This thesis explores the analysis and fabrication of plastic hypodermic needles. The hypotheses for this work are that replacing metal hypodermic needles with plastic ones will reduce or eliminate the possibility of the second-hand infections from needle sticks and unsterlized reuse and will be more cost and time efficient to recycle. The most critical structural failure mode for plastic needles is buckling due to their shape (thin walled hollow column). The consideration of buckling is critical to avoid structural failure and to ensure reliability for medical applications. The buckling strength of a cannula is analyzed by analytic (Euler buckling theory) and finite element analysis (FEA) methods. A 22 gage needle model (OD 0.7mm, ID 0.4mm, Length 12.7mm) was analyzed. Euler buckling theory was used to calculate the critical buckling load. Numerical approaches using finite element analyses showed very similar results with analytic results. A skin model was introduced to simulate boundary conditions in the numerical approaches. To verify the results of the analyses, cannulas with the same cross-sectional dimensions were fabricated using a micro injection molding technique. To make the parts hollow, a core assembly of straightened wire was used. Using the tip of a 22 gage needle, cannulas with the inverse shape of an actual hypodermic needle were made. The structural (buckling) characteristics of cannulas were measured by a force-displacement testing machine. When buckling occurred, an arch shape was visible and there was an abrupt change in the load plot. Test results showed the relation between the needles length and the buckling load, which was similar to that predicted by Euler buckling theory. However, test values were 60% of the theoretical or analytical results. Several reasons to explain these discrepancies can be found. The first is that an unexpected bending moment resulted from an eccentric loading due to installation off-center to the center of the testing machine or to the oblique insertion. A cannula that was initially bent during ejection from the mold can add an unexpected bending moment. The quality control of cannulas can be another reason. Bent or misaligned core wires produce eccentric cannulas, and the thinner wall section can buckle or initiate fracture more easily. The last reason may be that Euler buckling theory is not fully valid in short cannula, because the axial stress reaches yield stress before buckling occurs. Inelastic deformation occurs (i.e., the modulus is reduced) during compression in short cannula. The Johnson column formula is introduced to explain this situation. Especially for the nylon nanocomposite material tested, a loss in modulus due to moisture absorption may be another explanation for the discrepancies.

Yes / The structural formation and development of isotactic polypropylene (iPP) upon the micro-injection molding process was investigated at different mold temperatures and molecular weights utilizing a real-time synchrotron radiation small angle X-ray scattering (SAXS) technique combined with a customized micro-injection molding apparatus. Shish-kebab structure and parent-daughter lamellae were found to be formed during micro-injection molding for all iPP samples. In the case of kebab lamellae, a considerable growth in the long period and in the average thickness of lamellar crystallites and amorphous domains is observed at initial stages of crystallization for samples molded at varying temperatures. This effect is caused by the successive formation of thin lamellae in the outer layer and thick lamellae in the inner layer during the manufacturing process as evidenced by the spatial distribution of the crystalline lamellae across the thickness. In addition, the length of the shish formation increases remarkably at the onset of crystallization, the extent of which is dependent on the mold temperature. Despite the large changes of the lamellar stacks and the shish misorientation, the final length of the shish remains essentially unchanged when varying mold temperature. Since there is a critical orientation molecular weight above which the chains are stretched and oriented to form stable shish, the iPP sample with a low molar mass exhibits an overall decrease in the scattering intensity of SAXS patterns compared to the high molecular weight polypropylene. / This work is financially sponsored by the National Key R&D Program of China (2018YFB0704200), National Natural Science Foundation of China (21674119, 21790342 and 51525305), and Royal Society Newton Advanced Fellowship, United Kingdom (NA150222).

Nowadays, the filling and solidification of macro-scale injection mouldings can be predicted using commercial CAE software. For micro-injection moulding, the conventional tools do not work for all process conditions. The reasons might be the lack of high quality database used in the simulation and the improperly specified boundary conditions which do not reflect the real state in the cavity. Special aspects like surface tension or "size dependent" viscosity might also be responsible for the inaccuracy of the simulations. In this paper, those aspects related to the boundary conditions were taken into consideration, especially the thermal contact behaviour and the melt compression in the barrel which affects not only the temperature of the melt due to the compression heating, but also reduces the actual volume rate in the cavity. It can be shown that the heat transfer coefficient between the melt and the mould wall has a significant influence on the simulation results. In combination with precise material data and considering the reduction of the volume rate due to the melt compression in the barrel, the heat transfer coefficient may be quantified by means of reverse engineering. In general, it decreases when either the cavity thickness or the injection speed increases. It is believed that a pressure dependent model for the heat transfer coefficient would be more suitable to describe the thermal contact behaviour in micro injection moulding. The melt compression in the barrel affects definitely the filling behaviour and subsequently the heat transfer in the cavity as well, which is especially true for micro parts of high aspect ratio.

Nowadays, the filling and solidification of macro-scale injection mouldings can be predicted using commercial CAE software. For micro-injection moulding, the conventional tools do not work for all process conditions. The reasons might be the lack of high quality database used in the simulation and the improperly specified boundary conditions which do not reflect the real state in the cavity. Special aspects like surface tension or "size dependent" viscosity might also be responsible for the inaccuracy of the simulations. In this paper, those aspects related to the boundary conditions were taken into consideration, especially the thermal contact behaviour and the melt compression in the barrel which affects not only the temperature of the melt due to the compression heating, but also reduces the actual volume rate in the cavity. It can be shown that the heat transfer coefficient between the melt and the mould wall has a significant influence on the simulation results. In combination with precise material data and considering the reduction of the volume rate due to the melt compression in the barrel, the heat transfer coefficient may be quantified by means of reverse engineering. In general, it decreases when either the cavity thickness or the injection speed increases. It is believed that a pressure dependent model for the heat transfer coefficient would be more suitable to describe the thermal contact behaviour in micro injection moulding. The melt compression in the barrel affects definitely the filling behaviour and subsequently the heat transfer in the cavity as well, which is especially true for micro parts of high aspect ratio.

Yes / High-throughput manufacturing of transdermal microneedle arrays poses a significant challenge due to the high precision and number of features that need to be produced and the requirement of multi-step processing methods for achieving challenging micro-features. To address this challenge, we report a flexible and cost-effective process chain for transdermal microneedle array manufacture that includes mould production using laser machining and replication of thermoplastic microneedles via micro-injection moulding (micromoulding). The process chain also incorporates an in-line manufacturing data monitoring capability where the variability in the quality of microneedle arrays can be determined in a production run using captured data. Optical imaging and machine vision technologies are also implemented to create a quality inspection system that allows rapid evaluation of key quality indicators. The work presents the capability of laser machining as a cost-effective method for making microneedle moulds and micro-injection moulding of thermoplastic microneedle arrays as a highly-suitable manufacturing technique for large-scale production with low marginal cost. / This research work was undertaken in the context of MICRO-MAN project (“Process Fingerprint for Zero-defect Net-shapeMICROMANufacturing”, http://www.microman.mek.dtu.dk/).MICROMAN is a European Training Network supported byHorizon 2020, the EU Framework Programme for Research andInnovation (Project ID: 674801). This research has also receivedfunding and support from two other Horizon 2020 projects:HIMALAIA (Grant agreement No. 766871) and Laser4Fun (GA no.675063).

Bacteria are known to adhere to surfaces, which allows for the formation of biofilms, possibly causing a surge in hospital-offset infections, perilous diseases, and in some cases, death. Although certain bacteria are present in the natural flora of the human skin, some present extreme clinical significance due to the ability to transmit and adhere, and can be resistant to antibiotics. They also evolve over time to survive in harsh environmental conditions. Current research reveals that design of plastic surfaces containing submicron structures, is becoming a popular approach to tackle issues concerning infection transmission, with inspiration being derived from biomimetics and self-cleaning surfaces, such as the surface of a gecko skin, and the hydrophobic wax layer of forest leaves. Main barriers to adoption include that these surfaces alone are difficult to manufacture on 3D products, expensive to fabricate on a large scale and do not last long when subjected to environmental wear. Replication of nano-scale ridges was carried out using micro-injection, and the various samples were characterised using a range of tools to determine physical and biomechanical parameters. The sample surfaces were then cultured with the pathogenic bacterium Staphylococcus aureus under several environmental conditions, and the results were statistically analysed to reveal that anti-fouling LIPSS (laser induced periodic surface structures) ridges perform better to reduce bacteria cell-substrate adhesion, when compared to flat surfaces, or surfaces containing dual structures (anti-fouling ridges combined with anti-wear walls). It was therefore demonstrated that nanotextured polymeric surfaces with hydrophobic characteristics have exceptional non-fouling properties, preventing S. aureus, a very significant bacterial strain, from initial adhesion, a critical primary mechanism in its ability to proliferate. Collectively, the findings of this study strongly support the literature, suggesting that the bacteria struggle to adhere onto polymeric topography with increased water contact angles and simple nanostructures. However, the addition of certain anti-wear micro-features increased bacterial adhesion, reducing the efficacy of the non-fouling nanostructures from preventing biofilm formation.

Procédé de moulage par injection de poudres est constitué de quatre étapes principales: la préparation des matières premières, moulage par injection, le déliantage et le frittage. Cette thèse présente les recherches sur deux aspects principaux: la micro-injection et frittage par micro -ondes. Les contributions principaux peuvent être conclues dans les quatre aspects suivants: Modification et complément de l'algorithme précédent pour la simulation du procédé de moulage par injection; L'évaluation et la mise en œuvre de l'effet de tension de surface en simulation pour micro-injection; Micro-ondes expériences de frittage de compacts basés sur l'acier inoxydable 17-4PH; Réalisation de la simulation de frittage à micro-ondes avec couplage de la multi-physique, y compris le chauffage à micro-ondes classique, le transfert de chaleur, et le supplément de modèle pour la densification de frittage de la poudre compacté / Powder Injection molding process consists off our main stages: feedstock preparation, injection molding, debinding and sintering. The thesis presents the research on two main aspects: micro injectionmolding and microwave sintering. The main contributions can be concluded in thefollowing four aspects: Modification and supplement of previous algorithm for the simulation ofinjection molding process; Evaluation and implementation of surface tension effect in simulation for micro injection; Microwave sintering experiments of compacts based on 17-4PH stainles ssteel; Realization of the microwave sintering simulation with the coupling of multi-physics,including the classic microwave heating, heat transfer, and the supplement of model for sintering densification of powder impacts