O objetivo deste trabalho foi desenvolver potenciais materiais para aplicações automotivas, em particular como insertos para assento de válvula em motores de combustão interna à gasolina. O desenvolvimento compreendeu as etapas de processamento dos materiais via metalurgia do pó, tratamento térmico, caracterização microestrutural e mecânica, usinagem e desgaste dos mesmos. O desenvolvimento objetivou principalmente a redução de custo e a aplicação de elementos menos poluentes, excluindo-se, por exemplo, a aplicação do Co devido ao seu alto custo e do Pb devido aos seus efeitos toxicológicos e prejudiciais ao meio ambiente. A realização de uma pesquisa minuciosa na busca de patentes relacionadas indicou que os materiais estudados apresentam composições particulares, e, portanto inéditas. Os resultados encontrados nos ensaios de dureza e de resistência à compressão radial nas amostras tratadas termicamente apresentaram resultados superiores aos da liga comercial atualmente em uso. Testes de usinabilidade em amostras sem tratamento térmico apresentaram comportamento similar ao da liga comercial, indicando que a usinabilidade do material praticamente não foi afetada com a mudança na composição química. Após a etapa de tratamento térmico, as ligas obtidas apresentaram valores de esforços de corte superiores aos do material comercial. Os resultados dos testes de desgaste abrasivo em amostras tratadas termicamente apresentaram menores valores de coeficientes de atrito e perda de massa em todos os casos em relação ao material comercial. Este comportamento é devido aos benefícios introduzidos pelo tratamento térmico executado e pela adição de alguns elementos resistentes ao desgaste na forma de carbonetos de Nb e Ti/W. Os resultados dos esforços de corte apresentaram boa concordância com os resultados dos ensaios de desgaste. Os materiais produzidos apresentam-se como potenciais candidatos para substituir, com vantagens, inserto para assento de válvula a base de Fe-Co em motores de combustão interna a gasolina. / The aim of this work was the development of materials for automotive applications, in particular, valve seat inserts for gasoline combustion engines. The development involved the following activities: processing by powder metallurgy techniques, heat treatment, mechanical and microstructural characterization, machining and wear of materials. This work was undertaken aiming cost reduction of this component by the use of cheaper and less pollutant elements, eliminating the presence of Co and Pb due to their high cost and toxicological effects, respectively. The accomplishment of a thorough research into patents revealed that the materials studied here present particular compositions and were not yet produced. The results of hardness measurements and the transverse radial strength of the studied materials, after heat treatment, revealed superior properties than the commercial alloys applied at the moment. The machining tests of the material without heat treatment indicated a similar behaviour in comparison to the commercial alloy, suggesting that the new alloy chemistry composition was not deleterious in this sense. After heat treatment, the obtained alloys presented a cutting force increase in relation to the commercial alloy. Wear tests results of heat treated materials presented smaller friction coefficient and mass loss than the commercial alloy, in all cases. This was especially achieved due to the advantages offered by heat treatment allied to the addition of NbC and Ti/W carbides. The materials obtained here showed to be potential candidates to substitute with advantages, valve seat inserts made of Fe-Co alloys for gasoline combustion engines.

O objetivo deste trabalho foi desenvolver potenciais materiais para aplicações automotivas, em particular como insertos para assento de válvula em motores de combustão interna à gasolina. O desenvolvimento compreendeu as etapas de processamento dos materiais via metalurgia do pó, tratamento térmico, caracterização microestrutural e mecânica, usinagem e desgaste dos mesmos. O desenvolvimento objetivou principalmente a redução de custo e a aplicação de elementos menos poluentes, excluindo-se, por exemplo, a aplicação do Co devido ao seu alto custo e do Pb devido aos seus efeitos toxicológicos e prejudiciais ao meio ambiente. A realização de uma pesquisa minuciosa na busca de patentes relacionadas indicou que os materiais estudados apresentam composições particulares, e, portanto inéditas. Os resultados encontrados nos ensaios de dureza e de resistência à compressão radial nas amostras tratadas termicamente apresentaram resultados superiores aos da liga comercial atualmente em uso. Testes de usinabilidade em amostras sem tratamento térmico apresentaram comportamento similar ao da liga comercial, indicando que a usinabilidade do material praticamente não foi afetada com a mudança na composição química. Após a etapa de tratamento térmico, as ligas obtidas apresentaram valores de esforços de corte superiores aos do material comercial. Os resultados dos testes de desgaste abrasivo em amostras tratadas termicamente apresentaram menores valores de coeficientes de atrito e perda de massa em todos os casos em relação ao material comercial. Este comportamento é devido aos benefícios introduzidos pelo tratamento térmico executado e pela adição de alguns elementos resistentes ao desgaste na forma de carbonetos de Nb e Ti/W. Os resultados dos esforços de corte apresentaram boa concordância com os resultados dos ensaios de desgaste. Os materiais produzidos apresentam-se como potenciais candidatos para substituir, com vantagens, inserto para assento de válvula a base de Fe-Co em motores de combustão interna a gasolina. / The aim of this work was the development of materials for automotive applications, in particular, valve seat inserts for gasoline combustion engines. The development involved the following activities: processing by powder metallurgy techniques, heat treatment, mechanical and microstructural characterization, machining and wear of materials. This work was undertaken aiming cost reduction of this component by the use of cheaper and less pollutant elements, eliminating the presence of Co and Pb due to their high cost and toxicological effects, respectively. The accomplishment of a thorough research into patents revealed that the materials studied here present particular compositions and were not yet produced. The results of hardness measurements and the transverse radial strength of the studied materials, after heat treatment, revealed superior properties than the commercial alloys applied at the moment. The machining tests of the material without heat treatment indicated a similar behaviour in comparison to the commercial alloy, suggesting that the new alloy chemistry composition was not deleterious in this sense. After heat treatment, the obtained alloys presented a cutting force increase in relation to the commercial alloy. Wear tests results of heat treated materials presented smaller friction coefficient and mass loss than the commercial alloy, in all cases. This was especially achieved due to the advantages offered by heat treatment allied to the addition of NbC and Ti/W carbides. The materials obtained here showed to be potential candidates to substitute with advantages, valve seat inserts made of Fe-Co alloys for gasoline combustion engines.

No description available.

The project elaborated in a frame of Master‘s degree branch M-STG focuses on the design of a technology of sandwich coil used for connecting the aircraft floor sandwich panels to the fuselage bulkheads. The product is made of a lightweight aluminium alloy AlMn1. Combined cold extrusion with upsetting of the flange was chosen as the most fitting technology due to the manufacturing requirements and production series size of 120 000 pieces per year. The component is manufactured from a block blank in three operations by a progressive forming machine TPM 8-A with a nominal force of 1000 kN from Šmeral Brno a.s. producer. Within the project, tools for the production of the part were designed and also technical calculations for individual operations and technical and economic evaluation of production were made. The price of the component is estimated to be at least CZK 7,33.

The aim of this thesis is to design a robotic cell for automated injection molding operation. At the beginning of this paper, the input parameters and the assignment are analyzed. This is then followed up by the layout of the workplace, design of its equipment, selection of robots and the design of their end effectors and peripherals with regard to the specified boundary conditions and operator’s safety. The output of this work is a 3D cell model and its simulation model in PLM software Siemens Process Simulate, which verifies the production cycle time.

My thesis solveses the office building. The building will be located in Šumperk. It will be located near the center. The building has two floors and a partial basement floor. Ceilings are beams with ceramic inserts and reinforced concrete slabs. Vertical structure consists of a ceramic blocks in the aboveground parts and concrete blocks in the underground section. The roof is walked on vegetation. The staircase is reinforced concrete, monolithic. The entire building is insulated with mineral wool. Basement is insulated with polystyrene foam.

This thesis is focused on application samples with the inner insert used for Charpy impact test. This insert is welded to additional material by electron beam with pre-selected welded parameters. These parameters were chosen from data of performed experiments on homogenous welds. Resulting heterogenous weld was performed of evaluation of the microstructure, chemical composition and microhardness. Experimental materials were used austenitic steel 17 240 and ferritic steel 17 153 used on high-temperature applications.

Today’s transportation highly depends on hydrocarbon fuels, and reducing the weight could help a lot in reducing the air pollutants and carbon footprints in the environment to comply with the strict regulations set by reputable standard organizations in the world. Utilizing lightweight materials in automobile parts is one of the key factors to succeed in meeting the goals defined in the standards. Replacing the conventional single material component with a multi-material component having the same geometry but lighter weight could help the automakers to achieve these goals. Compound casting is one of the methods to produce such components. The aluminum alloy/ductile iron bimetal component produced by compound casting was investigated. During the production of the experimental sample of the compound casting, component two parameters were considered, melt-to-solid volume ratio and pre-heat temperature of the solid insert. The results showed that the increasing melt-to-solid volume ratio caused the formation of a stronger metallurgical bond between the two materials compared to the lower melt-to-solid volume ratio. However, pre-heating the solid insert under the atmospheric condition caused the formation of iron oxide layers on the surface, and as a result, no metallurgical bonding was formed, no matter which melt-to-solid volume ratio was used during the production process. So, inspired by AlFin process, the solid inserts were first dipped inside the aluminum alloy bath with the target temperature of 750 °C for two extended periods, 15 minutes and 30 minutes, to ensure that the preliminary metallurgical bonds were formed at the interface surfaces without disturbance by the surrounding atmosphere. To make the experimental components and to develop the metallurgical bonds, the aluminized inserts were then quickly placed inside the sand molds, and the cast alloy was poured inside the molds and around the inserts immediately after placement. In this way, although the formation of the aluminum oxide layer was unavoidable on the surfaces of the aluminized inserts, there was still liquid aluminum alloy melt underneath, which could be easily washed away during the pouring of the cast alloy.Nevertheless, the metallurgical bonds in the compound casting products having a lower melt-to-solid volume ratio didn’t withstand the shear loads and only the product having a higher melt-to-solid volume ratio with the aluminized insert dipped for a longer time could resist against the loads. In addition to the mechanical strength of the experimental products, their metallurgical bonds were specified and characterized using microscopic examination and EDS analysis. The successful results of the experimental product were then proposed to modify the design of a model from the automobile industry, called the truck wheel hub. / Dagens transport beror starkt på kolvätebränslen, och att minska vikten kan hjälpa mycket att minska luftföroreningar och kolavtryck i miljön för att följa de strikta regler som ställts av ansedda standardorganisationer i världen. Att använda lätta material i bildelar är en av de viktigaste faktorerna för att lyckas uppfylla de mål som fastställs i standarderna. Att ersätta den konventionella komponenten med enstaka material med en komponent med flera material som har samma geometri men lättare vikt kan hjälpa biltillverkarna att uppnå dessa mål. Gjutning av föreningar är en av metoderna för att producera sådana komponenter. Aluminiumlegeringen / segjärn-bimetalkomponenten framställd genom sammansatt gjutning undersöktes. Under framställningen av det experimentella provet av gjutning av föreningen beaktades komponent två parametrar, volymförhållandet smält till fast material och förvärmningstemperaturen för det fasta insatsen. Resultaten visade att det ökande smält-till-fasta volymförhållandet orsakade bildandet av en starkare metallurgisk bindning mellan de två materialen jämfört med det lägre förhållandet mellan smält och fast volym. Förvärmning av den fasta insatsen under atmosfäriskt tillstånd orsakade emellertid bildningen av järnoxidskikt på ytan, och som ett resultat bildades ingen metallurgisk bindning, oavsett vilket smält-till-fast volymförhållande användes under produktionsprocessen . Så, inspirerad av AlFin-processen, doppades de fasta insatserna först in i aluminiumlegeringsbadet med måttemperaturen 750 ° C under två långa perioder, 15 minuter och 30 minuter, för att säkerställa att de preliminära metallurgiska bindningarna bildades vid gränsytans ytor utan störningar av den omgivande atmosfären. För att tillverka de experimentella komponenterna och för att utveckla de metallurgiska bindningarna placerades sedan de aluminiumiserade skärmen snabbt inuti sandformarna, och den gjutna legeringen hälldes in i formarna och runt insatserna omedelbart efter placering. På detta sätt, även om bildningen av aluminiumoxidskiktet var oundvikligt på ytorna på de aluminiumförsedda insatserna, fanns det fortfarande flytande aluminiumlegeringssmälta under, vilket lätt kunde tvättas bort under hällningen av den gjutna legeringen.Icke desto mindre tål de metallurgiska bindningarna i de sammansatta gjutprodukterna med ett lägre volym-till-fast volymförhållande inte skjuvbelastningarna och endast produkten med ett högre smält-till-fast volymförhållande med den aluminiumiserade insatsen doppades under en längre tid kunde motstå mot lasterna. Förutom de experimentella produkternas mekaniska styrka specificerades och karakteriserades deras metallurgiska bindningar med mikroskopisk undersökning och EDS-analys. De framgångsrika resultaten av den experimentella produkten föreslogs sedan att modifiera utformningen av en modell från bilindustrin, kallad truckhjulnavet.

No description available.

Ausgehend von der Anwendung von Folienhinterspritzprozessen für dekorative Zwecke wurde deren Nutzung für die Integration elektronischer Strukturen in Kunststoffbauteile untersucht. Die Herstellung der elektronischen Bauelemente erfolgte mittels verschiedener Druckverfahren mit elektrisch leitfähigen und dielektrischen Materialien auf Polycarbonatfolien. Im Fokus standen zum einen kapazitiv auslesbare Speicherstrukturen und zum anderen Elektrolumineszenzleuchten. Nach dem Druck wurden die bedruckten Folien z. T. verformt und hinterspritzt. In der Arbeit wird auf die Auswirkungen der Verform- und Hinterspritzprozesse eingegangen. Schwerpunktmäßig wird die elektronische bzw. optische Funktionalität der Bauelemente, die Beeinflussung durch Klimaveränderungen und die Haftfestigkeit der Folien betrachtet. Im Ergebnis konnten erstmals die Realisierbarkeit hinterspritzter elektronischer Bauelemente nachgewiesen sowie verschiedene Einflussfaktoren auf deren Funktionalität identifiziert werden. / Based on the application of film insert molding for graphic purposes, the utilization of this process for the integration of electronic devices into plastic components was examined. The manufacturing of the electronic devices was realized by applying electrical conductive and dielectric inks on polycarbonate foil by various printing processes. Capacitive data storage patterns and electroluminescent lamps are the main applications. The production sequence included the printing process, forming of the foil where required and back injection molding. The impact of forming and film insert molding was investigated. The electronic and/or optical functionality of the devices, the influence of ambient conditions like temperature or humidity and the adhesion strength of the foils were in the focus of the evaluation. As a result, the feasibility of film insert molded electronic devices could be verified and various impact factors could be identified for the first time.