Made available in DSpace on 2014-10-09T12:46:42Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:56:09Z (GMT). No. of bitstreams: 1 07613.pdf: 5555459 bytes, checksum: 0047c9f052248797761d648268e841ba (MD5) / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2015-07-23T11:12:14Z No. of bitstreams: 0 / Made available in DSpace on 2015-07-23T11:12:14Z (GMT). No. of bitstreams: 0 / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Selective laser melting (SLM) of metallic powders is an additive manufacturing technique that is widely employed to produce 3D components, and is fast becoming an important method for manufacturing near-net shape and complex metallic parts. In this thesis, a comprehensive investigation on the effect of SLM on the mechanical and corrosion properties of the Al-12Si (AS), 316L stainless steel (SS), and 18(Ni)-300 grade managing steel (MS) is investigated, with particular emphasis on the developing (micro- as well as mesa-)structure -property correlations. Detailed microstructural characterization combined with quasi-static tensile, fracture toughness, fatigue crack growth, and unmatched fatigue tests were conducted. The effect of post-SLM heat treatment as well as the scanning strategy (linear vs. checker board hatch style) was examined and the results are compared with those of conventionally manufactured (CM) counterparts. The SLM alloys exhibit a mesostructured, in addition to the fine cellular structure along the boundaries. In a case of SLM-AS, the fine cellular structure imparts higher strength at the cost of ductility, while the mesostructured, which arises due to the laser track hatching, causes the crack path to be tortuous, and in turn leads to substantial increase in fracture toughness. This imparts significant anisotropy to the toughness while tensile properties are nearly-isotropic. The experimental results of SLM-SS also show that higher tensile strengths properties with a marked reduction ductility. In spite of these, the fracture toughness, which ranges between 63 and 87 MPa.m0.5, of the SLM-SS is good, which is a result of the mesostructured induced crack tortuousity.Both tensile and toughness properties of SLM-SS were found to be anisotropic in nature. Upon aging SLM-MS, nanoscale precipitation of intermetallic compounds occurs within the cells that, in turn, lead in marked improvements in tensile strengths properties, but substantial reductions in ductility and fracture toughness. Overall, the mechanical performance, except ductility, of the SLM-MS after aging is found to be similar to that of CM-MS. Importantly, the lack of ductility does not lead to a reduction in toughness. Although the SLM-MS alloy possesses a mesostructured, no significant anisotropy in the mechanical behaviour is observed. The unnoticed studies on SLM-AS, -SS, and -MS reveal that the tensile residual stresses, gas-pores, and unmelted powder particles, can degrade the unmatched highest fatigue properties considerably and hence need be eliminated for high fatigue strength. Room temperature, electrochemical corrosion resistances (CRs) of SLM-AS, -SS and -MS in 0.1M NaCl solution were also evaluated and compared with those CM counterparts. While SLM improves CRs of AS and SS, it degrades that of MS. The results are discussed in terms of microstructural refinement and porosity that are common in SLM alloys.

Made available in DSpace on 2014-10-09T12:46:42Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:56:09Z (GMT). No. of bitstreams: 1 07613.pdf: 5555459 bytes, checksum: 0047c9f052248797761d648268e841ba (MD5) / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2015-07-23T11:12:14Z No. of bitstreams: 0 / Made available in DSpace on 2015-07-23T11:12:14Z (GMT). No. of bitstreams: 0 / Neste trabalho estudou-se as propriedades obtidas em juntas soldadas pelo processo de soldagem a laser do tipo estado sólido de onda contínua guiado por fibra, e os resultados foram comparados com juntas soldadas pelo processo feixe de elétrons. O material utilizado foi o aço maraging 350 - ASTM A 538 Grade C. As soldas realizadas com o processo feixe de elétrons possuem um procedimento de soldagem aprovado. A junta selecionada para a elaboração do trabalho foi do tipo sobreposta com material de base de espessuras diferentes, respectivamente iguais a 1,00 e 0,78 mm. As juntas soldadas foram avaliadas por: ensaio de cisalhamento, dureza Vickers e caracterização microestrutural das diversas regiões das juntas soldadas. Foram realizadas análises por microscopia óptica e microscopia eletrônica de varredura usando espectrometria de energia dispersiva (MEV/EDS). Foi realizado o teste de hipótese como técnica para a análise dos dados provenientes dos ensaios experimentais. Nas juntas soldadas com ambos processos não foi verificada a presença de descontinuidades, poros e depressões na superfície do cordão. Os resultados indicam que as condições usadas em ambos os processos de soldagem foram satisfatórias e possibilitaram a soldagem do aço maraging 350 atendendo aos requisitos necessários. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Atlas Copco Secoroc AB are searching after new bulk materials for drill heads that are used in percussive drilling in order to improve their strength and durability. The aim of this project is to assist Atlas Copco in this search and provide them with further information regarding material properties, alloying elements, suppliers, etc. A literary study was carried out in order to identify materials that had UTS and KIC more than or equal to 1700 MPa and 70 MPa*m^1/2, respectively. Materials that fulfilled these criteria were T250 grade maraging steel, Cobalt free maraging steel, High cobalt maraging steel, 300 grade maraging steel, AerMet 100, AF1410, S53, M54, 300M, 4340M and PremoMet. These were categorized into maraging steels, high alloy secondary hardened steels, and low alloy steels, and were then further researched. The material with the highest combination of UTS and KIC was M54 followed by AerMet 100; while AF1410 had the highest KIC but a low UTS, and PremoMet had the highest UTS but a low KIC. Maraging steels and HASH steels have a similar price range, while low alloy steels are much cheaper.

This diploma thesis deals with development and design modifications of tire mould segment which will be batch produced by additive technology Selective Laser Melting. Material for its production is maraging steel 1.2709. Lattice structure was used inside the segment construction. The geometry of the lattice cell was chose based on two main factors – eliminating production costs and providing sufficient stiffness. Strength of the segment was calculated by FEM. The functional sample was made and its distortion was analyzed by optical digitalization.

Over the last decade, the application of ultra-high strength steel as safety components and structural reinforcements in automobile applications has increased due to their favourable high-strength-to-weight ratio. The complex shaped components are widely produced using hot stamping. However, this process encounters problems such as galling and increased wear of the tools due to harsh operating conditions associated to the elevated temperatures. Moreover, quenching is a critical step that affects the hot formed components. Slow cooling rates results in inhomogeneous mechanical properties and increased cycle time. Therefore, fast and homogeneous quenching of the formed components in combination with reduction of wear rates during hot forming are important targets to ensure the quality and efficiency of the process. The use of additive manufacturing (AM) technologies opens up potential solutions for novel tooling concepts. The manufacturing of complex shape cooling channels and integration of high-performance alloys at the surface could benefit the tribological performance in the forming operation. However, the research into high temperature tribological behaviour of AM materials in hot forming applications is very limited. The aim of this work is to study the tribological performance of additively manufactured materials. Two steels were used – a maraging steel and modified H13 tool steel. The hot work tool steel H13 is commonly applied for dies in metal forming processes. In this thesis it was used to study additive manufacturing as the processing route instead of conventional casting. The choice of a maraging steel is motivated by a possible application of high-performance alloys as a top layer on dies. The materials were post-machined and studied in milled, ground and shot-blasted conditions. The different post-machining operations were applied to study the effect of surface finish on the tribological behaviour and also to evaluate different methods of post-machining an AM surface. As fabricated dies are usually manufactured with milled surface. During its use, the dies undergo refurbishment after certain number of cycles and the surface condition is changed to a ground surface. These surface finishes are commonly tested for hot forming applications. The shot blasted operation was chosen as alternative surface finish. The process allows to prepare large sized tools easily and the surface has beneficial compressive stresses. The tribological behaviour of AM steels was studied using a hot strip drawing tribometer during sliding against a conventional Al-Si coated 22MnB5 steel. The workpiece temperature during the tests was 600 and 700°C. The results of the tribological performance of AM materials were compared to conventionally cast tool steel QRO90.The results have shown that the friction behaviour of both maraging and H13 steels at 600°C was stable and similar whereas at 700°C the COF was more unstable and resulted in an earlier failure of the tests due to increased material transfer of Al-Si coating from the workpiece surface.The main wear mechanisms for AM materials were galling and abrasion at both temperatures. Abrasion is more severe for the AM steels in comparison to cast tool steel QRO90. The galling formation on milled and ground surfaces showed similar behaviour to cast steel and it increased with higher workpiece temperatures. The shot-blasted surfaces showed less build-up of transferred material on the surface but folding of asperities and entrapment of Al-Si particles within surface defects generated during shot-blasting.

Additive manufacturing (AM) is an emerging and interesting technology that enables some of theproduct development projects (PDPs) to produce products that have mechanical and tribologicalproperties comparable to products that are conventionally manufactured. Selective laser melting(SLM) is an additive manufacturing technology that is predominantly used for the production of metalbased components (i.e. it could be pure metal, alloys, and metal matrix composites). This workevaluates and ranks two different steel grades produced with SLM technology in tribological andcutting tool applications at AB Sandvik Coromant. The two steel grades used in this work were Cofree maraging steel alloy and Co-free W360 AMPO alloy. Both the grades are Cobalt free, hencedeveloped as a sustainable alternative for the future. The W360 AMPO alloy is a hot-work tool steelwith high temperature wear resistance and heat resistance. The work covers the characterization ofmicrostructure and chemical composition, mechanical properties, and tribological properties toevaluate the performance of the tool steel grades when used as tool bodies in drilling applications.The microstructure and chemical composition of the additive manufactured and heat-treated tool steelswere analyzed using SEM and EDS. The mechanical properties were evaluated using micro-Vickersindentation and scratch testing while the tribological properties were evaluated using pin-on-disctesting where counter material used was quenched and tempered steel. The application test included asimulated chip wear test using chip breakers (CB’s) and an actual drilling test, both performed at ABSandvik Coromant. To study the effect of surface topography on the adhesion tendency, the simulatedchip wear test was performed on both milled and grounded chip breaker (CB) samples. The drillingtest was done with three different test-set ups; function test, 30° inclined exit, and forced tool life test.The cellular microstructure was observed on Co-free maraging steel alloy sample, while themicrostructure was tempered martensite in W360 AMPO alloy. Elemental analysis revealed thechemical composition of the two steel grades. The measured hardness for both the samples Co-freemaraging steel alloy and W360 AMPO was found to be within the specification of demands (50-52HRC), although the hardness of W360 AMPO was a bit higher than Co-free maraging steel alloy. Theresults of the pin-on-disc tests showed that the wear resistance of the W360 AMPO alloy issignificantly higher than that of the Co-free maraging steel alloy, the tribo-system used was similarwhen compared to the actual application. Also, after analyzing the pin made up of quenched andtempered steel 34CrNiMo6 (SS2541) it can be seen that due to the W360 AMPO sample the volumeloss of the pin is almost 4 times when compared to Co-free maraging steel alloy. The result from thesimulated chip wear test showed that W360 AMPO has better wear characteristics. Adhesion ofworkpiece material (SS2541) was observed on both samples. In the simulated chip wear test, thesurface topography effect was studied by performing a test on milled and grounded CBs. GroundedCBs showed less adhesion tendency compared with milled CBs on both samples but the wearcharacteristics were similar irrespective of the surface roughness. The result from the drilling testshowed wear scar was predominant on a drill with Co-free maraging steel alloy and a drill with W360AMPO alloy was intact. Future possible investigations proposed after findings from experimentalresults may lead to future work.

O aço maraging é conhecido pela sua alta resistência mecânica proveniente da formação de precipitados intermetálicos como Ni3Ti e Fe2Mo durante o envelhecimento, porém com subsequente perda de tenacidade à fratura. Existe uma vasta literatura sobre este tipo de aço, o qual é submetido a diversos tratamentos térmicos. Normalmente dois tratamentos térmicos são aplicados: uma homogeneização inicial para solubilização dos precipitados, sendo a recomendação geral 820 °C/1 h, e posteriormente o tratamento de envelhecimento, variando a temperatura de 455 °C a 510 °C e o tempo de 3 a 12 h. No entanto, pode haver variações no tratamento, como aquecimento após homogeneização numa faixa de temperatura intercrítica ou abaixo da Ac1 visando a reversão da martensita em austenita e o refino de grão. Até o presente momento, não está bem definida a influência da temperatura/tempo em tratamentos de temperaturas inter ou subcríticas que visam o refinamento da estrutura e o aumento da austenita retida/reversa. A literatura mostra tratamentos na liga maraging 300 por meio de estudos mais antigos, da década de 70 e 80, utilizando aquecimentos curtos e cíclicos para reversão e estabilização da austenita reversa. Estudos mais recentes de outras ligas utilizaram tratamentos isotérmicos para difusão e reversão da martensita em austenita. Nesta proposta serão pesquisadas as duas rotas de tratamento, cíclica e isotérmica, para avaliar a reversão martensita-austenita. Os tratamentos cíclicos foram caracterizados por EBSD, MEV e difração de raio-X ex-situ. Os tratamentos isotérmicos foram caracterizados por EBSD e difração de raio-X de fonte sincrotron in-situ, ou seja, medida em tempo real durante o tratamento. Ambas as condições foram avaliadas mecanicamente por meio de ensaios de flexão de 3 pontos. / Maraging steel is known for its high mechanical strength resulting from the formation of intermetallic precipitates such as Ni3Ti and Fe2Mo during aging heat treatment, with subsequent loss of fracture toughness. There is a vast literature on this type of steel, which is subjected to various thermal treatments. Normally two heat treatments are applied: an initial homogenization for solubilization of the precipitates, the general recommendation being 820 ° C/1 h, and later the aging treatment, varying temperature from 455 ° C to 510 ° C and time of treatment from 3 to 12 hours. However, there may be applied other heat treatments, such as heating after homogenization in an intercritical temperature range or below Ac1 for the reversion of martensite-to-austenite and grain refinement. To date, the influence of temperature and time on inter- or subcritical temperature treatments aiming at grain refinement and martensite-to-austenite reversion is not well defined. The literature shows treatments in the maraging 300 alloy, from the 70s and 80s, using short and cyclic heat treatment for reversion and stabilization of austenite. Recent studies of other alloys have used isothermal treatments for diffusion and martensite-to-austenite revresion. In this study, two heat treatment routes, cyclical and isothermal, were investigated to evaluate the martensite-to-austenite reversion. Cyclic treatments were characterized by EBSD, SEM and ex-situ X-ray diffraction. The isothermal treatments were characterized by EBSD and X-ray diffraction of synchrotron source in-situ, that is, measured in real time during the treatment. Both conditions were mechanically evaluated by 3-point-bending tests.