This thesis compared macrotexture measurements obtained using the volumetric method (Sand Patch) and three laser-based devices: MGPS system, ICC laser profiler, and Circular Texture Meter (CTMeter). The study used data from three sources: two controlled experiments conducted at the Virginia Smart Road, field data collected on eight newly constructed hot-mix-asphalt (HMA) roadway surfaces, and data collected on airport surfaces at the Wallops flight facility, Virginia. The data collected at the Virginia Smart Road, a controlled-access two-lane road that includes various HMA and concrete surfaces, was used for the main analysis. The other two sets of data were used for verification and validation of the model developed. The analysis of the data collected at the Virginia Smart Road showed that the CTMeter mean profile depth (MPD) has the highest correlation with the volumetric (Sand Patch) mean texture depth (MTD). Furthermore, texture convexity had a significant effect on the correlation between the measurements obtained with different devices. Two sets of models for converting the laser-based texture measurements to an estimated MTD (ETD) were developed. One set of equations considered all the data collected at the Virginia Smart Road, and the other excluded the measurements on the Open-Graded Friction Course (OGFC). The developed models were tested using measurements collected at eight roadway sections throughout Virginia and the Wallops flight facility. The model, excluding the OGFC section, was successfully applied to other sites. / Master of Science

No description available.

This diploma thesis deals with the relation between the longitudinal friction coefficient dependence on measuring speed and the value of road surface macrotexture MPD. Results of longitudinal friction coefficient and value of MPD measurement on 73 sections are included in this thesis. The results were compared by regression analysis and its outcome was used for determination of formula that enable calculation of longitudinal friction coefficient for any operating speed when longitudinal friction coefficient for 60 km/h and value of macrotexture are known. The evaluation scale for skid resistance index (SRI) was also determined in this thesis. It could be used for evaluation of skid resistance independently of the type of device used for friction coefficient measurement.

Non-exhaust PM10 is an issue in the urban environment linked to health issues. Emissions of non-exhaust PM10 is relatable to pavement properties. Also of importance is resuspension of road dust stored from surfaces. This depends on the traffic and metrological conditions. Given this, the purpose of the thesis was to give an overview limited to Sweden and the Nordic countries regarding non-exhaust PM10 emissions and road dust. The overview includes how particles are related to human health. Also included is the principle of how particles are emitted from road surface and tyre interaction, both directly and through resuspension of road dust. This thesis also includes an overview of how the use of studded tyres impact on asphalt surfacings and how the properties of the materials used impact on the abrasion wear. This is then linked to the emissions of non-exhaust particles. Further described is how measurements can be done of ambient particles and road dust, followed on two major models for road abrasion wear and non-exhaust PM prediction. Also included is how road operation, e.g. traction sanding and dust binding, influence the particle emissions together with other options to reduce the emissions through, e.g. limiting the use of studded tyres. One special issue discussed in this thesis is the lack of holistic view regarding the environmental problems in the urban environment with focus on particle emissions and road noise emissions, both from the road surface and tyre interaction. Currently the most problematic issue is prioritized and the resulting solution to that specific problem might increase other problems. This thesis shows that much knowledge is available regarding non-exhaust PM10 emissions and road dust, but also that several knowledge gaps exists. Several suggestions on further studies is given together with a brief overview on the continued work forward from this thesis. / Icke-avgasemissioner av PM10 är ett problem i urbana miljöer länkat till flera hälsoaspekter. Dessa emissioner kan relateras till beläggningars egenskaper. Även resuspension av vägdamm från ytor är av betydelse och beror på både trafiken och meterologin. Baserat på detta är syftet med denna avhandling att ge en översikt kring icke-avgas PM10 emissioner och vägdamm, begränsat till Sverige och de övriga nordiska länderna. Denna översikt inkluderar hur partiklar relaterar till människans hälsa. Annat som inkluderas är hur partiklarna emitteras från vägyta-däckinteraktionen, både direkt och genom resuspension av vägdamm. Avhandlingen inkluderar även en översikt kring hur användandet av dubbdäck inverkar på vägbeläggningar och hur dess egenskaper inverkar på nötningsslitage. Detta länkas därefter till partikelemissioner. Vidare beskrivs även hur mätningar kan genomföras av partiklar samt vägdamm vilket följs upp av beskrivningar kring två större modeller kring prediktion av nötningsslitage och prediktion av icke-avgasemissioner. Även hur driftåtgärder inverkar på emissionerna tillsammans med alternativ för att minska emissionerna tas upp. Ett särskilt problem som tas upp i avhandlingen är bristen på helhetssyn beträffande miljöproblem i den urbana miljön med fokus på partikel- och bulleremissioner från vägyta-däckinteraktionen. För närvarande brukar det värsta problemet prioriteras och lösningen till det detta problem kan i sin tur medföra att andra miljöproblem istället förvärras. Denna avhandling visar på att mycket kunskap existerar kring icke-avgasemissioner av PM10 och kring vägdamm, men även att flertalet kunskapsluckor existerar. Flertalet förslag på vidare studier ges tillsammans med en överblick kring det fortsatta arbetet. / <p>QC 20180202</p>