Spelling suggestions: "subject:"wow aprofile"" "subject:"wow eprofile""
1 |
Research and Development of Low-Profile, Small Footprint Antennas for VHF-UHF Range ApplicationsOlaode, Olusola January 2012 (has links)
<p>Efficient, but low-profile and small-footprint antennas for VHF-UHF range applications remains an ongoing work. VHF range spans approximately 54 - 88 MHz while UHF roughly ranges from 174 - 890 MHz. The inverse relationship between the physical length and resonant frequency of an antenna, which is a measure of its operating frequency range, is well known. A direct correlation between an antenna's physical length and radiation efficiency has also been established. Therefore, a combination of these constraints complicates the design of low-frequency antennas that have small physical size but with enough radiation resistance to be an efficient radiator when connected to a source having a comparable resistance. Given the frequency bands above, their corresponding wavelengths will be: 3.4-5.5 m (VHF) and 0.3-1.7 m (UHF). The length of an antenna operating at these wavelengths would need to be electrically-small i.e. a fraction of wavelength given size constraints for applications such as defense or commercial mobile communication equipment. As a consequence, the radiation resistance of the antenna, which is a function of its radiation efficiency, is greatly reduced. In other words, the input impedance or radiation impedance (assuming negligible ohmic losses in the antenna structure) features a small resistive component and a large capacitive component, causing reflections of most of the incident power to the antenna. Highly-reactive antennas are not desired for most transmitters and receivers. Therefore, the radiation resistance of an antenna must be increased by increasing its electrical length while simultaneously maintaining a low profile and footprint. This aim can be achieved by configuring the antenna to excite a resonance at, or very close to a desired operating frequency. An approach that I will explore in this dissertation is to exploit the broadband characteristics of meander-line and helical (or "spiral") antennas typically applied in the microwave frequency range to the UHF-VHF range. I will also propose novel antenna geometries that combine spiral and meander-line properties and analyze their performance. These antennas offer significant size reductions; for example, a bowtie meander dipole antenna studied yielded a height reduction of 55% at 64 MHz relative to a half-wave dipole antenna of the same resonant frequency. In addition, I will present a set of equations developed for predicting the fundamental resonant frequency and radiation resistance of meander-line antennas.</p> / Dissertation
|
2 |
Analysis, Design and Measurements of Flat and Curved Circularly Symmetric High Impedance Surfaces for Curvilinear Antenna ApplicationsJanuary 2018 (has links)
abstract: In this dissertation a new wideband circular HIS is proposed. The circular periodicity made it possible to illuminate the surface with a cylindrical TEMz wave and; a novel technique is utilized to make it wideband. Two models are developed to analyze the
reflection characteristics of the proposed HIS.
The circularly symmetric high impedance surface is used as a ground plane for the design of a low-profile loop and spiral radiating elements. It is shown that a HIS with circular periodicity provides a wider operational bandwidth for curvilinear radiating elements such, such as loops and spirals, compared to canonical rectangular HISs.
It is also observed that, with the aid of a circular HIS ground plane the gain of a loop and a spiral increases compared to when a perfect magnetic conductor (PMC) or rectangular HIS is used as a ground plane. The circular HIS was fabricated and the loop and spiral elements were placed individually in close proximity to it.
Also, due to the growing demand for low-radar signature (RCS) antennas for advanced airborne vehicles, curved and flexible HIS ground planes, which meet both the aerodynamic and low RCS requirements, have recently become popular candidates within the antenna and microwave technology. This encouraged us, to propose a spherical HIS where a 2-D curvature is introduced to the previously designed flat HIS.
The major problem associated with spherical HIS is the impact of the curvature on its reflection properties. After characterization of the flat circular HIS, which is addressed in the first part of this dissertation, a spherical curvature is introduced to the flat circular HIS and its impact on the reflection properties was examined when it was illuminated with the same cylindrical TEMz wave. The same technique, as for the flat HIS ground plane, is utilized to make the spherical HIS wideband. A loop and spiral element were placed in the vicinity of the curved HIS and their performanceswere investigated. The HISs were also fabricated and measurements were conducted to verify the simulations. An excellent agreement was observed. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2018
|
3 |
Investigation of Low Profile Antenna Designs for Use in Hand-Held RadiosGobien, Andrew Timothy III 07 August 1997 (has links)
Antennas in hand-held radios must be compact and unobtrusive. Electrically small and low-profile antennas experience high input reactance, low input resistance, and low radiation efficiency.Further degradation of radiation efficiency occurs in hand-held radios due to size-reduced ground planes, losses within the plastic device casing, and losses due to coupling with the tissue of the user. These factors may also affect the radiation pattern of the antenna.
This discussion reports on antenna designs that are well suited for hand-held radios. The design issues are covered for electrically small antennas and the hand-held environment. A review of Microstrip Antenna (MSA) theory, and the theory of the Inverted-L Antenna (ILA), and variations on the ILA including the Inverted-F Antenna (IFA), Planar Inverted-F Antenna (PIFA), and Dual Inverted-F Antenna (DIFA) is included. Two specific antenna designs are presented: the DIFA and the Proximity-Coupled Rectangular Patch MSA. The radiation patterns and input impedance of the DIFA are calculated numerically and measured empirically. The Proximity-Coupled Rectangular Patch Microstrip Antenna is treated numerically. / Master of Science
|
4 |
A Comprehensive Investigation of New Planar Wideband AntennasSuh, Seong-Youp 28 August 2002 (has links)
Broadband wireless communications require wideband antennas to support large number of users and higher data rates. Desirable features of a wideband antenna are low-profile, dual-polarization and wide bandwidth in a compact size. Many existing wideband antennas are large in size and some have only circular polarization. On the other hand low-profile, dual-polarized antennas frequently have limited bandwidth. This dissertation reports on results from original research into several new wideband antennas. All are compact and planar, and many are low-profile and dual-polarized.
Since 1994, Virginia Tech Antenna Group (VTAG) has performed research on the wideband, low-profile and dual-polarized antennas of compact size. This research resulted in the following antenna innovations: the Fourpoint, Fourtear, PICA (Planar Inverted Cone Antenna), diPICA (dipole PICA) and LPdiPICA (Low-Profile diPICA) antennas. They are all planar in geometry so one can easily construct them in a compact size. The antennas were characterized and investigated with extensive simulations and measurements. The computed and measured data demonstrates that some of the antennas appear to have the characteristics of the self-complementary antenna and most of the proposed antennas provide more than a 10:1 impedance bandwidth for a VSWR < 2. Patterns, however, are degraded at the high end of the frequency. Several tapered ground planes were proposed to improve the radiation pattern characteristics without degrading the impedance performance. A simulation result proposed a possibility of another antenna inventions providing 10:1 pattern bandwidth with the 10:1 impedance bandwidth.
Research into wideband antennas demonstrated that the newly invented antennas are closely related each other and are evolved from a primitive element, PICA. Not only the comprehensive investigation but also a practical antenna design has been done for commercial base-station array antennas and to phased array antennas for government applications. This dissertation presents results of comprehensive investigation of new planar wideband antennas and its usefulness to the broadband wireless communications. / Ph. D.
|
5 |
A Thin Flat Antenna Design for Third Generation Mobile Communication SystemsChen, An-chia 06 June 2004 (has links)
By employing a low-cost loop antenna of simple structure, a novel antenna design to efficiently make use of the system ground plane of a PDA (personal digital assistant) is proposed. Owing to a small distance of 3 mm between the antenna and the ground plane, the propose antenna has a very low profile. By selecting a proper loop¡¦s length-to-width ratio, two resonant modes close to each other can be excited, which lead to an impedance bandwidth of 17%. In addition, because of the same direction of the surface currents on the radiating metal plate, the antenna peak gain reaches about 4.5 dBi, which is attractive for application in PDAs.
|
6 |
Design and optimization of broadband planar baluns and dipole antennasMelais, Sergio E. 01 January 2005 (has links)
The effective output balancing capability of this balun is proven by the close agreement between the measured and simulated results. Diode detectors are nonlinear devices used for extraction of DC from free space transmission, achieving RF to DC conversion. Detectors are of popular use today in RF-ID tags, virtual batteries, power scavenging, and many other portable applications. The dominating factor on the performance for this device is responsivity (mV/mW), which depends on the input matching, and in the relation of power level to input impedance. Here, an accurate comparison between model measured detectors has been accomplished, and a sensitivity study has been applied to the input impedance to represent variations in responsivity due to input mismatch.At last an End-Loaded Planar Open-Sleeve Dipole (ELPOSD) is realized resulting on a printed dipole structure offering broadband response.
|
7 |
High-Directive Metasurface Printed Antennas for Low-Profile ApplicationsJanuary 2020 (has links)
abstract: Since the advent of High Impedance Surfaces (HISs) and metasurfaces, researchers
have proposed many low profile antenna configurations. HISs possess in-phase reflection, which reinforces the radiation, and enhances the directivity and matching bandwidth of radiating elements. Most of the proposed dipole and loop element designs that have used HISs as a ground plane, have attained a maximum directivity of 8 dBi. While HISs are more attractive ground planes for low profile antennas, these HISs result in a low directivity as compared to PEC ground planes. Various studies have shown that Perfect Electric Conductor (PEC) ground planes are capable of achieving higher directivity, at the expense of matching efficiency, when the spacing
between the radiating element and the PEC ground plane is less than 0.25 lambda. To establish an efficient ground plane for low profile applications, PEC (Perfect Electric Conductor) and PMC (Perfect Magnetic Conductor) ground planes are examined in the vicinity of electric and magnetic radiating elements. The limitation of the two ground planes, in terms of radiation efficiency and the impedance matching, are discussed. Far-field analytical formulations are derived and the results are compared with full-wave EM simulations performed using the High-Frequency Structure Simulator (HFSS). Based on PEC and PMC designs, two engineered ground planes are proposed.
The designed ground planes depend on two metasurface properties; namely in-phase reflection and excitation of surface waves. Two ground plane geometries are considered. The first one is designed for a circular loop radiating element, which utilizes a
circular HIS ring deployed on a circular ground plane. The integration of the loop element with the circular HIS ground plane enhances the maximum directivity up to 10.5 dB with a 13% fractional bandwidth. The second ground plane is designed for a square loop radiating element. Unlike the first design, rectangular HIS patches are utilized to control the excitation of surface waves in the principal planes. The final design operates from 3.8 to 5 GHz (27% fractional bandwidth) with a stable broadside maximum realized gain up to 11.9 dBi. To verify the proposed designs, a prototype was fabricated and measurements were conducted. A good agreement between simulations and measurements was observed. Furthermore, multiple square ring elements are embedded within the periodic patches to form a surface wave planar antenna array. Linear and circular polarizations are proposed and compared to a conventional square ring array. The implementation of periodic patches results in a better matching bandwidth and higher broadside gain compared to a conventional array. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2020
|
8 |
Uniform Field Distribution Using Distributed Magnetic StructureKeezhanatham Seshadri, Jayashree 13 January 2014 (has links)
Energy distribution in a conventional magnetic component is generally not at a designer's disposal. In a conventional toroidal inductor, the energy density is inversely proportional to the square of the radius. Thus, a designer would be unable to prescribe uniform field distribution to fully utilize the inductor volume for storing magnetic energy.
To address this problem a new inductor design, called a "constant-flux" inductor, is introduced in this thesis. This new inductor has the core and windings configured to distribute the magnetic flux and energy relatively uniformly throughout the core volume to achieve power density higher than that of a conventional toroidal inductor. The core of this new inductor design is made of concentric cells of magnetic material, and the windings are wound in the gaps between the cells. This structure is designed to avoid crowding of the flux, thus ensuring lower core energy losses. In addition, the windings are patterned for shorter length and larger area of cross-section to facilitate lower winding energy losses.
Based on this approach, a set of new, constant flux inductor/transformer designs has been developed. This design set is based on specific input parameters are presented in this thesis. These parameters include the required inductance, peak and rms current, frequency of operation, permissible dc resistance, material properties of the core such as relative permeability, maximum permissible magnetic flux density for the allowed core loss, and Steinmetz parameters to compute the core loss. For each constant flux inductor/transformer design, the winding loss and core loss of the magnetic components are computed. In addition, the quality factor is used as the deciding criterion for selection of an optimized inductor/transformer design.
The first design presented in this thesis shows that for the same maximum magnetic field intensity, height, total stored energy, and material, the footprint area of the new five-cell constant-flux inductor is 1.65 times less than that of an equivalent conventional toroidal inductor. The winding loss for the new inductor is at least 10% smaller, and core loss is at least 1% smaller than that in conventional inductors. For higher energy densities and taller inductors, an optimal field ratio of the dimensions of each cell (α = Rimin/Rimax) and a larger number of cells is desired. However, there is a practical difficulty in realizing this structure with a larger number of cells and higher field ratio α. To address this problem, an inductor design is presented that has a footprint area of a three-cell constant-flux inductor (α = 0.6) that is 1.48 times smaller in comparison to an equivalent conventional toroidal inductor. For the same maximum magnetic flux density, height, material, and winding loss, the energy stored in this new three-cell constant-flux inductor (α = 0.6) is four times larger than that of an equivalent conventional toroidal inductor.
Finally, new designs for application-specific toroidal inductors are presented in this thesis. First, a constant-flux inductor is designed for high-current, high-power applications. An equivalent constant-flux inductor to a commercially available inductor (E70340-010) was designed. The height of this equivalent inductor is 20% less than the commercial product with the same inductance and dc resistance. Second, a constant-flux inductor design of inductance 1.2 µH was fabricated using Micrometal-8 for the core and flat wire of 0.97 mm x 0.25 mm for the conductor. The core material of this inductor has relative permeability < 28 and maximum allowed flux density of 3600 Gauss. The dc resistance of this new, constant flux inductor was measured to be 14.4 mΩ. / Master of Science
|
9 |
DEVELOPMENT OF AN ULTRA-WIDEBAND LOW-PROFILE WIDE SCAN ANGLE PHASED ARRAY ANTENNAVo, Henry Hoang 01 October 2015 (has links)
No description available.
|
10 |
Analysis of a corrugated metal box type culvertOh, Saekyung January 1989 (has links)
No description available.
|
Page generated in 0.0527 seconds