Spelling suggestions: "subject:"highspeed steel"" "subject:"highspeed ateel""
21 |
Desgaste e fadiga térmica de ligas \'aço matriz + NbC\'. / Wear and thermal fatigue of \'matrix steel + NbC\' alloys.Paula Fernanda da Silva 10 November 2006 (has links)
Utilizou-se o conceito de ?aço matriz + NbC? para produzir ligas com a matriz do aço rápido M2 ( 0,5%C ? 2%W ? 3%Mo ? 4,6%Cr ? 1%V) e variadas frações volumétricas de carbonetos de nióbio. Adicionou-se 2,5 e 5% de nióbio e carbono estequiométrico para a obtenção de carbonetos NbC e titânio (0,1%) para modificação da morfologia dos carbonetos NbC. Os carbonetos NbC apresentaram-se como carbonetos eutéticos com morfologia de escrita chinesa, como carbonetos primários com a morfologia de cruz de malta e como carbonetos eutéticos e primários com morfologia poligonal, estes últimos modificados com a adição de titânio. Após tratamento térmico de têmpera e revenimento para obtenção da máxima dureza, as ligas foram submetidas a ensaios de fadiga térmica (100 ciclos, 650ºC), de abrasão (roda de borracha ? 130N, 200rpm, 30min, hematita como abrasivo) e de deslizamento alternado (disco contra esfera ? 70,6N, amplitude: 6mm, freqüência, 6 Hz, 2h) para estudar o efeito da fração volumétrica e da morfologia dos carbonetos frente a estas solicitações. As ligas com carbonetos com morfologia poligonal e menor fração volumétrica de carbonetos (comparando-se morfologias iguais) apresentaram o melhor desempenho sob fadiga térmica devido ao baixo valor do parâmetro C/Dm da microestrutura (continuidade de carbonetos/distância livre média entre carbonetos). Os corpos-de-prova foram caracterizados por meio de microscopia ótica e eletrônica de varredura para determinar os sítios de nucleação e caminhos de propagação das trincas. Nos ensaios em roda de borracha as ligas com carbonetos eutéticos divorciados com morfologia poligonal apresentaram maior resistência ao desgaste do que os aços contendo carbonetos eutéticos cooperativos. O aumento da fração volumétrica de carbonetos NbC teve um máximo na resistência a abrasão e depois uma queda devido a presença de carbonetos primários grosseiros que fraturaram na superfície ensaiada e foram arrancados aumentanto a perda de massa. Nos ensaios de deslizamento alternado não foi possível hierarquizar o comportamento das ligas. Os corpos-de-prova de abrasão e de deslizamento foram caracterizados por microscopia ótica e eletrônica de varredura para determinar os mecanismos de desgaste atuantes. Um aço rápido para cilindros de laminação a quente (2%C ? 5%Cr ? 5%Mo ? 5%V) foi ensaiado sob condições idênticas às aplicadas às ligas estudadas, objetivando comparar desempenhos. O aço rápido apresentou desempenho superior nos ensaios de abrasão e de deslizamento alternado (devido a alta fração volumétrica de carbonetos eutéticos) e inferior no ensaio de fadiga térmica (devido ao alto parâmetro C/Dm da microestrutura oriundo da alta fração volumétrica de carbonetos eutéticos). / The concept of ?matrix steel + NbC? was used to cast alloys with the M2 steel matrix (0,5%C ? 2%W ? 3%Mo ? 4,6%Cr ? 1%V) and different volume fractions of niobium carbides. Niobium (2,5 e 5%) and stoichiometric carbon were added to produce NbC carbides and titanium (0,1%) to modify de NbC carbides morphology. NbC presented three basic morphologies: Chinese script (coupled eutectic); primary carbides with cross morphology and polygonal primary and eutectic carbides (divorced eutectics). After heat treatment of quench and temper in order to obtain the maximum hardness, the alloys were submitted to thermal fatigue test (100 cycles, 650ºC), dry rubber wheel abrasive wear test (130N, 200rpm, 30min, hematite as abrasive) and reciprocating sliding wear test (70,6N, amplitude: 6mm, frequency: 6Hz, 2h). The alloys with polygonal NbC carbides and lower volume fractions of carbides (for the same morphology) showed the best behaviour due to their low ?carbide continuity/carbide free path? ratio of the microstructure. The alloys were characterized by optical microscopy and SEM to investigate de cracks nucleation and propagation. In the dry rubber wheel tests, polygonal NbC eutectic carbides (divorced eutectics) showed better behaviour than Chinese script NbC eutectic carbides. High volume fractions of NbC carbides improved the abrasion resistance until a maximum and after that, the presence of big primary NbC carbides, lowered the abrasion resistance due to cracks in those big carbides. The results of the reciprocating sliding tests have not allowed to rank the performance of the alloys. Abrasion and sliding specimens were submitted to optical microscopy and SEM in order to evaluate the prevalent wear mechanisms. One high speed steel for hot rolling mill rolls (2%C ? 5%Cr ? 5%Mo ? 5%V) was tested under the same conditions that the alloys studied were tested in order to compare their performances. The high speed steel showed better performance in abrasion and reciprocating sliding wear due to the high volume fraction of coupled eutectic carbides and lower performance in thermal fatigue due to the high ?carbide continuity/carbide free path? ratio of the microstructure than the alloys studied.
|
22 |
Analýza řezání tenkostěnných součástí pilou / On the analysis of thin-wall parts sawingSpáčil, Radek January 2018 (has links)
Master‘s thesis deals with sawing of the thin-walled parts with high speed steel slitting saw. At first the most used conventional and unconventional possibilities of materiál cutting are described by a form of search. The next chapter describes forces arising from splitting saw machining, including their dependence on a specific cutting force, a chip cross section and a engagement angle. The second part of the thesis deals with the technological improvement of the cutting process, where three possible solutions are considered – geometry of the cutting tool, PVD coating deposition of the cutting tool and process fluid change. In the experimental part non coated slitting saw with burrs, non coated deburred slitting saw and coated slitting saws are compared. Used coatings were Ti(C,N), Cr-Al-Si-N, Al-Cr-B-N, and TripleCoating Cr, which is consisting of three layers TiN + (Al,Ti)N + Cr-Al-Si-N. The experiment has shown that the cutting forces inceases as the edge radius and wear level of the cutting tool increases. Coated cuttung tools has shown lower differences between the first and the last cut. Slitting saws have been also used in real cutting process to verify experimental results.
|
23 |
Evolution of artificial defects during shape rollingMirjana, Filipovic January 2007 (has links)
Very often defects are present in rolled products. For wire rods, defects are very deleterious since the wire rods are generally used directly in various applications. For this reason, the market nowadays requires wire rods to be completely defect-free. Any wire with defects must be rejected as scrap which is very costly for the production mill. Thus, it is very important to study the formation and evolution of defects during wire rod rolling in order to better understand and minimize the problem, at the same time improving quality of the wire rods and reducing production costs. The present work is focused on the evolution of artificial defects during rolling. Longitudinal surface defects are studied during shape rolling of an AISI M2 high speed steel and a longitudinal central inner defect is studied in an AISI 304L austenitic stainless steel during ultra-high-speed wire rod rolling. Experimental studies are carried out by rolling short rods prepared with arteficial defects. The evolution of the defects is characterised and compared to numerical analyses. The comparison shows that surface defects generally reduce quicker in the experiments than predicted by the simulations whereas a good agreement is generally obtained for the central defect.
|
24 |
Frézování axiálních drážek v rotoru turbíny / Milling of axial groove in rotary turbineKáčer, Pavel January 2008 (has links)
The aim of this work is comparison of special form tools for manufacture of grooves in rotor turbine. For this purpose tools are chosen from „A“ and „B“ company. Form milling cutters are confronted both in terms of their characteristic features, manufacturing methods, and time and economy intensity. Furthermore, there is described a possible future way of grooves‘ production through the use of the „C“ ‘s programme. Apart from that, this thesis also involves simple programme for comparing the chosen parameters.
|
25 |
Nové frézovací nástroje z rychlořezné ocelí pro hrubovací operace / New Milling HSS Cutters for Roughing OperationsJaroš, Aleš January 2015 (has links)
Dissertation thesis is focused on development, design and production of the new milling cutter which is used for roughing operations. High-speed steels, coating technology and milling technology are described in first chapters of dissertation thesis. The main part of this thesis is the design of the new milling cutter that has been designed on the basis of the machining simulation. The milling cutter is designed as a three-flute cylindrical end mill made of high speed steel. The each flute is composed of two special compensation edges. The compensation edges are used for reducing (at best suppression) tensile stress in the heel of the tooth. The milling cutter was made by lost wax technology, followed by grinding and thermal treatment. New designed tools were deposited by PVD coatings (e.g. (Al,Ti)N). Standard catalog milling cutters (producer ZPS - milling tools, Zlín, Czech Republic) were used for comparison the designed milling cutter. Carbon steel CSN 41 2050 (DIN 1.1191) was used for milling, which was carried out with using process liquid. The monitored parameters were force loading, flank wear and tensile stress during milling. The dynamometer Kistler was used for measuring force loading and data obtained during machining was used for stress analysis.
|
26 |
Evolution of artificial defects during shape rollingFilipovic, Mirjana January 2007 (has links)
Very often defects are present in rolled products. For wire rods, defects are very deleterious since the wire rods are generally used directly in various applications. For this reason, the market nowadays requires wire rods to be completely defect-free. Any wire with defects must be rejected as scrap which is very costly for the production mill. Thus, it is very important to study the formation and evolution of defects during wire rod rolling in order to better understand and minimize the problem, at the same time improving quality of the wire rods and reducing production costs. The present work is focused on the evolution of artificial defects during rolling. Longitudinal surface defects are studied during shape rolling of an AISI M2 high speed steel and a longitudinal central inner defect is studied in an AISI 304L austenitic stainless steel during ultra-high-speed wire rod rolling. Experimental studies are carried out by rolling short rods prepared with arteficial defects. The evolution of the defects is characterised and compared to numerical analyses. The comparison shows that surface defects generally reduce quicker in the experiments than predicted by the simulations whereas a good agreement is generally obtained for the central defect. / QC 20101105
|
27 |
Investigation of ASTM E 238 Bearing Pin Properties for Various Aerospace AlloysLee, Trevor J 01 January 2013 (has links) (PDF)
Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.
Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that plate material, fastener used, fastener lubrication, and plate hole preparation method (whether drilled and reamed or just drilled) have on the three bearing joint properties. The plate materials used were Al 7050 – T7451, Ti – 6Al – 4V (mill annealed), and PH13 – 8Mo – H1000. The fasteners were Ti – 6Al – 4V screws, coated A286 screws, and high speed steel (HSS) pins used as a control. Lubrication was tested using a corrosion inhibitor, PR – 1776M B – 2 from PRC – DeSoto, on the fastener or leaving the fastener uncoated. The HSS pins were always tested in the uncoated condition. 54 runs were performed, as outlined by a D-optimal design of experiment.
It was discovered from the statistical analysis of the results via ANOVA that both the plate material used and the pin material, whether a screw or a pin, had a significant effect on the bearing strength, bearing yield strength, and bearing stiffness. The interaction between the two factors was also significant on all responses but the bearing stiffness. PH13 – 8Mo – H1000 plates seemed to perform best on average, followed by Ti – 6Al – 4V plates, then Al 7050 – T7451 plates. PH13 – 8Mo – H1000 and Ti – 6Al – 4V plates had similar bearing strength and bearing yield strength averages with the HSS control pins being used, which had the highest mean values for a given plate and fastener. The Ti – 6Al – 4V and A286 screws behaved and performed statistically similar in most cases, except when hole preparation method was take into account. The Ti – 6Al – 4V screws performed better when the hole was drilled and reamed, while the coated A286 screws performed better when the hole was drilled only. All screws had lower resulting bearing properties than the HSS control pins.
It was also found that ASTM specification E238 – 84(08) is a precise test method, since the method could be performed repeatably and reliably with no missing data points. Therefore, this ASTM testing method is reasonable for determining bearing properties, which can then be used to design aircraft.
|
28 |
Estudo da tenacidade à fratura do aço rápido M2 fundido, modificado e tratado termicamente. / Fracture toughness of as-cast high speed steel M2, modified and heat treated.Silva, Wanderson Santana da 05 November 2001 (has links)
Neste trabalho foi medida a tenacidade à fratura de quatro ligas fundidas com composição química base do aço AISI M2 uma de composição química convencional (liga I), e as demais modificadas por adições de nitrogênio (liga II), cério (liga III) e antimônio (liga IV) submetidas a tratamentos térmicos visando a decomposição do carboneto M2C, a esferoidização e engrossamento dos carbonetos produto M6C e MC, em altas temperaturas e por diversos tempos. A metodologia empregada nesta avaliação da tenacidade à fratura foi a dos corpos de prova curtos com entalhe chevron segundo ASTM E 1304-97, de forma a superar a necessidade do pré-trincamento por fadiga, procedimento de difícil controle e custoso em materiais como os aços rápidos temperados e revenidos. Verificou-se que a metodologia utilizada para obtenção e ensaio de corpos de prova chevron foi de fácil execução (comparada à metodologia convencional) permitindo grande número de experimentos. Para verificar a consistência dos resultados, em algumas condições, também se utilizou a metodologia convencional segundo a ASTM E 399-90, cujo pré-trincamento foi feito utilizando os procedimentos propostos por Harris e Dunegan. Os resultados obtidos para os aços fundidos foram correlacionados com os obtidos para outros aços rápidos convencionais (VM2, M2 Thyssen) e um aço rápido sinterizado (SINTER 23). A microestrutura foi caracterizada utilizando-se técnicas de ataques metalográficos diferenciais, metalografia quantitativa manual e computadorizada e microscopia eletrônica de varredura. A avaliação microestrutural indica que não ocorreu precipitação eutética do carboneto M6C, em nenhuma das ligas fundidas. O carboneto M2C apresenta morfologia tanto irregular (plaquetas tipo 1) quanto regular-complexa (lamelas tipo 2). As ligas I, III e IV, apresentaram a predominância da morfologia tipo 1 enquanto que a liga II modificada pelo nitrogênio, apresentou apenas a morfologia tipo 2. O carboneto MC apresentou-se com morfologia regular-complexa. Medidas do espaçamento interdendrítico indicam que não houve influência significativa dos elementos modificadores sobre este parâmetro. Ensaios de resistência à flexão, indicam pouca influência dos elementos modificadores, mas forte influência dos tratamentos térmicos sobre o limite de resistência à ruptura transversal do aço fundido. Em todas as ligas, a resistência à flexão cresceu com o tempo de tratamento a 1200°C, bem como com a temperatura de decomposição em tratamentos por 2 horas. Análise das fraturas por microscopia eletrônica de varredura indicou que o crescimento das trincas se deu na região interdendrítica. O aço convencional apresentou resistência à ruptura transversal muito superior à dos aços fundidos. Os ensaios de tenacidade à fratura apresentaram resultados compatíveis com a literatura para os aços AISI M2 convencional e SINTER 23. Os resultados obtidos para o aço fundido, indicam queda nos valores de tenacidade à fratura nos materiais tratados a 1050°C com o avanço do tempo de tratamento; pouca variação dos valores com o tempo nas amostras tratadas a 1150°C; e aumento significativo da tenacidade à fratura com o tempo de tratamento a 1200°C. Os valores de tenacidade obtidos para os aços rápidos fundidos foram mais elevados que os obtidos para os materiais trabalhados e para o material sinterizado. / Fracture Toughness of four cast alloys with chemical composition based on the High-Speed Steel AISI M2 were measured. One of the alloys (alloy I) had the conventional AISI M2 composition, while the other three were modified by the addition of N (alloy II), Ce (alloy III) and Sb (alloy IV). The cast alloys were heat-treated in order to promote the decomposition of the M2C carbide as well as spheroidize and coarsen the product M6C e MC carbides. The method chosen for measuring fracture toughness was based on the use of short rod and bar chevron notched samples, according to ASTM E1304 97, in order to evade the need for fatigue pre-cracking, notoriously difficult for High Speed Steels quenched and tempered. The chevron-notch method proved straightforward and allowed for successful testing a great number of specimens. Conventional compact sample fracture toughness, according to ASTM E 399-90, with pre-cracking obtained using Harris-Dunegan drop-weight procedure, was used to validate the results. The results for cast alloys were compared with conventionally produced High Speed Steels (VM2, M2 Thyssen) and with a powder metallurgy High Speed Steel (SINTER 23). Microstructural characterization was performed using selective etching of polished surfaces, manual and automated quantitative metallography and SEM. Microstructural evaluation of as-cast alloys showed that there was no eutectic precipitation of M6C carbides. The M2C carbides show an irregular eutectic morphology (Type 1- plates) as well as a regular-complex eutectic morphology. Measurements of interdendritic spacing did not detect any effect of the modification. The bending test rupture strengths did not vary with the addition of modifying elements, but increased with the time and temperature of decomposition, spheroidization and coarsening of carbides. Rupture strengths increased with the heat-treatment time at 1200°C as well as with increasing temperatures for 2 h heat-treatments. SEM examination of the fracture surfaces showed that crack preferential growth path was interdendritical. Conventional High Speed Steels tested in bending presented better results for the rupture strength than cast steels. Fracture toughness results for M2 conventional steels and for the SINTER 23 steel were similar to the results from the literature. Fracture toughness results obtained for cast steels diminished with increasing decomposition time at 1050°C, did not change much with increasing decomposition time at 1150°C, increased markedly withy increasing decomposition times at 1200°C. The fracture toughness results for the as-cast steels were higher than the results obtained for the wrought steels and for the powder metallurgy steel.
|
29 |
"PROCESSAMENTO, USINAGEM E DESGASTE DE LIGAS SINTERIZADAS PARA APLICAÇÕES AUTOMOTIVAS" / "OBTENTION, MACHINING AND WEAR OF SINTERED ALLOYS FOR AUTOMOTIVE APPLICATIONS"Jesus Filho, Edson Souza de 13 March 2006 (has links)
O objetivo deste trabalho foi desenvolver potenciais materiais para aplicações automotivas, em particular como insertos para assento de válvula em motores de combustão interna à gasolina. O desenvolvimento compreendeu as etapas de processamento dos materiais via metalurgia do pó, tratamento térmico, caracterização microestrutural e mecânica, usinagem e desgaste dos mesmos. O desenvolvimento objetivou principalmente a redução de custo e a aplicação de elementos menos poluentes, excluindo-se, por exemplo, a aplicação do Co devido ao seu alto custo e do Pb devido aos seus efeitos toxicológicos e prejudiciais ao meio ambiente. A realização de uma pesquisa minuciosa na busca de patentes relacionadas indicou que os materiais estudados apresentam composições particulares, e, portanto inéditas. Os resultados encontrados nos ensaios de dureza e de resistência à compressão radial nas amostras tratadas termicamente apresentaram resultados superiores aos da liga comercial atualmente em uso. Testes de usinabilidade em amostras sem tratamento térmico apresentaram comportamento similar ao da liga comercial, indicando que a usinabilidade do material praticamente não foi afetada com a mudança na composição química. Após a etapa de tratamento térmico, as ligas obtidas apresentaram valores de esforços de corte superiores aos do material comercial. Os resultados dos testes de desgaste abrasivo em amostras tratadas termicamente apresentaram menores valores de coeficientes de atrito e perda de massa em todos os casos em relação ao material comercial. Este comportamento é devido aos benefícios introduzidos pelo tratamento térmico executado e pela adição de alguns elementos resistentes ao desgaste na forma de carbonetos de Nb e Ti/W. Os resultados dos esforços de corte apresentaram boa concordância com os resultados dos ensaios de desgaste. Os materiais produzidos apresentam-se como potenciais candidatos para substituir, com vantagens, inserto para assento de válvula a base de Fe-Co em motores de combustão interna a gasolina. / The aim of this work was the development of materials for automotive applications, in particular, valve seat inserts for gasoline combustion engines. The development involved the following activities: processing by powder metallurgy techniques, heat treatment, mechanical and microstructural characterization, machining and wear of materials. This work was undertaken aiming cost reduction of this component by the use of cheaper and less pollutant elements, eliminating the presence of Co and Pb due to their high cost and toxicological effects, respectively. The accomplishment of a thorough research into patents revealed that the materials studied here present particular compositions and were not yet produced. The results of hardness measurements and the transverse radial strength of the studied materials, after heat treatment, revealed superior properties than the commercial alloys applied at the moment. The machining tests of the material without heat treatment indicated a similar behaviour in comparison to the commercial alloy, suggesting that the new alloy chemistry composition was not deleterious in this sense. After heat treatment, the obtained alloys presented a cutting force increase in relation to the commercial alloy. Wear tests results of heat treated materials presented smaller friction coefficient and mass loss than the commercial alloy, in all cases. This was especially achieved due to the advantages offered by heat treatment allied to the addition of NbC and Ti/W carbides. The materials obtained here showed to be potential candidates to substitute with advantages, valve seat inserts made of Fe-Co alloys for gasoline combustion engines.
|
30 |
"PROCESSAMENTO, USINAGEM E DESGASTE DE LIGAS SINTERIZADAS PARA APLICAÇÕES AUTOMOTIVAS" / "OBTENTION, MACHINING AND WEAR OF SINTERED ALLOYS FOR AUTOMOTIVE APPLICATIONS"Edson Souza de Jesus Filho 13 March 2006 (has links)
O objetivo deste trabalho foi desenvolver potenciais materiais para aplicações automotivas, em particular como insertos para assento de válvula em motores de combustão interna à gasolina. O desenvolvimento compreendeu as etapas de processamento dos materiais via metalurgia do pó, tratamento térmico, caracterização microestrutural e mecânica, usinagem e desgaste dos mesmos. O desenvolvimento objetivou principalmente a redução de custo e a aplicação de elementos menos poluentes, excluindo-se, por exemplo, a aplicação do Co devido ao seu alto custo e do Pb devido aos seus efeitos toxicológicos e prejudiciais ao meio ambiente. A realização de uma pesquisa minuciosa na busca de patentes relacionadas indicou que os materiais estudados apresentam composições particulares, e, portanto inéditas. Os resultados encontrados nos ensaios de dureza e de resistência à compressão radial nas amostras tratadas termicamente apresentaram resultados superiores aos da liga comercial atualmente em uso. Testes de usinabilidade em amostras sem tratamento térmico apresentaram comportamento similar ao da liga comercial, indicando que a usinabilidade do material praticamente não foi afetada com a mudança na composição química. Após a etapa de tratamento térmico, as ligas obtidas apresentaram valores de esforços de corte superiores aos do material comercial. Os resultados dos testes de desgaste abrasivo em amostras tratadas termicamente apresentaram menores valores de coeficientes de atrito e perda de massa em todos os casos em relação ao material comercial. Este comportamento é devido aos benefícios introduzidos pelo tratamento térmico executado e pela adição de alguns elementos resistentes ao desgaste na forma de carbonetos de Nb e Ti/W. Os resultados dos esforços de corte apresentaram boa concordância com os resultados dos ensaios de desgaste. Os materiais produzidos apresentam-se como potenciais candidatos para substituir, com vantagens, inserto para assento de válvula a base de Fe-Co em motores de combustão interna a gasolina. / The aim of this work was the development of materials for automotive applications, in particular, valve seat inserts for gasoline combustion engines. The development involved the following activities: processing by powder metallurgy techniques, heat treatment, mechanical and microstructural characterization, machining and wear of materials. This work was undertaken aiming cost reduction of this component by the use of cheaper and less pollutant elements, eliminating the presence of Co and Pb due to their high cost and toxicological effects, respectively. The accomplishment of a thorough research into patents revealed that the materials studied here present particular compositions and were not yet produced. The results of hardness measurements and the transverse radial strength of the studied materials, after heat treatment, revealed superior properties than the commercial alloys applied at the moment. The machining tests of the material without heat treatment indicated a similar behaviour in comparison to the commercial alloy, suggesting that the new alloy chemistry composition was not deleterious in this sense. After heat treatment, the obtained alloys presented a cutting force increase in relation to the commercial alloy. Wear tests results of heat treated materials presented smaller friction coefficient and mass loss than the commercial alloy, in all cases. This was especially achieved due to the advantages offered by heat treatment allied to the addition of NbC and Ti/W carbides. The materials obtained here showed to be potential candidates to substitute with advantages, valve seat inserts made of Fe-Co alloys for gasoline combustion engines.
|
Page generated in 0.0469 seconds