In the work underlying this thesis solid-phase microextraction (SPME) was evaluated as a passive sampling technique for organophosphate triesters in indoor air. These compounds are used on a large scale as flame-retarding and plastizicing additives in a variety of materials and products, and have proven to be common pollutants in indoor air. The main objective of this work was to develop an accurate method for measuring the volatile fraction. Such a method can be used in combination with active sampling to obtain information regarding the vapour/particulate distribution in different indoor environments. SPME was investigated under both equilibrium and non-equilibrium conditions and parameters associated with these different conditions were estimated. In <b>Paper I</b>, time-weighted average (TWA) SPME under dynamic conditions was investigated in order to obtain a fast air sampling method for organophosphate triesters. Among the investigated SPME coatings, the absorptive PDMS polymer had the highest affinity for the organophosphate triesters and was consequently used in all further work. Since the sampling rate is dependent on the agitation conditions, the linear airflow rates had to be carefully considered. Sampling periods as short as 1 hour were shown to be sufficient for measurements in the ng-μg m-3 range when using a PDMS 100-μm fibre and a linear flow rate above 7 cm s-1 over the fibre. SPME under equilibrium conditions is rather time-consuming, even under dynamic conditions, for slowly partitioning compounds such as organophosphate triesters. Nevertheless, this method has some significant advantages. For instance, the limit of detection is much lower compared to 1 h TWA sampling. Furthermore, the sampling time can be ignored as long as equilibrium has been attained. In <b>Paper II</b>, SPME under equilibrium conditions was investigated and evaluated for organophosphate triester vapours. Since temperature and humidity are closely associated with the distribution constant a simple study of the effect of these parameters was performed. The obtained distribution constants were used to determine the air levels in a common indoor environment. SPME and parallel active sampling on filters yielded similar results, indicating that the detected compounds were almost entirely associated with the vapour phase To apply dynamic SPME method in the field a sampler device, which enables controlled linear airflow rates to be applied, was constructed and evaluated (<b>Paper III</b>). This device was developed for application of SPME and active sampling in parallel. A GC/PICI-MS/MS method was developed and used in combination with active sampling of organophosphate triesters in indoor air (<b>Paper IV</b>). The combination of MS/MS and the soft ionization achieved with methanol as reagent gas yielded high selectivity and detection limits comparable to those provided by GC with nitrogen-phosphorus detection (NPD). The method limit of detection, when sampling 1.5 m3 of air, was in the range 0.1-1.4 ng m-3. In <b>Paper V</b>, the developed MS method was used in combination with SPME for indoor air measurements. The levels detected in the investigated indoor environments range from a few ng to μg m-3. Tris(2-chloropropyl) phosphate was detected at a concentration as high as 7 μg m-3 in a newly rebuilt lecture room.

The aim was to study the prevalence of asthma, eczema, allergy and respiratory symptoms among pupils in Shanxi province, China, in relation to home and school environment and outdoor air pollution. In one study there was a low prevalence of self-reported asthma, eczema and pollen or pet allergy among pupils (9-20y). Rural childhood and consumption of fruit and fish were negatively associated with asthma or allergy, while current urban residency and consumption of hamburgers tended to be risk factors. In another study in junior high school pupils, similar low prevalence of asthma and allergy was found. Compared with pupils at the same age in Uppsala, Sweden, asthma and allergy were less common while daytime attacks of breathlessness were more common in Chinese pupils. Parental asthma or allergy was a predictor of asthma symptoms. Factors in the home environment such as new floor, new furniture and ETS exposure were risk factors for asthma symptoms. Crowdedness, dust amount, CO2, temperature and air humidity were negatively associated with respiratory symptoms. Microbial chemical components like muramic acid and ergosterol, markers for bacteria and fungi, were negatively associated with wheeze or daytime attacks of breathlessness. The associations with endotoxin varied depending on the length of 3-hydroxy fatty acids of the lippopolysaccharides (LPS). Among outdoor air pollutants, SO2 and formaldehyde were positively associated with asthma symptoms or respiratory infections. In addition, indoor SO2, NO2 and formaldehyde were positively associated with asthma symptoms and respiratory infections. In conclusion, rural childhood and dietary factors can be protective for asthma and allergy. ETS and chemical emissions from new material at home can be risk factors for asthmatic symptoms. In the school environment, factors of indoor origin seemed to be generally protective for respirator symptoms while factors of outdoor origin seemed to be risk factors.

Humans are exposed to persistent organic pollutants (POPs) such as brominated flame retardants (BFRs, specifically polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecane (HBCD)) and perfluoroalkyl acids (PFAAs, specifically perfluoroalkane sulfonate (PFOS) and perfluorooctanoic acid (PFOA)). They are used in consumer products found in cars, offices, homes and day care centers. Diet was earlier thought to be a major human exposure route for legacy POPs, but does not account for body burdens found for many new POPs and indoor exposure from air and dust has been hypothesized as also important. In this thesis, BFRs in air and dust, and PFAAs in dust from different indoor microenvironments in Sweden were analysed, and the results used to estimate human exposure. BFRs and PFAAs were detected in dust from all microenvironments and PBDEs in all air samples. BFR and PFAA exposure occurs mostly in peoples’ homes with toddlers having higher intakes from dust ingestion than adults. Inhalation and dust ingestion play minor roles compared to diet for humans with median exposures, but in worst case scenarios, dust ingestion may be significant for a small part of the Swedish population. Sampling using home vacuum cleaner bag dust and researcher-collected above floor dust was compared. Correlations were seen for ∑OctaBDE and ∑DecaBDE but not for ∑PentaBDE and HBCD. Higher PBDE concentrations were found in above floor dust but higher HBCD concentrations were found in vacuum cleaner bag dust. BDE-47 concentrations were correlated between vacuum cleaner bag dust and breast milk, indicating exposure through dust ingestion. Similar concentrations of PBDEs were measured in indoor and outgoing air from day care centers, apartment and office buildings. Indoor air explained 54-92% of ∑PentaBDE and 24-86% of BDE-209 total emissions to outdoor air in Sweden, supporting the hypothesis that the indoor environment is polluting ambient air via ventilation systems. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 2: Accepted. Paper 3: Accepted. Paper 4: Manuscript.</p>

Atomic force microscopy (AFM) is adapted to the measurement of adhesion forces between indoor-air-pollutant bioparticulates and synthetic carpet fiber materials. This novel technology is used to characterize the adhesion and release of a model bioparticulate, the bacterium E. coli on Nylon. This knowledge will lead to expanded studies of a wider range of biocontaminants, and ultimately to the ability to design carpet and rugs upholstery that reduce the spread of indoor air pollutants. Such an advance would improve life significantly for the 20+ million Americans who suffer from asthma, and countless others who are afflicted with allergies and illness spread via bioparticulates.

As building codes and green building programs require tighter home construction, the need for outdoor air ventilation to improve indoor air quality increases. Major improvements in building envelopes and duct systems have led to decreases in heating and cooling loads causing fewer HVAC system run-time hours, and increasing the probability for air stagnation within homes with poor outdoor air ventilation. ASHRAE Standard 62.2 quantifies the amount of whole-house ventilation required based on the number of occupants and the square footage of conditioned space, but leaves the design of the ventilation system up to the mechanical engineer or HVAC contractor. In 2010, ASHRAE began requiring flow testing for confirmation of outdoor air ventilation rates, yet few municipalities and green building programs have adopted the new standard. Builders in mixed-humid climates are forced to balance the need for outdoor air ventilation with the upfront costs for mechanical ventilation systems, and the potential for increased humidity loads and energy costs associated with mechanical ventilation strategies. One common solution employed in the southeastern United States involves a central fan integrated supply (CFIS) ventilation system controlled with an air-cycler for minimum run-time to meet ASHRAE Standard 62.2. While this system has been tested and proven to meet design ventilation rates, those tests were often conducted on homes constructed by well trained builders receiving strong oversight from building scientists and the design ventilation rates were not always ASHRAE compliant. The following report analyzes whether the CFIS ventilation system with air-cycler controller provides ventilation meeting ASHRAE Standard 62.2 when employed by builders with minimal training and support.

<p>In this thesis the sink-effect in indoor materials wasstudied using mathematical modelling and experimental studies.The sink-effect is a concept which is commonly used tocharacterise the ability of different indoor materials to sorbcontaminants present in the indoor air. The sorption process ismore or less reversible, i.e. molecules sorbed in materials athigh contaminant concentrations may again be desorbed at lowerconcentrations. Knowledge of the sorption capacity of materialsand the rate at which sorption and desorption takes place is offundamental importance for mathematical simulation of indoorair quality. The aim of this work is to contribute withknowledge about how the sink-effect can be described inmathematical terms and how the interaction parametersdescribing the sorption capacity and sorption/desorptionkinetics can be determined. The work has been of amethodological nature. The procedure has been to set upphysically sound mathematical models of varying complexity andto develop small-scale chamber experiments. Two differentdynamic chamber methods have been used. One is based on amodified standard FLEC-chamber while the other uses a chamberwith two compartments, one on each side of the material. The"twin-compartment" method was designed due to the observationthat the contaminant readily permeated straight through theselected materials, which resulted in uncontrolled radiallosses in the FLEC-chamber. In order to be useful forcomparison between experiments and calculations and parameterfitting, the boundary conditions in the chambers must beprecisely known and controlled. This matter has shown to be themost crucial and difficult problem in the research. A varietyof mathematical models for the sink-effect have been proposed.In some models advanced fluid simulations were used in order totest the influence ofill-defined flow boundary conditions. Theaim of the modelling is to find a formulation with a minimum ofinteraction parameters, which is generally useful, i.e. both insmall-scale laboratory environments and in full-scale like anoffice room. Estimated model parameters are shown to be able toyield a reasonably good fit to experimental data for thesorption process but a less satisfactory fit for the desorptionprocess.</p><p><b>Keywords:</b>sink-effect, sorption, adsorption, diffusion,indoor air quality, volatile organic compounds, VOC,contaminants, building materials</p>

Residential and light-commercial buildings comprise a significant portion of buildings in the United States. They account for a large fraction of the total amount of energy used in the U.S., and they also represent environments where people spend the majority of their time. Thus, the design, construction, and operation of these buildings and their systems greatly affect energy consumption and exposures to airborne pollutants of both indoor and outdoor origin. However, there remains a need to improve knowledge of some key source and removal mechanisms of indoor and outdoor pollutants in residential and light-commercial buildings, as well as their connections to energy use and peak electricity demand. Several standardized field test methods exist for characterizing energy use and indoor air quality in actual buildings, although few explicitly address residential and light-commercial buildings and they are generally limited in scope. Therefore, the work in this dissertation focuses on improving methods to characterize three particular building components for their impacts on exposures to indoor pollutants and their implications for energy consumption: (1) central forced-air heating and cooling (HAC) systems, (2) HAC filters, and (3) building envelopes. Specifically, the research in this dissertation is grouped to fulfill two primary objectives of developing and applying novel methods to: (1) characterize and evaluate central air-conditioning systems and their filters as pollutant removal devices in residential and light-commercial buildings, and to explore their implications for energy consumption, and (2) characterize and evaluate the ability of two particular outdoor pollutants of concern (ozone and particulate matter) to infiltrate indoors through leaks in building envelopes. The research in this dissertation is divided into four primary investigations that fulfill these two objectives. The first investigation (Investigation 1a) addresses Objective 1 by first providing a detailed characterization of a variety of operational characteristics measured in a sample of 17 existing central HAC systems in occupied residential and light-commercial buildings in Austin, Texas, and exploring their implications for exposure to indoor pollutants, energy use, and peak electricity demand. Among the findings in this study, central air-conditioning systems in occupied residential and light-commercial buildings did not operate most of the time, even in the hot and humid climate of Austin, Texas (i.e., ~25% of the time on average in the summer). However, average recirculation rates still make central air-conditioning systems competitive as particle removal mechanisms, given sufficient filtration efficiency. Additionally, this investigation used a larger, much broader, dataset of energy audits performed on nearly 5000 single-family homes in Austin to explore common inefficiencies in the building stock. Residential and light-commercial air-conditioning systems are often inefficient; in fact, residential central air-conditioning systems in particular likely account for nearly 20% of peak electric demand in the City of Austin. As much as 8% of peak demand could be saved by upgrading all single-family homes in Austin to higher-efficiency equipment. The second investigation (Investigation 1b) also addresses Objective 1 by developing and applying a novel test method for measuring the in-situ particle removal efficiency of HAC systems and filters in residential and light-commercial buildings. Results from the novel test method as performed with three test filters and 0.3–10 μm particles in an unoccupied test house agreed reasonably well with results from other field and laboratory test methods. Low-efficiency filters did not increase particle removal much more than simply running the HAC system without a filter, and higher-efficiency filters provided greater than ~50% removal efficiency for most particles greater than 1–2 μm in diameter. The benefit of this test method is that it can be used to measure how filters perform in actual environments, how filter removal efficiency changes with actual dust loading, and how much common HAC design and installation issues, such as low airflow rates, duct leakage, fouled coils, and filter bypass airflow, impact particle removal in real environments. The third investigation (Investigation 2a) addresses Objective 2 by developing and applying a novel test methodology for measuring the penetration of outdoor ozone, a reactive gas, through leaks in exterior building envelopes using a sample of 8 single-family residences in Austin, Texas. These measurements represent the first ever measurements of ozone penetration factors through building envelopes of which I am aware, and penetration factors were lower than the usual assumption of unity (i.e., P = 1) in seven of the eight test homes (ranging from 0.62±0.09 to 1.02±0.15), meaning that some building envelopes provide occupants with more protection from indoor exposures to ozone and ozone reaction byproducts than others. Additionally, ozone penetration factors were correlated with some building characteristics, including the amount of painted wood siding on the exterior envelope and the year of construction, suggesting that simple building details may be used to predict ozone infiltration into homes. Finally, the fourth investigation (Investigation 2b) also addresses Objective 2 by refining and applying a test methodology for measuring the penetration of ambient particulate matter through leaks in building envelopes, and using a sample of 19 single-family residences in Austin, Texas to explore correlations between experimentally-determined particle penetration factors and standardized fan pressurization air leakage tests. Penetration factors of particles 20–1000 nm in diameter ranged from 0.17±0.03 to 0.72±0.08 across 19 homes that relied solely on infiltration for ventilation air. Particle penetration factors were also significantly correlated with results from standardized fan pressurization (i.e., blower door) air leakage tests and the year of construction, suggesting that occupants of older and leakier homes are exposed to more particulate matter of outdoor origin than those in newer tighter homes. Additionally, blower door tests may actually offer some predictive ability of particle penetration factors in single-family homes, which could allow for vast improvements in making easier population exposure estimates. Overall, the work in this dissertation provides new methods and data for assessing the impacts of central air-conditioning systems, filters, and building envelopes on human exposure to indoor pollutants and energy use in residential and light-commercial buildings. Results from these four primary investigations will allow building scientists, modelers, system designers, policymakers, and health scientists to make better informed decisions and assumptions about source and removal mechanisms of indoor pollutants and their impacts on building energy consumption and peak electricity demand. / text

Poor indoor air quality in schools is associated with diminished learning, health risks to students and staff, and economic costs. This dissertation reports findings from the Texas Elementary School Indoor Air Study (TESIAS). The objective of this investigation is to establish a baseline for indoor environmental parameters. The investigation selected 30 elementary schools from 2 school districts. One school district was located along the Texas/Mexico border in a hot-humid climate region. The other school district was located in central Texas in a mixed-humid climate region. Phase I of the study was a questionnaire completed by 1336 teachers and other school staff. Phase II of the study collected both qualitative and quantitative data in 120 classrooms including continuous monitoring of comfort parameters (carbon monoxide, carbon dioxide, temperature, and relative humidity). Phase III collected more in-depth quantitative data, including fungi and bacteria concentrations, in 12 classrooms. This dissertation investigates potential differences in the study data between school districts and between portable and traditional classrooms. The two major findings of this study concern water leakage from roofs and inadequate ventilation. Roof leaks were the highest reported source of water incursion and correlated with health symptoms. Free-standing small footprint classrooms had fewer roof and wall leaks than traditional classrooms. The simple low pitch roof design and sufficient overhangs typically found on the small footprint buildings studied likely result in less reported roof leaks. The measured carbon dioxide concentrations (both average and peak values) were well in excess of the recommended maximums and fewer than 15% of the classrooms met the recommended maximum concentrations. Relatively higher CO2 concentrations and relative humidity in the border school district were attributed to a greater frequency of blocked outdoor air intakes. Further investigation of novel HVAC systems, such as low velocity displacement ventilation, is needed. Ultimately, this study enables the development of best practices for school design for improved indoor air quality. / text

Building environmental conditions such as ventilation and contaminant concentrations are important factors that influence occupant health and comfort. The objective of the present work is to investigate how personal exposure to gaseous and particulate pollutants depends on indoor airflow, source characteristics, and occupant activity in commercial and residential environments. The study examines airflow and pollutant transport using experimental measurements in conjunction with computational fluid dynamics (CFD). The results demonstrate that breathing has a measurable influence on the airflow in an occupant breathing zone, but it has very small impacts on the occupant thermal plume. The results also show that breathing can significantly affect inhaled particle concentrations, even though the influence varies with source position and particle size. Also, localized hand motions of a sitting manikin do not significantly disrupt the upward thermal plume. In typical US residences, forced convection driven mixing airflow or buoyancy driven stratified airflow occurs depending on the HVAC fan operation (fan on or fan off, respectively). The measured transition period between mixing flow (fan on) and stratified flow (fan off) is approximately one minute, implying that most airflow in the residence is either dominated by mixing or stratification. A high level of exposure to short-term pollutant sources, such as resuspension of particles from floor surfaces due to human activity, more likely occurs with stratified flow than with highly mixed airflow. This is due to the strong influence of the occupant thermal plume that transports the pollutants into the breathing zone. Furthermore, by transporting air containing ozone across the reactive occupant surface, the occupant thermal plume has a large effect on exposure to ozone reaction products. Due to the reaction of ozone with the skin oils and clothing surfaces, the occupant surface boundary layer becomes depleted of ozone and conversely enriched with ozone reaction products. The parameter ventilation effectiveness quantifies the effectiveness of airflow distribution and can be used for assessment of exposure to gaseous pollutants. Based on the study results, the usefulness of ventilation effectiveness as an indicator of exposure to particulate pollutants depends on the particle size. For small particles (~1 [mu]m), an increase of ventilation effectives caused a decrease in occupant exposure, while for large particles (~7 [mu]m), source location and airflow around the pollutant source are significant factors for the exposure, and the ventilation effectiveness has very little to no effect. / text

On November 7, 1973, President Nixon asked Americans to lower their home thermostats to a national average temperature of 68 degrees. On February 2, 1974, over half of the gas stations in the New York City area closed after selling out of fuel. These and other restrictions resulted from the Arab oil embargo of 1973-1974, a pivotal event in American history that made residential energy conservation an immediate national imperative. This dissertation situates American housing within the ecologically-oriented 1970s, when energy independence and environmental protection became political and popular priorities. I study two California communities that shared geographical and temporal proximity but responded to the energy crisis with divergent approaches to the ideal of energy-conserving, healthy housing. Part I explores early indoor environmental research at the Lawrence Berkeley Laboratory. In collaboration with utility companies, homebuilders, and homeowners, Berkeley’s researchers studied how residential energy conservation affected indoor air quality (IAQ) in conventional and alternative homes. Their goal was finding the “optimal balance” between equally vital goals: energy conservation, healthy indoor air, and cost-effectiveness. By the early 1980s, IAQ was the leading criterion in national conversations about healthy housing. Part II explores owner-built housing in 1970s California. Owner-builders embraced environmentalism and voluntary simplicity. Like Berkeley’s scientists, they pursued residential energy conservation, but did this either by living in minimalist cabins without heat or electricity,or by using alternative technologies (solar power, earth-building). Their top priority for housing was autonomy, not IAQ. They campaigned for the right to build their own low-cost housing unconstrained by building codes. They prioritized personal and planetary health in designing and building their homes, arguing that a healthy house was an instrument of social and environmental change. In juxtaposing these two approaches -- one academic and quantitative; the other holistic and iconoclastic -- I show that healthy housing has been a flexible ideal shaped by competing priorities: energy, health, affordability, and environmentalism. Housing, the fundamental link between people and the outdoor environment, is an ideal focus for environmental historians and adds another dimension to knowledge of American history since the energy crisis. / History of Science