This thesis presents the application of an imprinted mercury(lI) polymer that we synthesized by copolymerizing the functional and cross-linking monomers, N'-[3-(Trimethoxysilyl)propyl] diethylenetriamine (TPET) and tetraethylorthosilicate (TEOS) in the presence of mercury (II) ions as template. A bulk polymerization method following a double-imprinting procedure and employing hexadecyltrimethylammonium bromide (CTAB), as a second template to improve the efficiency of the polymer was employed in the synthesis. The imprinted polymer particles were characterized by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and their average size determined by screen analysis using standard test sieves. The relative selective coefficients (k') of the imprinted polymer evaluated from selective binding studies between Hg ²⁺and Cu²⁺ or Hg²⁺ and Cd²⁺, were 10588 and 3147, respectively. These values indicated highly favored Hg²⁺ extractions over the two competing ions. Application of the polymer to various real water samples (tap, sea, river, pulverized coal solution, treated and untreated sewerage from the vicinity of Grahamstown in South Africa) showed high extraction efficiencies (EEs) of Hg²⁺ ions; (over 84% in all cases) as evaluated from the detected unextracted Hg²⁺ ions by inductively coupled plasma optical emission spectroscopy (ICP-OES). The limit of detection (LOD, 3ơ) of the method was evaluated to be 0.036 ng ml⁻¹ and generally the data (n=10) had percentage relative standard deviation (%RSD) of less than 4%. These findings indicate that the double-imprinted polymer has potential to be used as an efficient extraction material for the selective pre-concentration of mercury(lI) ions in aqueous environments. / KMBT_363 / Adobe Acrobat 9.54 Paper Capture Plug-in

Recent advances in the area of nanotechnology have led to interesting applications of nanomaterials in medicine, especially in the areas of imaging and treatment. This thesis presents the development of two molecularly imprinted polymers (MIPs) based on the same fluorescent functional monomer. One MIP, prepared in the bulk format, is investigated for its ability to detect tamoxifen and its metabolites. The other MIP synthesised in the nanogel format, holds the potential to be used as pH-responsive drug delivery system. Four objectives were identified within this project. The first was the design and synthesis of fluorescent functional monomer. Two coumarin derivatives carrying a polymerisable unit, for covalent bonding within the polymer, and a carboxylic moiety, for interaction site with the template, were synthesised and characterised. However, only one of them (the VCC: 6-vynilcoumarin-4-carboxylic acid) showed high fluorescent yield and was selected as functional monomer. The second objective involved the development of a detection system based on bulk MIP containing the VCC fluorescent monomer. This system proved effective in generating a detectable signal upon binding the analytes. The signal was observed as a quenching of the polymer fluorescence and it was proportional to the amount of target molecules detected. The third objective was the preparation of tamoxifen-imprinted nanogels for potential application in the drug delivery field. The optimisation of the procedure gave a set of NIP/MIP with the desired solubility, particle size and fluorescence emission. These nanogels were then employed in the last objective, which involved the toxicity study and evaluation of the drug loading on of transgenic line of zebrafish. The nanogels were non-toxic at the tested concentrations and the presence of tamoxifen was confirmed.

<p>In the present work, molecular dynamics simulations were used to evaluate the molecular interactions in prepolymerization mixtures, as occurring during production of molecularly imprinted polymers. The systems simulated were produced based on earlier studies for reference of results. Four systems were simulated in order to investigate the effect on molecular interactions based upon the choice of porogen (acetonitrile or chloroform) and proton transfers. The systems consisted of phenylalanine anilide as template, methacrylic acid as functional monomer, ethylene glycol dimethacrylate as crosslinker and 2,2’-azobis-(2-methylpropionitrile) as radical initiator, with either acetonitrile or chloroform as porogen. Trajectories from the simulations were evaluated through radial distribution function analysis, grid density analysis and hydrogen bond analysis to investigate molecular interactions and complex formations in the simulated complete prepolymerization mixtures. Focus was on functional monomer-template, crosslinker-template and template-template complex formations. The results showed that the porogen influences molecular interactions in complete prepolymerization mixtures. Formation of higher order complexes was confirmed in all of the systems involving all of the investigated molecular species in the prepolymerization mixtures. The results could also confirm the presence of previously observed complexes between functional monomer and template (2:1 and 1:1 stoichiometry) and the prevalence of template dimerization, as well as a high involvement of crosslinker in complex formation.</p>

Not available

Thesis (Ph. D.)--University of Texas at Austin, 2006. / Vita. Includes bibliographical references.

Thesis (Ph. D.)--Chemistry and Biochemistry, Georgia Institute of Technology, 2005. / Weck, Marcus, Committee Member ; Josowicz, Mira, Committee Member ; Janata, Jiri, Committee Member ; Mizaikoff, Boris, Committee Chair ; Huang, Ching-Hua, Committee Member. Includes bibliographical references.

A Ni(II)-dimethylglyoxime ion imprinted polymer {Ni(II)-DMG IIP} was synthesized by the trapping method using the bulk polymerisation format. The structures of the imprinted and non-imprinted polymer were evaluated by infrared spectroscopy and the morphology was observed by scanning electron microscopy. The Ni(II)-DMG IIP was optimised for pH, mass, time and by the uniform design experimental method for the molar ratios of monomer to crosslinker to porogen and template to ligands as well as keeping these parameters constant and varying the quantities of initiator, 2,2'-azobisisobutyronitrile (AIBN). The optimum pH was 8.5, optimum mass was 50 mg, optimum time was 1 min and the optimum molar ratios of crosslinker to monomer, monomer to template and nickel(II) sulfate hexahydrate (NiSO₄.6H₂O) to 4-vinylpyridine to dimethylglyoxime were found to be 3.3:1.0, 0.6:1.0 and 1.0:0.6:3.6 respectively with 30 mg and 8 mL as the optimum amounts of initiator and porogen respectively. Through this optimisation, recovery of Ni(II) was increased from 98 to 100%. Selectivity of the ion imprinted polymer was evaluated by analysing, using an inductively coupled plasma-optical emission spectrometer, for Ni(II) ions that were spiked with varying concentrations of Co(II), Cu(II), Zn(II), Pd(II), Fe(II), Ca(II), Mg(II), Na(I) and K(I) in aqueous samples. Selectivity studies also confirmed that the ion imprinted polymer had very good selectivity characterised by % RSD of less than 5 %. Co(II) was the only ion found to slightly interfere with the determination of Ni(II). The limits of detection and quantification were found to be 3x10⁻⁴ μg/mL and 9x10⁻⁴ μg/mL respectively. The method was evaluated by a custom solution of ground water certified reference material (SEP-3) and sandy soil reference material (BCR-142R) and the concentrations of Ni(II) obtained were not significantly different to the certified ones. The Ni(II)-DMG IIP was then evaluated in aqueous and soil samples where recoveries of 93 to 100% and 98 to 99% respectively were obtained with enrichment factors ranging from 2 to 18 in aqueous and 27 to 40 in soil samples. Finally, the Ni(II)-DMG IIP was used to analyse mine tailings samples and Ni(II) recovery of 99% was obtained with an enrichment factor of 2.

The synthesis of materials with molecular recognition properties has become a topic of great technological and scientific interest. Molecular imprinting is one of the most effective strategies in preparing highly selective synthetic receptors. The technique of molecular imprinting involves the copolymerization of functional and cross-linking monomers in the presence of a molecular template. Following polymerization and subsequent removal of the template, the molecularly imprinted polymer (MIP) retains a “molecular memory” of the template. During rebinding, the resultant polymer shows higher affinity and selectivity towards the molecular template when compared to other structural analogs. Ease of preparation and high thermal and chemical stability of this class of materials offers a broad range of potential applications. Promising areas of application include separation, chromatography, catalysis, sensors, antibody mimics, and drug delivery etc. The thesis entitled “Molecularly Imprinted Polymers based on Fluorescent and Template binding Cross-linker” deals with the design and synthesis of several molecularly imprinted polymers (MIPs) using different functional and cross-linking monomers, the main focus being use of preformed template-monomer complex, use of fluorescent cross-linker and development of functional group containing cross-linker. Chapter 1: An Introduction to Molecularly Imprinted Polymers. The first chapter provides an introduction to the field of molecularly imprinted polymers. It presents an overview of molecular imprinting process including a brief history of its discovery and its evolution to the present form. This chapter further elaborates on the principle of molecular imprinting with an emphasis on different parameters that directly affect their performance. It also provides a brief review of the applications of molecularly imprinted polymers. Chapter 2: Highly Cross-linked Metal Ion Imprinted Polymers. The second chapter deals with the synthesis of series of highly cross-linked metal-ion imprinted polymers. The process of metal ion-imprinting usually involves carrying out the polymerization and cross-linking directly in presence of the appropriate metal ion. In the present study, chemical-immobilization method was adopted which involves the use of preformed metal complexes with polymerizable group for the imprinting. Acrylate complexes of various metal-ions, such as Cu2+, Zn2+, Co2+, Ni2+, Pb2+ and Cr3+, were synthesized prior to polymerization. These pre-assembled complexes were then used to prepare MIPs, in the anticipation that this would lead to enhanced selectivity. Ethyleneglycol dimethacrylate (EGDMA) was used as the cross-linking monomer. As a control, the respective non-imprinted polymers (NIPs) were also made in absence of the template metal ion. Following polymerization, the template metal ion was extracted from the resultant metal ion-imprinted polymer. The selectivity of the metal ion-imprinted polymers was examined by a batch process using analytical tools, such as, Atomic Absorption Spectroscopy (AAS) and Inductively Coupled Plasma Spectroscopy (ICP). The spectroscopic studies revealed significant selectivity of all the MIPs towards the template metal ion. Among all six metal ion-imprinted polymers, Pb2+ and Cr3+ ion-imprinted polymer showed remarkable selectivity, followed by Cu2+ and Zn2+ ion-imprinted polymers. The Co2+ and Ni2+ ion-imprinted polymers exhibited comparatively poor selectivity. Representative plots depicting the selectivity exhibited by Pb2+ and Cr3+ ion-imprinted polymers are shown in Figure 1. These observations were rationalized based on the size and geometric preferences imposed by the imprinted site on the ion that binds to it. Figure 1. Selectivity study for (a) Pb2+ ion-imprinted polymer, (b) Cr3+ ion-imprinted polymer. Chapter 3. Molecularly Imprinted Fluorescent Chemosensor for Copper (II). Cu(II) is a source of important pollutant and therefore, the development of sensors that can detect Cu(II) selectively as well as remove Cu(II) from contaminated samples is an important objective. The use of molecular imprinting technique is an appealing approach in this regard. For this, a fluorophore containing cross-linker, namely 9,10-bis-(acryloyloxymethyl)anthracene (BAMA) was synthesized. This fluorescent cross-linker was used along with the standard cross-linker, EGDMA, for preparing Cu2+ ion-imprinted polymer. The complex of copper methacrylate (Cu-MAA) was prepared prior to polymerization used for the preparation of MIP. The resultant imprinted polymer exhibited quenching of the fluorescence in presence of Cu2+ ion, both in organic and aqueous medium. The efficiency of quenching of NIP (prepared in absence of Cu2+ ion) was significantly lower than that of MIP. A typical stack spectra showing the quenching process, along with a comparison of the quenching efficiency of MIP and NIP is shown in Figure 2. The imprinted polymers showed significant selectivity over other non-template metal ions, thereby reaffirming the importance of the imprinting process. The sensitivity of the fluorescence detection could be enhanced by increasing the level of the fluorophore incorporation. The increased sensitivity in detecting Cu2+ ion, demonstrated by the MIP suggests that a statistically random incorporation of the fluorophore into MIP matrices could be a useful approach for imparting a sensing element to MIPs. Figure 2. Fluorescence spectra of the (a) imprinted (MIP-1) and (b) non-imprinted (NIP-1) polymers in the presence of various concentration of Cu(OAc)2 in methanol. (c) Comparison of quenching efficiency of MIP-1 and NIP-1. Data were collected 3 h after addition of copper solution. I0 and I are the fluorescence intensities at 399 nm of the polymers in the absence presence of copper respectively. Two individual runs are presented in (c). Chapter 4. Molecularly Imprinted Turn-Off-On Sensor. This chapter describes the design and synthesis of molecularly imprinted fluorescent turn-off-on sensor utilizing the same fluorescent cross-linker, BAMA. Combining the process of fluorescence resonance energy transfer (FRET) with molecular imprinting technique, a novel turn-off-on sensor was developed. A molecularly imprinted polymer was prepared using a fluorescent template Coumarin-30 (C-30). C-30 was chosen as the template to ensure a significant overlap of the emission spectra of BAMA and the absorption spectra of C-30, thereby optimizing for FRET. Figure 3. Structures of relevant molecules. The C-30 imprinted polymer exhibited simultaneous quenching in fluorescence (turn-off) of BAMA and enhancement in fluorescence (turn-on) of C-30 (Figure 4). The imprinted polymer showed significantly better performance over the non-imprinted polymer (NIP). Figure 4. Fluorescence spectra of the (a) imprinted (MIP) and (b) non-imprinted (NIP) polymers with increasing concentration of the template Coumarine-30 in methanol. The UV-vis studies revealed that the more effective quenching is indeed due to the affinity for C-30 exhibited by the higher binding imprinted polymer. The imprinted polymer also showed significant selectivity over structurally analogous molecules. Therefore, both high sensitivity and selectivity were realized in such novel off-on sensor. Extension of this concept to other biologically relevant fluorescent templates could lead to potentially useful applications. Chapter 5. Design of New Template Binding Cross-linker. In molecularly imprinted polymers (MIP), high cross-linking density (~80 to 90 mole percent) is essential to ensure high selectivity, which limits the functional (binding) monomer to about 10-20 mole percent. Methacrylic acid (MAA) and ethyleneglycol dimethacrylate (EGDMA) are the most common combination of functional monomer and cross-linker, respectively, used in molecular imprinting. Generally a molecularly imprinted polymer made with this combination, contains only 10-20% binding sites. This limitation of binding site density is an aspect that has largely been overlooked. In order to improve the efficiency of MIP materials by enhancing the number of binding sites, a new cross-linking monomer (CYDI, 1) with two carboxylic acid groups was designed and synthesized by coupling itaconic anhydride with cyclohexane dimethanol (Figure 5). Figure 5. Structures of relevant molecules. The new functional group bearing cross-linking monomer (1) Itaconate ester of cyclohexanedimethanol (CYDI), the template (2) theophylline (Theop) and the structural analogue of template (3) caffeine (Caff). This new cross-linking monomer was then employed for preparing molecularly imprinted polymer using a drug molecule, theophylline (Theop 2, a bronchodilator) as the template. Seven molecularly imprinted polymers were synthesized with different ratios of CYDI and EGDMA, keeping the cross-linking density constant. The binding efficiency and the selectivity of these imprinted polymers were thoroughly investigated. It was seen that while saturation binding values for theophylline increased continuously with functional cross-linker (CYDI) content, the optimum selectivity with respect to analogous substrate, caffeine, was attained at 40 mol% CYDI. These studies suggest that the approach of using functional group containing cross-linkers could lead to improved MIP performance.

Advantages such as chemical, mechanical and thermal stability together with high selectivity for the templated analyte render molecularly imprinted polymers MIPs interesting alternatives to routinely applied separation materials or antibodies. Nevertheless, many factors such as the choice of functional monomer, cross-linker, and porogenic solvent, as well as the ratio between template, functional monomer, and cross-linker will affect the resulting imprinting efficiency and polymer particle size and morphology. The research described in this thesis contributes to the development of new synthetic strategies for the generation of imprinted micro- and nanospheres for 17beta-estradiol (E2) focusing on accurate control and optimization of the governing parameters for precipitation polymerization, including the polymerization temperature and the cross-linker, yielding a one-step synthetic approach with superior control on the bead diameter, shape, monodispersity and imprinting efficiency. Thus synthesized imprinting materials for E2 were successfully applied in HPLC separation, solid phase extraction and radioligand binding assays. As the optimization of imprinted materials is based on fundamental understanding of the binding site properties, the investigations is aimed at establishing a more rational basis for further tailoring imprinted materials to the desired analytical application. The relationships between the particle porosity and rebinding properties were detailed, providing useful guidelines for controlling the particle properties for the desired application including, SPE pre-concentration, HPLC separations, and biomimetic binding assays. Furthermore, analytical techniques (1H-NMR and IR, etc.) and molecular modeling were combined in this thesis to facilitate advanced understanding of the fundamental principles governing selective recognition of molecularly imprinted polymers at a molecular level. The molecular interactions involved in the templating process of molecularly imprinted polymers based on the self-assembly approach were simulated in molecular dynamic simulation model by building a modeling system include all the imprinting components with correct ratio, which has never been reported before. Molecular level interactions such as hydrogen bonding, π-π stacking interactions as well as the free energy governing complex formation of E2 with the functional monomers 4-vinylpyridine (4VP) and methacrylic acid (MAA), and the cross-linker divinylbenzene (DVB) were discussed.

The research described in this thesis contributes to the development of new strategies facilitating advanced understanding of the fundamental principles governing selective recognition of molecularly imprinted polymers (MIPs) at a molecular level for the rational optimization of biomimetic materials. The nature of non-covalent interactions involved in the templating process of molecularly imprinted polymers based on the self-assembly approach were investigated with a variety of analytical techniques addressing molecular level interactions. For this purpose, the concerted application of IR and 1H-NMR spectroscopy enabled studying the complexation of the template molecules 2,4-dichlorophenoxyacetic acid, quercetin, and o-, m-, and p-nitrophenol with a variety of functional monomers in the pre-polymerization solution by systematically varying the ratio of the involved components. In aqueous and non protic porogenic solvents, information on the interaction types, thermodynamics, and complex stoichiometry was applied toward predicting the optimum imprinting building blocks and ratios. Molecular dynamics simulations of 2,4-dichlorophenoxyacetic acid and its interactions with the functional monomer 4-vinylpyridine in aqueous and aprotic explicit solvent allowed demonstrating the fundamental potential of computer MD simulations for predicting optimized pre-polymerization ratios and the involved interaction types. The obtained results clearly demonstrate that the application of rapid IR/NMR pre-screening methods in combination with molecular modeling strategies is a promising strategy towards optimized imprinting protocols in lieu of the conventionally applied labor intensive and time-consuming trial-and-error approach. Furthermore, HPLC characterization of the produced MIPs compared to control polymers enabled a systematic approach to imprinting based on advanced understanding of the factors governing the formation of high-affinity binding sites during the polymerization. In addition, the importance of the combination of size, shape, and molecular functionalities for the selective recognition properties of MIPs was investigated. MIPs for the mycotoxins deoxynivalenol and zearalenone and for the antioxidant quercetin were applied as separation materials for advanced sample preparation in beverage analysis. The obtained results demonstrated the potential of MIPs for rapid one-step sample clean-up and pre-concentration from beverages such as wine and beer.