The major goals of this thesis were to (1) design and synthesize a supported catalyst with well-defined monodisperse palladium nanoparticles evenly distributed throughout an inorganic oxide substrate with tunable porosity characteristics, (2) demonstrate the catalytic activity of this material in the decarboxylation of long chain fatty acids and their derivatives to make diesel-length hydrocarbons, (3) elucidate the deactivation mechanism of supported palladium catalysts under decarboxylation conditions via post mortem catalyst characterization and develop a regeneration methodology thereupon, and (4) apply this catalytic system to a real low-value biofeedstock. In an effort to maximize loading and minimize mass transfer limitations, mesoporous silica MCF was synthesized as catalyst support. Functionalization with various silane ligands facilitated even distribution of palladium precursor salts throughout the catalyst particle, and, after reduction, monodisperse palladium nanoparticles approximately 2 nm in diameter. The Pd-MCF catalyst showed high one-time activity in the decarboxylation of fatty acids to hydrocarbons in dodecane at 300 °C. Subsequent reactions were performed on acid derivatives to elucidate a decarboxylation reaction pathway. The catalyst experienced severe deactivation after only one use and substantial effort was put into elucidating the nature of this deactivation via post mortem catalyst characterization. The deactivation was found not to be caused by nanoparticle sintering, agglomeration or ripening, but instead by organic deposition, mainly of reactant acid. A regeneration methodology was developed and subsequent catalyst reuse exhibited high activity. Finally, the Pd-MCF catalyst was applied to a wastewater-derived brown grease from a poultry rendering facility, in an unpolished and polished form. The latter was successfully decarboxylated to diesel-length hydrocarbons with high conversion and selectivity.

The use of novel hyperbranched aminosilica (HAS) materials created through the ring-opening polymerization of aziridine from mesoporous silica supports was proposed for the adsorption of CO2 from dilute sources. The limits of the adsorptive performance of these adsorbents were investigated via the preparation of sets of materials with a range of aminopolymer loadings on several different silica supports with different pore space characteristics. Relationships were determined between the materials' amine loadings and the CO2 adsorption performance. Adsorbents with substantial remaining pore volume displayed universal adsorption kinetics when normalized by amine loading. However, materials with blocked pores displayed substantially slower adsorption kinetics due to hindered mass transfer. In both humid and dry conditions, the HAS adsorbent was found to have a surprisingly large CO2 capacity in light of the 250-fold reduction in CO2 partial pressure from 10% CO2 (flue gas application) to 400 ppm CO2 (air capture application). Finally, a new series of linear aminosilicas was created through the reaction of existing aminosilicas with N-protected-aziridines. Specifically, reaction of aminosilane-functionalized silicas with N-methylaziridine resulted in the linear growth of methylaminoethyl groups, effectively increasing the amine loading of the adsorbent by a stoichiometric amount of an additional amine per attached silane.

Poor aqueous solubility is one of the greatest barriers for new drug candidates to enter toxicology studies, let alone clinical trials. This thesis focuses on contributing to solving this problem, evaluating the oral toxicity of mesoporous silica particles, and enhancing the apparent solubility and bioavailability of active pharmaceutical ingredients in vitro and in vivo using mesoporous silica particles. Toxicological studies in rats showed that two types of mesoporous silica particles given by oral administration were well tolerated without showing clinical signs of toxicity. Solubility enhancement, including in vivo bioavailability and in vitro intracellular activity, has been evaluated for selected drug compounds. Mesoporous silica was shown to effectively increase drug solubility by stabilizing the amorphous state of APIs, such as itraconazole (anti-fungal), dasatinib (anti-cancer), atazanavir (anti-HIV) and PA-824 (anti-tuberculosis). Itraconazole was successfully loaded into a variety of porous silica materials showing a distinct improvement in the dissolution properties in comparison to non-porous silica materials (and the free drug). Microporosity in SBA-15 particles has advantages in stabilizing the supersaturation state of dasatinib. Small pore sizes show better confinement of atazanavir, contributing to a higher dissolution of the drug compound. In the in vivo animal studies, NFM-1 loaded with atazanavir shows a four-fold increase in bioavailability compared to free crystalline atazanavir. PA-824 has a higher dissolution rate and solubility after loading into AMS-6 mesoporous particles. The loaded particles show similar antibacterial activity as the free PA-824. This thesis aims at highlighting some of the important factors enabling the selection of adequate mesoporous structures to enhance the pharmacokinetic profile of poorly water-soluble compounds, and preparing the scientific framework for uncovering the effects of drug confinement within mesopores of varying structural properties. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 2: Submitted. Paper 3: Submitted. Paper 5: Submitted.</p>

Surfactant-templated, sol-gel based methodologies for the synthesis of tailored, nanostructured, hybrid inorganic–organic materials are incredibly powerful and versatile. Although growth in this field has been explosive in recent decades, a lot of room remains to contribute to the design and synthesis of new materials, as well as the development of advanced applications. In the work described herein, we firstly explored the synthesis of thick, mesoporous organosilica films and their application as functional coatings for solution-based, fibre-optic heavy metal sensors. Notably, sub-ppm level detection was observed for the detection of Pb(II) in mixed aqueous–organic media in short timeframes, and progress has been made toward synthesizing organotitania films that would allow for heavy metal sensing in purely aqueous solution. Furthermore, the utility of these types of surfactant-templated, organically-functionalized, mesostructured coatings has been preliminarily extended to other types of optical devices for heavy metal sensing. We have also explored the use of designer amphiphilic, alkyl oligosiloxane precursors for the tightly-controlled formation of thin, self-templated, hybrid nanostructured films. Moreover, films bearing uniaxial 2D hexagonal alignment over macroscopic length scales were obtained using polymer-treated substrates to control the interfacial interactions between the film precursors and the substrate surface. In addition, a relatively mild UV / ozone treatment was employed to remove the alkyl moieties from the films to yield porous materials without catastrophic loss of the as-synthesized, mesostructural order. Lastly, novel chiral, binaphthylene-based, periodic mesoporous organosilica (PMO) materials have been prepared. With the aim of demonstrating chiral recognition with such materials, porous, co-continuous capillary monoliths have been synthesized and applied as chiral stationary phases in nano-HPLC and CEC. Notably, enantioselective interactions between our materials and a chiral acetal-based analyte have been observed. Quantification of these enantioselective interactions in chiral PMOs by isothermal titration microcalorimetry is also being pursued. It has thus been demonstrated that a wide array of different functional materials may be accessed through template-based synthetic strategies. By varying parameters such the starting monomers, the sol composition, and the interfacial interactions between reacting species and a given substrate (to name a few), the resulting materials may be tailored to meet the demands of new and emerging technologies. / Thesis (Ph.D, Chemistry) -- Queen's University, 2011-05-24 19:50:17.478

Ordered mesoporous silicas have been shown to have a variety of useful applications ranging from adsorbents for containments to supports for catalysts. While these materials have received a good deal of attention in the literature there is still much opportunity for new technologies. We present research describing a novel approach to incorporate functionality onto the pore surfaces of these materials as well as a highly active catalyst for the Suzuki-Miyaura reaction. Our approach to selectively graft functionality on to the pore walls of the mesoporous silicas SBA-15 and MCM-41 involves treating the materials loaded with a structure directing agent (SDA), with hexamethyldisilazane that passivates the external surface through silylation. Once the SDA is removed the mesopores can be functionalized selectively using standard methods. A test designed to look at the passivation layer is also described. The catalyst developed is designated Pd-SBA-15-SH(g) and it is active for the Suzuki-Miyaura reaction. The activity, recyclability and leaching of Pd-SBA-15-SH(g) was found to be superior to related materials. A mechanistic analysis suggests the catalyst is a reservoir for soluble Pd metal. A key challenge that is holding back wide scale application of ammonia borane (NH3BH3) as a hydrogen storage material for mobile applications is the dearth of regeneration strategies. Presented are our forays into the development of an organic hydride based regeneration strategy. The first phase of the project focused on the reaction between Hantzsch esters and B(C6F5)3. N-substituted Hantzsch esters were found to transfer hydride to boron in >90 % yield. Mechanistic analysis of the reaction suggests either a SET mechanism or a highly asynchronous transition state. A novel hydride transfer equilibrium promoted by B(C6F5)3 was observed and it operated at temperatures below -10 ºC. N,N-ditertbutyl-dihydroimidazole is also an effective hydride donor to B(C6F5)3 as well as other Lewis acids that are more relevant mimics to those invoked in regeneration schemes. When the redistribution of B(SPh)3 is carried out with N,N-ditertbutyl-dihydroimidazole in the presence of NEt3 and CH2Cl2 at 50 ºC, BH2(NEt)3(SPh) is formed. CH2Cl2 functions as a thiol scavenger under the reaction conditions. 1-Octene trapping experiments provided indirect evidence for the formation of diborane, a critical component in the regeneration of NH3BH3. / Thesis (Ph.D, Chemistry) -- Queen's University, 2011-09-09 14:51:54.697

No description available.

Mesoporous silica materials are versatile platforms for biological catalysis, isolation of small molecules for detection and separation applications. The design of mesoporous silica supports for tailored protein and biomolecule interactions has been limited by the techniques to demonstrate biomolecule location and functionality as a function of pore size. This work examines the interaction of proteins and lipid bilayers with engineered porous silica surfaces using spherical silica particles with tunable pore diameters (3 – 12 nm) in the range relevant to biomolecule uptake in the pores, and large particle sizes (5 - 15 µm) amenable to microscopy imaging The differentiation of protein location between the external surface and within the pore, important to applications requiring protein protection or catalytic activity in pores, is demonstrated. A protease / fluorescent protein system is used to investigate protein location and protection as a function of pore size, indicating a narrow pore size range capable of protein protection, slightly larger than the protein of interest and approaching the protease dimensions. Selective functionalization, in this case exterior-only surface functionalization of mesoporous particles with amines, is extended to larger pore silica materials. A reaction time dependent functionalization approach is demonstrated as the first visually confirmed, selective amine functionalization method in protein accessible supports. Mesoporous silica nanoparticles are effective supports for lipid bilayer membranes and membrane associated proteins for separations and therapeutic delivery, although the role of support porosity on membrane fluidity is unknown. Transport properties of bilayers in lipid filled nanoparticles as a function of pore diameter and location in the particle are measured for the first time. Bilayer diffusivity increases with increasing pore size and is independent of bilayer location within the core, mid or cap of the particle, suggesting uniform long range bilayer mobility in lipid filled pores. Application of lipid bilayers on mesoporous silica was examined for membrane associated proteins A unique method to adhere functional proteins in lipid bilayers on mesoporous silica particles is established using vesicles derived from cell plasma membranes and their associated proteins. This method of membrane protein investigation retains proteins within native lipid membranes, stabilizing proteins for investigation on supports.

The synthesis of mesoporous silica thin films using surfactant templating typically leads to an inaccessible pore orientation, making these films not suitable for membrane applications. Recent advances in thin film synthesis provide for the alignment of hexagonal pores in a direction orthogonal to the surface when templated on chemically neutral surfaces. In this work, orthogonal thin film silica membranes are synthesized on alumina supports using block copolymer poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (P123) as the template. The orthogonal pore structure is achieved by sandwiching membranes between two chemically neutral surfaces, resulting in 90 nm thick films. Solvent flux of ethanol through the membrane demonstrates pore accessibility and suggests a silica pore size of approximately 10 nm. The permeability of ions and fluorescently tagged solutes (ranging from 4,000 to 70,000 Da) is used to demonstrate the membrane’s size selectivity characteristics. A size cut off occurs at 69,000 Da for the model protein BSA. By functionalizing the silica surface with a long chained alkyl group using n-decyltriethoxysilane (D-TEOS), the transport properties of the membranes can be altered. Contact angle measurements and FTIR results show the surface to be very hydrophobic after functionalization. Solvent flux of ethanol through the silica thin film membrane is similar before and after functionalization, but water flux decreases. Thin film silica membranes show much promise for applications in catalysis, bio-sensing, and affinity separations.

The main theme of this dissertation is the fabrication and analysis of modified mesoporous silica membranes for separation applications. Synthesis methods for mesoporous silica membranes have been developed to enhance the transport performance and quality of the membranes, such as permeability, pore volume, and surface area. Then, synthesized membranes were modified with different organic groups to tailor selectivity in separations. The collected studies of modified mesoporous silica membranes showed that appropriate functionalization on newly synthesized novel membranes leads to promising structural and permeation properties. First, a seeded growth method was developed for synthesis of MCM-48 membranes on alumina supports, thereby extending the seeded growth technique used for zeolite membranes to mesoporous silica membrane synthesis. The surface properties of the MCM-48 membranes were then modified by silylation with hexamethyldisilazane (HMDS). In comparison to MCM-48 membranes previously synthesized by the in situ growth technique, much less silica infiltration into the alumina support was observed. The pore structure of the MCM-48 membranes demonstrated that a large accessible pore volume was available for molecular permeation and pore modification to tailor selectivity. The gas permeation properties of the calcined and silylated MCM-48 membranes were consistent with a Knudsen-like mechanism, albeit with a substantial influence of gas-solid interactions in the mesopores. The silylated MCM-48 membranes were evaluated for pervaporative separation of ethanol (EtOH), methyl ethyl ketone (MEK), and ethyl acetate (EA) from their dilute aqueous solutions. The synthesized membranes exhibited high pervaporative separation factors and organic fluxes. The selective separation of organic/water mixtures with MCM-48 membranes were attributed to both the organophilic nature of the surface and the effective pore size of the silylated mesopores. Next, the synthesis and organic/water separation properties of mesoporous silica membranes supported on low-cost and scalable polymeric (polyamide-imide) hollow fibers and modified by trimethylsilylation with HMDS was studied. Thin, defect-free membranes that exhibited high gas permeances consistent with Knudsen-like diffusion through the mesopores were prepared. Silylation of these membranes did not affect the integrity of the mesoporous silica structure and the underlying polymeric hollow fiber, but led to capping of the surface silanol groups in the mesopores with trimethylsilyl groups. The silylated mesoporous membranes were evaluated for pervaporative separation of EtOH, MEK, EA, iso-butanol, and n-butanol from their dilute aqueous solutions. The membranes showed higher separation factors than those of flat membranes, along with high organic fluxes. The large increase in hydrophobicity of the membranes upon silylation allowed upgrading of the feed mixtures to permeate streams with considerably higher organic content. The selective separation of organic/water mixtures with the fiber-supported mesoporous silica membranes was attributed to both the organophilic nature of the surface (yielding good adsorption selectivity) and the effective pore size of the silylated mesopores (giving good fluxes). Comparison with other types of organic/water separation membranes revealed that the present silylated membrane platform shows good promise for use in organic/water separation applications due to its high flux, scalable and low-cost fabrication methodology, and good separation factors that can be further enhanced by tailoring the mesopore modification chemistry. Further, the gas transport properties of aziridine-functionalized mesoporous silica membranes on polymeric hollow fibers have also investigated. The mesoporous membranes were amine-functionalized with aziridine and their transport properties were studied to understand the effects of surface functionalization on gas separations. This new hybrid aminosilica membrane showed interesting and counter-intuitive N₂ selective permeation properties in dry CO₂/N₂ separations. Detailed characterization of the membrane structure and its permeation behavior showed that such behavior was due to the strong adsorption of CO₂, leading to reduced gas flux because of CO₂-induced amine crosslinking in the mesopores. This hyper-branched aminosilica membrane showed CO₂ selective properties when applied to humid gas permeation. Water molecules in the humid gas affected the adsorption of CO₂ molecules by causing a lower degree of crosslinking, allowing facilitated transport of CO₂.

The exploration of functional materials to store renewable, clean, and efficient energies for electric vehicles (EVs) has become one of the most popular topics in both material chemistry and electrochemistry. Rechargeable lithium batteries and fuel cells are considered as the most promising candidates, but they are both facing some challenges before the practical applications. For example, the low discharge capacity and energy density of the current lithium ion battery cannot provide EVs expected drive range to compete with internal combustion engined vehicles. As for fuel cells, the rapid and safe storage of H2 gas is one of the main obstacles hindering its application. In this thesis, novel mesoporous/nano functional materials that served as cathodes for lithium sulfur battery and lithium ion battery were studied. Ternary lithium transition metal nitrides were also synthesized and examined as potential on-board hydrogen storage materials for EVs. Highly ordered mesoporous carbon (BMC-1) was prepared via the evaporation-induced self-assembly strategy, using soluble phenolic resin and Tetraethoxysilane (TEOS) as precursors and triblock copolymer (ethylene oxide)106(propylene oxide)70(ethylene oxide)106 (F127) as the template. This carbon features a unique bimodal structure (2.0 nm and 5.6 nm), coupled with high specific area (2300 m2/g) and large pore volume (2.0 cm3/g). The BMC-1/S nanocomposites derived from this carbon with different sulfur content exhibit high reversible discharge capacities. For example, the initial capacity of the cathode with 50 wt% of sulfur was 995 mAh/g and remains at 550 mAh/g after 100 cycles at a high current density of 1670 mA/g (1C). The good performance of the BMC-1C/S cathodes is attributed to the bimodal structure of the carbon, and the large number of small mesopores that interconnect the isolated cylindrical pores (large pores). This unique structure facilitates the transfer of polysulfide anions and lithium ions through the large pores. Therefore, high capacity was obtained even at very high current rates. Small mesopores created during the preparation served as containers and confined polysulfide species at the cathode. The cycling stability was further improved by incorporating a small amount of porous silica additive in the cathodes. The main disadvantage of the BMC-1 framework is that it is difficult to incorporate more than 60 wt% sulfur in the BMC-1/S cathodes due to the micron-sized particles of the carbon. Two approaches were employed to solve this problem. First, the pore volume of the BMC-1 was enlarged by using pore expanders. Second, the particle size of BMC-1 was reduced by using a hard template of silica. Both of these two methods had significant influence on improving the performance of the carbon/sulfur cathodes, especially the latter. The obtained spherical BMC-1 nanoparticles (S-BMC) with uniform particle size of 300 nm exhibited one of the highest inner pore volumes for mesoporous carbon nanoparticles of 2.32 cm3/g and also one of the highest surface areas of 2445 m2/g with a bimodal pore size distribution of large and small mesopores of 6 nm and 3.1 nm. As much as 70 wt% sulfur was incorporated into the S-BMC/S nanocomposites. The corresponding electrodes showed a high initial discharge capacity up to 1200 mAh/g and 730 mAh/g after 100 cycles at a high current rate 1C (1675 mA/g). The stability of the cells could be further improved by either removal of the sulfur on the external surface of spherical particles or functionalization of the C/S composites via a simple TEOS induced SiOx coating process. In addition, the F-BMC/S cathodes prepared with mesoporous carbon nanofibers displayed similar performance as the S-BMC/S. These results indicate the importance of particle size control of mesoporous carbons on electrochemical properties of the Li-S cells. By employing the order mesoporous C/SiO2 framework, Li2CoSiO4/C nanocomposites were synthesized via a facile hydrothermal method. The morphology and particle size of the composites could be tailored by simply adjusting the concentrations of the base LiOH. By increasing the ratio of LiOH:SiO2:CoCl2 in the precursors, the particle size decreased at first and then went up. When the molar ratio is equal to 8:1:1, uniform spheres with a mean diameter of 300-400 nm were obtained, among which hollow and core shell structures were observed. The primary reaction mechanism was discussed, where the higher concentration of OH- favored the formation of Li2SiO3 but hindered the subsequent conversion to Li2CoSiO4. According to the elemental maps and TGA of the Li2CoSiO4/C, approximately 2 wt% of nanoscale carbon was distributed on/in the Li2CoSiO4, due to the collapse of the highly ordered porous structure of MCS. These carbons played a significant role in improving the electrochemical performance of the electrode. Without any ball-mill or carbon wiring treatments, the Li2CoSiO4/C-8 exhibited an initial discharge capacity of 162 mAh/g, much higher than that of the sample synthesized with fume silica under similar conditions and a subsequent hand-mixing of Ketjen black. Finally, lithium transition metal nitrides Li7VN4 and Li7MnN4 were prepared by high temperature solid-state reactions. These two compounds were attempted as candidates for hydrogen storage both by density functional theory (DFT) calculations and experiments. The results show that Li7VN4 did not absorb hydrogen under our experimental conditions, and Li7MnN4 was observed to absorb 7 hydrogen atoms through the formation of LiH, Mn4N, and ammonia gas. While these results for Li7VN4 and Li7MnN4 differ in detail, they are in overall qualitative agreement with our theoretical work, which strongly suggests that both compounds are unlikely to form quaternary hydrides.