This work covers a broad analysis of the risks that could impact the achievement of electrical safety of electrical installations. The work includes both electrical equipment such as the installation of electrical equipment.The report illustrates the main technical characteristics of electrical connections greater than 10 mm2 and provides an introduction to the crimping systems for copper and aluminum conductors. In addition to that analyzes the factors that are important to assure the quality of an electrical connection throughout the value stream in terms of both materials such informations. Furthermore analyzed deeper the need for skills development of technicians and other staff.The different parts of this work are analyzed and presented, in theory to studies carried out both at Elpress AB and partly with the help of other scientific reports dealing with similar subjects. In addition, presents a survey that will help understanding the current perception of the electrical connections and cable crimping systems among end users. Various risks are analyzed in an FMEA analysis with respect to the different stages in the value stream.The project has shown that there is a need for changes in the regulations that deals with, among other things, permission for electrical staff.

Diss. Linköping : Univ., 2001.

The thesis deals with the use of cable sections in the overhead transmission route of the 400 kV transmission system in the Czech Republic, with the design of the arrangement of the cable route and with the solution of the crossover of the cable line with other networks of the technical infrastructure or natural obstacles. The thesis shows what the construction of a 400 kV cable line in the overhead transmission route - which has not been implemented in the Czech Republic as of yet - entails in practice. The first, general part deals with the electrical properties of both the cable lines and the combined overhead transmission lines with intermediate cable sections, and this sets out limitations on the maximum possible length of the cable sections. The following chapters provide an analysis of the magnetic field of the cable line, its impact on the surrounding environment and the possibilities of its shielding. On the basis of this knowledge optimization of the designed cable route arrangement is carried out in order to make the route comply with hygiene limits. The next part uses selected locations on a real route of overhead 400 kV transmission line to show what the construction of cable sections inserted into the route of overhead 400 kV line would involve. The design includes a professional estimate of the time and financial demands of the construction.

The aim of the project was to examine the possible increase of electric power usage for electric cars with retained capacity in the electric grid of Falkenberg Energi AB. This also included identifying the fragile components in the grid. In order to examine this, a model of the grid was constructed with loads designed to mimic electric vehicle charging. The simulation generated a list showing the most stressed nodes in descending order. The results showed that there was a small number of nodes in the grid that became overloaded in certain hours of the year. The cables , on the other hand, were not overloaded at any point of the year.

No description available.

Att konstruera ett tidtagningssystem för enduro i skogen leder till flera frågor som måste undersökas och besvaras. Vilken kommunikationsteknik ska användas och vilken systemarkitekturisk lösning passar bäst? Att dra kabel ute i skogen är ett bra sätt att lösa det kommunikationstekniska problemet, lösningen är säker och relativt billig. Visst påverkas priset av distansen mellan olika klienter ute i skogen, men alla positiva egenskaper hos tekniken gör denna kostnad värd sitt pris. De geografiska variationer som kan finnas är de som kan spela ut de övriga teknikerna i form av stabilitet. En snabb resultatförmedling kräver ett system som har en väl uppbyggd systemarkitektur. Vid tidtagning kommer data i form av tider skickas från klienterna direkt till huvudservern, ingen mellanlagring sker utan data lagras centralt vilket förespråkas i IRM. Dessutom kommer ingen redundans att accepteras, vilket även det förespråkas av IRM. Det finns även flera andra parametrar som väger för att välja IRM, vilket är det som rekommenderas utifrån den analys som gjorts i denna uppsats.

Thèse 2004. / Bibliogr. Index.

This work is focused on the locating of faults of the cables laid in the ground. Firstly it describes particular types of cables and their basic physical characteristics. Following part deals with widely used methods for locating cable faults including their comparison. Than it describes DC measurements which are used to identify the type of fault. In the practical part there is a complete DC measurement on the specific cable and finding out the limits of usefulness regarding to the chosen methods for locating the failures.

This thesis gives an overview on the fault of high-voltage cable transmission lines in the distribution system of the E.ON company. The first part of this thesis introduces reader to the topic of cable transmission lines, types of commonly used cables and the most commonly occurring faults. In the second part of this thesis, the methods of locating faults in cable transmission lines by professional personnel are explained. The third part deals with the analysis of a group of chosen occurred faults. The final part focuses on the statistics of fault occurrence on South Moravian region from 1.1.2017 until 1.1.2019.

This master´s thesis deals with questions of measuring of cabling systems. There is described the evolution of structured cabling including the rules of their installation, approval and their final measurement. The first part of this work is dedicated to the conception of structured cabling and its history which originated at the beginning of 80s when the first personal computers began to appear at the market. The necessity of mutual communication of their users caused forceful development of networks and technologies. As a result lots of single-purpose, incompatible and mutual independent cabled distributions were developed. This method of cabling was uneconomical, very demanding on service and impractical for network expansion. That’s why the universal cabled system was developed whose baseline became a twisted pair. Characteristics of structured cablings are designed in order it could be possible to transmit whole rang of applications through them. Metallic cables and nowadays also optical cables are used for their installation. The cabling system consists of lots of other items among them we can rank items active and stable. It’s necessary to scale lots of criteria which involve the quality of data transmission in this network. The measurement is done by the devices which comply with basic requirements determined by the standards according to technology. There are described the rules and proper processes of installing cabling systems, which should be followed while installations. At the end of my thesis there are mentioned the results of the measurements on simulation segments of cabling system which serve as completion certificates between an installation company and a consumer.