The purpose of the thesis is to investigate the improvement of single-crystal Si solar cell efficiency using porous Indium tin oxide (ITO)/ITO double layer antireflection(AR) coating. The resistivity, transmittance and refraction index of the porous ITO films prepared by supercritical CO2 treatment were investigated. At a 2000 psi pressure and 60¡CC, the resistivity of porous ITO films is 15 £[-cm, the average transmittance is better than 95 %, and the refraction index is 1.54. In addition, the resistivity of ITO thin films fabricated by reactive ratio-frequency magnetron sputtering is 7¡Ñ10-4 £[-cm, the average transmittance are 85 %, and the refraction index is 2.0. For the single crystal-Si solar cell with porous ITO/ITO double layer AR coating, the open circuit voltage, short circuit current, fill factor and efficiency are measured.

For polymer-matrix composites (PMCs) that contain insulating matrices and conducting fillers, the electrical properties of the PMCs are especially sensitive to the local concentration of the fillers in the matrix. For PMCs that have phase-segregated microstructures, better prediction of the properties is possible since enhanced control over the distribution of the filler in the matrix can be achieved. In this research, PMMA-ITO nanocomposites were chosen as the composite system in which to explore alternative microstructures, specifically highly phase-segregated microstructures. The microstructures were primarily controlled by varying the ITO particle size and concentration, and the fabrication parameters used to form the nanocomposites. The motivation for this research was to develop correlations between the microstructure and non-destructive measurements in order to improve the predictability of properties in percolating PMCs. As a result of this work, a novel phase-segregated microstructure was discovered, where ITO aggregate-wire structures self-assembled during the composite forming process. Structural analysis of the specimens was conducted primarily using transmission optical microscopy and scanning electron microscopy (SEM). Impedance spectroscopy and optical spectroscopy were the primary NDE characterization tools used for analyzing the variations among the specimens. Ultra-small angle x-ray scattering (USAXS) and stereological techniques were also used to describe the dimensions of the ITO aggregate-wire structures that self-assembled in the PMMA-ITO nanocomposites.

An aim of this work is a research of a deposition process of indium tin oxide by plasma assisted methods. The thesis deals with plasma diagnostics, e.g. Langmuir probe diagnostics and optical emission spectroscopy, as well as describes experiments of film deposition including their diagnostics, e.g. absorption spectroscopy, X-ray diffractometry and atomic force microscopy.

Porous metal oxides formed by supercritical carbon dioxide (SCCO2) treatments at low temperature were used for displays, solar cells, and light emitting diodes (LEDs) applications. The SCCO2 fluid, also known as green solvents, exhibits low viscosity, low surface tension and high diffusivity as gases, and high density and solubility same with liquids. In this thesis, we successfully fabricated porous antimony-doped tin oxide (ATO) and porous indium tin oxide (ITO) by the SCCO2 treatments. In addition, the treatment can also be used to improve the work function and surface energy of ITO anode of an organic LED (OLED). The performance of the OLEDs was drastically enhanced in comparison with that of the devices without any ITO surface treatments. First, the porous ATO films were formed by the SCCO2 treatment for absorption of silver molecules in silver electro deposition devices. The porosity, resistivity and average optical transmittance of the porous ATO film in visible wavelength were 43.1%, 3 £[-cm and 90.4%, respectively. For the silver electro deposition devices with the porous ATO film, the transmittance contrast ratio of larger than 12 in visible spectrum was obtained at an operating voltage of 1.5 V. Furthermore, for the 0.25 cm2 device, the switching time of 4.5 seconds was achieved by applying a square-wave voltage ranging from 1.5 to -0.2 V between the electrodes. On the other hand, the porous ITO with low refractive index was prepared by SCCO2/IPA treatment on gel-coated ITO thin films. The high refractive index of the ITO film was achieved by long-throw radio-frequency magnetron sputtering technique at room temperature. The index contrast (£Gn) was higher than 0.6 between porous ITO and sputtered ITO films. The large £Gn is useful for fabricating conductive anti-reflection (AR) and high reflection (HR) structures using the porous ITO on sputtered ITO bilayers. The weighted average reflectance and transmittance of 4.3% and 83.1% were achieved for the double-layer ITO AR electrode with a sheet resistance of 1.1 K£[/¡E. For HR structures, the reflectance and sheet resistance were 87.9% and 35 £[/¡E with 4 periods ITO bilayers. Finally, the SCCO2 treatments with strong oxidizer H2O2 were proposed to modify surface property of ITO anode of a fluorescent OLED. The highest work function and surface energy of 5.5 eV and 74.8 mJ/m2 was achieved by the SCCO2/H2O2 treatment. For the OLED with 15 min SCCO2 treatment at 4000 psi, the turn-on voltage and maximum power efficiency of 6.5 V and 1.94 lm/W were obtained. The power efficiency was 19.3% and 33.8% higher than those of the OLEDs with oxygen plasma treated and as-cleaned ITO anodes.

Polymer/inorganic nanoparticle hybrid thin films, primarily composed of functional inorganic nanoparticles, are of great interest to researchers because of their interesting electronic, photonic, and optical properties. In the past two decades, layer-by-layer (LbL) assembly has become one of the most powerful techniques to fabricate such hybrid thin films. This method offers an easy, inexpensive, versatile, and robust fabrication technique for multilayer formation, with precisely controllable nanostructure and tunable properties. In this thesis, various ways to control the structure of hybrid thin films, primarily composed of polyelectrolytes and indium tin oxide (ITO), are the main topics of study. ITO is one of the most widely used conductive transparent oxides (TCOs) for applications such as flat panel displays, photovoltaic cells, and functional windows. In this work, polyethyleneimine (PEI) was used to stabilize the ITO suspensions and improve the film buildup rate during the LbL assembly of poly(sodium 4-styrenesulfonate) (PSS) and ITO. The growth rate was doubled due to the stronger interaction forces between the PSS and PEI-modified ITO layer. The assembly of hybrid films was often initiated by a polyelectrolyte precursor layer, and the characteristics of the precursor layer were found to significantly affect the assembly of the hybrid thin films. The LbL assembly of ITO nanoparticles was realized on several substrates, including cellulose fibers, write-on transparencies, silicon wafers, quartz crystals, and glasses. By coating the cellulose fibers with ITO nanoparticles, a new type of conductive paper was manufactured. By LbL assembly of ITO on write-on transparencies, transparent conductive thin films with conductivity of 10⁻⁴ S/cm and transparency of over 80 % in the visible range were also prepared. As a result of this work on the mechanisms and applications of LbL grown films, the understanding of the LbL assembly of polyelectrolytes and inorganic nanoparticles was significantly extended. In addition to working with ITO nanoparticles, this thesis also demonstrated the ability to grow bicomponent [PEI/SiO₂]n thin films. It was further demonstrated that under the right pH conditions, these films can be grown exponentially (e-LbL), resulting in much thicker films, consisting of mostly the inorganic nanoparticles, in much fewer assembly steps than traditional linearly grown films (l-LbL). These results open the door to new research opportunities for achieving structured nanoparticle thin films, whose functionality depends primarily on the properties of the nanoparticles.

Elektrochemické metody nacházejí využití v mnoha aplikacích (např. senzorice, skladování el. energie nebo katalýze). Jejich nespornou výhodou je nízká finanční náročnost na přístrojové vybavení. Abychom lépe porozuměli procesům probíhajícím na elektrodách, je dobré znát elektronickou pásovou strukturu materiálu elektrody. Úkolem této práce je vyhodnotit výstupní práci a pozici hrany valenčního pásu nových materiálů pro elektrody, konkrétně cínem dopovaného oxidu india pokrytého nanotrubicemi sulfidu wolframičitého. Ultrafialová fotoelektronová spektroskopie a Kelvinova silová mikroskopie jsou metody použité pro tuto analýzu. Zvláštní důraz je kladen na přípravu vzorků elektrod pro měření, aby nedošlo k nesprávné interpretaci výsledků vlivem vnějších efektů jako je např. kontaminace nebo modifikace povrchu.