation of all relevant factors in the future. Ideally, a method suitable for a complete empirical modeling was provided. First the methodological requirements and the advantages and disadvantages of existing test methods were discussed. Based on this, optimized test methods were proposed. Their suitability was verified using the example of ultra-high strength concrete. The choice of concrete compositions considered the essential measures for reducing shrinkage (internal curing, shrinkage-reducing admixtures, reduction of the fraction of Portland cement in the binder). The autogenous shrinkage was measured with the shrinkage cone method. This new test method was validated by investigations of the repeatability and reproducibility and proved efficient and precise. It allows for measurements under non-isothermal conditions; no established test method exists for that purpose to date. The autogenous shrinkage of the ultra-high strength concretes at the age of 24 h, investigated under quasi-isothermal conditions (20 °C), was between 0,25 mm/m and 0,70 mm/m. It was particularly low when a shrinkage-reducing admixture was added and when superabsorbent polymers were used. The stresses due to restraint were determined with the restrained ring test. A large part of the stresses to be expected according to Hooke’s Law were eliminated by creep and relaxation. The relaxation capacity being very pronounced at very early age was the main reason that no visible cracking occurred, not even with the concretes with high autogenous shrinkage. The development of the autogenous shrinkage cracking propensity was described as ratio of restraint stress and splitting tensile strength. By means of modified ring tests, used to determine the maximum tensile stress, it could be shown that the ratio of stress to strength is an appropriate failure criterion. However, the cracking propensity can be calculated correctly only if the strongly age-dependent ratio of uniaxial to splitting tensile strength is accounted for. Besides, it needs to be considered that at very early age a plastic stress redistribution may occur in restrained ring tests. The reference concrete showed a high cracking propensity of up to 0.68. The fact that shrinkage-reducing measures led to significantly lower values reveals their relevance for the safe application of ultra-high strength concrete. However, the investigations carried out here at 20 °C do not allow for a final assessment of the cracking propensity under typical on-site conditions. To empirically model the autogenous shrinkage cracking propensity as a function of temperature and stress level in the future, an analytical stress solution for non-isothermal restrained ring tests and a new approach for investigating the residual stress and relaxation capacity by means of non-passive restrained ring tests was suggested. / Das durch Selbstaustrocknung verursachte autogene Schwinden von besonders leistungsfähigen Betonen mit sehr niedrigem Wasserzementwert führt bei Dehnungsbehinderung bereits in sehr frühem Alter zu erheblichen Zwangsspannungen. Die Gefahr der Rissbildung, die sich daraus ergibt, lässt sich bislang nur unzureichend untersuchen. Experimentell besonders schwer zu erfassende Faktoren sind die Betontemperatur und die Viskoelastizität. Das vorrangige Ziel der Arbeit war die möglichst genaue Ermittlung der autogenen Schwindrissneigung repräsentativer Betone bei starker Dehnungsbehinderung und konstanter Raumtemperatur. Dabei waren die Prüfverfahren möglichst so zu wählen und weiterzuentwickeln, dass sich zukünftig alle relevanten Faktoren effizient und genau untersuchen lassen. Im Idealfall sollte eine Methode entstehen, die eine vollständige empirische Modellierung erlaubt. Zunächst wurden die methodischen Anforderungen und die Vor- und Nachteile existierender Prüfverfahren diskutiert. Darauf aufbauend wurden optimierte Verfahren vorgeschlagen. Ihre Eignung wurde an ultrahochfestem Beton überprüft. Bei der Auswahl der Betone wurden die wesentlichen Maßnahmen zur Schwindreduzierung berücksichtigt (innere Nachbehandlung, schwindreduzierende Zusatzmittel, Verringerung des Portlandzementanteils am Bindemittel). Das autogene Schwinden wurde mit dem Schwindkegelverfahren gemessen. Das neue Verfahren wurde durch Untersuchungen zur Wiederhol- und Vergleichsgenauigkeit validiert und erwies sich als effizient und genau. Es ermöglicht Messungen unter nicht-isothermen Bedingungen; hierfür existiert bisher kein etabliertes Verfahren. Das autogene Schwinden der untersuchten ultrahochfesten Betone unter quasi-isothermen Bedingungen (20 °C) betrug im Alter von 24 h zwischen 0,25 mm/m und 0,70 mm/m. Besonders gering war es bei Zugabe eines schwindreduzierenden Zusatzmittels bzw. Verwendung superabsorbierender Polymere. Mit dem Ring-Test wurden die bei Dehnungsbehinderung entstehenden Spannungen ermittelt. Ein großer Teil der gemäß Hooke’schem Gesetz zu erwartenden Spannungen wurde durch Kriechen und Relaxation abgebaut. Die im sehr frühen Alter stark ausgeprägte Relaxationsfähigkeit war der wesentliche Grund dafür, dass es selbst bei Betonen mit hohem autogenen Schwinden zu keiner erkennbaren Rissbildung kam. Die Entwicklung der autogenen Schwindrissneigung wurde als Verhältnis von Zwangsspannung und Spaltzugfestigkeit beschrieben. Durch modifizierte Ring-Tests, mit deren Hilfe die maximale Zugspannung ermittelt wurde, konnte gezeigt werden, dass das Verhältnis von Spannung und Festigkeit als Versagenskriterium geeignet ist. Die Rissneigung lässt sich aber nur dann korrekt berechnen, wenn das stark altersabhängige Verhältnis von einaxialer Zugfestigkeit und Spaltzugfestigkeit berücksichtigt wird. Außerdem ist zu beachten, dass es im sehr frühen Alter zu einer plastischen Spannungsumlagerung in Ring-Tests kommen kann. Der Referenzbeton wies eine hohe Rissneigung von bis zu 0,68 auf. Dass die schwindreduzierenden Maßnahmen zu deutlich geringeren Werten führten, zeigt deren Bedeutung für den sicheren Einsatz von ultrahochfestem Beton. Die hier bei 20 °C durchgeführten Untersuchungen erlauben allerdings keine abschließende Bewertung der Rissneigung unter baustellentypischen Bedingungen. Um die autogene Schwindrissneigung zukünftig als Funktion der Temperatur und des Lastniveaus empirisch modellieren zu können, wurden eine analytische Spannungslösung für nicht-isotherme Ring-Tests und ein neuer Ansatz zur Untersuchung der Resttrag- und Relaxationsfähigkeit mit Hilfe nicht-passiver Ring-Tests vorgeschlagen.

Der derzeitige technische Fortschritt stützt sich maßgeblich auf die Nutzung von elektrischem Strom. Der Anteil der Stromerzeugung aus Sonnenlicht hat mittlerweile in Deutschland den der Wasserkraft überschritten, der 1990 noch der größte regenerative Energielieferant war. Die Technologie der Photovoltaik (PV) wandelt die hochenergetische Strahlung der Sonne in elektrischen Strom um und nutzt dabei häufig Glasplatten als tragende Struktur. Der Hauptanspruch dieser Arbeit liegt in der Entwicklung und Untersuchung eines Befestigungssystems mit einer höher- oder hochmoduligen Klebverbindung zum gläsernen PV-Modul sowie einer möglichst universell einsetzbaren Fügeverbindung zur Unterkonstrukion. Die systematische Enwicklung der Fügeverbindung zum PV-Modul basiert auf dem Ansatz eines flexiblen, stützenden \\hbox{Ringes} für das Fügeelement (Halter), um die durch eine mechanische Belastung der Module induzierten Zugspannungen im Glas über der Fügeelementkante zu reduzieren. Eine neuartige, kombinierte Klammer-Keil-Verbindung sichert die Befestigung auf einer von ihr unabhängigen Unterkonstruktion sowohl quer als auch längs zur Schienenrichtung. Experimentelle Arbeiten charakterisieren die eingesetzte Klebverbindung unter verschiedenen Beanspruchungsszenarien, um sowohl konstruktions- als auch klebstoffbedingte Möglichkeiten und Grenzen der Fügeverbindung für die vorliegende Anwendung zu identifizieren. Die Untersuchungen weisen zudem geeignete Vorbehandlungsmaßnahmen der Aluminiumoberflächen aus. Sowohl numerische Simulationen als auch die neuartig eingesetzte Nahbereichsphotogrammetrie bestätigen in Bauteiluntersuchungen die vorteilige Wirkung des flexiblen, höhermodulig geklebten Ringes. Die vorliegende Arbeit setzt sich hierbei auch kritisch mit unterschiedlichen Einflüssen auf die Ergebnisse auseinander, die einerseits durch verschiedene Prüfstände hervorgerufen werden können und andererseits auch den verwendeten Methoden zugrunde liegen. / Today much of technical advances are due to the usage of electricity. The contribution of solar power to the production of electricity in Germany currently surpasses water powered electricity which was in 1990 the almost exclusive renewable energy source. The technology of photovoltaic systems based on high-powered sun radiation, often utilizes glass plates as a supporting structure. This dissertation primarily focuses on the research and development of a mounting system with a higher or high modulus adhesively bonded joint to the PV-module as well as an all-purpose connection to the substructure. The systematical development process of the connection to the PV-module is based on the approach of a flexible supporting ring-shaped mounting element. This reduces the tension within the glass surface at the edge of the mounting element when mechanically loading the PV-module. A novel connection using a clamp-wedge combination ensures the ability to mount the PV-module horizontally or vertically to the rail substructure. Through the development process, the bonded joint is exposed to various scenarios where the construction as well as the adhesive possibilities and limitations under each scenario are analyzed. Research outcomes yield recommendations for appropriate pre-treatment of the aluminum surfaces. Numerical simulations as well as the novel use of the near-field photogrammetry method confirmed beneficial action of the flexible ring-shaped mounting element within assembly testing of large glass specimens. This dissertation discusses how different variables can have a considerable effect on results when introduced through the testing device and through monitoring methods.

The importance of fire safety design has been realised due to the ever increasing loss of properties and lives caused by structural failures during fires. In recognition of the importance of fire safety design, extensive research has been undertaken in the field of fire safety of buildings and structures especially over the last couple of decades. In the same period, the development of fire safety engineering principles has brought significant reduction to the cost of fire protection. However the past fire research on steel structures has been limited to heavier, hot-rolled structural steel members and thus the structural behaviour of light gauge cold-formed steel members under fire conditions is not well understood. Since cold-formed steel structures have been commonly used for numerous applications and their use has increased rapidly in the last decade, the fire safety of cold-formed steel structural members has become an important issue. The current design standards for steel structures have simply included a list of reduction factors for the yield strength and elasticity modulus of hot-rolled steels without any detailed design procedures. It is not known whether these reduction factors are applicable to the commonly used thin, high strength steels in Australia. Further, the local buckling effects dominate the structural behaviour of light gauge cold-formed steel members. Therefore an extensive research program was undertaken at the Queensland University of Technology to investigate the local buckling behaviour of light gauge cold-formed steel compression members under simulated fire conditions. The first phase of this research program included 189 tensile coupon tests including three steel grades and six thicknesses to obtain the accurate yield strength and elasticity modulus values at elevated temperatures because the deterioration of the mechanical properties is the major parameter in the structural design under fire conditions. The results obtained from the tensile tests were used to predict the ultimate strength of cold-formed steel members. An appropriate stress-strain model was also developed by considering the inelastic mechanical characteristics. The second phase of this research was based on a series of more than 120 laboratory experiments and corresponding numerical analyses on cold-formed steel compression members to investigate the local bucking behaviour of the unstiffened flange elements, stiffened web elements and stiffened web and flange elements at elevated temperatures up to 800°C. The conventional effective design rules were first simply modified considering the reduced mechanical properties obtained from the tensile coupon tests and their adequacy was studied using the experimental and numerical results. It was found that the simply modified effective width design rules were adequate for low strength steel members and yet was not adequate for high strength cold-formed steel members due to the severe reduction of the ultimate strength in the post buckling strength range and the severe reduction ratio of the elasticity modulus to the yield strength at elevated temperatures. Due to the inadequacy of the current design rules, the theoretical, semi-empirical and empirical effective width design rules were developed to accurately predict the ultimate strength of cold-formed steel compression members subject to local buckling effects at elevated temperatures. The accuracy of these new design methods was verified by comparing their predictions with a variety of experimental and numerical results. This thesis presents the details of extensive experimental and numerical studies undertaken in this research program and the results including comparison with simply modified effective width design rules. It also describes the advanced finite element models of cold-formed steel compression members developed in this research including the appropriate mechanical properties, initial imperfections, residual stresses and other significant factors. Finally, it presents the details of the new design methods proposed for the cold-formed steel compression members subject to local buckling effects at elevated temperatures.

More complex and bigger structures have increased the applicability of low alloy high strength steels due to weight and cost reductions in these projects. One of the requirements for the use of these materials is the preservation of performance after welding. Meanwhile, the norms on which the Welding Procedures Specifications (WPS) are based have not yet considered the development of modern steel and its new production process, resulting in unnecessary welding costs that diminish the profits of the application of this type of steel. This thesis aimed to develop and evaluate an experimental methodology to guide the creation and control of welding procedures for structural steel through a microstructural atlas of the heat affected zone (HAZ) in a thermomechanical control process (TMCP), 65 ksi steel (ASTM A572 Grade 65). This steel was used in the project of an industrial building for CBMM in Araxá, Minas Gerais, Brazil. It is proposed that through a microstructural atlas of a given steel, it is possible to determine the range of cooling rates that the steel may suffer during welding without affecting mechanical properties and without risking cold cracks. When comparing the microstructure of steel welds performed in field conditions, it is possible to determine the heat input range for a given process in the preparation of a WPS. The selected case study is from a high strength low alloy class 65 ksi steel (ASTM A572 Grade 65) that was used in the structure of an industrial building. The steel was produced using TMCP. The atlas was created via the construction of a continuous cooling transformation diagram using physical simulation (dilatometer and Gleeble) of the coarse grain HAZ (GCHAZ). The characterization of the simulated region was performed by metallography and mechanical tests. The microstructure of real welds made by a qualified WPS were compared to the atlas in order to certify the correct use of parameters and to validate the method. The methodology was also qualified and the potential economic benefits were quantified (based only on the reduction of consumables used and the increased availability of the welding process machine) for the selected industrial project. The mapped microstructures varied from martensite (at high cooling rates) to pearlite/ferrite with large grain size (at low cooling rates). There was remarkable prevalence of bainitic microstructure in a wide range of cooling rates, consistent with the chemical composition of the steel studied. Comparisons with real weld microstructures showed the atlas is compatible with them, and that it can more accurately describe the effective thermal cycle xi that occurs in the coarse grain region of the HAZ (other regions were not included). The application of this methodology in the development of new WPS would allow greater flexibility in the welding procedures, including welding without preheating. In this respect alone, it was possible to forecast savings of approximately R$200,000.00, 1,000 hours of processing and 172 tonnes of carbon equivalent emissions. / Estruturas cada vez mais complexas e de maiores dimensões vêm aumentando a aplicabilidade de aços de baixa liga e alta resistência, devido à redução de peso e custo dessas estruturas. Um dos requisitos para o uso desses materiais é a manutenção do desempenho após soldagem. Entretanto, as normas em que se baseiam as Especificações de Procedimentos de Soldagem (EPS) ainda não consideram aços mais modernos em termos de rota de fabricação, o que pode fazer com que custos desnecessários de soldagem minimizem os ganhos da aplicação desses aços. Este trabalho teve como objetivo o desenvolvimento e avaliação de uma metodologia para, experimentalmente, orientar a elaboração e o controle da aplicação de procedimentos de soldagem para aços estruturais, através de atlas microestrutural de regiões da zona afetada pelo calor (ZAC). Propõe-se que, através de um atlas microestrutural de um dado aço, seja possível determinar a faixa otimizada de energia de soldagem para um dado processo na elaboração e aplicação da EPS e, consequentemente, as velocidades de resfriamento que o aço possa sofrer durante a soldagem, sem perder as propriedades mecânicas e sem colocálo em risco quanto a trincas a frio. Tomou-se como estudo de caso o aço produzido por laminação controlada de classe de resistência de 65 ksi (ASTM A572 Grau 65), utilizado em um projeto de um prédio industrial na empresa CBMM. Trata-se de um aço fabricado pelo processo TMCP com resfriamento acelerado. A elaboração do Atlas se deu através da construção de um diagrama CCT, por simulação física (dilatômetro e Gleeble), da região de grãos grosseiros da zona afetada pelo calor (ZAC GG). Foram feitas caracterizações metalográficas e mecânicas das regiões simuladas. Microestruturas de soldas realizadas com EPS qualificadas foram comparadas com as do Atlas para se certificar da adequabilidade dos parâmetros utilizados e validação da abordagem. Foram realizadas ainda a qualificação e quantificação de potenciais benefícios econômicos no citado projeto industrial, obtidos pelo uso desta metodologia. As microestruturas apresentadas no mapa variavam de martensíta, para altas taxas de resfriamento, até perlita/ferrita de tamanho de grão elevado, para baixas taxas de resfriamento. Observou-se notável predominância da microestrutura bainítica em uma larga faixa de taxas de resfriamento, compatível com as propriedades e composição do aço estudado (alta soldabilidade). As comparações com as microestruturas de soldas reais mostraram que o Atlas pode descrever de forma precisa o ciclo térmico efetivamente imposto ix na ZAC GG. Concluiu-se que a aplicação desta metodologia na elaboração de novas EPS permitiria uma maior flexibilidade nos procedimentos de soldagem, admitindo inclusive soldagem sem pré-aquecimento. Em relação a não necessidade de pré-aquecimento, podese prever uma economia significante de custos e redução de emissão de gases que provocam efeito estufa. / Mestre em Engenharia Mecânica

Various anchorage systems including both cast-in-place and post-installed anchors have been developed for fastening both non-structural and structural components to concrete structures. The need for increased flexibility in the design of new structures and strengthening of existing concrete structures has led to increased use of various metallic anchors in practice. Although millions of fasteners are used each year in the construction industry around the world, knowledge of the fastening technology remains poor. In a sustainable society, buildings and structures must, from time to time, be adjusted to meet new demands. Loads on structures must, in general, be increased to comply with new demands, and the structural components and the structural connections must also be upgraded. From the structural connection point of view, the adequacy of the current fastenings for the intended increased load must be determined, and inadequate fastenings must either be replaced or upgraded. The current design models are generally believed to be conservative, although the extent of this behavior is not very clear. To address these issues, the current models must be refined to allow the design of new fastenings and also the assessment of current anchorage systems in practice. The research presented in this thesis consists of numerical and experimental studies of the load-carrying capacity of anchors in concrete structures. Two different types of anchors were studied: (I) cast-in-place headed anchors, and (II) post-installed adhesive anchors. This research focused particularly on the tensile load-carrying capacity of cast-in-place headed anchors and also on the sustained tension loading performance of post-installed adhesive anchors. The overall objective of this research was to provide knowledge for the development of improved methods of designing new fastening systems and assessing the current anchorage systems in practice. For the cast-in-place headed anchors (I), the influence of various parameters including the size of anchor head, thickness of concrete member, amount of orthogonal surface reinforcement, presence of concrete cracks, concrete compressive strength, and addition of steel fibers to concrete were studied. Among these parameters, the influence of the anchor head size, member thickness, surface reinforcement, and cracked concrete was initially evaluated via numerical analysis of headed anchors at various embedment depths. Although these parameters have considerable influence on the anchorage capacity and performance, this influence is not explicitly considered by the current design models. The numerical results showed that the tensile breakout capacity of headed anchors increases with increasing member thickness and/or increasing size of the anchor head or the use of orthogonal surface reinforcement. However, their capacity decreased considerably in cracked concrete. Based on the numerical results, the current theoretical model for the tensile breakout capacity of headed anchors was extended by incorporating several modification factors that take the influence of the investigated parameters into account. In addition, a supplementary experimental study was performed to verify the numerically obtained findings and the proposed refined model. The experimental results corresponded closely to the numerical results, both in terms of failure load and failure pattern, thereby confirming the validity of the proposed model. The validity of the model was further confirmed through experimental results reported in the literature. Additional experiments were performed to determine the influence of the concrete compressive strength and the addition of steel fiber to concrete on the anchorage capacity and performance. These experiments showed that the anchorage capacity and stiffness increase considerably with increasing concrete compressive strength, but the ductility of the anchor decreases. However, the anchorage capacity and ductility increased significantly with the addition of steel fibers to the concrete mixture. The test results also revealed that the tensile breakout capacity of headed anchors in steel fiber-reinforced concrete is significantly underestimated by the current design model. The long-term performance and creep behavior of the post-installed headed anchors (II) was evaluated from the results of long-time tests on adhesive anchors under sustained loads. In this experimental study, adhesive anchors of various sizes were subjected to various sustained load levels for up to 28 years. The anchors were also exposed to several in-service conditions including indoor temperature, variations in the outdoor temperature and humidity, wetness (i.e., water on the surface of concrete), and the presence of salt (setting accelerant) additives in the concrete. Among the tested in-service conditions, variations in the outdoor temperature and humidity had the most adverse effect on the long-term sustained loading performance of the anchors. Based on the test results, recommendations were proposed for maximum sustained load levels under various conditions. The anchors tested under indoor conditions could carry sustained loads of up to 47% of their mean ultimate short-term capacities. However, compared with these anchors, the anchors tested under outdoor conditions exhibited larger creep deformation and failure occurred at sustained loads higher than 23% of their mean ultimate short-term capacities. Salt additives in concrete and wet conditions had negligible influence on the long-term performance of the anchors, although the wet condition resulted in progressive corrosion of the steel. Based on the experimental results, the suitability of the current testing and approval provisions for qualifying adhesive anchors subjected to long-term sustained tensile loads was evaluated. The evaluations revealed that the current approval provisions are not necessarily reliable for qualifying adhesive anchors for long-term sustained loading applications. Recommendations were given for modifying the current provisions to ensure safe long-term performance of adhesive anchors under sustained loads.

Actuellement, l’industrie automobile est à la recherche d’une meilleure solution pour l’allégement de la structure de véhicule afin de diminuer la consommation de carburant et par conséquent diminuer les émissions nocives de CO2. Les aciers à très haute résistance (THR) mécanique permettent d’obtenir les tôles d’acier à section diminué avec les mêmes ou meilleurs propriétés fonctionnels. Les aciers Dual-Phase (DP), constitués majoritairement d’une phase ductile, la ferrite, et d’une phase dure, la martensite, occupent une place importante en tant que matériaux de structure destinés au challenge préoccupant l’industrie automobile. Une bonne résistance à l’endommagement est exigée pour leur utilisation en tant que des pièces de structures et de renfort pour l’automobile. Il a été bien établi que la résistance à l’endommagement des ces aciers Dual-Phase est contrôlée par leur microstructure. Ce travail de thèse s’est inscrit dans une logique de compréhension des mécanismes d’endommagement d’un acier Dual-Phase modèle, le DP 780, en fonction de différents paramètres microstructuraux. Deux mécanismes d’endommagement ont été identifiés pour l’acier DP 780 : la décohésion de l’interface ferrite/martensite et la formation de cavités autour des carbures, dans la martensite revenue. Un modèle qualitatif de mécanisme d’endommagement a été développé afin de pouvoir prédire l’endommagement de l’acier DP 780. Ce modèle qualitatif, développé pour l’acier DP 780, servira de base d’approfondissement de modèles plus élaborés et quantitatifs permettant la compréhension et la prédiction de l’endommagement des aciers Dual-Phase, de façon générale / In the automotive industry current environmental concerns require that the vehicle fuel consumption and CO2 emissions should be reduced as much as possible. It is therefore advantageous to reduce the weight of body in white components by replacing existing parts with higher strength, thinner gauge alternatives with equivalent or improved functional properties. Dual Phase (DP) steels are a class of high-strength low-alloy steels characterized by a microstructure consisting of martensite and ferrite. Dual Phase steels combine high strength levels with good ductility. Thus, DP steels are potentially very attractive for the automobile industry. In addition to the required high strength and ductility, DP steel has to be cold formed into complex shapes. It appears that DP steel damage behaviour is very complex and cannot be predicted using existing models based on standard mechanical properties. This work is concerned with the study of microstructural evolution and investigation of the relation between the microstructure and damage mechanisms in a reference DP 780 steel. Two damage mechanisms have been identified in this DP steel: ferrite/martensite interface decohesion and void formation at tempered carbides. A simple modeling for qualitative description of the observed damage formation mechanisms is proposed. This modeling permits a basic understanding of the experimentally observed trends and could be used as the starting point for a more detailed analysis in future