The influence of microstructure on the corrosion behaviour of magnesium alloys has been investigated using advanced microscopy approaches including optical microscopy, SEM, TEM and SKPFM with a focus on the effect of melt-conditioned twin roll casting (MCTRC) and friction stir welding (FSW) on the resultant microstructure of magnesium alloys.The microstructure characterization revealed that intense shearing, generated through the advanced shear technology, resulted in grain refinement and a uniform distribution of the β-phase and reduced micro-porosity in the MCTRC Mg-Al alloys, of which were attributed to the enhanced heterogeneous nucleation, which resulted in a highly refined grain structure. The TRC Mg-Al alloys displayed a coarse grained microstructure, with a random distribution of grain sizes. Deformation features like twinning, localized shear, microporosity and centre-line segregation were some of the commonly observed defects in the TRC alloys. The general microstructure of the AZ series Mg-Al alloys was composed of α-Mg grains, the β-phase, rosette-shaped Al8Mn5 intermetallic particles and β-precipitates.The MCTRC Mg-Al alloys showed improved corrosion resistance owing to the reduced grain size and the β-phase network acting as a corrosion barrier, thereby retarding the corrosion process. The TRC Mg-Al alloys exhibited higher susceptibility to galvanic corrosion due to the coarse and random distribution of grain sizes, and segregation. The corrosion testing results showed different corrosion morphologies, including filiform-like and spherical channel-like along with overall general corrosion. However, galvanic corrosion, initiating at localized sites due to Al8Mn5 intermetallic particles and the Si/Fe impurities accounted for a major deterioration in the performance of the Mg-Al alloys. The polarization curves revealed no evidence of passivation, suggesting that the alloy surface was continuously attacked. SKPFM results indicated that the micro-constituents, namely Al8Mn5 intermetallic particles and the β-phase exhibited higher nobility relative to the α-Mg matrix, suggesting formation of micro-galvanic couples at localized sites leading to the initiation of galvanic corrosion.The AM60 and AZ91 Mg-Al alloys, subjected to FSW, revealed that the traverse speed had a direct influence on the weld zone microstructure, where the size of the friction stir/weld nugget zone decreased with increase in the traverse speed and the increase in the rate of deformation, led to widening of the friction stir zone, below the shoulder. The weld microstructure displayed a prominent friction stir zone, with an ultrafine grain structure of an average grain size ranging from 2-10 μm. The localized increase in temperatures, in the TMAZ, due to the lower tool rotation rates and traverse speeds, which rise above the eutectic melting point (430°C), showed evidence of partial melting followed by re-solidification of the β-phase and evidence of liquation below the shoulder regions in the TMAZ. The morphology of the β-phase clearly revealed solute segregation, inconsistent with the β-phase observed in the parent alloy microstructure.The polarization curves obtained from the weld zones in the FSW AM60 alloy showed an improved corrosion resistance compared with the parent metal zone. SKPFM results revealed that the α-Mg matrix in the friction stir zone showed higher surface potential values compared with the parent alloy microstructure, due to the dissolution of the β-phase, suggesting higher nobility. However, the polarization behaviour of the AZ91 alloys did not show a significant difference in the corrosion resistance in the weld zones due to the higher volume fraction of the β-phase in the AZ91 alloys. The immersion testing results revealed higher susceptibility to corrosion in the transition zone due to the flash formation and the banded microstructure leading to failure of the weld zone.

Magnesium and its alloys are considered as the potential biomaterials due to their biocompatibility and biodegradable characteristics but suffer from poor corrosion performance. Various surface modification techniques are employed to improve their corrosion resistance. In present case, laser surface melting was carried out on AZ31B Mg alloy with various laser energy densities using a continuous wave ytterbium laser. Effect of laser treatment on phase and microstructure evolution was evaluated by X ray diffraction and scanning electron microscopy. Multi-physics thermal model predicted time temperature evolution along the depth of the laser treatment zone. Additionally, electrochemical method and bio-immersion test were employed to evaluate the corrosion behavior in simulated body fluid medium. Microstructure revealed grain refinement and even distribution of Mg17Al12 phase along the grain boundary for laser treated samples leading to substantial enhancement in the corrosion resistance of the laser treated samples compared to the untreated alloy. The laser processed samples also possessed a superior wettability in SBF solution than the untreated sample. This was further reflected in enhanced bio-integration behavior of laser processed samples. By changing the parameters of laser processing such as power, scanning speed, and fill spacing, a controllable corrosion resistance and bioactivity/biocompatibility of the implant material was achieved.

Dilute Mg alloys are exclusively identified for wrought structural applications in automotive industry. Any improvement in mechanical properties of alloys is possible only by grain size refinement and by the development of suitable texture. The grain size, grain size anisotropy and texture in these alloys affect the compatibility stresses in a very complex manner. To launch a full scale study towards understanding the complex deformation mechanisms operating in these alloys, it is necessary to understand the effect of grain size and texture on the mechanical behavior of Mg alloys in a broad or semi-quantitative manner first. Current literature lacks such broad study. In this present study, the effect of grain size, grain size anisotropy and texture evolution on the mechanical properties are examined in order to develop an understanding of the deformation mechanism that control the mechanical properties of a dilute conventionally extruded Mg alloy, AZ21. The approach adopted was to first study the microstructure and texture evolution in this conventionally extruded alloy. Since the grain sizes in these alloys vary over a wide range, it is hence necessary to study the microstructure evolution in a highly quantitative manner. In understanding texture, the present study is only limited to qualitatively evaluating the evolution of fibre component of texture using X-Ray Diffraction spectra. For truly quantitative microstructure evolution results in materials were grains sizes are spread over a wide range, it is critical to study a statistically enough no. of grains. Hence to avoid any sampling error, large montages (about 0.3 sq. mm) were constructed out of a series of high resolution images captured using an optical microscope. The montages so constructed are subjected to extensive image enhancement and various other operations are performed to convert these coloured to binary montages. Information like grain size, diameter etc., can be easily extracted from these binary montages and used for further analysis. Fibre texture in these conventionally extruded dilute Mg alloys generally develops due to alignment of basal planes along the direction of extrusion. The Critical Resolved Shear Stress for basal slip is very low when compared to that of non-basal planes. And also since there are very limited primary slip systems in these dilute Mg alloys, the development of strong fibre texture drastically changes the compatibility stresses and hence the mechanical properties . To broadly study the effect of microstructure-texture on mechanical proerties, after post extrusion annealing, heat treatments representing typical microstructure-texture combinations were identified. Effect of each microstructure-texture combination on the tensile and completely reversed cyclic fatigue properties are studied and qualitatively interpreted. The fibre texture showed pronounced effect on tensile ductility but it hardly affected the yield strength. With just 10% reduction in BPI, the ductility reduced by about 50%. A small change in average grain size did not alter the yield strength. Unlike tensile ductility, fatigue endurance stress was not altered drastically by the change in grain size or texture. But there appeared to be a significant effect of residual stress. In ending, a small change in microstructure-texture combination in these conventionally extruded alloys has a pronounced effect on ductility or in other words plastic properties. But a it has minimal effect on yield strength and fatigue endurance stress.

Two magnesium alloys (Mg-4Y-4Gd-2Ca and Mg-2Y-2Gd-1Ca) with high ignition tem- perature were successfully processed by extrusion. Mg-2Y-2Gd-1Ca alloy was addition- ally processed by equal channel angular pressing (ECAP) to achieve ultrafine-grained microstructure. The effect of extrusion parameters on fraction of recrystallized grains, grain size, and texture was revealed by EBSD analysis. The presence of Mg2Ca, REH2 and Mg5RE secondary phases was proven by SEM and TEM. Microstructural condition including distribution and morphology of secondary phase par- ticles directly affected the mechanical properties. Yield tensile stress exceeding 200 MPa was achieved in each condition. Large non-recrystallized grains with strong {10̄10} tex- ture resulted in a significant anisotropy in mechanical properties. Processing by ECAP led to a homogeneous microstructure with a mean grain size below 1 µm. ECAP condition showed superior mechanical properties with a low anisotropy. The developed and analysed microstructural condition resulted in favourable mechanical properties. The studied alloys are therefore promising for the application in aerospace industry. 1

Aim of the present work was to explore the possibility of improving strength of cast Mg by alloying additions, viz., Si and Zn+Al. All the alloys were produced by squeeze casting technique using squeeze pressure of 12MPa and their microstructure, tensile and corrosion properties were studied. Mg-Si system was chosen because the intermetallic compound Mg2Si possesses many desirable properties, such as, low density, high hardness, high melting point. Hence, there is scope for improving the strength of Mg by dispersion of primary Mg2Si particles. Addition of Si to Mg resulted in the formation of �-Mg, particles of primary Mg2Si and eutectic as microstructural constituents. The morphology of primary Mg2Si changed from polyhedral shaped particles to dendrites as Si content was increased from 3.57 to 5.5 wt%. Volume fraction of primary Mg2Si increased with increase in Si content. Particle size of primary Mg2Si also increased with increase in silicon content but at the same time it was found to be dependent on melt temperature, i.e., a lower particle size was obtained at higher melt temperatures. Addition of Al and Sr was made to Mg-2Si alloy in order to further increase the strength by solid solution strengthening and refinement/modification of primary Mg2Si particles/eutectic. Addition of 1.2 wt% Al to Mg-2Si alloy resulted in irregular type of morphology of Mg2Si particles and increased particle size. Addition of 0.2 wt% SrtoMg-2Si-1.2Al alloy resulted in slight refinement of primary Mg2Si particles and modification of eutectic. Addition of 0.4 wt% Sr resulted in both refinement and restoration of morphology of Mg2Si particles from irregular to polyhedral shape. This was accompanied by destruction of eutectic, and rods containing Mg, Si, Al and Sr were observed. The addition of 1.33 wt%Si to Mg resulted in improvement in 0.2%PS by about 80 MPa,UTS by about 40MPa and these values did not change much till the addition of 3.57 wt% Si. A drop in the strength values was observed at Si content of 5.5 wt%,where transition in morphology of primary Mg2Si occurred from polyhedral to dendrite. Addition of Si resulted in reduction in % elongation by about 2%. The addition of Al and Sr did not change the tensile properties of binary Mg-2Si alloy much. It was concluded that the volume fraction and size of primary Mg2Siparticles obtained with Si addition up to 3.57 wt% did not contribute much to strength and the strengthening mainly came from the eutectic present in the matrix. As Si content was increased to 5.5 wt% in order to increase the volume fraction of primary Mg2Si particles, the morphology of Mg2Si changed to dendritic type resulting in reduction in strength. Thus, the maximum increase in strength is achieved at near eutectic composition,i.e.,intheMg-1.33Sialloy,andfurtherincreaseinstrengthdoesnotseem to be feasible with this alloy system. The ductility of all the Mg-Si based alloys was also low, i.e, 0.5% elongation to fracture or less. Regarding the corrosion behaviour, the addition of Si to Mg deteriorated the corrosion resistance and the addition of Al and Sr further worsened it. Since further improvement in tensile properties did not seem feasible with Mg-Si alloy system, the focus was shifted to Mg-Zn-Al alloy system. There is scope for improvement in strength in Mg-Zn-Al alloy system by solid solution strengthening, grain refinement and precipitation hardening. It was observed that the addition of Zn and Al resulted in microstructure containing α-Mg grains and secondary phase at the grain boundary. XRD analysis showed the secondary phase to be Al5Mg11Zn4 but EDS analysis did not match with this composition. Therefore, the nature of this phase remains uncertain. Addition of 6 wt% Zn and 1 wt% Al resulted in improvement in strength as well as ductility: 0.2%PS improved by about 70 MPa, UTS by about 100 MPa and % elongation by about 7%. Addition of small amounts of Caresultedinrefinementofmicrostructurecausingimprovementinstrengthwithout much decrease in % elongation. Increase in Al content from 1 to 4 wt% resulted in increase in 0.2%PS but UTS slightly decreased, as % elongation reduced. Alloys subjected to T6 heat treatment showed improvement in strength but slight reduction in % elongation. ZA64 alloy in T6 condition gave 130 MPa 0.2%PS, 225 MPa UTS and 4.9% elongation, which are much higher tensile properties as compared Mg-Si alloys. All the three mechanisms mentioned above contribute to the strengthening. There is scope for further improvement in strength by employing a more suitable heat treatment. Regarding corrosion behaviour, addition of 6 wt% Zn and 1 wt% of Al to Mg did not deteriorate its corrosion resistance much. Addition of small amounts of Ca was found to be beneficial for corrosion resistance, whereas an increase in Al content lowered the corrosion resistance. Heat treatment also reduced the corrosion resistance.