Submitted by Lara Oliveira (lara@ufersa.edu.br) on 2017-02-14T19:11:01Z No. of bitstreams: 1 JonasOF_TESE.pdf: 3319263 bytes, checksum: 51b79bea8bd5a5a042d4db215bfe1a86 (MD5) / Approved for entry into archive by Socorro Pontes (socorrop@ufersa.edu.br) on 2017-02-15T14:50:14Z (GMT) No. of bitstreams: 1 JonasOF_TESE.pdf: 3319263 bytes, checksum: 51b79bea8bd5a5a042d4db215bfe1a86 (MD5) / Approved for entry into archive by Vanessa Christiane (referencia@ufersa.edu.br) on 2017-02-15T14:52:02Z (GMT) No. of bitstreams: 1 JonasOF_TESE.pdf: 3319263 bytes, checksum: 51b79bea8bd5a5a042d4db215bfe1a86 (MD5) / Made available in DSpace on 2017-03-21T14:53:47Z (GMT). No. of bitstreams: 1 JonasOF_TESE.pdf: 3319263 bytes, checksum: 51b79bea8bd5a5a042d4db215bfe1a86 (MD5) Previous issue date: 2016-08-29 / Sunflower adapts to different conditions of climate and soil, including the prevailing climate in the Northeast, but the water needs, as well as nitrogen fertilizer recommendations are not yet fully defined. The objective of this study was to evaluate sunflower productivity and efficiency of water and nitrogen use. The experiment was conducted between October 2013 to January 2014 in Unidade Agrícola Industrial Escola do Instituto Federal de Educação, Ciência e Tecnologia do Rio Grande do Norte (IFRN/Campus Apodi), Apodi, in the state of Rio Grande do Norte, Brazil. Statistical design used was in blocks in the 4 x 4 factorial scheme with four replications. The treatments consisted of four water slides 58, 80, 100 and 120% of crop evapotranspiration (ETc) associated with four doses of nitrogen 40, 100, 200 and 370% of the dose recommended for the cultivation of 70 kg ha-1. The depth water of 517 mm (108% ETc) associated with nitrogen dose of 77 kg ha-1 provided 91.3% of the maximum productivity, these being the doses recommended in the studied conditions. The oil productivity depending on depths water and nitrogen levels followed the trend surface function in oil yield of water depths and doses of nitrogen. The water factor was most limiting characteristics evaluated the nitrogen fertilization / O girassol se adapta a diferentes condições de clima e solo, inclusive ao clima predominante na Região Nordeste, porém, as necessidades hídricas, assim como as recomendações de adubação nitrogenada, ainda não estão perfeitamente definidas. Objetivouse com o presente estudo, avaliar a produtividade do girassol e a eficiência do uso da água e nitrogênio. O experimento foi conduzido no período de 29 outubro de 2013 a janeiro de 2014 na Unidade Agrícola Industrial Escola do Instituto Federal de Educação, Ciência e Tecnologia do Rio Grande do Norte (IFRN/Campus Apodi), Apodi, RN. O delineamento estatístico adotado foi em blocos no esquema fatorial 4 x 4 com quatro repetições. Os tratamentos consistiram em quatro lâminas de irrigação 58, 80, 100 e 120% da evapotranspiração da cultura (ETc) associadas a quatro doses de nitrogênio 40, 100, 200 e 370% da dose padrão de 70 kg ha- 1. A lâmina de água de 517 mm (108% da ETc) associada a dose nitrogenada de 77 kg ha-1 proporcionou 91,3% da produtividade máxima de grãos, sendo estas as doses recomendadas nas condições estudadas. A produtividade de óleo em função das doses de água e nitrogênio acompanhou a tendência da superfície do rendimento de óleo em função das lâminas de água e doses de nitrogênio. As lâminas de água foram mais limitantes às características avaliadas que a adubação nitrogenada / 2017-02-14

Omni-directional acoustic wave source interactions with a rough seabed with a continuously varying density and sound speed in a fluid-like sediment layer. The acoustic properties in the sediment layer possess an exponential type of variation in density and one of the three classes of sound speed profiles, which are constant,~$k^2$-linear, or inverse-square variations. Analytical solution of mean field. The mean field reflection coefficients corresponding to the aforementioned density and sound speed profiles for various frequencies, roughness parameters, are numberically generated and analyzed. Physical interpretations are provided for various results. This simple model characterizes two important features of sea floor, including seabed roughness, sediment inhomogenieties, therefore, provide a canonical analysis in seabed acoustics.

An engineering analysis of the fugitive particulate matter emissions from a feedyard is not simple. The presence of an evening dust peak in concentration measurements downwind of a feedyard complicates the calculation of an average 24-h emission flux for the feedyard. The evening dust peak is a recurring event that occurs during evening hours when particulate matter concentration measurements increase and decrease dramatically during a short period of time. The concentrations measured during the evening can be up to 8 times the concentrations measured throughout the rest of the day. There is a perception that these concentration increases are due to increases in cattle activity as the temperature decreases during the evening. The purpose of Objective 1 of this research was to quantify the changes in concentrations based on changes in meteorological conditions and/or cattle activity. Using ISCST3, a Gaussian-based EPAapproved dispersion model used to predict concentrations downwind of the feedyard , the results of this work indicate that up to 80% of the increase in concentrations can be attributed to changes in meteorological conditions (wind speed, stability class, and mixing height.)The total fugitive particulate matter emissions on a cattle feedyard are due to two sources: unpaved roads (vehicle traffic) and pen surfaces (cattle activity). Objective 2 of this research was to quantify the mass fraction of the concentration measurements that was due to unpaved road emissions (vehicle traffic). A recent finding by Wanjura et al. (2004) reported that as much as 80% of the concentrations measured after a rain event were due to unpaved road emissions. An engineering analysis of the potential of the unpaved road emissions versus the total feedyard emissions using ISCST3 suggests that it is possible for 70 to 80% of the concentration measurements to be attributed to unpaved road emissions. The purpose of Objective 3 was to demonstrate the science used by ISCST3 to predict concentrations downwind of an area source. Results from this study indicate that the ISCST3 model utilizes a form of the Gaussian line source algorithm to predict concentrations downwind of an area source.

This thesis investigates the validity of the standard thermal response test (TRT) results when performed on a series of boreholes (string). The typical TRT consists of subjecting a single borehole to a constant heat injection rate to obtain the temperature response in the ground which can then be used to determine the ground thermal conductivity. When completed on a single borehole, the results may be analyzed with the line source theory, since the assumption of a single line heat source is valid. For multiple boreholes, the assumption of a single line source becomes invalid if the spacing between the boreholes is small enough for borehole thermal interaction to occur. Moreover, for boreholes that are charged in series, heat transfer from the horizontal pipes that connect the vertical boreholes may also influence the ground thermal response. This thesis takes an in-depth look at the different factors that affect the results of TRTs performed on borehole strings. Different analysis methods are implemented to determine areas of improvement for determining the thermal conductivity of the soil surrounding the borehole string. For the analysis, the infinite line source (ILS) model and a model developed using TRNSYS 18 were used to determine the effective thermal conductivity. The results show that TRNSYS is unable to accurately model a TRT performed on a borehole string. The horizontal pipe model within TRNSYS proved to have significant fundamental issues, as the effective thermal conductivity is greatly underestimated with values of 1.2±0.1W/mK and the results of increasing the horizontal length both increased and decreased the effective thermal conductivities. The results from the ILS demonstrate that an effective thermal conductivity of 1.7±0.2W/mK is an appropriate estimate of the soil at the BTES field tested, as the borehole string with the furthest spacing between boreholes gave an effective thermal conductivity of 1.7W/mK. Performing multiple thermal response tests within the same BTES field also provided evidence of the need to implement multiple TRTs as common practise. The testing presented shows that the effective thermal conductivity can vary within ±0.2W/mK within the same relative location. With better knowledge of the thermal properties within the BTES field location comes the opportunity for improved planning of operation and control of thermal distribution within the field. This would be especially beneficial when dealing with seasonal BTES fields / Thesis / Master of Applied Science (MASc)

A road can be considered as a noise source based on its traffic density. Intuition says, a road, with closely spaced vehicles, can be classified as a line source and for sparsely spaced vehicles, a collection of point sources. This study deals with the classification of a stretch of highway into either a line source or a collection of point sources based on the sound pressure measured by 7 microphones placed at certain distances from the highway and on the law of attenuation applicable. The results indicate a strong dependence of source classification with the traffic density. / En väg kan betraktas som en bullerkälla baserat på dess trafikintensitet. Intuitivt bör en väg med hög trafikintensitet klassificeras som en linjekälla och för få fordon en samling punktkällor. Denna studie handlar om klassificeringen av en motorvägssträcka till antingen en linjekälla eller en samling punktkällor baserat på ljudtrycket uppmätt med sju mikrofoner placerade på varierande avstånd från motorvägen. Resultaten visar att källklassificeringen är beroende av trafiktätheten och av avståndet till vägen.

<p>Signal processing within the neurophysiological field is challenging and requires short processing time and reliable results. In this thesis, three main problems are considered.</p><p>First, a modified line source model for simulation of muscle action potentials (APs) is presented. It is formulated in continuous-time as a convolution of a muscle-fiber dependent transmembrane current and an electrode dependent weighting (impedance) function. In the discretization of the model, the Nyquist criterion is addressed. By applying anti-aliasing filtering, it is possible to decrease the discretization frequency while retaining the accuracy. Finite length muscle fibers are incorporated in the model through a simple transformation of the weighting function. The presented model is suitable for modeling large motor units.</p><p>Second, the possibility of discerning the individual AP components of the concentric needle electromyogram (EMG) is explored. Simulated motor unit APs (MUAPs) are prefiltered using Wiener filtering. The mean fiber concentration (MFC) and jitter are estimated from the prefiltered MUAPs. The results indicate that the assessment of the MFC may well benefit from the presented approach and that the jitter may be estimated from the concentric needle EMG with an accuracy comparable with traditional single fiber EMG.</p><p>Third, automatic, rather than manual, detection and discrimination of recorded C-fiber APs is addressed. The algorithm, detects the Aps reliably using a matched filter. Then, the detected APs are discriminated using multiple hypothesis tracking combined with Kalman filtering which identifies the APs originating from the same C-fiber. To improve the performance, an amplitude estimate is incorporated into the tracking algorithm. Several years of use show that the performance of the algorithm is excellent with minimal need for audit.</p>

Signal processing within the neurophysiological field is challenging and requires short processing time and reliable results. In this thesis, three main problems are considered. First, a modified line source model for simulation of muscle action potentials (APs) is presented. It is formulated in continuous-time as a convolution of a muscle-fiber dependent transmembrane current and an electrode dependent weighting (impedance) function. In the discretization of the model, the Nyquist criterion is addressed. By applying anti-aliasing filtering, it is possible to decrease the discretization frequency while retaining the accuracy. Finite length muscle fibers are incorporated in the model through a simple transformation of the weighting function. The presented model is suitable for modeling large motor units. Second, the possibility of discerning the individual AP components of the concentric needle electromyogram (EMG) is explored. Simulated motor unit APs (MUAPs) are prefiltered using Wiener filtering. The mean fiber concentration (MFC) and jitter are estimated from the prefiltered MUAPs. The results indicate that the assessment of the MFC may well benefit from the presented approach and that the jitter may be estimated from the concentric needle EMG with an accuracy comparable with traditional single fiber EMG. Third, automatic, rather than manual, detection and discrimination of recorded C-fiber APs is addressed. The algorithm, detects the Aps reliably using a matched filter. Then, the detected APs are discriminated using multiple hypothesis tracking combined with Kalman filtering which identifies the APs originating from the same C-fiber. To improve the performance, an amplitude estimate is incorporated into the tracking algorithm. Several years of use show that the performance of the algorithm is excellent with minimal need for audit.

The main goal of the work presented in this thesis is to improve the reliability of existing methods for speciation analysis of organotin compounds Species-specific isotope dilution (SSID) calibration in combination with gas chromatography – inductively coupled plasma mass spectrometry was used to investigate the transformation of phenyltin species during sample preparation. Isotope-enriched phenyltin species were synthesized from corresponding isotope-enriched tin metals. SSID with a mixture of phenyltin species (PhTs) from one isotope was used to evaluate different extraction procedures for the determination of PhTs in fresh water sediment. Preparative liquid chromatography was used to produce single isotope-enriched phenyltin species making a multi-isotope spike (MI) SSID calibration possible. Different extraction procedures for the analysis of phenyltin species in biological samples were evaluated by applying MI-SSID. Degradation of TPhT and DPhT during sample extraction was observed and quantified. Accurate results were therefore obtained. A sample preparation procedure using mild extraction conditions with reasonable recoveries is described. The stability of organotin standards was investigated under different storage conditions. Mono- and diphenyltin were found to be redistributed and degraded during storage in methanol but were stabilized in sodium acetate/ acetic acid. A fast redistribution between monobutyl- and diphenyl tin has been observed and therefore it is therefore recommended that standards be derivatized as soon as possible after butyl- and phenyltin standards are mixed. Included in the thesis is also an investigation of the analytical potential of using instrumentation based on atomic absorption spectrometry (AAS) for speciation analysis of organotin compounds. The method was based on gas chromatographic separation, atomization in a quartz tube and detection by line source (LS) AAS and for comparison, by state of the art continuum source (CS) AAS. Analytical performances of CSAAS system were found to be better compared to LSAAS.

The thermal response of a borehole field is often described by non‐dimensional response factors called gfunctions.The g‐function was firstly generated as a numerical solution based on SBM (Superposition BoreholeModel). An analytical approach, the FLS (Finite Line Source), is also accepted for generating the g‐function. In thiswork the potential to numerically produce g‐functions is studied for circular borehole fields using the commercialsoftware COMSOL. The numerical method is flexible and allows the generation of g‐functions for any boreholefield geometry. The approach is partially validated by comparing the solution for a square borehole field containing36 boreholes (6x6) with g‐functions generated with the FLS approach and with the program EED (Earth EnergyDesigner). The latter is based on Eskilsons SBM, one of the first documents where the concept of g‐functions wasintroduced. Once the approach is validated, the square COMSOL model is compared with a circular geometryborehole field developed by the same method, consisting of 3 concentric rings having 6, 12, and 18 boreholes.Finally the influence on the circular geometry g‐function is studied when connecting the boreholes in radial zoneswith different thermal loads. / Den termiska responsen för ett borrhålsfält beskrivs ofta med den dimensionslösa responsfunktionen kallad gfunktion.Responsfunktionen togs först fram som en numerisk lösning med SBM (Superposition Borehole Model).En analytisk metod, FLS (Finite Line Source) är också accepterad för framtagandet av g‐funktioner. I det här arbetetundersöks förutsättningarna att numeriskt ta fram g‐funktioner för cirkulära borrhålsfält genom att använda detkommersiella simuleringsprogrammet COMSOL Multiphysics. Den numeriska metoden är flexibel och kananvändas för alla typer av borrhålsgeometrier. Metoden att använda COMSOL valideras delvis genom att jämföraresultatet för ett kvadratiskt borrhålsfält innehållande 36 borrhål (6x6) med lösningar framtagna med FLS och meddimensioneringsprogrammet EED (Earth Energy Designer). Det senare har sin grund i Eskilsons SBM, ett av deförsta arbeten där begreppet g‐funktion introducerades. När metoden att använda COMSOL verifierats, jämförsden kvadratiska borrhålsmodellen med en cirkulär borrhålskonfiguration, upprättad med samma metod,innehållande 3 koncentriska ringar om vardera 6, 12, 18 borrhål. Slutligen undersöks hur den termiska responsenpåverkas då borrhålen i ett cirkulärt borrhålsfält kopplas samman och grupperas i radiella zoner med olika termiskalaster. / SEEC Scandinavian Energy Efficiency Co.