This research is to synthesize polyaniline (PANI) thin film for polymer solar cells as a hole transport layer by using potentiostatic deposition of electrochemical method. In our previous studies, we have shown that the power conversion efficiencies of the solar cell device were improved for the slow polymerization rate. We choose the potentiostatic deposition method to improve the polymerization rate of PANI for the application in industry. In this study, we investigated optical transmittance, absorption spectrum, Highest Occupied Molecular Orbital (HOMO), surface roughness, and surface morphology of the PANI thin film by changing voltages and to discuss the factors on device efficiency. Then, we compared the device structures with hole transport layer PEDOT: PSS by spin-coating process. We found PANI thin films synthesized from different voltages, and the transmittance measurement results were similar. In addition, we found HOMO, surface roughness, and surface morphology of PANI thin film that varies with different voltages. The power conversion efficiencies of the device mainly were affected by the surface roughness and morphology of PANI thin film surface. Comparing to other parameters, PANI thin film polymerized at 0.8V owns the most appropriate surface roughness and surface morphology. The power conversion efficiency was up to 1.52% under AM 1.5G illumination based on ITO (150 nm) / PANI (75 nm) / P3HT: PCBM (100 nm) / Al (200 nm), and the device area of 0.16 cm2.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第20381号 / 工博第4318号 / 新制||工||1669(附属図書館) / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 木本 恒暢, 教授 白石 誠司, 准教授 浅野 卓 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM

The π-conjugated organic and polymeric semiconducting materials have attracted much attention in the past years due to their significant potential in applications to electronic and optoelectronic devices including organic field-effect transistors (OFETs), organic photovoltaics (OPVs), and organic light-emitting diodes (OLEDs), etc. Yet, organic and polymeric semiconductors still have challenges associated with their relatively low charge carrier (hole and electron) transport mobilities and ambient stability in OFET applications. This dissertation discusses the molecular engineering on backbones and side-chains of π-conjugated semiconducting polymers to enhance the hole and electron field-effect mobilities. Three donor-acceptor copolymers, the hole transport (p-type) poly(hexathiophene-co-benzo- thiazole) (PBT6), the hole transport poly(thiophenes-benzothiadiazole-thiophenes-diketopyrrolo- pyrrole) (pTBTD), and the electron transport (n-type) poly(dithieno-diketopyrrolopyrrole-bithiazole) (PDBTz) have been developed. Besides, the effect of polymer side chains on polymer solution-processability and charge carrier transport properties was systematically investigated: a side chain 5-decylheptadecyl having the branching position remote from the polymer backbone merges the advantages of the improved solubility from traditional branched side chains in which the branch chains are close to polymer backbone and the effective π-π intermolecular interactions commonly associated with linear side chains. This indicates the potential of side chain engineering to facilitate the charge carrier transport performance of organic and polymeric semiconductors. Additionally, PDBTz solution-processing to OFETs based on non-halogenated solvents (xylenes and tetralin) was studied. The resultant thin-film OFET devices based on non-halogenated solvents exhibited similar film morphology and field-effect electron mobilities as the counterparts based on halogenated solvents, indicative of the feasibility of developing high mobility OFET devices through more environmentally-benign processing.

Solid-state dye-sensitized solar cells (ssDSSCs) and recently developed perovskite solar cells (PSCs) have attracted a great attention in the scientific field of photovoltaics due to their low cost, absence of solvent, simple fabrication and promising power conversion efficiency (PCE). In these types of solar cell, the dye molecule or the perovskite can harvest the light on the basis of electron excitation. Afterwards, the electron and hole are collected at the charge transport materials. Photoelectrochemical polymerization (PEP) is employed in this thesis to synthesize conducting polymer hole transport materials (HTMs) for ssDSSCs. We have for the first time developed aqueous PEP in comparison with the conventional organic PEP with acetonitrile as solvent. This water-based PEP could potentially provide a low-cost, environmental-friendly method for efficient deposition of polymer HTM for ssDSSCs. In addition, new and simple precursors have been tested with PEP method. The effects of dye molecules on the PEP were also systematically studied, and we found that (a) the bulky structure of dye is of key importance for blocking the interfacial charge recombination; and (b) the matching of the energy levels between the dye and the precursor plays a key role in determining the kinetics of the PEP process. In PSCs, the HTM layer is crucial for efficient charge collection and its long term stability. We have studied different series of new molecular HTMs in order to understand fundamentally the influence of alkyl chains, molecular energy levels, and molecular geometry of the HTM on the photovoltaic performance. We have identified several important factors of the HTMs for efficient PSCs, including high uniformity of the HTM capping layer, perovskite-HTM energy level matching, good HTM solubility, and high conductivity. These factors affect interfacial hole injection, hole transport, and charge recombination in PSCs. By systematical optimization, a promising PCE of 19.8% has been achieved by employing a new HTM H11. We believe that this work could provide important guidance for the future development of new and efficient HTMs for PSCs.

No description available.

This research is to synthesize PANI (polyaniline) thin film for polymer organic solar cells as a hole transport layer on the top of ITO substrate by using electrochemical (cyclic voltammetry) method. The device structure is ITO (150 nm) / PANI (50 nm) / P3HT: PCBM (100 nm) / Al (200 nm). We investigated surface morphology, conductivity, and light transmission of the PANI thin film from different aniline monomer concentration and studied the factors on device efficiency, also compared with the device structured with hole transport layer PEDOT:PSS. In this study, we found PANI thin films synthesized with different aniline monomer concentration, their light transmission over 80% at the range of 450 nm ~ 650nm wavelength and the conductivity up to 0.6 S/cm. It shows that PANI thin film suitably act as hole transport layer. In addition, we found morphology of PANI thin film that varied with different aniline monomer concentration. The power conversion efficiency of the device mainly affected by morphology with different aniline monomer concentration. Comparing to other parameters of concentration, the 0.3M aniline monomer concentration polymerized PANI thin film owned the most appropriate surface morphology, and the power conversion efficiency up to 1.76%.

京都大学 / 0048 / 新制・課程博士 / 博士(エネルギー科学) / 甲第19829号 / エネ博第335号 / 新制||エネ||67(附属図書館) / 32865 / 京都大学大学院エネルギー科学研究科エネルギー応用科学専攻 / (主査)教授 松田 一成, 教授 佐川 尚, 教授 大垣 英明 / 学位規則第4条第1項該当 / Doctor of Energy Science / Kyoto University / DGAM

abstract: The inexorable upsurge in world’s energy demand has steered the search for newer renewable energy sources and photovoltaics seemed to be one of the best alternatives for energy production. Among the various photovoltaic technologies that emerged, organic/polymer photovoltaics based on solution processed bulk-heterojunctions (BHJ) of semiconducting polymers has gained serious attention owing to the use of inexpensive light-weight materials, exhibiting high mechanical flexibility and compatibility with low temperature roll-to-roll manufacturing techniques on flexible substrates. The most widely studied material to date is the blend of regioregular P3HT and PC61BM used as donor and acceptor materials. The object of this study was to investigate and improve the performance/stability of the organic solar cells by use of inexpensive materials. In an attempt to enhance the efficiency of organic solar cells, we have demonstrated the use of hexamethyldisilazane (HMDS) modified indium tin oxide (ITO) electrode in bulk heterojunction solar cell structure The device studies showed a significant enhancement in the short-circuit current as well as in the shunt resistance on use of the hexamethyldisilazane (HMDS) layer. In another approach a p-type CuI hole-transport layer was utilized that could possibly replace the acidic PEDOT:PSS layer in the fabrication of high-efficiency solar cells. The device optimization was done by varying the concentration of CuI in the precursor solution which played an important role in the efficiency of the solar cell devices. Recently a substantial amount of research has been focused on identifying suitable interfacial layers in organic solar cells which has efficient charge transport properties. It was illustrated that a thin layer of silver oxide interfacial layer showed a 28% increase in power conversion efficiency in comparison to that of the control cell. The optoelectronic properties and morphological features of indium-free ZnO/Ag/MoOx electrodes was also studied. Organic solar cells on these composite electrodes revealed good optical and electrical properties, making them a promising alternative indium free and PEDOT:PSS-free organic solar cells. Lastly, inverted solar cells utilizing zinc oxide and yttrium doped zinc oxide electron transport was also created and their device properties revealed that optimum annealing conditions and yttrium doping was essential to obtain high efficiency solar cells. / Dissertation/Thesis / Doctoral Dissertation Chemistry 2015

Polymer solar cells form a promising technology for converting sunlight into electricity, and have reached record efficiencies over 10% and lifetimes of several years. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor materials in the active layer. To achieve longer lifetimes, degradation processes in the materials have to be understood. In this thesis, a set of complementary spectroscopy and microscopy techniques, among which soft X-ray techniques have been used to determine the morphology of polymer:fullerene based active layers. We have found that the morphology of TQ1:PC70BM films is strongly influenced by the processing solvent and the use of solvent additives. We have also found, by using soft X-ray techniques, that not only the light-absorbing polymer TQ1, but also the fullerene is susceptible to photo-degradation in air. Moreover, the fullerene degradation is accelerated in the presence of the polymer. Additionally, this thesis addresses the role of the interfacial layers for device performance and stability. The commonly used hole transport material PEDOT:PSS has the advantage of being solution processable at room temperature, but this layer is also known to contribute to the device degradation. We have found that low-temperature processed NiOx is a promising alternative to PEDOT:PSS, leading to improved device performance. Even for encapsulated polymer solar cells, some photo-induced degradation of the electrical performance is observed and is found to depend on the nature of the hole transport material. We found a better initial stability for solar cells with MoO3 hole transport layers than with PEDOT:PSS. In the pursuit of understanding the initial decrease in electrical performance of PEDOT:PSS-based devices, simulations were performed, from which a number of degradation sources could be excluded. / With the increasing global demand for energy, solar cells provide a clean method for converting the abundant sunlight to electricity. Polymer solar cells can be made from a large variety of light-harvesting and electrically conducting molecules and are inexpensive to produce. They have additional advantages, like their mechanical flexibility and low weight, which opens opportunities for novel applications. In order for polymer solar cells to be more competitive, however, both the power conversion efficiencies and lifetimes need to further improve. One way to achieve this is to optimize the morphology of the active layer. The active layer of a polymer solar cell consists of electron donating and electron accepting molecules whose distribution in the bulk of the film is a major factor that determines the solar cell performance. This thesis presents the use of complementary spectroscopy and microscopy methods to probe the local composition in the active layer of polymer solar cells. The stability of the active layer is studied and the interplay between the photo-degradation of the donor and acceptor molecules is investigated. Additionally, this thesis addresses how the interfacial layers between the active layer and the electrodes can influence device performance and stability. / <p>I publikationen felaktigt ISBN 978-91-7063-739-1</p>

The search for renewable energy resources and ways to harvest them has become a global mainstream topic among researchers nowadays, with solar cells and thermoelectric generators among the energy harvesting technologies currently being researched in vast. CZTS (Cu2ZnSnS4), a p-type semiconducting material initially researched to replace copper indium gallium selenide (CIGS) as the light absorbing layer in thin film solar cells, was studied in this doctoral work for alternative uses in energy harvesting. This work aims to systemically investigate the prospects of CZTS to be used as hole transport layers and thermoelectric generators. CZTS thin film was successfully fabricated using a versatile approach involving hot-injection synthesis of CZTS nanoparticles ink followed by spin coating and thermal treatment. Results obtained revealed the possibility to fine control CZTS thin film fabrication based on ink concentration and spin. Besides that, thermal treatment temperature was found to affect the film’s overall properties, where an increase in thermal treatment temperature improved the degree of crystallinity and electrical properties. In addition, a phase change going from less stable cubic and wurtzite structures to a more stable tetragonal structure was also observed. Furthermore, CZTS was found to be a good candidate to replace the commonly used organic hole transport layer in perovskite solar cells, with potentials in improving performance and stability. In addition, CZTS also possessed good transport properties to be a potential p-type material in a thermoelectric generator, with the preliminary performance of fabricated CZTS/AZO thermoelectric generator showing a maximum power output of ~350 nW at ~170 KΔT. These findings provide new perspectives for CZTS in energy harvesting applications, despite the struggle in its development as the absorber layer in thin film solar cells. Besides providing a deeper understanding of CZTS and its vast possibilities in energy harvesting applications, promising future research stemming from this work is also limitless, reinventing ways in material studies, in search of alternative applications which may be of benefit.